Copyright © 2011 ICP DAS Co., Ltd. All Rights Reserved. E-mail: service@icpdas.com
WISE-580x Quick Start Guide
1
Quick Start Guide for
WISE-580x Series
June 2011, Version 1.0
Thank you for purchasing WISE-580x – the Intelligent Data Logger PAC controller
for remote monitoring and control application. This Quick Start Guide will provide
you with minimum information to get started with WISE-580x. It is intended for use
only as a quick reference. For more detailed information and procedures, please
refer to the full user manual on the CD included in this package.
In addition to this guide, the package includes the following items:
WISE-580x
Series Module
Software
Utility CD
2G microSD
card
RS-232 cable
(CA-0910)
Screw Driver
(1C016)
WISE-580x User Manual
CD:\WISE-580x\document\User Manual\
http://ftp.icpdas.com/pub/cd/wise_cd/wise-580x/document/user manual/
WISE Website
http://wise.icpdas.com/index.html
ICP DAS Website
http://www.icpdas.com/
Copyright © 2011 ICP DAS Co., Ltd. All Rights Reserved. E-mail: service@icpdas.com
WISE-580x Quick Start Guide
2
1
--------------------------------------------
Configuring Boot Mode
Make sure the “Lock“ switch placed in the “OFF”
position, and the “Init’ switch placed in the “OFF”
position.
2
---------------------------------------------------------------------
Connecting to PC, Network and Power
The WISE-580x is equipped with an RJ-45 Ethernet port for connection to an
Ethernet hub/switch and PC. You can also link directly the WISE-580x to PC with an
Ethernet cable.
WISE-580x
+Vs
+
Copyright © 2011 ICP DAS Co., Ltd. All Rights Reserved. E-mail: service@icpdas.com
WISE-580x Quick Start Guide
3
3
-----------------------------------------------------
Installing the MiniOS7 Utility
Step 1: Get the MiniOS7 Utility
The MiniOS7 Utility can be obtained from companion CD or our FTP site:
CD:\Tools\MiniOS7 Utility\
ftp://ftp.icpdas.com/pub/cd/8000cd/napdos/minios7/utility/minios7_utility/
Please download version v3.2.4 or later.
Step 2: Follow the prompts to complete the installation
After the installation has been completed,
there will be a new short-cut for MiniOS7
Utility on the desktop.
4
-------------------------------------------------------------------------
Using MiniOS7 Utility to Assign a New IP
The WISE-580x is an Ethernet device, which comes with a default IP address,
therefore, you must first assign a new IP address to the WISE-580x.
The factory default IP settings are as follows:
Item
Default
IP Address
192.168.255.1
Subnet Mask
255.255.0.0
Gateway
192.168.0.1
MiniOS7 Utility Ver 3.24
Copyright © 2011 ICP DAS Co., Ltd. All Rights Reserved. E-mail: service@icpdas.com
WISE-580x Quick Start Guide
4
Step 1: Run the MiniOS7 Utility
Double-click the MiniOS7 Utility shortcut on your
desktop.
Step 2: Press “F12” or choose “Search” from the “Connection” menu
After pressing F12 or choosing “Search” from “Connection” menu, the MiniOS7
Scan dialog will appear, that will display a list of all the MiniOS7 modules on your
network.
See the status tip, waiting
for the search to be done.
Copyright © 2011 ICP DAS Co., Ltd. All Rights Reserved. E-mail: service@icpdas.com
WISE-580x Quick Start Guide
5
Step 3: Choose the module name and then choose “IP setting” from the
toolbar
Choose the module name for fields in the list, and then choose IP setting from the
toolbar.
Step 4: Assign a new IP address and then choose “Set” button
Step 5: Choose “Yes” button &
Reboot WISE-580x
After completing the settings, press the Yes
button in the Confirm dialog box to exit the
procedure, then reboot WISE-580x..
Copyright © 2011 ICP DAS Co., Ltd. All Rights Reserved. E-mail: service@icpdas.com
WISE-580x Quick Start Guide
6
5
----------------------------------------------------------------------------------
Go to WISE-580x Web Site to edit Control Logic
Please follow the steps below to implement IF-THEN-ELSE control logic on
controllers:
Step 1: Open a browser, and type in the URL address of the WISE-580x
Open a browser (recommended using Internet Explorer, new version is better). Type in
the URL address of the WISE-580x module in the address bar. Make sure the IP
address is accurate.
Step2: Get on the WISE-580x web site
Get on the WISE-580x web site.
