Robert Bosch Power Tools GmbH
70538 Stuttgart
GERMANY
www.bosch-pt.com
1 609 92A 4J8 (2018.11) T / 50
en Original instructions
zh 正本使用明
zh 原始使用說明書
ko 사용 설명서 원본
th
id Petunjuk-Petunjuk untuk Penggunaan Orisinal
vi Bn gc hng dn s dng
fr Notice originale
ar
fa
1 609 92A 4J8
GBS 75 A Professional
2 |
English ...................................................Page 5
....................................................... 11
.................................................. 14
............................................... 17
...................................................... 21
Bahasa Indonesia..................................... Halaman 26
Ting Vit............................................... Trang 30
Français..................................................Page 35
.................................................. 40
.................................................. 45
1 609 92A 4J8 | (07.11.2018) Bosch Power Tools
| 3
GBS 75 A
(6)
(7)
(5)
(4)
(3)
(2) (1)
(1)
(8)
Bosch Power Tools 1 609 92A 4J8 | (07.11.2018)
4 |
(9)
(7)
(6)
(6)
(7)
(10)
(6)
(11)
(2)
(3) (12) (9)
(13)
(14)
A1 A2
A3 A4
BC
1 609 92A 4J8 | (07.11.2018) Bosch Power Tools
English | 5
English
Safety instructions
General Power Tool Safety Warnings
WARNING Read all safety warnings, instruc-
tions, illustrations and specifica-
tions provided with this power tool. Failure to follow all in-
structions listed below may result in electric shock, fire and/
or serious injury.
Save all warnings and instructions for future reference.
The term "power tool" in the warnings refers to your mains-
operated (corded) power tool or battery-operated (cord-
less) power tool.
Work area safety
uKeep work area clean and well lit. Cluttered or dark
areas invite accidents.
uDo not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases or
dust. Power tools create sparks which may ignite the dust
or fumes.
uKeep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
Electrical safety
uPower tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs with
earthed (grounded) power tools. Unmodified plugs and
matching outlets will reduce risk of electric shock.
uAvoid body contact with earthed or grounded sur-
faces, such as pipes, radiators, ranges and refrigerat-
ors. There is an increased risk of electric shock if your
body is earthed or grounded.
uDo not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of elec-
tric shock.
uDo not abuse the cord. Never use the cord for carry-
ing, pulling or unplugging the power tool. Keep cord
away from heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the risk of electric
shock.
uWhen operating a power tool outdoors, use an exten-
sion cord suitable for outdoor use. Use of a cord suit-
able for outdoor use reduces the risk of electric shock.
uIf operating a power tool in a damp location is un-
avoidable, use a residual current device (RCD) protec-
ted supply. Use of an RCD reduces the risk of electric
shock.
Personal safety
uStay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a
power tool while you are tired or under the influence
of drugs, alcohol or medication. A moment of inatten-
tion while operating power tools may result in serious per-
sonal injury.
uUse personal protective equipment. Always wear eye
protection. Protective equipment such as a dust mask,
non-skid safety shoes, hard hat or hearing protection
used for appropriate conditions will reduce personal in-
juries.
uPrevent unintentional starting. Ensure the switch is in
the off-position before connecting to power source
and/or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or en-
ergising power tools that have the switch on invites acci-
dents.
uRemove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal in-
jury.
uDo not overreach. Keep proper footing and balance at
all times. This enables better control of the power tool in
unexpected situations.
uDress properly. Do not wear loose clothing or jew-
ellery. Keep your hair and clothing away from moving
parts. Loose clothes, jewellery or long hair can be caught
in moving parts.
uIf devices are provided for the connection of dust ex-
traction and collection facilities, ensure these are con-
nected and properly used. Use of dust collection can re-
duce dust-related hazards.
uDo not let familiarity gained from frequent use of tools
allow you to become complacent and ignore tool
safety principles. A careless action can cause severe in-
jury within a fraction of a second.
Power tool use and care
uDo not force the power tool. Use the correct power
tool for your application. The correct power tool will do
the job better and safer at the rate for which it was de-
signed.
uDo not use the power tool if the switch does not turn it
on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
uDisconnect the plug from the power source and/or re-
move the battery pack, if detachable, from the power
tool before making any adjustments, changing ac-
cessories, or storing power tools. Such preventive
safety measures reduce the risk of starting the power tool
accidentally.
uStore idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
uMaintain power tools and accessories. Check for mis-
alignment or binding of moving parts, breakage of
parts and any other condition that may affect the
power tool’s operation. If damaged, have the power
tool repaired before use. Many accidents are caused by
poorly maintained power tools.
