Siruba C007L C007LX Instruction book

使用說明書與零件圖

INSTRUCTIONS BOOK & PARTS LIST

C007L/C007LX

運動部位，謹防工傷事故

Moving part, beware of industrial accident

高壓部位，謹防觸電事故

High voltage, beware of electric shock

高溫部位，謹防燙傷事故

High temperature, beware of burns

禁止

Prohibited

地線的接線表示

Indication of ground wiring

如果忽視此標記而運行了錯誤的機械操作，保養時肯定會引起當事者

或第三者人員重傷或死亡。

如果忽視此標記而運行了錯誤的機械操作，保養時有可能會引起當事

者或第三者人員受傷及造成設備損壞。

索引 INDEX 頁/PAGE

3

Introduction

一般安全事項說明 GENERAL SAFETY INSTRUCTIONS 1

重要安全事項說明 IMPORTANT SAFETY INSTRUCTIONS 3

特別事項 WARNING 7

警告標籤 WARNING TAG 8

護針安全圖說 SAFETY ILLUSTRATION OF NEEDLE GUARD 9

搬運縫紉機 MOVING THE SEWING MACHINE 9

關於縫紉機的安裝位置 THE INSTALLATION POSITION OF THE SEWING MACHINE 10

規格 SPECIFICATIONS 10

安全開關及其功能 SAFETY SWITCH AND ITS FUNCTION 11

C007L/C007LX 一般車

定位器之安裝與調整

C007L/C007LX INSTALLATION AND ADJUSTMENT OF

SYNCHRONIZER 12

操作步驟 OPERATION PROCESS 13

各部件名稱 NAMES OF MAJOR PARTS 15

機種說明 THE DESCRIPTION OF THE MODEL 16

關於本機的

重要安全注意事項 IMPORTANT SAFETY INSTRUCTIONS OF THIS MACHINE 20

C007L/C007LX 直驅車

馬達安裝方式 C007L/C007LX INSTALL THE MOTOR 21

穿線方法 THREADING 22

拉線鬆緊度調整 ADJUST THREAD TENSION 22

針線挑線桿之調整 ADJUSTING NEEDLE THREAD TAKE-UP 23

壓具之調整 ADJUSTING PRESSER FOOT 24

差動比調整

1:0.6 ～1:1.1 ADJUSTING DIFFERENTIAL RATIO 1:0.6 ～1:1.1 24

4

差動比調整

1:0.9 ～1:1.4 ADJUSTING DIFFERENTIAL RATIO 1:0.9 ～1:1.4 25

差動送布牙的調節 ADJUSTING MOVEMENT OF DIFFERENTIAL FEED DOG 26

縫目長度之調整 ADJUSTING STITCH LENGTH 27

壓具壓力強度之調整 ADJUSTING PRESSURE OF THE PRESSER FOOT 28

操作環境照明 LIGHTENING OF THE OPERATION ENVIRONMENT 28

保養 MAINTENANCE 29

潤滑 LUBRICATION 30

針與線之冷卻與潤滑 LUBRICATE AND THE COOLING OF NEEDLE AND THREAD 31

潤滑油之更換 CHANGE THE LUBRICATION OIL 31

濾油器之更換 CHANGE THE OIL FILTER 32

針之更換 REPLACE THE NEEDLE 32

結束密縫調整 ADJUSTING END INTENSIVE SEWING 33

故障檢修 TROUBLESHOOTING 34

桌板圖 TABLE CUT-OUT 42

零件圖 PARTS LIST 45

報廢流程 DEMOLITION PROCEDURE 68

82dB(A)/4500rpm

C007L/C007LX Series

45

46

Net Weight(Kg)

一般安全事項說明 GENERAL SAFETY

INSTRUCTIONS

警告！

當使用這台機器，基本安全預防應恆被遵守

，以減輕火災、電擊、或是個人傷害的風險

。包含以下注意事項。

在操作這台機器之前，請閱讀所有說明並且

緊記於心。

1. 保持工作場所清潔

雜亂的環境與椅子會招引危害。

2. 考量工作場所環境

勿暴露電源於雨水之中、勿在溼氣重的地方

或潮濕的場所使用機械器具。保持工作場所

良好整齊。當有引發火災或爆炸危險時，勿

使用電源工具。

3. 免於電擊危害

避免身體接觸地線或是接地表面。(即：

管線，發熱物體，以及冷凍庫 )

4. 勿使孩童接近

不要讓訪客接觸工具或是延伸管線。

5. 適當的穿著

不要穿著寬鬆衣物或是穿戴珠寶，這可能被

活動零件拉扯而導致危險。穿戴護髮套可包

住長髮。

6. 不要任意拉扯電線

絕不要用電源端拉扯機器，或是從插座猛拉

電線來拔掉電線。使電線遠離熱源、油類或

是尖銳邊緣。

7. 謹慎保養機器

遵從指示來添加潤滑油或是更換附件。定期

檢測工具用線，如果有所損害，請使用合格

的維修器具來修復。

Warning!

