DeWalt DCS373 ユーザーマニュアル

DCS373

2

English (original instructions) 5

简体中文 19

繁體中文 33

한국어 47

1

Figure 1

Figure 2

a

b

c

e

d

l

f

h

i

g

j

k

m

d

e

i

m

Figure 3

u

n

o

i

2

Figure 6

Figure 4

f

r

t

q

f

r

q

s

p

Figure 5

q

r

f

s

t

3

Figure 8Figure 7

Figure 9

d

c

A

B

d

13 mm

(1/2")

4

Figure 10

Figure 11

o

n

English

5

140 mm (5-1/2") 18V CORDLESS METAL-CUTTING

CIRCULAR SAW, DCS373

Congratulations!

You have chosen a DeWALT tool. Years of

experience, thorough product development and

innovation make DeWALT one of the most reliable

partners for professional power tool users.

Technical Data

DCS373

Voltage V

DC

18

Type 1

Max. power output W 460

No-load speed min

-1

3700

Blade diameter mm 140

Maximum depth of cut mm 43

Blade bore mm 20

Weight kg 0.49

Deﬁnitions: Safety Guidelines

The definitions below describe the level of severity

for each signal word. Please read the manual and

pay attention to these symbols.

DANGER: Indicates an imminently

hazardous situation which, if not avoided,

will result in death or serious injury.

WARNING: Indicates a potentially

hazardous situation which, if not

avoided, could result in death or

serious injury.

CAUTION: Indicates a potentially

hazardous situation which, if not

avoided, may result in minor or

moderate injury.

NOTICE: Indicates a practice not

related to personal injury which, if

not avoided, may result in property

damage.

Denotes risk of electric shock.

Denotes risk of fire.

Weight (without battery pack) kg 3.76

Battery pack DCB180 DCB181 DCB182 DCB183 DCB184

Battery type Li-Ion Li-Ion Li-Ion Li-Ion Li-Ion

Voltage V

DC

18 18 18 18 18

Capacity A

h

3.0 1.5 4.0 2.0 5.0

Weight kg 0.64 0.35 0.61 0.40 0.63

Charger DCB105

Mains voltage V

AC

220-240 V

Battery type Li-Ion

Approx. charging time min 30 55 70

(1.5 Ah battery packs) (3.0 Ah battery packs) (4.0 Ah battery packs)

English

6

General Power Tool Safety Warnings

WARNING! Read all safety warnings

and all instructions. Failure to follow

the warnings and instructions may result

in electric shock, fire and/or serious

injury.

Save all warningS and inStructionS

for future reference

The term “power tool” in the warnings refers to your

mains-operated (corded) power tool or battery-

operated (cordless) power tool.

1) WORK AREA SAFETY

a) Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of

flammable liquids, gases or dust. Power

tools create sparks which may ignite the dust

or fumes.

c) Keep children and bystanders away while

operating a power tool. Distractions can

cause you to lose control.

2) ELECTRICAL SAFETY

a) Power tool plugs must match the outlet.

Never modify the plug in any way. Do

not use any adapter plugs with earthed

(grounded) power tools. Unmodified plugs

and matching outlets will reduce risk of

electric shock.

b) Avoid body contact with earthed or

grounded surfaces such as pipes,

radiators, ranges and refrigerators. There

is an increased risk of electric shock if your

body is earthed or grounded.

c) Do not expose power tools to rain or wet

conditions. Water entering a power tool will

increase the risk of electric shock.

d) Do not abuse the cord. Never use the

cord for carrying, pulling or unplugging

the power tool. Keep cord away from

heat, oil, sharp edges o r moving parts.

Damaged or entangled cords increase the

risk of electric shock.

e) When operating a power tool outdoors,

use an extension cord suitable for outdoor

use. Use of a cord suitable for outdoor use

reduces the risk of electric shock.

f) If operating a power tool in a damp

location is unavoidable, use a residual

current device (RCD) protected supply.

Use of an RCD reduces the risk of electric

shock.

3) PERSONAL SAFETY

a) Stay alert, watch what you are doing and

use common sense when operating a

power tool. Do not use a power tool while

you are tired or under the influence of

drugs, alcohol or medication. A moment of

inattention while operating power tools may

result in serious personal injury.

b) Use personal protective equipment.

