Sony Security Camera Security Camera ユーザーマニュアル

NSR Series

3-869-887-21 (1)

Network

Surveillance

Recorder

Installation Manual Page 2 __________________________________

GB

設置説明書 Page 29 _______________________________________

JP

Manuel d’installation Page 59 ________________________________

FR

Installationsanleitung Page 88 ________________________________

DE

Manuale all’installazione Page 118 ____________________________

IT

Manual de instalación Page 147 ______________________________

ES

Page 177 _________________________________________

CS

L

Table of Contents

2

Table of Contents

Usage Precautions ................................................. 3

Overview ................................................................ 4

System Requirements ............................................ 5

Package Contents .................................................. 6

Features and Functions ......................................... 7

Front ................................................................... 7

Rear .................................................................... 9

Installation ........................................................... 11

Installation Without a Rack .............................. 11

Rack Mount Installation ................................... 12

Connecting a Monitor ...................................... 14

Connecting the Keyboard, Mouse and Remote

Control Unit (RM-NS10) ............................... 14

Connecting the Power Cord ............................. 14

Connecting the Network Cable ........................ 14

Connecting a Network Camera ........................ 15

Connecting Other Devices ............................... 15

Connecting Remote Client ............................... 15

Turn the Power On and Off ................................ 16

Turning On the Power ...................................... 16

Turning Off the Power ...................................... 16

Basic Configuration ......................................... 16

Camera IP Address Configuration and

Registration to NSR ....................................... 19

Reconstructing Data Volume (Changing RAID

Types) (Only the NSR-100/50) ............................ 21

STATUS LED ....................................................... 23

Miscellaneous ....................................................... 24

LICENSE AGREEMENT ................................ 24

Concerning GPL-LPGL ................................... 24

MPEG-4 Video Patent Portfolio License ......... 25

Troubleshooting ............................................... 25

I/O Port ................................................................. 27

Pin Assignment of I/O Port .............................. 27

Using the I/O Receptacle ................................. 27

Wiring Diagram 1 for Sensor Input .................. 27

Wiring Diagram 2 for Sensor Input .................. 27

Wiring Diagram for Alarm Output ................... 28

Trademarks

• “IPELA” and are trademarks of Sony Corporation.

• Microsoft and Windows are either registered trademarks or trademarks of

Microsoft Corporation in the United States and/or other countries.

• Ethernet is a registered trademark of Fuji Xerox Co., Ltd.

• Other products or system names appearing in this document are trade-

marks or registered trademarks of their respective owners.

Further, the ® or ™ symbols are not used in the text.

Before using the recorder, be sure to read this manual.

Disclaimer of liability for recorded content

Sony Corporation does not accept any liability whatsoever for any problems

arising from a failure to record, or from damage or erasure of recorded con-

tent on this equipment, for any reason. This includes claims for compensa-

tion of recorded content, and for any concomitant and consequential

damages. Sony Corporation will not repair, restore, or duplicate any recorded

content. Your use of this product is subject to these conditions.

Before reading this manual

Be sure to read the “Important Safeguards” supplement.

• Reproduction or duplication, in whole or part, of the software or operation

manual supplied with the recorder, as well as renting or leasing of the

software without the authorization of the right holder is prohibited under

copyright law.

• Sony assumes no responsibility for damages, loss of income, or any

claims from a third party arising out of use of the recorder or supplied soft-

ware.

• For complete terms and conditions of the warranty for the recorder, refer

to the warranty card included in the package.

• The software supplied with the recorder cannot be used with any other

recorders.

• It is not possible to install any software into the equipment other than the

software supplied by Sony specifically for use with the equipment.

• Note that the specifications of the recorder and supplied software are

subject to change for improvement without prior notice.

• The recorder uses high security MD5 for password saving.

Usage Precautions

3

Usage Precautions

Important Information About Safety

• The electrical specifications of this unit are as follows.

Be sure to connect the unit only to a power source that

conforms fully to these requirements.

- Voltage: 100 - 127 / 200 - 240 V AC

- Current consumption: 8/4 A

- Line frequency: 50/60 Hz

• Use only the supplied power cord. Do not coil the

power cord or bundle it with other cords. Do not piggy

back connections. If current ratings are exceeded,

there is a risk of fire and other accidents.

• Make sure that all AC outlets and power cords are

properly grounded.

• Do not use the unit with the cover or case opened or

removed. Otherwise there is a risk of fire and electric

shock. Do not attempt to open or remove the cover or

case yourself. Always consult your supplier if opening

is necessary.

Important Information About Installation

Locations for use/storage

To prolong the life of the product, avoid use or storage

in the following locations.

• Locations that can become extremely hot or cold. (The

allowable usage temperature range is +5 ºC to +40 ºC/

+41 ºF to +104 ºF.)

• Locations exposed for an extended time to direct

sunlight, and locations near heating appliances. (Note

that the temperature in a closed car in summer can

exceed +50 ºC/+122 ºF.)