Bosch Power Tools 1 609 92A 4J8 | (07.11.2018)
6 | English
uKeep cutting tools sharp and clean. Properly main-
tained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
uUse the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into ac-
count the working conditions and the work to be per-
formed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
uKeep handles and grasping surfaces dry, clean and
free from oil and grease. Slippery handles and grasping
surfaces do not allow for safe handling and control of the
tool in unexpected situations.
Service
uHave your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
Safety Warnings for Sander
uHold the power tool by insulated gripping surfaces,
because the sanding surface may contact its own
cord. Cutting a "live" wire may make exposed metal parts
of the power tool "live" and could give the operator an
electric shock.
uOnly use the power tool for dry sanding. Water entering
a power tool will increase the risk of electric shock.
uSwitch the power tool on before making contact with
the workpiece and only switch the power tool off after
you have removed it from the workpiece. The power
tool can move suddenly.
uNever touch the sanding belt while it is running. This
poses a risk of injury.
uWear protective gloves and never touch the sanding
belt while it is running. This poses a risk of injury.
uEnsure that no persons are at risk due to flying sparks.
Remove combustible materials from the surrounding
area. Flying sparks are created when sanding metals.
uDo not use any worn, torn or severely clogged sanding
belts. Damaged sanding belts can tear, fly off and injure
someone.
uWarning: Danger of fire! Avoid overheating the work-
piece and the sander. Always empty the dust collector
before taking a break from work. Sanding dust in the
dust bag, microfilter, paper bag (or in the filter bag or va-
cuum cleaner filter) can spontaneously combust under
certain conditions, for example if flying sparks are cre-
ated when sanding metals. This risk is increased if the
sanding dust is mixed with paint or polyurethane residue
or with other chemical substances and if the workpiece is
hot as a result of prolonged work.
uClean the air vents on your power tool regularly. The
motor’s fan will draw the dust inside the housing and ex-
cessive accumulation of powdered metal may cause elec-
trical hazards.
Products sold in GB only:
Your product is fitted with an BS 1363/A approved electric
plug with internal fuse (ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an au-
thorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
uSecure the workpiece. A workpiece clamped with
clamping devices or in a vice is held more secure than by
hand.
uAlways wait until the power tool has come to a com-
plete stop before placing it down. The application tool
can jam and cause you to lose control of the power tool.
uHold the power tool firmly with both hands and make
sure you have a stable footing. The power tool can be
more securely guided with both hands.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended Use
The power tool is intended for dry surface sanding of wood,
plastic, metal, filler and varnished surfaces with a high ma-
terial removal rate.
Product Features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) Auxiliary handle (insulated gripping surface)
(2) Sanding belt A)
(3) Clamping lever for sanding belt
(4) On/off switch
(5) Lock-on button for on/off switch
(6) Complete dust box (Microfilter system)
(7) Dust extraction adapter A)
(8) Handle (insulated gripping surface)
(9) Extraction outlet
(10) Locking lever for dust box
(11) Filter element (Microfilter system)
(12) Adjustment button for belt running
(13) Protective cap
(14) Dust channel
A) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
1 609 92A 4J8 | (07.11.2018) Bosch Power Tools
English | 7
Technical Data
Belt sander GBS 75 A
Article number 3 601 B74 0..
Rated power input W 710
Power output W 350
No-load belt speed m/min 300
Sanding belt length mm 533
Sanding belt width mm 75
Self-generated/external dust
extraction connection
●
Weight according to
EPTA-Procedure 01:2014
kg 3.2
Protection class / II
The specifications apply to a rated voltage [U] of 230 V. These spe-
cifications may vary at different voltages and in country-specific mod-
els.
Fitting
uPull the plug out of the socket before carrying out any
work on the power tool.
Dust/chip extraction
The dust from materials such as lead paint, some types of
wood, minerals and metal can be harmful to human health.
Touching or breathing in this dust can trigger allergic reac-
tions and/or cause respiratory illnesses in the user or in
people in the near vicinity.
Certain dusts, such as oak or beech dust, are classified as
carcinogenic, especially in conjunction with wood treatment
additives (chromate, wood preservative). Materials contain-
ing asbestos may only be machined by specialists.
– Use a dust extraction system that is suitable for the ma-
terial wherever possible.
– Provide good ventilation at the workplace.
– It is advisable to wear a P2 filter class breathing mask.
The regulations on the material being machined that apply in
the country of use must be observed.
uAvoid dust accumulation at the workplace. Dust can
easily ignite.
Self-generated Dust Extraction with Dust Box
(seefiguresA1−A4)
Place the dust box (6) on the extraction adapter (7) until it
engages. Attach the extraction adapter (7) to the extraction
outlet (9).
To empty the dust box (6), press the locking lever (10) on
the side of the dust box and pull off the dust box.
Before opening the dust box (6), knock the dust box against
a firm surface as shown in the figure to loosen the dust from
the filter element.
Take hold of the dust box (6) by the recessed grip, fold the
filter element (11) upwards out of the way and empty the
dust box. Use a soft brush to clean the flaps of the filter ele-
ment (11).
Note: The belt sander has a high material removal rate.
Therefore, to ensure optimum dust extraction, empty the
dust box (6) at regular intervals after every five minutes of
operation and clean the filter element (11) regularly.
External Dust Extraction
Fit a dust extraction hose onto the extraction outlet (9).
Connect the dust extraction hose to an extractor. You will
find an overview of connecting to various dust extractors at
the end of these operating instructions.
The dust extractor must be suitable for the material being
worked.
When extracting dry dust that is especially detrimental to
health or carcinogenic, use a special dust extractor.
Changing the Sanding Belt (see figure B)
– Swivel the clamping lever (3) all the way out. The sanding
belt (2) is now slack and can be removed.
– Fit the new sanding belt (2). Ensure that the arrow direc-
tions on the inner surface of the sanding belt and the
housing of the power tool match.
– Swivel the clamping lever (3) back to the starting posi-
tion.
– Lift up the power tool and switch it on. The belt running is
centred automatically when the tool is switched on and
during the sanding process.
Ensure that the sanding belt (2) does not grind against the
housing. Check the belt running regularly and, if necessary,
readjust it using the adjustment button (12).
Selecting a Sanding Belt
Different sanding belts are available, depending on the ma-
terial you are working with and the required surface removal
rate:
Grit
For processing all wood and wood-based
materials
40–240
For pre-sanding, e.g. of rough and
uneven beams and boards
Coarse 40, 60
For surface sanding and levelling of
slight irregularities
Medium 80, 100,
120
For finishing and fine sanding of hard
woods
Fine 180, 240
Operation
Start-up
uPay attention to the mains voltage. The voltage of the
power source must match the voltage specified on the
rating plate of the power tool. Power tools marked
with 230V can also be operated with 220V.
uProducts that are only sold in AUS and NZ: Use a resid-
ual current device (RCD) with a nominal residual current
of 30 mA or less.
Bosch Power Tools 1 609 92A 4J8 | (07.11.2018)
8 | English
Switching On and Off
uMake sure that you are able to press the On/Off switch
without releasing the handle.
To switch on the power tool, press and hold the on/off
switch (4).
To lock the on/off switch (4) press and hold it while also
pushing the lock-on button (5).
To switch off the power tool, release the on/off switch (4).
If the on/off switch (4) is locked, press the switch first and
then release it.
Practical advice
uPull the plug out of the socket before carrying out any
work on the power tool.
The material removal rate when sanding and the surface
quality are primarily determined by the choice of sanding
belt and the preselected belt speed. The higher the belt
speed, the higher the removal rate and the finer the sanded
surface becomes.
Only sanding belts in perfect condition achieve good sanding
performance and make the power tool last longer.
Apply as little contact pressure as possible while working in
order to increase the service life of the sanding belts. The
weight of the power tool alone is enough to ensure good
sanding performance. Excessively increasing the contact
pressure will not lead to increased sanding performance,
rather it will cause more severe wear of the power tool and of
the sanding belt.
Place the running power tool on the surface you wish to work
on. Work with moderate feed and carry out sanding in paral-
lel and overlapping with the sanding path. Sand with the
grain; sanding marks that run against the grain result in both-
ersome sanding effects.
Especially when sanding off paint residue, the residue could
merge together, resulting in smears on the workpiece sur-
face and the sanding belt. Therefore, do not work without
dust extraction.
A sanding belt that has been used to work on metal should
no longer be used to work on other materials.
Use only original Bosch-sanding accessories.
Only ever store sanding belts hanging up and do not fold
them as this makes them unusable.
The sanding frame (accessory) enables an even, adjustable
material removal rate while sanding large wooden surfaces.
Maintenance and Servicing
Maintenance and Cleaning
uPull the plug out of the socket before carrying out any
work on the power tool.
uTo ensure safe and efficient operation, always keep
the power tool and the ventilation slots clean.
Remove any adherent sanding dust using a brush.
In order to avoid safety hazards, if the power supply cord
needs to be replaced, this must be done by Bosch or by an
after-sales service centre that is authorised to repair Bosch
power tools.
Cleaning the Dust Channel (see figure C)
Remove the protective cover (13) from time to time and
clean the dust channel (14) to maintain optimal suction
power.
After-sales Service and Advice on Using
Products
Our after-sales service can answer questions concerning
product maintenance and repair, as well as spare parts. You
can find exploded drawings and information on spare parts
at: www.bosch-pt.com
The Bosch product use advice team will be happy to help you
with any questions about our products and their accessor-
ies.
In all correspondence and spare parts orders, please always
include the 10‑digit article number given on the type plate of
the product.
Cambodia
Robert Bosch (Cambodia) Co., Ltd
Unit 8BC, GT Tower, 08th Floor, Street 169,
Czechoslovakia Blvd, Sangkat Veal Vong
Khan 7 Makara, Phnom Penh
VAT TIN: 100 169 511
Tel.: +855 23 900 685
Tel.: +855 23 900 660
www.bosch.com.kh
People’s Republic of China
China Mainland
Bosch Power Tool (China) Co. Ltd.
Bosch Service Center
567, Bin Kang Road
Bin Kang District
Hangzhou, Zhejiang Province
China 310052
Tel.: (0571) 8887 5566 / 5588
Fax: (0571) 8887 6688 x 5566# / 5588#
E-mail: [email protected]
www.bosch-pt.com.cn
HK and Macau Special Administrative Regions
Robert Bosch Co. Ltd.
21st Floor, 625 King’s Road
North Point, Hong Kong
Customer Service Hotline: +852 2101 0235
Fax: +852 2590 9762
E-mail: [email protected]
www.bosch-pt.com.hk
India
Bosch Service Center
69, Habibullah Road, (next to PSBB School), T. Nagar
Chennai–600077
Phone: (044) 64561816
Bosch Service Center Rishyamook
85A, Panchkuin Road
1 609 92A 4J8 | (07.11.2018) Bosch Power Tools
English | 9
New Delhi–110001
Phone: (011) 43166190
Bosch Service Center 79,
Crystal Bldg., Dr. Annie Besant Road, Worli
Mumbai–400018
Phone: (022) 39569936 / (022 )39569959 /
(022) 39569967 / (022) 24952071
Indonesia
PT Robert Bosch
Palma Tower 10th Floor
Jalan RA Kartini II-S Kaveling 6
Pondok Pinang, Kebayoran Lama
Jakarta Selatan 12310
Tel.: (21) 3005-5800
www.bosch-pt.co.id
Malaysia
Robert Bosch Sdn. Bhd.(220975-V) PT/SMY
No. 8A, Jalan 13/6
46200 Petaling Jaya
Selangor
Tel.: (03) 79663194
Toll-Free: 1800 880188
Fax: (03) 79583838
E-mail: [email protected]
www.bosch-pt.com.my
Pakistan
Robert Bosch Middle East FZE – Pakistan Liaison Office
2nd Floor Plaza # 10, CCA Block, DHA Phase 5
Lahore, 54810
Phone: +92(303)4444311
E-mail: [email protected]
Philippines
Robert Bosch, Inc.
28th Floor Fort Legend Towers,
3rd Avenue corner 31st Street,
Fort Bonifacio, Global City,
1634 Taguig City
Tel.: (632) 8703871
Fax: (632) 8703870
www.bosch-pt.com.ph
Singapore
Powerwell Service Centre Ptd Ltd
Bosch Authorised Service Centre (Power Tools)
4012 Ang Mo Kio Ave 10, #01-02 TECHplace
Singapore 569628
Tel.: 6452 1770
Fax: 6452 1760
E-mail: [email protected]
www.powerwellsc.com
www.bosch-pt.com.sg
Thailand
Robert Bosch Ltd.
Liberty Square Building
No. 287, 11 Floor
Silom Road, Bangrak
Bangkok 10500
Tel.: 02 6393111
Fax: 02 2384783
Robert Bosch Ltd., P. O. Box 2054
Bangkok 10501
www.bosch.co.th
Bosch Service – Training Centre
La Salle Tower Ground Floor Unit No.2
10/11 La Salle Moo 16
Srinakharin Road
Bangkaew, Bang Plee
Samutprakarn 10540
Tel.: 02 7587555
Fax: 02 7587525
Vietnam
Branch of Bosch Vietnam Co., Ltd in HCMC
14th floor, Deutsches Haus, 33 Le Duan
Ben Nghe Ward, District 1, Ho Chi Minh City
Tel.: (028) 6258 3690
Fax: (028) 6258 3692 - 6258 3694
Hotline: (028) 6250 8555
E-mail: [email protected]
www.bosch-pt.com.vn
Armenia, Azerbaijan, Georgia, Kyrgyzstan, Mongolia,
Tajikistan, Turkmenistan, Uzbekistan
TOO "Robert Bosch" Power Tools, After Sales Service
Rayimbek Ave., 169/1
050050, Almaty, Kazakhstan
Service e-mail: [email protected]
Official website: www.bosch.com, www.bosch-pt.com
Bahrain
Hatem Al Juffali Technical Equipment Establishment.
Kingdom of Bahrain, Setra Highway, Al Aker Area
Phone: +966126971777-311
Fax: +97317704257
E-mail: [email protected]
Egypt
Unimar
20 Markaz kadmat
El tagmoa EL Aoul – New Cairo
Phone: +20 2224 76091-95
Phone: +20 2224 78072-73
Fax: +20222478075
E-mail: [email protected]
Iran
Robert Bosch Iran
3rd Floor, No 3, Maadiran Building
Aftab St., Khodami St., Vanak Sq.
Tehran 1994834571
Phone: +9821 86092057
Iraq
Sahba Technology Group
Al Muthana airport road
Baghdad
Phone: +9647901906953
Phone Dubai: +97143973851
E-mail: [email protected]
Jordan
Bosch Power Tools 1 609 92A 4J8 | (07.11.2018)
10 | English
Roots Arabia – Jordan
Nasser Bin Jameel street, Building 37 Al Rabiah
11194 Amman
Phone: +962 6 5545778
E-mail: [email protected]
Kuwait
Al Qurain Automotive Trading Company
Shuwaikh Industrial Area, Block 1, Plot 16, Street 3rd
P.O. Box 164 – Safat 13002
Phone: 24810844
Fax: 24810879
E-mail: [email protected]
Lebanon
Tehini Hana & Co. S.A.R.L.
P.O. Box 90-449
Jdeideh
Dora-Beirut
Phone: +9611255211
E-mail: [email protected]
Libya
El Naser for Workshop Tools
Swanee Road, Alfalah Area
Tripoli
Phone: +218 21 4811184
Oman
Malatan Trading & Contracting LLC
P.O. Box 131
Ruwi, 112 Sultanate of Oman
Phone: +968 99886794
E-mail: [email protected]
Qatar
International Construction Solutions W L L
P. O. Box 51,
Doha Phone: +974 40065458
Fax: +974 4453 8585
E-mail: [email protected]
Saudi Arabia
Juffali Technical Equipment Co. (JTECO)
Kilo 14, Madinah Road, Al Bawadi District
Jeddah 21431
Phone: +966 2 6672222 Ext. 1528
Fax: +966 2 6676308
E-mail: [email protected]
Syria
Dallal Establishment for Power Tools
P.O. Box 1030
Aleppo
Phone: +963212116083
E-mail: [email protected]
United Arab Emirates
Central Motors & Equipment LLC, P.O. Box 1984
Al-Wahda Street – Old Sana Building
Sharjah
Phone: +971 6 593 2777
Fax: +971 6 533 2269
E-mail: [email protected]
Yemen
Abualrejal Trading Corporation
Sana’a Zubiery St. Front to new Parliament Building
Phone: +967-1-202010
Fax: +967-1-279029
E-mail: [email protected]
Ethiopia
Forever plc
Kebele 2,754, BP 4806,
Addis Ababa
Phone: +251 111 560 600
E-mail: [email protected]
Ghana
C.WOERMANN LTD.
Nsawam Road/Avenor Junction, P.O. Box 1779
Accra Phone: +233 302 225 141
Kenya
Robert Bosch East Africa Ltd
Mpaka Road P.O. Box 856
00606 Nairobi
Nigeria
Robert Bosch Nigeria Ltd.
52–54 Isaac John Street P.O. Box
GRA Ikeja – Lagos
Republic of South Africa
Customer service
Hotline: (011) 6519600
Gauteng – BSC Service Centre
35 Roper Street, New Centre
Johannesburg
Tel.: (011) 4939375
Fax: (011) 4930126
E-mail: [email protected]
KZN – BSC Service Centre
Unit E, Almar Centre
143 Crompton Street
Pinetown
Tel.: (031) 7012120
Fax: (031) 7012446
E-mail: [email protected]
Western Cape – BSC Service Centre
Democracy Way, Prosperity Park
Milnerton
Tel.: (021) 5512577
Fax: (021) 5513223
E-mail: [email protected]
Bosch Headquarters
Midrand, Gauteng
Tel.: (011) 6519600
Fax: (011) 6519880
E-mail: [email protected]
Tanzania
Diesel & Autoelectric Service Ltd.
117 Nyerere Rd., P.O. Box 70839
Vingunguti 12109, Dar Es Salaam
Phone: +255 222 861 793/794
1 609 92A 4J8 | (07.11.2018) Bosch Power Tools
| 11
Australia, New Zealand and Pacific Islands
Robert Bosch Australia Pty. Ltd.
Power Tools
Locked Bag 66
Clayton South VIC 3169
Customer Contact Center
Inside Australia:
Phone: (01300) 307044
Fax: (01300) 307045
Inside New Zealand:
Phone: (0800) 543353
Fax: (0800) 428570
Outside AU and NZ:
Phone: +61 3 95415555
www.bosch-pt.com.au
www.bosch-pt.co.nz
Disposal
The power tool, accessories and packaging should be re-
cycled in an environmentally friendly manner.
Do not dispose of power tools along with
household waste.
警告！
u
u
u
u
u
u
u
u
u
u
u
u
u
u
u
u
u
u
u
u
u
u
Bosch Power Tools 1 609 92A 4J8 | (07.11.2018)
12 |
u
u
u
u
u
u
u
u
u
u
u
u
u
u
u
u
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(10)
(11)
(12)
(13)
(14)
GBS 75 A
3 601 B74 0..
710
350
/ 300
533
75
●
3.2
/ II
230[U]
u
1 609 92A 4J8 | (07.11.2018) Bosch Power Tools
| 13
u
u
u
u
u
u
Bosch Power Tools 1 609 92A 4J8 | (07.11.2018)
14 |
警告
u
u
u
u
u
u
u
u
u
u
u
u
1 609 92A 4J8 | (07.11.2018) Bosch Power Tools
| 15
u
u
u
u
u
u
u
u
u
u
u
u
u
u
u
u
u
u
u
u
u
u
u
u
u
u
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(10)
(11)
(12)
(13)
Bosch Power Tools 1 609 92A 4J8 | (07.11.2018)
16 |
(14)
GBS 75 A
3 601 B74 0..
W 710
W 350
m/min 300
mm 533
mm 75
●
kg 3.2
/ II
230
u
u
u
u
u
1 609 92A 4J8 | (07.11.2018) Bosch Power Tools
| 17
u
u
경고
u
u
u
u
Bosch Power Tools 1 609 92A 4J8 | (07.11.2018)
18 |
u
u
u
u
u
u
u
u
u
u
u
u
u
u
u
u
u
u
u
u
u
u
u
1 609 92A 4J8 | (07.11.2018) Bosch Power Tools
| 19
u
u
u
u
u
u
u
u
u
u
u
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(10)
(11)
(12)
(13)
(14)
GBS 75 A
3 601 B74 0..
W 710
W 350
m/min 300
mm 533
mm 75
●
kg 3.2
/ II
[U] 230V .
.
u
Bosch Power Tools 1 609 92A 4J8 | (07.11.2018)
20 |
u
u
u
u
1 609 92A 4J8 | (07.11.2018) Bosch Power Tools
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
他の言語で
- français: Bosch GBS 75 A Manuel utilisateur
関連論文
-
Bosch 550, 55-225 GTR Professional Drywall Sander ユーザーマニュアル
-
Bosch GWS 2200 ユーザーマニュアル
-
-
-
Bosch GSR 12V-35 HX ユーザーマニュアル
-
Bosch GSH 501 ユーザーマニュアル
-
Bosch GSH 500 PROFESSIONAL ユーザーマニュアル
-
-
-
Bosch GKS Professional ユーザーマニュアル