When using this machine, basic safety

Precautions should always be followed to

reduce the risk of fire, electric shock and

personal injury, including the followings.

Read all these instructions before

operating this product and save these

instructions.

1. Keep work area clean

Cluttered areas and benches invite

injuries.

2. Consider work area environment

Do not expose power to rain. Do not use

machine tools in damp or wet locations.

Keep work area well lit.

Do not use power tools where there is risk

to cause any fire or explosion.

3. Guard against electric shock

Avoid body contact with earthed or

grounded surfaces (e.g. Pipes, radiators,

ranges refrigerators.)

4. Keep children away

Do not let visitors touch the tool or

extension code.

5. Dress properly

Do not wear loose clothing or jewelry,

they can be caugh in moving parts. Wear

protecting hair covering to contain long

hair.

6. Do not abuse the cord

Never carry the machine by cord or yank

it to disconnect it from the socket. Keep

the cord away from heat, oil, and sharp

edges..

7. Maintain machine with care

Follow instructions for lubrication and

changing accessories. Inspect tool cord

periodically. If damaged, have it repaired

by an authorized service facility.

P1

Introduction

8. 中斷機器電源

當不使用機器時、維修前、以及更換配件

時。

9. 避免誤啟動

不要以手指置於啟動開關上之後，搬運一個

已插入電源的工具。確定在插電之前，電源

開關是關閉的。

10. 檢查損害零件

在進一步使用器具之前，應該小心檢查並

確認損傷的零件或是穿戴保護器具來確認

零件會正確運轉並且呈現應有功能。

11. 警告

除了在這本使用說明手冊中建議的功能之

外，任何附件或是配件的使用，都可能會

導致個人傷害的危險。

12. 由合格人員來修理器具

所以修理工作應由合格的人員使用原始個

別零件來作修理。

連接電源的特別警示 !

1. 只可與有 "CE" 認證的按壓啟動裝置連接這

台機器。

2. 遵守此使用說明手冊來安裝控制裝置。

3. 在操作過程中，永遠保持機器適當的接地。

4. 在調整、更換零件、或是維修保養之前，必

須確定將插頭由插座拔出，以預防任何機器

意料之外的啟動而造成危害。

8. Disconnect machine

When not in use, before servicing and

when changing accessories.

9. Avoid unintentional starting

Do not carry a plug-in tool with a finger on

the switch. Ensure the power switch is off

when plugging in.

10. Check damaged parts

Before further use of the tool, a guard or

other part that is damaged should be

carefully checked to determine that it will

operate properly and perform its intended

function.

11. Warning

The use of any accessory or attachment,

other than those recommended in this

instruction manual, may present a risk of

personal injury.

12. Have your tool repaired by a

qualified person

Repairs should only be carried out by

qualified persons using original spare

parts.

SPECIAL WARNING FOR ELECTRIC

CONNECTION!

1. Incorporate this machine only with "CE"

certificate hold-to-run control device.

2. Follow the instruction manual device to

install control device.

3. Always earth machine appropriately

during operation.

4. Before adjustment, parts change or

servicing must be sure to pull out the plug

from socket to prevent the hazard of

unintentionally start of machine.

P2

重要安全事項說明 IMPORTANT SAFETY

INSTRUCTIONS

恭喜您購買本機器，為了使這台機器能獲

得最佳功能以及安全的操作，務必請正確

的使用這台機器，使用前請仔細閱讀使用

說明書，希望您能長期使用它。請記得將

此說明書放在容易取得的地方。

1. 當您使用機器時，除了以下事項外，請

注意其他基本安全措施。

2. 使用機器前，除了本使用說明書外，

請詳細閱讀其他相關說明書。此外，

請妥善保存此說明書，以便需要時可

以隨時取閱。

3. 先確認機器是符合貴國安全規定及標

準後，再使用機器。

4. 當機器完成操作時，所有安全配備必

須安裝就緒，在缺少所述安全配備下

操作是不被允許的，以免導致人員受

傷。

5. 此機器應由受過適當訓練之操作員操

作。

6. 為了安全，我們建議您配戴安全眼

鏡。

7. 以下情形，請先關閉電源或拔掉插頭 :

(1) 穿針線、導線片、天平等以及更換

梭子時。

(2) 更換針、壓具、針板、送具、頂針

片、車布導板，以及其他附屬配件

時。

(3) 維修工作時。

(4) 離開工作場所或工作場所無人看

顧時。

For operating safely and getting the

best functions of this machine, you must

operate it correctly. Please read and

follow the instructions of this manual,

and keep it at hand for future references.

