2. SKYDANCE
  3. DH
DH

SKYDANCE DH ユーザーマニュアル

  • このDALI ACスイッチDT7/2 DHのユーザーマニュアルを読み終えました。デバイスの機能、仕様、設定方法などについてご質問にお答えできます。例えば、最大出力電流、DALIアドレスの設定方法、動作温度範囲、保証期間などについてご質問ください。
  • 最大出力電流は？
    DALIアドレスの設定方法は？
    動作温度範囲は？
    保証期間は？
1
User Manual Ver 2.0.0
Features
Technical Parameters
Input and Output
Gross weight 0.140kg
Operation temperature
Case temperature (Max.)
Environment
IP20
IP rating
Ta: -30
O
C ~ +55
O
C
Tc:
+70
O
C
Mechanical Structures and Installations
187.00 mm
46.00 mm
22.00 mm
Size
Package
L190x W48 x H25mm
Warranty
5 years
Warranty
Model No.: DH
DALI AC Switch
● DALI control power on/off to cater for unwanted dimming lighting system,
two DALI address, two channel output, AC input and AC output.
● , in accordance with DALI standard protocol IEC 62386-101,DALI-2 certified
102, 208 and in compliance with DALI products from other international
incorporation.
● DALI address can be manually assigned and shown in digital display or
automatically assigned by DALI master.
● The switching thresholds of the relay can be set on the DALI bus.
● Zero cross switching function, 2 independently output channels AC switch.
● To switch two LED lamps, traditional incandescent and halogen lights.
DT7/2 DALI address/2 Channel AC output/Numeric display
LVD
Wiring Diagram
Note:
If output connect with capacitive or inductive load, the maximum output current only up to 5A.
If output connect with resistive load, the maximum output current may up to 8A.
DALI
Master
N
L
AC 100-240V
SIGNA L INPUT
Da2
Da1
Da2
Da1
N
N
L1
L2
0-6 0-9
L
N
SIGNA L INPUT
AC IN PUT
AC OU TPUT 1
AC OU TPUT 2
SIGNA L INPUT
Da2
Da1
Da2
Da1
N
N
L1
L2
0-6 0-9
L
N
SIGNA L INPUT
AC IN PUT
AC OU TPUT 1
AC OU TPUT 2
Please carefully ensure all wire connections and polarities are correct and secure before applying power, otherwise this controller will be damaged.
Caution:
LED light
Two groups of DALI signal input
DALI bus no need distinguish
plus-minus polarity
Setting key Digital display
SIGNA L INPUT
Da2
Da1
Da2
Da1
N
N
L1
L2
0-6 0-9
L
N
SIGNA L INPUT
AC INP UT
AC OUT PUT 1
AC OUT PUT 2
AC N
AC N
AC L Input
AC L Output 1
AC N
AC L Output 2
N
L
AC 100-240V
LED light
2CH, 5A Max
AC100-240V
AC100-240V
2*(500-1200)W
Output current
Input voltage
Output voltage
Output power
2
User Manual Ver 2.0.0
DALI address can also be assigned by DALI Master controller automatically.
Please refer to user manuals of compatible DALI Masters for specic operations.
The digital display will show “AU” When the DALI master is assigning address.
After address is assigned, the digital display will show the start DALI address”xx”, xx is from 00 to 63.
DALI address assigned by DALI masters
● Long press any of the two buttons for 2s, prepare for set the start DALI address, digital display start ashes.
● Short press left button to set “tens” position and right button to set “units” position.
● The address can be set from 00~62-FF. no DALI address is assigned for the dimmer, digital display shows “FF”.
● Address assignments are sequential. If the set address value is 01, the CH1 address value is 01, and the CH2 address value is 02,
The display shows the CH1 address value.
● Long press any of the two buttons for 2s or timeout 10s, quit start DALI address setting, digital display stop ashes.
Set DALI Address via buttons
● Long press two buttons at the same time for 2s, Toggle Relay Switch: On(”On”) and Off(”OF”).
● Enter the default setting to on(”On”), then short press the left setting button to turn on(”On”), short press the right setting button to turn off(”OF”).
● Long press any of the two buttons for 2s or timeout 10s, quit Relay switch setting.
Operation
Relay switch setting
1
版本2.0.0
LVD
技术参数
⽑重
机械结构和安装
187.00 mm
46.00 mm
22.00 mm
尺⼨
质保
景晴光电
型号:DH
DALIAC开关
DT7/2DALI地址/2通道输出/数字显⽰
特点
● DALIAC开关，两个DALI地址，两个通道输出，AC输⼊和AC输出。
● 认证，符合DALI标准协议IEC 62386-101，102，208，兼容其他品牌的DALI产品。DALI-2
● DALI地址可以⼿动分配并数字显⽰，也可以由DALI主机⾃动分配。
● 通过DAIL总线设置继电器开关阈值。
● AC过零检测功能。
● LED灯，传统⽩炽灯和⻧素灯 。⽤于 的开关
SIGN AL INPUT
Da2
Da1
Da2
Da1
N
N
L1
L2
0-6 0-9
L
N
SIGN AL INPUT
AC IN PUT
AC OU TPUT 1
AC OU TPUT 2
AC N输⼊
AC N 输出1
AC N 输出2
ACL输⼊
ACL输出1
ACL输出2
两组DALI信号输⼊，
⽆需区分正负极性
设置键 数字显⽰
接线图
警告:在上电之前，请确保所有电线连接和极性正确和牢靠，否则可能损坏调光器。
注意：当连接感性或容性负载时，最⼤输出电流为5A。
当连接纯电阻负载时，最⼤输出电流为8A。
DALI
Master
N
L
AC 100-240V
SIGNA L INPUT
Da2
Da1
Da2
Da1
N
N
L1
L2
0-6 0-9
L
N
SIGNA L INPUT
AC IN PUT
AC OU TPUT 1
AC OU TPUT 2
SIGNA L INPUT
Da2
Da1
Da2
Da1
N
N
L1
L2
0-6 0-9
L
N
SIGNA L INPUT
AC IN PUT
AC OU TPUT 1
AC OU TPUT 2
LED灯
N
L
AC 100-240V
LED灯
0.140kg
IP20
Ta: -30
O
C ~ +55
O
C
Tc:
+70
O
C
190x 48 x 25mm(⻓x宽x⾼）
5 年
2CH, 5A Max
AC100-240V
AC100-240V
2*(500-1200)W
输出电流
输⼊电压
输出电压
输出功率
输⼊和输出 环境
⼯作温度
外壳最⾼温度
IP等级 质保
包装
2
版本2.0.0
⼴州景晴光电科技有限公司GuangzhouSkyacneCo.,Ltdwww.iskydance.cn
本资料上的内容均经过认真核对，如有任何印刷错漏或内容上的误解，本公司保留最终解释权。
产品若有技术改进，会编⼊新版说明书中，恕不另⾏通知。
通过按键设置DAIL地址
● 同时⻓按两个设置键2秒,进⼊继电器开关设置:开“( On”)和关“( OF”).
● 默认设置继电器开关为开（“On”）,短按左键开启灯光，短按右键关闭灯光。
● ⻓按任⼀按设置键或超时10秒，退出继电器开关设置。
操作
继电器开关设置
DALI主控分配地址
DALI地址可由DALI主控⾃动分配，请参考DALI主控⽤⼾⼿册。
当DALI主控在分配地址时，数字显⽰“AU”。
地址分配完毕，数字显⽰DALI地址”xx”,xx是00到63。
● ⻓按任⼀设置键2秒，准备设置DALI地址，数码管闪烁。
● 短按左键设置⼗位地址值，短按右键设置个位地址值。
● 地址值可设置为00~62。当调光器未分配地址时，数字显⽰“FF”。
● 地址分配是顺序的。如果设置地址值为01，通道1的地址就是01，通道2的地址就是02，
数码管显⽰通道1的地址。
● ⻓按任⼀设置键2秒或10秒未操作，退出地址设置状态，数字显⽰停⽌闪烁。
/