Always wear eye protection. Protective

equipment such as dust mask, non-skid

safety shoes, hard hat, or hearing protection

used for appropriate conditions will reduce

personal injuries.

c) Prevent unintentional starting. Ensure

the switch is in the off position before

connecting to power source and/or

battery pack, picking up or carrying the

tool. Carrying power tools with your finger

on the switch or energising power tools that

have the switch on invites accidents.

d) Remove any adjusting key or wrench

before turning the power tool on. A

wrench or a key left attached to a rotating

part of the power tool may result in personal

injury.

e) Do not overreach. Keep proper

footing and balance at all times. This

enables better control of the power tool in

unexpected situations.

f) Dress properly. Do not wear loose

clothing or jewellery. Keep your hair,

clothing and gloves away from moving

parts. Loose clothes, jewellery or long hair

can be caught in moving parts.

g) If devices are provided for the connection

of dust extraction and collection facilities,

ensure these are connected and properly

used. Use of dust collection can reduce

dust-related hazards.

4) POWER TOOL USE AND CARE

a) Do not force the power tool. Use the

correct power tool for your application.

The correct power tool will do the job

better and safer at the rate for which it

was designed.

b) Do not use the power tool if the switch

does not turn it on and off. Any power

tool that cannot be controlled with the switch

is dangerous and must be repaired.

c) Disconnect the plug from the power

source and/or the battery pack from

the power tool before making any

adjustments, changing accessories, or

storing power tools. Such preventive safety

measures reduce the risk of starting the

power tool accidentally.

English

7

d) Store idle power tools out of the reach

of children and do not allow persons

unfamiliar with the power tool or these

instructions to operate the power tool.

Power tools are dangerous in the hands of

untrained users.

e) Maintain power tools. Check for

misalignment or binding of moving parts,

breakage of parts and any other condition

that may affect the power tool’s operation.

If damaged, have the power tool repaired

before use. Many accidents are caused by

poorly maintained power tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp

cutting edges are less likely to bind and are

easier to control.

g) Use the power tool, accessories and

tool bits etc., in accordance with these

instructions taking into account the

working conditions and the work to

be performed. Use of the power tool for

operations different from those intended

could result in a hazardous situation.

5) BATTERY TOOL USE AND CARE

a) Recharge only with the charger specified

by the manufacturer. A charger that is

suitable for one type of battery pack may

create a risk of fire when used with another

battery pack.

b) Use power tools only with specifically

designated battery packs. Use of any

other battery packs may create a risk of

injury and fire.

c) When battery pack is not in use, keep it

away from other metal objects like paper

clips, coins, keys, nails, screws or other

small metal objects that can make a

connection from one terminal to another.

Shorting the battery terminals together may

cause burns or a fire.

d) Under abusive conditions, liquid may be

ejected from the battery, avoid contact.

If contact accidentally occurs, flush with

water. If liquid contacts eyes, additionally

seek medical help. Liquid ejected from the

battery may cause irritation or burns.

6) SERVICE

a) Have your power tool serviced by a

qualified repair person using only identical

replacement parts. This will ensure that the

safety of the power tool is maintained.

Safety Instructions for All Saws

a) Keep hands away from cutting area and the

blade. Keep your second hand on auxiliary

handle, or motor housing. If both hands are

holding the saw, they cannot be cut by the

blade.

b) Do not reach underneath the workpiece. The

guard cannot protect you from the blade below

the workpiece.

c) Adjust the cutting depth to the thickness

of the workpiece. Less than a full tooth of

the blade teeth should be visible below the

workpiece.

d) Never hold piece being cut in your hands or

across your leg. Secure the workpiece to a

stable platform. It is important to support the

work properly to minimise body exposure, blade

binding, or loss of control.

e) Hold power tool by insulated gripping

surfaces when performing an operation

where the cutting tool may contact hidden

wiring. Contact with a “live” wire will also make

exposed metal parts of the power tool “live” and

shock the operator.

f) When ripping always use a rip fence or

straight edge guide. This improves the

accuracy of cut and reduces the chance of

blade binding.

g) Always use blades with correct size and

shape (diamond versus round) of arbour

holes. Blades that do not match the mounting

hardware of the saw will run eccentrically,

causing loss of control.

h) Never use damaged or incorrect blade

washers or bolt. The blade washers and

bolt were specially designed for your saw, for

optimum performance and safety of operation.

Further Safety Instructions for All

Saws

CAUSES AND OPERATOR PREVENTION OF KICKBACK

– Kickback is a sudden reaction to a pinched,

bound or misaligned saw blade, causing an

uncontrolled saw to lift up and out of the

workpiece toward the operator;

– When the blade is pinched or bound tightly

by the kerf closing down, the blade stalls and

the motor reaction drives the unit rapidly back

toward the operator;

English

8

– If the blade becomes twisted or misaligned

in the cut, the teeth at the back edge of the

blade can dig into the top surface of the wood

causing the blade to climb out of the kerf and

jump back toward the operator.

Kickback is the result of saw misuse and/or incorrect

operating procedures or conditions and can be

avoided by taking proper precautions as given

below:

a) Maintain a firm grip with both hands on

the saw and position your arms to resist

kickback forces. Position your body to

either side of the blade, but not in line with

the blade. Kickback could cause the saw to

jump backwards, but kickback forces can be

controlled by the operator, if proper precautions

are taken.

b) When blade is binding, or when interrupting

a cut for any reason, release the trigger and

hold the saw motionless in the material until

the blade comes to a complete stop. Never

attempt to remove the saw from the work

or pull the saw backward while the blade is

in motion or kickback may occur. Investigate

and take corrective actions to eliminate the

cause of blade binding.

c) When restarting a saw in the workpiece,

centre the saw blade in the kerf and check

that saw teeth are not engaged into the

material. If saw blade is binding, it may walk up

or kickback from the workpiece as the saw is

restarted.

d) Support large panels to minimise the risk of

blade pinching and kickback. Large panels

tend to sag under their own weight. Supports

must be placed under the panel on both sides,

near the line of cut and near the edge of the

panel.

e) Do not use dull or damaged blades.

Unsharpened or improperly set blades produce

narrow kerf causing excessive friction, blade

binding and kickback.

f) Blade depth and bevel adjusting locking

levers must be tight and secure before

making cut. If blade adjustment shifts while

cutting, it may cause binding and kickback.

g) Use extra caution when sawing into existing

walls or other blind areas. The protruding

blade may cut objects that can cause kickback.

Lower Guard Safety Instructions

a) Check lower guard for proper closing before

each use. Do not operate the saw if lower

guard does not move freely and close

instantly. Never clamp or tie the lower guard

into the open position. If saw is accidentally

dropped, lower guard may be bent. Raise the

lower guard with the retracting handle and

make sure it moves freely and does not touch

the blade or any other part, in all angles and

depths of cut.

b) Check the operation of the lower guard

spring. If the guard and the spring are not

operating properly, they must be serviced

before use. Lower guard may operate

sluggishly due to damaged parts, gummy

deposits, or a build-up of debris.

c) Lower guard should be retracted manually

only for special cuts such as “plunge cuts”

and “compound cuts.” Raise lower guard

by retracting handle and as soon as blade

enters the material, the lower guard must be

released. For all other sawing, the lower guard

should operate automatically.

d) Always observe that the lower guard is

covering the blade before placing saw down

on bench or floor. An unprotected, coasting

blade will cause the saw to walk backwards,

cutting whatever is in its path. Be aware of the

time it takes for the blade to stop after switch is

released.

NOTE: Although the above information references

wood, this saw is only to be used to cut metal.

Kickback can occur when cutting metal.

Additional Speciﬁc Safety

Instructions for Circular Saws

 • Do not use abrasive wheels or blades.

 • Do not use water feed attachments.

 • Do not attempt to cut stainless steel, rebar,

hardened or heat-treated steel, cast iron,

masonry or unknown materials

 • Use clamps or another practical way to

secure and support the workpiece to a

stable platform. Holding the work by hand or

against your body leaves it unstable and may

lead to loss of control.

 • Keepyourbodypositionedtoeitherside

of the blade, but not in line with the saw

blade. KICKBACK could cause the saw to

jump backwards (see Causes and Operator

Prevention of Kickback and KICKBACK).

English

9

 • Air vents often cover moving parts and

should be avoided. Loose clothes, jewellery or

long hair can be caught in moving parts.

 • Wear ear protectors. Exposure to noise can

cause hearing loss.

 • Wearadustmask.Exposure to dust particles

can cause breathing difficulty and possible

injury.

 • Donotusebladesoflargerorsmaller

diameter than recommended. For the proper

blade rating refer to the Technical Data.

Use only the blades specified in this manual,

complying with EN 847-1.

 • Whennotinuse,placecircularsawona

stable surface, shoe side down, where it will

not cause a tripping or falling hazard. Some

tools with large battery packs will stand upright

on the battery pack but may be easily knocked

over.

Residual Risks

The following risks are inherent to the use of circular

saws.

– Injuries caused by touching the rotating parts or

hot part of the tool.

In spite of the application of the relevant safety

regulations and the implementation of safety

devices, certain residual risks cannot be avoided.

These are:

– Impairment of hearing.

– Risk of squeezing fingers when changing the

accessory.

– Health hazards caused by breathing dust

developed when working in wood.

Markings on Tool

The following pictograms are shown on the tool:

Read instruction manual before use.

Wear ear protection.

Wear eye protection.

DATE CODE POSITION (FIG. 1)

The date code (u), which also includes the year of

manufacture, is printed into the housing surface that

forms the mounting joint between tool and battery.

Example:

2013 XX XX

Year of Manufacture

Important Safety Instructions for All

Battery Chargers

SAVE THESE INSTRUCTIONS: This manual

contains important safety and operating instruc tions

for the DCB105 battery charger.

 • Beforeusingthecharger,readallinstructions

and cautionary markings on charger, battery

pack and product using the battery pack.

WARNING: Shock hazard. Do not allow

any liquid to get inside charger. Electric

shock may result.

CAUTION: Burn hazard. To reduce

the risk of injury, charge only

DeWALT

rechargeable battery packs. Other types

of batteries may overheat and burst

resulting in personal injury and property

damage.

CAUTION: Children should be

supervised to ensure that they do not

play with the appliance.

NOTICE: Under certain conditions, with

the charger plugged in to the power

supply, the exposed charging contacts

inside the charger can be shorted by

foreign material. Foreign materials of

a conductive nature such as, but not

limited to, steel wool, aluminum foil or

any buildup of metallic particles should

be kept away from charger cavities.

Always unplug the charger from the

power supply when there is no battery

pack in the cavity. Unplug charger

before attempting to clean.

 • DONOTattempttochargethebatterypack

with any chargers other than the ones in

this manual. The charger and battery pack are

specifically designed to work together.

 • Thesechargersarenotintendedfor

any uses other than charging

DeWALT

rechargeable batteries. Any other uses

may result in risk of fire, electric shock or

electrocution.

 • Donotexposechargertorainorsnow.

English

10

 • Pullbyplugratherthancordwhen

disconnecting charger. This will reduce risk

of damage to electric plug and cord.

 • Makesurethatcordislocatedsothatitwill

not be stepped on, tripped over or otherwise

subjected to damage or stress.

 • Donotuseanextensioncordunlessit

is absolutely necessary. Use of improper

extension cord could result in risk of fire,

electric shock or electrocution.

 • When operating a charger outdoors, always

provide a dry location and use an extension

cord suitable for outdoor use. Use of a cord

suitable for outdoor use reduces the risk of

electric shock.

 • Donotblocktheventilationslotsonthe

charger. The ventilation slots are located

on the top and sides of the charger. Place

the charger in a position away from any heat

source.

 • Donotoperatechargerwithdamagedcord

or plug — have them replaced immediately.

 • Do not operate charger if it has received

a sharp blow, been dropped or otherwise

damaged in any way. Take it to an authorised

service centre.

 • Donotdisassemblethecharger;takeitto

an authorised service centre when service or

repair is required. Incorrect reassembly may

result in a risk of electric shock, electrocution or

fire.

 • Incaseofdamagedpowersupplycordthe

supply cord must be replaced immediately by

the manufacturer, its service agent or similar

qualified person to prevent any hazard.

 • Disconnectthechargerfromtheoutlet

before attempting any cleaning. This will

reduce the risk of electric shock. Removing

the battery pack will not reduce this risk.

• NEVERattempt to connect 2 chargers together.

 • Thechargerisdesignedtooperateon

standard220-240Vhouseholdelectrical

power. Do not attempt to use it on any other

voltage. This does not apply to the vehicular

charger.

Save tHeSe inStructionS

Chargers

The DCB105 charger accepts 10.8 V, 14.4 V

and 18V Li-Ion (DCB121, DCB123, DCB140,

DCB141, DCB142, DCB143, DCB180, DCB181,

DCB182,DCB184 and DCB183) battery packs.

This charger requires no adjustment and is designed

to be as easy as possible to operate.

Charging Procedure (ﬁg. 2)

1. Plug the charger into an appropriate 230 V

outlet before inserting the battery pack.

2. Insert the battery pack (i) into the charger,

making sure the pack is fully seated in the

charger. The red (charging) light will blink

continuously indicating that the charging

process has started.

3. The completion of charge will be indicated by

the red light remaining ON continuously. The

pack is fully charged and may be used at this

time or left in the charger.

NOTE: To ensure maximum performance and life of

Li-Ion batteries, fully charge the pack before first use.

Charging Process

Refer to the table below for the state of charge of

the battery pack.

State of charge

charging –– –– –– ––

fully charged –––––––––––––––––

 hot/coldpackdelay ––•––•––• ––•

x

 problempackorcharger ••••••••••••

 problempowerline ••••••••••••

This charger will not charge a faulty battery pack.

The charger will indicate faulty battery by refusing to

light or by displaying problem pack or charger blink

pattern.

NOTE: This could also mean a problem with a

charger.

If the charger indicates a problem, take the charger

and battery pack to be tested at an authorised

service centre.

Hot/Cold Pack Delay

When the charger detects a battery that is too hot

or too cold, it automatically starts a hot/cold pack

delay, suspending charging until the battery has

reached an appropriate temperature. The charger

English

11

then automatically switches to the pack charging

mode. This feature ensures maximum battery life.

XR Li-Ion tools are designed with an Electronic

Protection System that will protect the battery

against overloading, overheating or deep discharge.

The tool will automatically turn off if the Electronic

Protection System engages. If this occurs, place the

Li-Ion battery on the charger until it is fully charged.

A cold battery pack will charge at about half the rate

of a warm battery pack. The battery pack will charge

at that slower rate throughout the entire charging

cycle and will not return to maximum charge rate

even if the battery warms.

Important Safety Instructions for All

Battery Packs

When ordering replacement battery packs, be sure

to include the catalog number and voltage.

The battery pack is not fully charged out of the

carton. Before using the battery pack and charger,

read the safety instructions below and then follow

the charging procedures outlined.

read all inStructionS

 • Donotchargeorusethebatterypack

in explosive atmospheres, such as in the

presence of flammable liquids, gases or

dust. Inserting or removing the battery pack

from the charger may ignite the dust or fumes.

• Never force the battery pack into charger.

Do not modify the battery pack in any way

to fit into a non-compatible charger as

battery pack may rupture causing serious

personal injury.

 • Chargethebatterypacksonlyindesignated

DeWALT chargers.

• DONOTsplash or immerse in water or other

liquids.

 • Donotstoreorusethetoolandbattery

pack in locations where the temperature

may reach or exceed 40°C (105°F) (such as

outside sheds or metal buildings in summer).

 • Forbestresults,makesurethebatterypackis

fully charged before use.

WARNING: Never attempt to open

the battery pack for any reason. If

the battery pack case is cracked or

damaged, do not insert it into the

charger. Do not crush, drop or damage

battery pack. Do not use a battery

pack or charger that has received a

sharp blow, been dropped, run over

or damaged in any way (e.g., pierced

with a nail, hit with a hammer, stepped

on). Electric shock or electrocution may

result. Damaged battery packs should

be returned to the service centre for

recycling.

CAUTION: When not in use, place

tool on its side on a stable surface

where it will not cause a tripping or

falling hazard. Some tools with large

battery packs will stand upright on the

battery pack but may be easily knocked

over.

SPECIFIC SAFETY INSTRUCTIONS FOR LITHIUM ION

(Li-Ion)

 • Donotincineratethebatterypackevenifit

is severely damaged or is completely worn

out. The battery pack can explode in a fire.

Toxic fumes and materials are created when

lithium ion battery packs are burned.

 • Ifbatterycontentscomeintocontactwith

the skin, immediately wash the area with

mild soap and water. If the battery liquid gets

into the eye, rinse water over the open eye for

15 minutes or until irritation ceases. If medical

attention is needed, the battery electrolyte

is composed of a mixture of liquid organic

carbonates and lithium salts.

 • Contentsofopenedbatterycellsmaycause

respiratory irritation. Provide fresh air. If

symptoms persists, seek medical attention.

WARNING: Burn hazard. Battery liquid

may be flammable if exposed to spark

or flame.

Battery Pack

BATTERY TYPE

The DCS373 operates on an 18 volt battery pack.

The DCB180, DCB181, DCB182 or DCB183 battery

packs may be used. Refer to Technical Data for

more information.

Storage Recommendations

1. The best storage place is one that is cool and

dry away from direct sunlight and excess heat

or cold. For optimum battery performance and

life, store battery packs at room temperature

when not in use.

2. For long storage, it is recommended to store a

fully charged battery pack in a cool, dry place

out of the charger for optimal results.

NOTE: Battery packs should not be stored

completely depleted of charge. The battery pack will

need to be recharged before use.

English

12

Labels on Charger and Battery Pack

In addition to the pictographs used in this manual,

the labels on the charger and the battery pack show

the following pictographs:

Read instruction manual before use.

Charging.

Fully charged.

Hot/cold pack delay.

x

Problem pack or charger.

Problem powerline.

Do not probe with conductive objects.

Do not charge damaged battery packs.

Use only with DeWALT battery packs.

Others may burst, causing personal injury

and damage.

Do not expose to water.

Have defective cords replaced

immediately.

Charge only between 4°C and 40°C.

Discard the battery pack with due care for

the environment.

Do not incinerate the battery pack.

Charges Li-Ion battery packs.

See Technical data for charging time.

Only for indoor use.

Package Contents

The package contains:

1 Cordless metal-cutting circular saw

1 30 tooth blade

1 Hex key

2 Li-Ion battery packs (M2 models)

1 Kitbox

1 Charger

1 Instruction manual

NOTE: Battery packs, chargers and kitboxes are not

included with N-models.

 • Checkfordamagetothetool,partsor

accessories which may have occurred during

transport.

 • Takethetimetothoroughlyreadand

understand this manual prior to operation.

Description (ﬁg. 1, 4–6)

WARNING: Never modify the power

tool or any part of it. Damage or

personal injury could result.

a. Trigger switch

b. Trigger switch lock-off button

c. Depth adjustment lever

d. Spindle lock button

e. Kerf indicator

f. Blade clamping screw

g. Lower guard

h. Lower guard retracting lever

i. Battery pack

j. Sight window

k. Shoe

l. Hex key

m. Battery release button

n. Main handle

o. Auxiliary handle

p. Fuel gauge button (fig. 4)

q. Inner clamp washer (fig. 5, 6)

r. Outer clamp washer (fig. 5, 6)

s. Saw spindle (fig. 5, 6)

t. Blade (fig. 5, 6)

English

13

INTENDED USE

This metal-cutting circular saw is intended for use

by professionals for cutting light gauge metals and

small metal structural shapes.

DO NOT use under wet conditions or in presence of

flammable liquids or gases.

This metal-cutting circular saw is a professional

power tool. DO NOT let children come into

contact with the tool. Supervision is required when

inexperienced operators use this tool.

 •Thisproductisnotintendedforusebypersons

(including children) suffering from diminished

physical, sensory or mental abilities; lack of

experience, knowledge or skills unless they are

supervised by a person responsible for their

safety. Children should never be left alone with

this product.

WARNING: Do not plunge cut or

pocket cut with this saw

WINDOW (FIG. 1)

WARNING: Do not operate the

saw with a damaged or missing

sight window. If window is damaged

or missing, have the saw serviced at

an authorised service centre. If saw is

operated without the window, metal

chips could fly through the guard and

cause personal injury.

CAUTION: Do not use oil or cutting

fluids with the metal-cutting saw.

Do not use cleaning fluids to clean

window. Cleaning fluids, cutting

fluids or oils could harm the plastic in

the window, interfering with the safe

operation of the saw.

The saw is equipped with a sight window (j) on the

side of the upper guard. This window allows the

user to see a cutting line on the material to be cut.

SAW SHOE (FIG. 1)

The front of the saw shoe (k) has a kerf indicator

(e) that allows the operator to glide the saw along

cutting lines. Aligning the cutting line with the notch

on the front of the shoe and centering it using the

modified V-shaped kerf indicator allows the operator

to keep the blade in line with the cutting line. If the

cutting line is visible through the narrowest part of

the kerf indicator, the blade will pass directly over the

cutting line.

WORKLIGHT

The saw is equipped with a worklight that is

activated when the trigger switch is depressed.

The light will automatically turn off 20 seconds after

the trigger switch is released. If the trigger switch

remains depressed, the worklight will remain on.

NOTE: The worklight is for lighting the immediate

work surface and is not intended to be used as a

flashlight.

Electrical Safety

The electric motor has been designed for one

voltage only. Always check that the battery pack

voltage corresponds to the voltage on the rating

plate. Also make sure that the voltage of your

charger corresponds to that of your mains.

Your DeWALT charger is double insulated

in accordance with IEC 60335; therefore

no earth wire is required.

If the supply cord is damaged, it must be replaced

by a specially prepared cord available through the

D

eWALT service organization.

Using an Extension Cable

An extension cord should not be used unless

absolutely necessary. Use an approved extension

cable suitable for the power input of your charger

(see Technical Data). The minimum conductor size

is 1 mm

2

; the maximum length is 30 m.

When using a cable reel, always unwind the cable

completely

ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of

serious personal injury, turn tool

off and disconnect battery pack

before making any adjustments or

removing/installing attachments or

accessories. An accidental start-up

can cause injury.

WARNING: Use only DeWALT battery

packs and chargers.

Inserting and Removing the

Battery Pack from the Tool (ﬁg. 3)

NOTE: For best results, make sure your battery

pack is fully charged. The light will shut off without

warning when the battery is fully discharged.

TO INSTALL THE BATTERY PACK INTO THE TOOL HANDLE

1. Align the battery pack (i) with the rails inside the

tool’s handle (fig. 3).

2. Slide it into the handle until the battery pack is

firmly seated in the tool and ensure that it does

not disengage.

English

14

TO REMOVE THE BATTERY PACK FROM THE TOOL

1. Press the battery release button (m) and firmly

pull the battery pack out of the tool handle.

2. Insert battery pack into the charger as

described in the charger section of this manual.

FUEL GAUGE BATTERY PACKS (FIG. 4)

Some D

eWALT battery packs include a fuel gauge

which consists of three green LED lights that

indicate the level of charge remaining in the battery

pack.

To actuate the fuel gauge, press and hold the fuel

gauge button (p). A combination of the three green

LED lights will illuminate designating the level of

charge left. When the level of charge in the battery

is below the usable limit, the fuel gauge will not

illuminate and the battery will need to be recharged.

NOTE: The fuel gauge is only an indication of the

charge left on the battery pack. It does not indicate

tool functionality and is subject to variation based

on product components, temperature and end-user

application.

Trigger Switch (ﬁg. 1)

WARNING: This tool has no provision

to lock the trigger switch in the ON

position and should never be locked ON

by any other means.

The saw is controlled by a trigger switch (a) and

lock-off button (b). The lock-off button must be

pressed before the trigger switch will turn the saw

on. Releasing the trigger turns the saw off.

Changing Blades (ﬁg. 1, 5–7)

TO INSTALL THE BLADE

1. Place inner clamp washer (q) on saw spindle (s)

with the large flat surface facing out toward the

blade (fig.5, 6).

2. Retract the lower blade guard (g) and place

blade (t) on saw spindle against the inner

clamp washer (q), making sure that the blade

will rotate in the proper direction (the direction

of the rotation arrow on the saw blade and

the teeth must point in the same direction as

the direction of rotation arrow on the saw). Do

not assume that the printing on the blade will

always be facing you when properly installed.

When retracting the lower blade guard to install

the blade, check the condition and operation

of the lower blade guard to assure that it is

working properly. Make sure it moves freely and

does not touch the blade or any other part, in all

angles and depths of cut.

3. Place the outer clamp washer (r) on the saw

spindle (s) with the large flat surface against the

blade (t) with beveled side facing out.

4. Thread the blade clamping screw (f) into the

saw spindle by hand. (Screw has left-hand

threads and must be turned counterclockwise

to tighten. Refer to arrow in Figure 7A.)

5. Depress the spindle lock button (d) while turning

the saw spindle with the hex key (l, fig.1) until

the spindle lock engages and the blade stops

rotating.

6. Tighten the blade clamping screw firmly with the

hex key.

NOTICE: Never engage the spindle

lock while saw is running, or engage

in an effort to stop the tool. Never turn

the saw on while the spindle lock is

engaged. Serious damage to your saw

will result.

TO REPLACE THE BLADE

1. To loosen the blade clamping screw (f), depress

the spindle lock button (d) and turn the saw

spindle (s) with the hex key (l) until the spindle

lock engages and the blade stops rotating.

With the spindle lock engaged, turn the blade

clamping screw clockwise with the hex key.

(Screw has left-hand threads and must be

turned clockwise to loosen. Refer to arrow in

Figure 7B.)

2. Remove the blade clamping screw (f) and outer

clamp washer (r) only. Remove old blade.

3. Clean any metal chips/shavings that may have

accumulated in the guard or clamp washer area

and check the condition and operation of the

lower blade guard as previously outlined. Do not

lubricate this area.

4. Select the proper blade for the application

(see Blades). Always use blades that are the

correct size (diameter) with the proper size

and shape centre hole for mounting on the

saw spindle. Always assure that the maximum

recommended speed (rpm) on the saw blade

meets or exceeds the speed (rpm) of the saw.

5. Follow steps 2 through 6 under To Install the

Blade, making sure that the blade will rotate in

the proper direction.

English

15

LOWER BLADE GUARD

WARNING: Under certain conditions

of use, metal chips may become

imbedded in the surfaces of the lower

guard, causing the lower guard to rub

against the upper guard. Check the

operation of the lower guard before

each use and remove any imbedded

chips.

WARNING: The lower blade guard is

a safety feature which reduces the

risk of serious personal injury. Never

use the saw if the lower guard is

missing, damaged, misassembled

or not working properly. Do not rely

on the lower blade guard to protect

you under all circumstances. Your

safety depends on following all

warnings and precautions as well

as proper operation of the saw.

Check lower guard for proper

closing before each use as outlined

in Additional Safety Rules for Circular

Saws. If the lower blade guard is

missing or not working properly,

have the saw serviced before

using. To assure product safety and

reliability, repair, maintenance and

adjustment should be performed

by an authorised service centre or

other qualified service organization,

always using identical replacement

parts.

BLADES

WARNING: To minimise the risk of

eye injury, always use eye protection.

Carbide is a hard but brittle material.

Foreign objects in the workpiece such

as wire or nails can cause tips to crack

or break. Only operate saw when proper

saw blade guard is in place. Mount

blade securely in proper rotation before

using, and always use a clean, sharp

blade.

Blade Diameter Teeth Application

DT1212-QZ 140mm 30 General purpose

(5-1/2") ferrous metal

cutting

If you need assistance regarding blades, please

contact your local D

eWALT dealer.

KICKBACK

Kickback is a sudden reaction to a pinched, bound

or misaligned saw blade, causing an uncontrolled

saw to lift up and out of the workpiece toward the

operator. When the blade is pinched or bound

tightly by the kerf closing down, the blade stalls

and the motor reaction drives the unit rapidly back

toward the operator. If the blade becomes twisted or

misaligned in the cut, the teeth at the back edge of

the blade can dig into the top surface of the material

causing the blade to climb out of the kerf and jump

back toward the operator.

Kickback is more likely to occur when any of the

following conditions exists.

1. IMPROPER WORKPIECE SUPPORT

A. Sagging or improper lifting of the cut off

piece can cause pinching of the blade and

lead to kickback (fig. 9).

B. Cutting through material supported at the

outer ends only can cause kickback. As the

material weakens it sags, closing down the

kerf and pinching the blade (fig. 9).

C. Cutting off a cantilevered or overhanging

piece of material from the bottom up in a

vertical direction can cause kickback. The

falling cut off piece can pinch the blade.

D. Cutting off long narrow strips can cause

kickback. The cut off strip can sag or twist

closing the kerf and pinching the blade.

E. Snagging the lower guard on a surface

below the material being cut momentarily

reduces operator control. The saw can lift

partially out of the cut increasing the chance

of blade twist.

2. IMPROPER DEPTH OF CUT SETTING ON

SAW

To make the most efficient cut, the blade should

protrude only far enough to expose a tooth

as shown in Figure 8. This allows the shoe to

support the blade and minimises twisting and

pinching in the material. See the section titled

Depth Adjustment.

3. BLADE TWISTING (MISALIGNMENT IN

CUT)

A. Pushing harder to cut can cause the blade to

twist.

B. Trying to turn the saw in the cut (trying to get

back on the marked line) can cause blade

twist.

English

16

C. Overreaching or operating the saw with poor

body control (out of balance), can result in

twisting the blade.

D. Changing hand grip or body position while

cutting can result in blade twist.

E. Backing up the saw to clear blade can lead

to twist.

4. USE OF DULL OR DIRTY BLADES

Dull blades cause increased loading of the

saw. To compensate, an operator will usually

push harder which further loads the unit and

promotes twisting of the blade in the kerf.

Worn blades may also have insufficient body

clearance which increases the chance of

binding and increased loading.

5. RESTARTING A CUT WITH THE BLADE

TEETH JAMMED AGAINST THE MATERIAL

The saw should be brought up to full operating

speed before starting a cut or restarting a cut

after the unit has been stopped with the blade

in the kerf. Failure to do so can cause stalling

and kickback.

Any other conditions which could result in pinching,

binding, twisting, or misalignment of the blade could

cause kickback. Refer to the sections Further

Safety Instructions for All Saws and Blades for

procedures and techniques that will minimise the

occurrence of kickback.

Depth Adjustment (ﬁg. 8)

WARNING: To reduce the risk of

serious personal injury, turn tool

off and disconnect battery pack

before making any adjustments or

removing/installing attachments or

accessories. An accidental start-up

can cause injury.

The metal-cutting saw is equipped with a pivoting

shoe that allows the operator to set the depth of cut.

For the most efficient cutting action, set the depth

adjustment so that one tooth of the blade projects

below the material to be cut. This distance is from

the tip of the tooth to the bottom of the gullet in front

of the tooth. This keeps blade friction at a minimum,

removes metal chips from the cut, results in cooler,

faster sawing and reduces the chance of kickback.

TO SET THE DEPTH OF CUT

1. Lay the piece of material you plan to cut along

the blade as shown.

2. Note how much tooth projects beyond the

material.

3. Loosen the depth adjustment lever (c) and

move the shoe to change the depth of cut.

4. Retighten the depth adjustment lever securely.

Workpiece Support (ﬁg. 9)

CUTTING SHEETS OF METAL

Figure 9 shows the correct and incorrect way to

support a large sheet. To avoid kickback, support

material near the cut. Do not support it away

from the cut. If material is supported away from

the cut, it will bind the blade and cause kickback.

When cutting thin strips, keep the blade at least

1/2" (approximately 13 mm) from the edge of the

material. Thin strips may bind, causing kickback and

increasing the risk of personal injury.

CUTTING RECTANGULAR METAL STOCK

Clamp the material you plan to cut to a workbench

or other work surface as shown above.

Cutting (ﬁg. 10, 11)

1. