Technical Parameters
1
User Manual Ver 1.0.0
Features
Input and Output
Operation temperature
Environment
Ta: -30
O
C ~ +55
O
C
Case temperature (Max.)
IP rating IP20
Ta: +75
O
C
Warranty
5 years
Warranty
Output current
Input voltage
Output voltage Gross weight
Size
Package
L60x W60 x H40mm
0.061kg
Model No.: DA-P
DALI Push Dimmer
Push Dim/Address programmability/Dim speed adjustable/Memory function
● Small Dimmer for DALI Drivers or Ballasts.
● Unidirectional and broadcasting communication.
● Control by conventional push-button, with or without memory:
Short press: turn on /off light.
Long press: dimming up/down.
● Dimming speed adjustable by rotary knob.
Max 0.05A
100-240VAC
100-240VAC
DAIL bus output 100mA max
Mechanical Structures and Installations
AC input
DAIL signal +
52.00 mm
52.00 mm
27.00 mm
Memory Setting button
DAIL signal -
Dimming speed adjust.
10x(0~9) for setting tens position
Memory status indicator
Rotary switches for setting DALI address,
the number equals to tens position plus units position
1x(0~9) for setting units position
AC push-button input
Wiring Diagram
Please carefully ensure all wire connections and polarities are correct and secure before applying power, otherwise this controller will be damaged.
Caution:
Push-button
L
N
100-240V~50/60Hz
L
N
DA+
DA-
DALI
Ballast or
Driver
L
N
DA+
DA-
DALI
Ballast or
Driver
Push-button function
● Short press:
Turn on / off light.
● Long press :
Dimming up/down
• DO NOT install with power applied to device.
• DO NOT expose the device to moisture.
Safety & Warnings
DALI address setting
1. Address value = Left rotary switch value × 10 + right rotary switch value.
For example : Left rotary switch value is 5, right rotary switch value is 4, Address value = 5 x 10 + 4 = 54.
2. Unicast mode : Address value 0-63 corresponds to DALI addresses 00-63.
Group mode : Address values 70-85 correspond to DALI groupings 0-15.
Broadcast mode : Left rotary switch value is 9.
PUSH dimming speed setting
1.The closer the arrow is to "+", the faster the PUSH dimming speed will be.
2. The closer the arrow is to "-", the slower the PUSH dimming speed will be.
Memory function setting
Short press the "SET" button to switch the memory function.
1. Without memory: LED indicator is red, PUSH dimming and then power on again, light returns to maximum brightness.
2. With memory: LED indicator is green, PUSH dimming and then power on again, light restores the last brightness.
Factory default: Without memory.
2
User Manual Ver 1.0.0
技术参数
特点
输⼊和输出
⼯作温度
环境
外壳最⾼温度
IP等级 质保
5年
质保
输出电流
输⼊电压
输出电压 ⽑重
尺⼨
包装
60x 60 x 40mm(⻓x宽x⾼)
0.061kg
型号:DA-P
DALI⾃复位开关调光器
⾃复位开关调光/地址可编辑/调光速度可调/记忆功能
●⽤于DALI驱动器或镇流器的调光器。
●单播和⼴播通信。
●通过 按键控制灯光，带或不带亮度记忆功能:⾃复位开关
短按:打开/关闭灯光；
⻓按:调亮/调暗亮度。
●调光速度可通过旋钮调节。
Max 0.05A
100-240VAC
100-240VAC
DAIL总线输出 100mA max
机械结构和安装
AC输⼊
DAIL信号+
52.00 mm
52.00 mm
27.00 mm
记忆设置按键
DAIL信号-
调光速度可调
10x(0~9)⽤于设置⼗位地址
记忆状态指⽰灯
⽤于设置DALI地址的旋转编码开关
1x(0~9)⽤于设置个位地址
AC⾃复位开关输⼊
接线图
在上电之前，请确保所有电线连接和极性正确和牢靠，否则可能损坏调光器。
警告:
⾃复位开关
L
N
100-240V~50/60Hz
L
N
DA+
DA-
DALI
镇流器或
驱动器
L
N
DA+
DA-
DALI
镇流器或
驱动器
Ta: -30
O
C ~ +55
O
C
IP20
Ta: +75
O
C
1
版本1.0.0
景晴光电
⾃复位开关功能
● 短按:
打开/关闭灯光。
●⻓按:
调亮/调暗灯光。
● 不要带电安装调光器。
● 不要将调光器安装在潮湿环境。
安全和警告
DALI地址设置
1.地址值=左侧旋转开关值×10+右侧旋转开关值。
例如：左侧旋转开关值为5，右侧旋转开关值为4，地址值=5x10+4=54。
2.单播模式：地址值0-63，对应DALI地址00-63。
组模式：地址值70-85，对应于DALI组地址0-15。
⼴播模式：左侧旋转开关值为9。
⾃复位开关调光速度设置
1.箭头越靠近“+”，⾃复位开关调光速度越快。
2.箭头越靠近“-”，⾃复位开关调光速度越慢。
记忆功能设置
短按“SET”键切换记忆功能。
1.⽆记忆功能：指⽰灯为红⾊，⻓按⾃复位开关调节亮度后，再重新上电，灯光亮度恢复到最⼤亮度。
2.带记忆功能：指⽰灯为绿⾊，⻓按⾃复位开关调节亮度后，再重新上电，灯光亮度恢复到调节的亮度。
出⼚默认⽆亮度记忆功能。
2
版本1.0.0
⼴州景晴光电科技有限公司GuangzhouSkyacneCo.,Ltdwww.iskydance.cn
本资料上的内容均经过认真核对，如有任何印刷错漏或内容上的误解，本公司保留最终解释权。
产品若有技术改进，会编⼊新版说明书中，恕不另⾏通知。
-
1
-
2
-
3
-
4