We are confident that you will enjoy this

machine as much as we enjoy

manufacturing it.

1. Instead of the following instructions,

when you use this machine, please pay

attention to the basic safety measures.

2. Before using this machine, please read

this manual and all related instructions.

In addition, please keep this manual

for future needs.

3. Before using this machine, please

ascertain that it conforms with safety

standards and regulations of your

country.

4. When the machine is ready for

operation, all the safety equipments

must be ready. Operate this machine

without the specified safety devices is

not allowed.

5. This machine must be operated by a

properly trained operator.

6. For your own safety, we suggest you

wearing goggles.

7. Please turn off the power switch

or disconnect it for any one of the

circumstances of the followings:

(1) When threading needle(s), adjusting

thread Take-up(s), thread guide(s),

and/or replacing bobbin(s).

(2) When replacing needles, presser

feet, needle plates, feed dogs,

needle guards, cloth guides and

other parts or accessories.

(3) When repairing.

(4) When the operator leaves the

working place or leaves the

machine unattended.

P3

Introduction

8. 假如不慎讓機器及配件使用之油或油

脂，接觸到眼睛、皮膚或誤食時，請立

刻以水清洗接觸部位及就診。

9. 請勿擅自碰觸運轉中之零件或配件及注

意機器電源是否已開啟，以免導致人員

受傷。

10. 維修、修改及調整等工作，須由受過

適當訓練的技師或熟手為之。維修時

只許使用指定之零件。

11. 一般維修及檢查工作必須由受過適當

訓練的人員為之。

12. 電子零件維修及保養工作必須由資深

的電子技師為之，或由非常熟練的人

員檢查及指導，當發現零件損壞時，

請立刻停止機器運轉。

13. 在做裝有氣動式零件 (例如氣缸 )機器

的維修及保養工作前，機器連接空壓

機及高壓空氣必須予以關閉及卸除，

機器中殘存高壓氣體必須予以消除，

此外調整及性能檢查只能由受過適當

訓練的技師或熟手為之。

14. 機器使用一段時間，必須定期清理。

8. If grease, oil, or any fluid contacts your

skin or eyes by any chance, please

wash the contacted area completely

with clean water and consult a doctor.

Or, swallow any fluid mistakenly,consult

a doctor immediately.

9. Do not touch any functioning parts

and devices. Always attend to whether

power switch is on or off before

operating in order to prevent anyone

from getting hurts.

10. Qualified technicians are required

for adjustment, modification, and

repair. Only use assigned parts for

replacement.

11. Routine maintenance and service

must be performed by well trained

persons, or qualified technicians.

12. Maintain and check the electronic

parts must be done by qualified

electrician or well-trained persons.

If any electronic part damaged or

malfunctioned, stop the machine

immediately.

13. The air house has to be detached

from the machine and the compressor

or air supply has to be cut off before

repairing and servicing the machine

equipped with pneumatic parts such

as an air cylinder. Qualified technicians

or well-trained persons are required

for adjustment and repairs.

14. To ensure the best performance,

periodically clean the machine is

necessary.

P4

15. 為使機器能正常操作以及減少噪音，

機台務必平放地上，機器避免在強烈

噪音的環境下操作。

16. 選用適當的電源插頭，並由電子技師

將其安裝在機器上，且插頭必須插在

接地線之插座上。

17. 機器只允許被使用於指定用途上，其

他用途是不允許的。

18. 修改或變更機器必須依照安全規定及

標準，同時採取有效的安全措施或變

更機器所引起損壞之責。

19. 警告提示以兩種符號標示：

(1) 對操作員或服務人員之傷害危險，也

為了避免觸電之危險，請勿打開馬達

電器箱之外蓋，也不要觸摸電器箱裡

面之零件。

(2) 必須特別注意事項

a. 絕對不可在移動外蓋，手指保護蓋或

安全配件後，進行機器操作，以免

導致人員受傷。

b. 為了避免被機器纏住，當機器運轉

中，您的手、頭髮及衣服，需遠離

手輪；此外這些部位周圍不可放置

任何物品，以免導致人員受傷。

15. In order to operate properly and to

reduce the noise, please place the

machine flat and level on the ground.

Avoid operating the sewing machine

at a noisy surrounding.

16. Select a proper power plug and install

it by an electrician. Please connect the

power plug to a grounded receptacle.

17. This machine can only be used for

the designed purpose. Other uses of

this machine are not allowed.

18. Any modification or conversion made

on this machine must be conformed

with the safety standards and

regulations. Precaution is necessary.

No responsibility will our company

take for damages caused by any

modification or conversion of this

machine without permission.

19. Two safety warning signs are applied

as warning signs:

(1) For the safety of operators and

service persons, please don't open the

cover of any electronic control boxes

of motor or other devices and don't

touch any components inside to avoid

electrical shock hazards.

(2) Always keep in mind:

a. Please never operate this machine

without outer cover, finger guard or

any safety device to avoid physical

injury.

b. Please keep your hair, fingers and

clothes away from the hand wheel

while the machine is in operation,

as well as never put anything near

these parts, to prevent the risk of

injuries by tangled into them.

P5

Introduction

c. 當您打開電源開關後或機器已在運轉

中，絕不可將您的手放在針的下方或針

線控線桿外蓋中，以免導致人員受傷。

d. 當機器運轉中，梭頭高速轉動，為了避

免對手可能引起之傷害，必須確定您的

手保持遠離梭頭附近。此外，當更換梭

子時，確定電源開關已關閉，以免導致

人員受傷。

e. 當放置或抬起機器時，小心勿將手置於

機器中，以免導致人員受傷。

f. 為了避免機器突然啟動而引起可能意

外，當機頭傾斜時，請關掉機器電源，

以免導致人員受傷。

g. 如果您的機器是配置伺服馬達，機器於

靜止狀態時，馬達是不會產生噪音的，

為了避免機器突然啟動而引起可能意

外，故請關掉機器電源。

h. 為了避免觸電之危險，請絕不要在移開

電源接地線後操作機器。

i. 為了避免觸電或電子零件損壞而引起之

可能意外，請先切斷電源，再插上或拔

掉插頭。

c. Please never put your fingers under

the needle(s) or in the thread take-up

cover to prevent physical injuries when

you turn on the power switch or operate

the machine.

d. While the machine is in operation, the

hook rotates at a high speed. Please

keep your hands away from the area

of hook to prevent any potential injury

to your hands. In addition, please

make sure to turn off the power of the

machine while changing bobbins.

e. Be careful and do not place your

fingers inside the machine when

placing or lifting the machine head to

avoid possible physical injuries.

f. Please turn off the power before tilting

the machine head to avoid possible

accidents due to abrupt start of this

machine.

g. For machine equipped servo motors,

the motors do not produce noise while

the machines are at rest. Therefore,

please turn off the power of this

accidents due to abrupt start of the

machine.

h. Never operate the sewing machine after

the ground wire is removed to avoid

electrical shock hazards.

i. Please turn the power switch off before

connecting or disconnecting the power

plug to prevent possible accidents due

to electric shock or damaged electronic

components.

P6

特別事項 WARNING

為了避免機器故障及損壞，請先確定以下

事項：

1. 當您安裝好機器後，做第一次機器操作

前，請徹底清潔機器。

2. 清除運送途中累積之灰塵及溢出之油

脂。

3. 確定電壓及馬達相數 ( 單相或三相 ) 安

裝正確。

4. 確定電源插頭正確地接上電源。

5. 當使用電壓與標示電壓不同時，請勿使

用機器。

6. 確定機器轉動方向是否正確。

警告：

在操作或調整本書中所提到之各步驟

前，請先將電源關掉，以免因為機器突

然啟動造成之意外。

Please confirm the followings to avoid

malfunction or damage to this machine.

1. After installing the machine, and before

the first operation, please clean it

completely.

2. Clean all dust and overflowed oil during

transportation.

3. Confirm that the voltage and the phase

(single or 3 phase) of motor are set

correctly.

4. Confirm that the power plug is correctly

connected to the power supply.

5. Never use the machine when the

local voltage type is different from

the marked voltage on the nametag

attached on the machine.

6. Confirm that the rotating direction of

the machine pulley is correct.

Warning:

Before doing any operation or any

adjustment described later in this

manual, please turn the power off to

prevent accidents caused by abrupt

start of the sewing machine.