• Locations with high levels of humidity or dust

• Locations subject to strong vibrations

• Locations subject to strong magnetic fields

• Locations in the vicinity of radio or TV transmitters

creating a strong magnetic field

Do not block the ventilation openings

• The ventilation openings on the sides of the unit serve

to prevent internal heat buildup. Always leave a

clearance of at least 10 cm (4 inches) on both sides as

well as behind and above the unit.

• Do not use the unit in a closed box or other enclosure.

• Make sure that there are no cables or other objects in

the vicinity of the fan opening on the rear of the unit.

If the opening is blocked, internal heat buildup can

occur, leading to the risk of fire and damage.

• Also when the unit is installed in a rack, you must

make sure that the fan opening on the rear as well as

the ventilation openings on the front are not blocked

by cables or other objects. Do not install the unit in an

environment where the above requirements cannot be

met.

Use the unit in a horizontal position

• The unit is designed to be operated in a horizontal

position.

• Do not install the unit on a slanted surface, and protect

the unit from shocks.

• When the unit is dropped or otherwise subject to

strong shocks, it can be seriously damaged.

• When installing the unit in a rack, make sure that a

horizontal position is maintained. If the unit is not

properly levelled, malfunction may occur. Also, it is

highly recommended to properly anchor the rack to a

wall or similar, so that it cannot topple over.

Maintenance

• Before cleaning the unit or performing any other kind

of maintenance, be sure to disconnect the power cord

from the AC outlet.

• For cleaning, lightly wipe the cabinet and panels with

a dry cloth. To remove stubborn stains, lightly moisten

the cloth with a mild, neutral detergent and wipe with

a dry cloth afterwards.

• Do not use cleaning alcohol, solvents, benzine,

insecticide, or any other volatile substances, because

these may damage the finish and lead to discoloration.

• Dust can accumulate in the ventilation openings on the

front of the unit. When removing the dust, make sure

that you do not subject the unit to shocks or vibrations.

Transport

Use the original packing material or similar packing to

protect the unit from shocks.

Precautions for products with built-in

HDD

This unit has a built-in hard disk drive (HDD). The HDD

is a precision device. If subject to shock, vibration, static

electricity, high temperature or humidity, data loss can

occur. When installing and using the unit, closely

observe the following precautions.

Protect from shocks and vibrations

When subject to shocks or vibrations, the HDD can be

damaged and loss of data on the HDD can occur.

• When transporting the unit, use the specified packing

material. When transporting on a dolly or similar, use

a type which does not transmit excessive vibrations.

Excessive shocks and vibrations can damage the

HDD.

• Never move the unit while it is powered. Also before

removing or inserting the unit in a rack, make sure that

power is off.

• Protect all HDD-equipped devices in the rack from

shocks.

• Before removing or inserting the unit in a rack, make

sure that power to any other HDD-equipped devices in

the rack is also switched off.

• Do not remove panels or outer parts of the unit.

GB

Overview

4

• When placing the unit on a floor or other surface,

make sure that the unit is equipped with the specified

rubber feet, and put the unit down carefully. If there

are no feet, mount the rubber feet first. Do not place

the unit near other devices that may become a source

of vibrations.

Wait for 30 seconds after turning power off

For a brief interval after the power is turned off, the

platters inside the HDD will still keep spinning and the

heads will be in an insecure position. During this

interval, the unit is more susceptible to shocks and

vibrations than during normal operation. For a period of

at least 30 seconds after turning power off, avoid

subjecting the unit even to very light shocks. After this

period, the hard disk will be fully stopped and the unit

can be manipulated.

Temperature and humidity related precautions

Use and store the unit only in locations where the

specified temperature and humidity ranges are not

exceeded.

Temperature range for operation: +5 to +40 ºC

(+41 to +104 ºF)

Humidity range for operation: 20 to 80% relative

humidity (maximum wet-bulb temperature 30 ºC/

86 ºF, no condensation)

Temperature range for storage: –20 to +60 ºC

(–4 to +140 ºF)

Humidity range for storage: 20 to 90% relative

humidity (maximum wet-bulb temperature 40 ºC/

104 ºF, no condensation)

When HDD seems to be faulty

Even if the HDD is showing signs of malfunction, be

sure to observe all the above precautions. This will

prevent further damage from occurring until the problem

can be diagnosed and corrected.

HDD replacement

The HDD, fan, and battery of the unit are consumable

parts that will need periodic replacement. When

operating at room temperature, a normal replacement

cycle will be about two to three years. However, this

represents only a general guideline and does not imply

that the life expectancy of these parts is guaranteed.

Regarding parts replacement, consult your supplier.

Overview

The NSR series is a hard disk recorder for network

cameras. The NSR allows you to monitor and record

network camera images (JPEG or MPEG-4). It also

allows you to play back the recorded images and search

through it, making the NSR a truly versatile monitoring

system.

Control compatible cameras from remote

locations

You can pan, tilt, and perform zoom operations of

compatible cameras.

Compatible with analog cameras

You can monitor and record images from analog

cameras when you purchase and install an optional

camera server (SNT-V704).

Large-capacity hard disks allow recording for

long periods of time

The

NSR

is equipped with large-capacity hard disks. The

NSR-100 can record up to approximately 920 GB

1)

of data,

the NSR-50 can record up to approximately 460 GB

1)

of

data, and the NSR-25 can record up to approximately 230

GB

1)

of data. For example, if you record images from 16

cameras at 1 fps

2)

VGA, JPEG; one frame equals about 31

KB) with the NSR-100, you can record approximately a

month’s worth of images (15 hours a day)

3)

1) Includes the database capacity managed by the internal

software.

2) fps: frames per second.

3) When set to RAID 0.

Slim type (2U), space-saving 19-inch rack

mounting model

With the optional rack mounting kit (sold separately),

the unit can be installed in a standard universal pitch EIA

19-inch rack.

High-resolution up to 480 fps (VGA, JPEG)

recording

The NSR-100 can support up to 64 cameras, the NSR-50

can support up to 32 cameras, and the NSR-25 can

support up to 20 cameras. The NSR-100 records images

at a total frame rate of 480 fps* (240 fps with the

NSR-50, 120 fps with the NSR-25), VGA (640 × 480

pixels) resolution, JPEG (1 frame approx. 31 KB) image

format, for a crisp image quality.

* Maximum frame rate when 16 cameras are connected to the

recorder. Each camera has a frame rate of approximately 30

fps. This frame rate may become less because of

fragmentation on the internal hard disks. Values are based

on Sony measurements. These values are not guaranteed, as

performance may change due to the user’s operating

environment.

System Requirements

5

High reliability

The NSR-100/50 performs high reliability through:

• NSR-100: RAID 0, 1+0, and 5

• NSR-50: spanning*

and RAID 1

When used with a RAID 1, 1+0 or 5, the system can

continue functioning even if one of the hard disks develops

a malfunction. Similarly, because the system software and

settings are stored on the internal flash memory of the

NSR, if the system software develops a malfunction,

lightning-quick restoration of the system is possible. The

NSR also supports uninterruptible power supplies

(UPS)**, making them extremely reliable systems.

* Spanning: Function allowing several hard disks to be

virtually seen as one.

** Sony recommendation only.

Notes

• When you use RAID 0 with the NSR-100 or spanning

with the NSR-50, there is no data redundancy. Also,

storage capacity varies according with the RAID level.

• RAID is not available for the NSR-25.

Other features

• You can display the images from up to 64 cameras

(8 × 8 images) on one screen.

• The NSR is capable of manual, scheduled, and alarm

recording, among others.

• The NSR is equipped with a motion detection

function

1)

(Video Motion Detection (Recorder)).

• Run searches for recorded images by camera name,

date, alarm, and other methods.

• Create privacy zones by using the dynamic masking

functions

2)

. Dynamic masking covers pan, tilt, and

zoom.

• Precise alarm processing is made possible by

performing the various types of filtering

3)

that use the

image processing results sent from the camera in the

form of object information metadata. Because filtering

can be applied to metadata that has already been

recorded, you can also search for areas of interest after

recording is finished.

• Audio recording and playback

4)

are also supported

from compatible cameras.

1) Some functions are limited depending on the number of

cameras connected.

2) Some functions are limited depending on which camera

models are connected.

3) To perform motion detection and object detection using

metadata, a camera that supports motion detection by

metadata is required. The use of metadata is supported for

up to 32 cameras.

4) The optional active speakers are required.

Important

This manual only describes how to install and configure

the NSR. For detailed explanations about how to use the

recorder, refer to the “User’s Guide” (PDF) on the

supplied “NSR Series Manual, Tool & Source Codes CD”.

System Requirements

The hardware required in order to use this recorder are

as follows.

• Sony Network cameras

Contact your dealer for details about compatible Sony

network cameras.

• Monitor

1)

• USB Keyboard

2)

•USB Mouse

3)

• Network switch

• 1000Base-T/100Base-TX/10Base-T cable

• CF (CompactFlash) card or USB memory device

4)

1) For details about monitors supported by the NSR, contact

your retailer.

The following “Generic” type monitors can be selected.

Frequency is indicated at the end of each line.

- Generic LCD Display; LCD Panel 1024×768; 40-70

- Generic LCD Display; LCD Panel 1280×1024; 50-75

- Generic LCD Display; LCD Panel 1600×1200; 60

- Generic CRT Display; Monitor 1024×768; 50-70

- Generic CRT Display; Monitor 1280×1024; 50-90

- Generic CRT Display; Monitor 1600×1200; 50-90

The following resolutions can be specified.

- XGA (1024×768)

- SXGA (1280×1024)

- UXGA (1600×1200)

2) Use a USB keyboard with a cable. However, keys other

than the standard may not function. Wireless or infrared

USB keyboards may also not function properly.