Implement the control logic
configuration in the order (Basic
SettingAdvanced SettingRule
SettingDownload to Module), then
complete the IF-THEN-ELSE rule
editing.
.
Step 3: For more detail information, please refer to WISE User Manual
WISE-580x 快速安裝指南
1
WISE-580x 系列快速安裝指南
June 2011, Version 1.0
歡迎使用 WISE-580x 快速安裝指南
感謝您購買 WISE-580x系列控制器：多功能智慧型資料記錄(Data Logger)
PAC控制器。本『快速安裝指南』提供 WISE-580x系列安裝入門所需資訊, 如
需更詳細的安裝及使用說明, 請參閱更完整的使用手冊。
產品內容
除了本『快速安裝指南』外, 此產品內容還包括以下配件:
技術支援
WISE-580x User Manual
CD:\WISE-580x\document\User Manual\
http://ftp.icpdas.com/pub/cd/wise_cd/wise-580x/document/user manual/
WISE Website
http://wise.icpdas.com/big5/index.html
ICP DAS Website
http://www.icpdas.com/
WISE-580x
模組
軟體工具光碟
2G microSD
記憶卡
RS-232 纜線
(CA-0910)
螺絲起子
(1C016)
WISE-580x 快速安裝指南
2
1
--------------------------------------------
檢視啟動模式
確認指撥開關 Lock 的位置在 ”OFF”，Init
的位置在“OFF”。
2
---------------------------------------------
連接主機、網路及電源
WISE-580x 系列配有標準的網路接口 RJ-45，可透過網路集線器/交換器與 PC
連接, 也可直接連到 PC 的網路接口。
WISE-580x
+Vs
+
WISE-580x 快速安裝指南
3
3
---------------------------------------
安裝
MiniOS7 Utility
步驟一: 取得 MiniOS7 Utility
MiniOS7 Utility 可取自隨附的光碟或 FTP:
CD:\Tools\MiniOS7 Utility\
ftp://ftp.icpdas.com/pub/cd/8000cd/napdos/minios7/utility/minios7_utility/
請下載 v3.2.4 以後的版本。
步驟二: 按照命令提示完成安裝
安裝完成後, 桌面上將會出現
MiniOS7 Utility 的捷徑圖示
4
-----------------------------------------------------------
啟動
MiniOS7 Utility
設定
IP
位址
WISE-580x 系列模組在出廠時會統一預設網路設定值，使用者可以依照下列
步驟自行變更網路設定。WISE 模組的網路出廠預設值:
項目
預設值
IP 位址
192.168.255.1
子網路遮罩 (subnet mask)
255.255.0.0
通訊閘 (gateway)
192.168.0.1
MiniOS7 Utility Ver 3.24
WISE-580x 快速安裝指南
4
步驟一: 啟動 MiniOS7 Utility
雙擊MiniOS7 Utility
桌面捷徑
步驟二: 選取鍵盤 “F12” 或於 “Connection” 選單中選取 “Search”
選取鍵盤 F12 或於 Connection 選單中選取 Search 後, 會出現 MiniOS7 Scan
對話視窗顯示網路上已啟動的 MiniOS7 模組
確認狀態欄上顯示模組搜尋
完畢(Search Done).
WISE-580x 快速安裝指南
5
步驟三: 選取模組名稱後移到工具列選取 “IP setting”
於清單上選取模組名稱後移到工具列選取 IP setting
步驟四: 設定新 IP 後選取 “Set” 鈕
步驟五: 選取 “Yes” 鈕後，請重新開
機 WISE-580x
完成設定後, 於 Confirm 對話視窗選
取 Yes 鈕結束程序。隨後請重新開機
WISE-580x。
WISE-580x 快速安裝指南
6
5
--------------------------------------------------------------
前往
WISE
規則設定網頁
使用者透過 WISE 控制器所提供的規則設定網頁，只需使用滑鼠點選設定，即可完
成控制器上工作邏輯的規劃。
步驟一: 開啟瀏覽器，填入 WISE 控制器 IP 作為瀏覽器的 URL 位址
開啟電腦上的瀏覽器(推薦使用 IE，新版瀏覽器尤佳)，輸入 WISE 控制器的 IP 作
為 URL 位址(如有重新設定 IP，請確認所輸入 IP 是否正確)。
步驟二: 進入 WISE 規則設定頁面
進入 WISE-580x 控制器所提
供的規則設定頁面後，僅需依
照首頁上的設定流程(基本設
定進階設定規則設定規
則下載)，即可完成 WISE 控制
器的邏輯規則編排。
步驟三: 設定流程中的細節，請參照 WISE 操作手冊
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