P7

Introduction

警告標籤 WARNING TAG

P8

(圖1、2)

商店聯繫

②②

圖3/Fig.3

圖1/Fig.1 圖2/Fig.2

說明

③

護針安全圖說 SAFETY ILLUSTRATION OF

NEEDLE GUARD

搬運縫紉機 MOVING THE SEWING MACHINE

P9

Introduction

(圖5)

圖4/Fig.4

圖5/Fig.5

壓具防護裝置如圖 4

30.35mm 4mm

4mm

關於縫紉機的安裝位置 THE INSTALLATION POSITION OF

THE SEWING MACHINE

規格 SPECIFICATIONS

P10

(圖6)

圖6/Fig.6

設備

應將

造

1.C007L / C007LX 使用馬達：

(1)SIRUBA T41xxx （定位馬達）

(2)SIRUBA DCTxxx（伺服馬達）

2. 使用馬力：1HP（定位馬達）或

600W( 伺服馬達 )

3. 皮帶輪尺寸：直徑 90mm-110mm

( 出廠設定值為 90mm)

4. 空壓式：有效空氣壓 3.5kg/

5. 電磁閥電壓 24V 直流

6. 旋轉式電磁鐵電壓 30V 直流

註：

(1) 馬達使用之電壓、頻率、相數，於訂貨

時規定之。

(2) 馬達之功能調整請參閱馬達使用說明書。

1.C007L / C007LX Motor types：

(1)SIRUBA T41xxx （position motor）

(2)SIRUBA DCTxxx（servo motor）

2.Horse power：1HP for position motor/

600W for servo motor.

3.Size of motor pulley：90mm-110mm in diameter

(standard is 90mm)

4.Air pressure type：Minimum required pressure is

3.5kg/ .

5.The voltage of the solenoid is DC 24V.

6.The voltage of the rotary electromagnet is DC

30V.

Note：

(1)Motor voltage ,hertz and phases have

to be specified clearly while ordering.

(2)All details regarding to the

motor adjustment,please refer to the

motor operation manual.

安全開關及其功能 SAFETY SWITCH AND ITS FUNCTION

P11

Introduction

壓

驅

壓

圖

驅

圖

間

圖

回

開

點

開開

造

應

避

點

圖7/Fig.7

(UT776)

圖8/Fig.8

圖9/Fig.9

C007L/C007LX 一般車定位器之安

裝與調整

C007L/C007LX INSTALLATION AND

ADJUSTMENT OF SYNCHRONIZER

P12

1

3

2

1

3

2

1. 將隱藏式定位器①壓入車頭長溝②後，再以

螺絲③鎖緊。(圖8)

2. 在連接各部接線或接頭時應注意先關閉電源

開關。

3. 確認針棒在上定位時，車頭上之記號①應

與手輪②上所標示的刻劃③上方一小刻劃對

齊。(圖9)

1.Press the hidden synchronizer ① into the

long channel of the machine head ② ,and

then tighten the screw ③。(Fig. 8)

2.Before connecting each wires or plugs,

please check that all the electric switches

are turned off.

3.Ensure needle bar is at the highest

position, and the symbol on machine head

should be aligned with one upper scale at

the hand pulley.(Fig. 9)

操作步驟 OPERATION PROCESS

P13

Introduction

(圖10)-1

壓

開

壓

開

壓

開

處

當

回

壓

開

當(圖10)-2

當(圖10)-4

高點

(圖10)-2

(圖10)-3 (圖10)-4

壓

UTP-L UTR-L

UTQ-L

UTS-L

UTP-L UTR-L

UTQ-L

UTS-L

圖10/Fig.10

P14

壓

開

1. 前壓 (開始車縫 )

2. 中央 (壓具下放 )

3. 後半壓 (壓具提升 )

4. 後壓 (自動切線裝置 )

UTR-L UTS-L

各部件名稱 NAMES OF MAJOR PARTS

圖11/Fig.11

P15

Introduction

壓

過

調

壓具調整螺絲 Presser Foot Adjusting Screw

P16

機種說明 THE DESCRIPTION OF THE

MODEL

種類及規格說明

1. 型號及分類表示

letter K. Ex:C007L.

①表示機種別：

C= 筒式三針車。

②表示車台外觀改良之區分編碼，由 K然後

L，以英文字母排列，如 C007L。

③表示微油車。

④W有上叉縫 (圖12)。

U 無上叉縫 (圖13)。

①

②

③

④

C007LX - W122 - 240 / CH

① ②③ ④ ⑤ ⑥ ⑦ ⑧ ⑨

represents Semi-Dry.

圖12/Fig.12

圖13/Fig.13

ページを読み込んでいます...

Siruba C007L C007LX Instruction book

Siruba C007L C007LX Instruction book

他の言語で

関連論文