3) Use a USB mouse with a cable. However, three-button or

wheel mice may not function properly. Wireless or infrared

USB mice may also not function properly.

4) Required when backing up system information such as

logs.

- For CF, use a card that has been formatted in advance

with VFAT.

- For USB memory, use a device that supports general

USB Mass Storage Class specifications.

- CF cards are not compatible with the NSR-25.

Package Contents

6

Package Contents

Check that the following items are included in this

package:

• NSR-100, NSR-50, or NSR-25 Surveillance Recorder

(1)

• Front panel key (2)

• Installation Guide (this document) (1)

• Remote Control Unit Operation Card (1)

• NSR Series Recovery CD

(1)

• NSR Series Manual, Tool & Source Codes CD

(1)

• Important Safeguards (1)

• Safety Notice (1)

• Warranty booklet (1)

• Rubber feet (4)

Notes

• This package may contain additional hardware and/or

documentation for those options.

• Save the boxes and packing materials for future use.

• The rack mounting kit is optional (sold separately). To

order a rack mounting kit, contact your retailer.

• The following are included on the NSR Series

Manual, Tool & Source Codes CD.

Manual folder: User’s Guide and Remote Control

Unit Operation Card data (multilingual)

SourceCode folder: Source code for GPL/LGPL-

compliant software

Tool: Remote client software (RealShot Manager),

CAM file playback application (Media File

Player), and accompanying user’s guides

Features and Functions

7

Features and Functions

Front

NSR-100/50

A Power LED

Alternates between green and amber lights when the unit

is starting up.

Lights green when startup is complete.

Lights amber when it is on standby.

B Network LED (1 to 3)

Lights green when there is activity at the corresponding

LAN connector at the rear of the NSR.

C HDD LED

Blinks green when the internal hard disks are accessed.

Lights amber when an error occurs with a hard disk.

D Status LED (1 to 4)

Lights in sequence (1, 2, 3, 4) when the NSR starts.

When an error occurs, the corresponding status LED

lights together with the error LED, which lights or blinks

to indicate the type of error.

For details, see “STATUS LED” (page 23).

E Error LED

Lights or blinks when an error occurs.

F REC LED

Lights when recording images.

G DVD/CD drive

Use this drive to write data from the NSR hard disks to

DVD and CD.

* For details on compatible media, refer to the “User’s

Guide” (PDF) on the supplied “NSR Series Manual, Tool

& Source Codes CD”.

H USB connector

Use this connector to connect a USB keyboard, mouse,

USB flash memory or the RM-NS10 remote control to

the NSR.

I Audio input connector*

Use this connector to input audio from a peripheral

audio device, such as a microphone.

J Audio output connectors (L and R)

Use these connectors to output audio to a peripheral

audio device.

K Video output connector

Use this connector to output video to a peripheral video

device, such as a VCR.

The displayed images are the same as those for monitor

connector 1.

L Monitor connector 1

Use this connector to connect a monitor.

M CompactFlash card slot

Use this slot to save configuration data from the NSR

hard disks to a CompactFlash card.

POWER 1 2 3NETWORK 1 2 3 4HDD 1 2 3 4 ERRORSTATUS REC

123 4 5 6

708q

a

9q

s

q

d

q

f

q

g

Features and Functions

8

N Lock

Use this in conjunction with the supplied front panel key

to lock the front bezel. When the front bezel is locked,

you cannot pull out the front bezel. Also, do not lock the

front bezel when the front bezel is pulled out. You can

distinguish the locked position from the unlocked

position by looking at the lock, as illustrated below.

O Vent holes

These openings allow air to flow from the front of the

NSR to the rear.

Do not block the vent holes, allow dust to accumulate in

the inner mesh of the vent holes, or obstruct the airflow

in any way. Obstructing the airflow allows heat to build

up inside the NSR and may result in fire or damage.

* This feature is not currently supported.

NSR-25

A Power LED

Alternates between green and amber lights when the unit

is starting up.

Lights green when startup is complete.

Lights amber when it is on standby.

B Network LED

Lights green when there is activity at the corresponding

LAN connector at the rear of the NSR.

C HDD LED

Blinks green when the internal hard disks are accessed.

Lights amber when an error occurs with a hard disk.

D Status LED (1 to 4)

Lights in sequence (1, 2, 3, 4) when the NSR starts.

When an error occurs, the corresponding status LED

lights together with the error LED, which lights or blinks

to indicate the type of error.

For details, see “STATUS LED” (page 23).

E Error LED

Lights or blinks when an error occurs.

F REC LED

Lights when recording images.

G Combo drive

Use this drive to write data from the NSR hard disks to

CD.

H Lock

Use this in conjunction with the supplied front panel key

to lock the front bezel. When the front bezel is locked,

you cannot pull out the front bezel. Also, do not lock the

front bezel when the front bezel is pulled out. You can

distinguish the locked position from the unlocked

position by looking at the lock, as illustrated below.

I Vent holes

These openings allow air to flow from the front of the

NSR to the rear.

Do not block the vent holes, allow dust to accumulate in

the inner mesh of the vent holes, or obstruct the airflow

in any way. Obstructing the airflow allows heat to build

up inside the NSR and may result in fire or damage.

The front bezel is

locked

The front bezel is

unlocked

POWER 1 2 3NETWORK 1 2 3 4HDD 1 2 3 4 ERRORSTATUS REC

123 4 5 6

789

The front bezel is

locked

The front bezel is

unlocked

Features and Functions

9

Rear

NSR-100/50

A Fan

Take care not to obstruct the fan grille. If the grille is

obstructed, heat may build up in the unit, leading to

damage and/or fire.

B Power switch

Press the switch in the a position to turn on the unit.

C Video output connector

Use this connector to output video to a peripheral video

device, such as a VCR.

The displayed images are the same as those for monitor

connector 1.

D S-video output connector

Use this connector to output video to a peripheral video

device equipped with an S-video connector.

The displayed images are the same as those for monitor

connector 1.

E Serial connector (RS-232C)

Use this connector to connect the control line of the

uninterruptible power supply (UPS).

F Sensor input connector

Use this connector to connect the sensor input lines.

For connection details and wiring diagrams for sensor

inputs, see “I/O Port” (page 27).

G Alarm output connector

Use this connector to connect the alarm output lines.

For connection details and a wiring diagram for alarm

output, see “I/O Port” (page 27).

H Audio input connector*

Use this connector to input audio from a peripheral

audio device, such as a microphone.

I SCSI connector*

Use this connector to connect a peripheral SCSI device.

J USB connector

Use this connector to connect a USB keyboard, mouse,

USB flash memory or the RM-NS10 remote control to

the NSR.

K LAN connectors (1 to 3)

Use these connectors to connect 10 Base-T, 100 Base-

TX, or 1000 Base-T network cables to the NSR.

LAN1: Network cameras

LAN2: Remote Clients

LAN3: External storage devices**

L Monitor connectors (1 and 2)

Use these connectors to connect a monitor.

M Audio output connectors (L and R)

Use these connectors to output audio to a peripheral

audio device.

N Power supply connector

Use this connector to connect the power cord.

* This feature is not currently supported.

** The external storage device is not supported depending on

the software version. Consult your dealer.

231 654 7 8

9q

s

0q

a

q

d

q

f

Features and Functions

10

NSR-25

A Fan

Take care not to obstruct the fan grille. If the grille is

obstructed, heat may build up in the unit, leading to

damage and/or fire.

B Power switch

Press the switch in the a position to turn on the unit.

C Serial connector (RS-232C)

Use this connector to connect the control line of the

uninterruptible power supply (UPS).

D Sensor input connector

Use this connector to connect the sensor input lines.

For connection details and wiring diagrams for sensor

inputs, see “I/O Port” (page 27).

E Alarm output connector

Use this connector to connect the alarm output lines.

For connection details and a wiring diagram for alarm

output, see “I/O Port” (page 27).

F Audio input connector*

Use this connector to input audio from a peripheral

audio device, such as a microphone.

G USB connector

Use this connector to connect a USB keyboard, mouse,

USB flash memory or the RM-NS10 remote control to

the NSR.

H LAN connectors

Use these connectors to connect 10 Base-T, 100 Base-

TX, or 1000 Base-T network cables to the NSR.

I Monitor connectors (1 and 2)

Use these connectors to connect a monitor.

J Audio output connectors (L and R)

Use these connectors to output audio to a peripheral

audio device.

K Power supply connector

Use this connector to connect the power cord.

* This feature is not currently supported.

21 43 5 6

7890q

a

Installation

11

Installation

When you are sure that the site chosen to set up the

NSR provides appropriate space and strength to

support the recorder, connect the AC power cord.

The NSR-100 weighs approx. 14 kg (31.1 lb.), the

NSR-50 weighs approx. 12 kg (26.7 lb.), and NSR-25

weighs approx. 11 kg (24.2 lb.). The NSR has the

following dimensions.

Top

When the front bezel is closed

When the front bezel is opened

You can set up the NSR in a rack mount or on a flat

surface. If you plan to set it up on a flat surface, you must

attach the supplied rubber feet to the bottom of the

chassis.

Installation Without a Rack

Attach the provided rubber feet to the recorder.

Place the recorder upright so that the bottom surface is

visible. Then affix the adhesive surfaces of the rubber

feet on the bottom of the recorder as illustrated below.

16.9 in.

(430 mm)

16.4 in.

(417 mm)

3.4 in.

(87 mm)

16.9 in. (430 mm)

16.4 in. (417 mm)

14.8 in. (377 mm)1.6 in. (40 mm)

19.4 in. (494 mm)

4.6 in.

(117 mm)

4.2 in.

(106 mm)

14.8 in. (377 mm)

4.0 in.

(102 mm)

18.9 in. (479 mm)

4.8 in.

(123 mm)

Rubber

foot

Remove

the film

Bottom of the unit

Installation

12

Rack Mount Installation

Install the NSR in a rack using the optional rack

mounting kit (sold separately).

Warning

• Do not use a rack mounting kit other than the optional

mounting kit (sold separately) for the NSR, as doing

so is dangerous and may result in fire, shock, or injury.

• If you mount the NSR in a rack, make sure not to place

heavy object on it.

• Before mounting the NSR in a rack, we recommend

that you mark its intended position in the rack with a

felt-tip pen. Mounting the NSR in the rack otherwise

than horizontally could result in malfunctions.

• To order a rack mounting kit, contact your retailer.

Pulling Out the Inner Rails

Pull out the inner rails from the rail assemblies.

1

Pull out the inner rail from one of the rail

assemblies as far as it can go.

2

Turn the rail assembly over. As you pull the green

tab outward to release the lock, pull the inner rail all

the way out.

3

Repeat the same procedure with the other rail

assembly to pull out its inner rail.

Note

The inner rail will be installed on the NSR, while

the rail assembly will be installed on the rack.

Preparing the NSR

Use the supplied fasteners and screws to install the inner

rail on the NSR.

1

Use the supplied flat head screws to attach the

mounting ears to the front of the side panel.

2

Use the remaining supplied round head screws to

install the rails to the NSR, as illustrated.

Caution

Using screws other than the supplied screws may

damage the unit. Be sure to use the supplied screws

to install the rails.

Preparing the Rack

Install the rails on the rack.

1

Determine where you want to install the rails on the

rack.

We recommend marking this position with a

marker or felt tip pen.

Caution

Rails installed at different heights could result in

NSR malfunctions.

Back of rail assembly

Inner rail

Rail assembly

Green tab

Mounting ear

Flat head

screws

Rail

Round head

screws

Green tab

Installation

13

2

Install the rails on the rack.

(1) Adjust the length of the rails to match the length

of your rack.

(2) Use the supplied truss screws and washers to

secure both ends of the rails to the rack.

Mounting the NSR on the Rack

Insert the NSR into the rack, and then secure it.

Caution

At least two people are needed in order to handle the unit

to prevent personal injury.

1

Pull the sliding rails from the rail assemblies.

2

Lift the NSR, fit the inner rails into the slide rail

grooves (white), and then slide the assembly until it

stops.

3

As you pull the green tab inward to release the lock,

slide the NSR as far as it can go.

Truss

screws

Washers

Inner rail

Green tab

Installation

14

4

Use the supplied round head screws to secure the

NSR to the rack.

* The remainder of this manual uses illustrations and screens

of the NSR-100/50.

Connecting a Monitor

Connect the monitor to the monitor1 connector on the

rear of the recorder.

Connecting the Keyboard, Mouse

and Remote Control Unit

(RM-NS10)

1

Connect the keyboard to the USB connector on the

rear (or front) of the recorder.

2

Connect the mouse or the remote control unit

(RM-NS10) to the USB connector.

Note

When using the NSR-25, only the two USB

connectors on the rear of the unit are available.

Connecting a keyboard and mouse makes setting up

for the first time easier.

Connecting the Power Cord

1

Connect the power cord to the power supply

connector at the rear of the NSR, and then connect

the other end to the power outlet.

2

Lift the power cord safety clip and snap it around

the power cord to prevent it from disconnecting.

Note

Before installing, carefully read “Important

Information About Safety” (page 3). When using

more than one NSR, also make sure to have

sufficient power capacity.

Connecting the Network Cable

Connect the network cable.

Connect the one end of the network cable to one of the

LAN connectors at the rear of the NSR. Connect the

other end to the network switch.

Round head

screw

1

To the power

outlet

Installation

15

Note

The default IP address for LAN port 1 is follows;

• LAN connector 1: 192.168.0.1

• LAN connector 2: 192.168.1.1

(only the NSR-100/50)

• LAN connector 3: 192.168.2.1

(only the NSR-100/50)

If you want to change the default IP address, refer to the

“User’s Guide” (PDF) on the supplied “NSR Series

Manual, Tool & Source Codes CD”.

Connecting a Network Camera

Use a network cable to connect LAN connector 1 to a

network switch, and then connect the desired network

camera to the network switch with another network

cable.

Connecting Other Devices

Using a CompactFlash Card (Only the

NSR-100/50)

Insert your CompactFlash card in the direction

illustrated. Make sure that you insert your card with the

label side facing up and in the direction of the arrow.

When ejecting a CompactFlash card, press the eject

button on the left of the card slot.

Caution

Be careful when ejecting a CompactFlash card, because

it may be expelled from the drive energetically.

Connecting an Uninterruptible Power

Supply

1

Connect the uninterruptible power source to the

power outlet.

2

Connect the NSR to the UPS with the supplied

power cord.

3

Connect the NSR to the UPS with the dedicated serial

cable to the serial connector on the rear of the NSR.

Connecting Remote Client

If a remote client is required, the supplied RealShot

Manager Controller software can be used.

RealShot Manager Controller runs on Windows

computers. For details on system requirements, refer to

the release notes accompanying the RealShot Manager

Controller install archive. Also, make sure to use the

RealShot Manager supplied with the NSR.

1

Use a network cable to connect LAN connector to

a network switch.

When using the NSR-100/50, connect to LAN

connector 2 on the unit.

2

Connect the network cable to a computer when

RealShot Manager Controller software is installed.

Notes

• For details on installation and other topics related to

the RealShot Manager Controller software, refer to the

supplied NSR Series Manual, Tool & Source Codes

CD.

• When using RealShot Manager as a remote controller

for the NSR, select [Controller] during installation of

RealShot Manager.

• The default connection port for the RealShot Manager

server function on the NSR unit is “8081”. The

connection port can be changed from the NSR.

• When using the NSR-100/50, use LAN connector 2 at

the rear of the NSR even if connecting it to the user

area of a network.

Network Camera

Network switch

POWER 1 23LAN 1 2 34HDD 1 2 3 4 ERRORSTATUS REC

Windows PC

Network switch

RealShot Manager

Controller software

(For the NSR-100/50)

Turn the Power On and Off / Initial Operations (Basic Initial Setup)

16

Turn the Power On and

Off

Turning On the Power

Press the power switch.

When startup is complete, the power indicator LED

lights green.

Notes

• Immediately (about 2 seconds) after the power is

turned on, the cooling fan makes a loud noise. This is

normal and not a sign that the unit needs to be

serviced.

• When the NSR starts for the first time, the Setup

Wizard starts automatically. For details about the

setting procedure, refer to the “User’s Guide” (PDF)

on the supplied “NSR Series Manual, Tool & Source

Codes CD”.

• If the NSR was previously shut down improperly,

startup may take longer than usual.

Turning Off the Power

1

Log on to the NSR, and click [System] at the top of

the window.

The System Menu screen appears.

2

Click [Shutdown].

A confirmation message appears.

3

Click [OK] to confirm.

The system shuts down, and then the unit shuts

down.

Initial Operations

(Basic Initial Setup)

Basic Configuration

1

Connect the USB keyboard and USB mouse to the

unit, and turn on the power.

The following screen appears, and a progress bar

for hardware startup appears.

Then the following screen appears, and a progress

bar for software startup appears.

The unit starts and the system settings screen

(Setup Wizard) appears.

2

Click [Next].

The [Select Language] screen appears.

Initial Operations (Basic Initial Setup)

17

3

Select the desired display language from the list,

and then click [Next].

The [EULA] screen appears.

4

Read the user license agreement, click [Accept],

and then click [Next].

The [Keyboard Layout] screen appears.

5

Select the type of USB keyboard connected to the

unit from the list, and then click [Next].

The [Time Zone] screen appears.

6

Select the desired time zone from the list, and then

click [Next].

* There is no option for enabling or disabling

summer time. If you select a time zone in which

time is adjusted for summer time, the time is

adjusted for summer time automatically.

The [Date and Time] screen appears.

7

Verify the date and time, and configure the correct

date and time if necessary, then click [Next].

The [General Network Setting] screen appears.

8

Perform the following steps to configure the

network settings.

(1) Enter an IP address for each server in the

[General Network Setting] screen, and click

[Next].

Primary DNS

Enter the primary DNS (Domain Name Server)

IP address.

When there is no primary DNS or one is not

necessary, do not enter an IP address.

Secondary DNS

Enter the secondary DNS IP address.

When there is no secondary DNS or one is not

necessary, do not enter an IP address.

Default Gateway

Enter the default gateway IP address.

When only the local network is used or

connection to other networks is not necessary,

do not enter an IP address.

The [Network Device #1] screen appears.

(2) Configure the [Network Device] settings for

each of the LAN ports.

When using the NSR-100/50, configure the

settings for each of the three LAN ports (LAN1,

LAN2, and LAN 3).

When using the NSR-25, configure the settings

for the single LAN port (LAN1).

Initial Operations (Basic Initial Setup)

18

Configure the settings according to the

operation environment, and click [Next] for

each of the settings screen.

Note

When using the NSR-100/50, connect the

following devices to each of the LAN ports.

LAN1: Network cameras

LAN2: Remote clients

LAN3: External storage devices (This may not

be supported depending on the software version.

For details, consult your dealer.)

When using a DHCP server to configure

address settings automatically

Select [DHCP].

When configuring addresses manually

(1) Select [Static].

(2) Enter the following information.

IP Address

Enter the desired IP address.

Caution

• Before you enter the desired IP address,

make sure that it is not already otherwise

used on the network. Entering an IP

address already in use may lead to erratic

operation of the unit, but no error

messages appear to indicate the fact.

• Because of IP address attribution rules,

setting an invalid address such as the ones

below is not allowed.

Example: 224.0.0.0 to 255.255.255.255

0.0.0.0

127.0.0.1, etc.

Netmask

Enter the subnet mask address.

Note

The default settings for network devices are

as follows.

IP Address: 192.168.[0/1/2]*.1

Netmask: 255.255.255.0

* The settings for each of the network

devices #1, #2, and #3 (only network

device #1 for the NSR-25).

The [Monitor Model] screen appears.

9

Perform screen size settings depending on each

monitor port, and then click [Next].

When two monitors are connected, clicking [Dual

Head] displays the second monitor configuration

screen.

Select the appropriate monitor type and resolution

(pixels) for your monitor.

Notes

• The default setting for monitors is as follows.

Generic LCD Display; LCD Panel 1600x1200;

31.5-90; 60

Resolution 1024x768

• Most monitors will operate with [Generic

Monitor], but you can select [Others] as required.

Caution

When configuring settings for the second monitor,

the second monitor must be connected when the

NSR restarts. Be sure to connect the second

monitor before finishing the configurations.

When using the NSR-100/50, the [Video Setting]

screen appears. Proceed to step 10.

When using the NSR-25, the [Host Name] screen

appears. Proceed to step 11.

Initial Operations (Basic Initial Setup)

19

10

Select the appropriate video format, depending on

your region, [NTSC] or [PAL], and then click

[Next].

* This screen only appears when using the

NSR-100/50.

The [Host Name] screen appears.

11

Perform settings for each item, and then click

[Next].

Host Name

Enter the host name.

Note

Use only alphanumeric characters, underscores (_),

and hyphens (-).

Domain Name

Enter the network domain name according to your

network.

Example: xxx.sony.co.jp

When you do not register the NSR to the DNS, you

do not need to change the default settings.

The [Summary] screen appears.

12

Confirm the settings and then click [Next].

The [Warning] screen appears.

13

Click [Finish].

The NSR restarts automatically.

Camera IP Address Configuration

and Registration to NSR

After restarting, the logon screen appears.

Next, configure the IP addresses for cameras and

register them to the NSR.

1

Type your user name and password, and then click

[Log on].

Default User Name: admin

Default Password: admin

The Camera screen appears in the Configuration

window.

2

Click [Camera IP Setup].

If the IP addresses for the cameras have already

been set, click [Register All] and proceed to Step 5.

The Camera IP Setup window appears.

Initial Operations (Basic Initial Setup)

20

3

Perform the following settings.

In the Camera IP Setup window, you can search for

cameras on the same network by MAC address and

configure their IP addresses all at once.

(1) Select the network to search in the field labeled

“1. Select Network Device for IP Setup.”

Normally, Network 1 is selected as the camera

network, and a list of the cameras found appears

in the “Found Camera List.” The check boxes of

all found cameras are selected.

(2) Enter the following information in the field

labeled “2. Set Camera network setting.”

• The user name and password of the camera

you are configuring settings for.

• The range of IP addresses on the same

network (default: 0 to 254) for which to

perform automatic assignment.

• The http port number (default: 80) for

communicating with cameras.

* If there is a fixed range of IP addresses that

can be assigned to cameras, make sure to

specify the correct range.

(3) Click [Set].

The information you entered is reflected in the

“Found Camera List.”

IP addresses are assigned within the specified

range. Because the list does not expand to

compensate if there are not enough IP

addresses, make sure the list is set correctly by

directly changing addresses in the list as needed.

At this stage, the settings have not yet been

applied to the camera.

(4) Click [Apply].

This configures the camera settings using the

information developed in the list.

It takes a few moments for the settings to

complete.

4

When the settings for each camera are complete,

click [Register All].

The Register Cameras window appears.

5

Perform the following settings.

In the Register Cameras window, a list of cameras

that have not been registered to the NSR appears

with the check box for each selected.

(1) Verify the number of cameras selected for

registration in the column labeled “Cameras to

be registered”, and confirm the user name and

password for each camera.

Note

The user name and password for the cameras are

not set by default. You can set the user name and

password for the selected cameras all at once

under “Register selected Cameras for NSR”.

(2) Click [Register].

The selected cameras are registered to the NSR.

* By clicking [Camera IP Setup], you can also

return to the previous Camera IP Setup

window.

6

When registration is complete, click [Close].

The Configuration window returns to the Camera

screen. The registered cameras are listed.

7

If necessary, configure the individual settings for

each camera.

For details about settings, refer to the supplied

user’s guide.

ページが読み込まれています...

Sony Security Camera Security Camera ユーザーマニュアル

このマニュアルも適しています

Sony Security Camera Security Camera ユーザーマニュアル

他の言語で

関連論文

その他のドキュメント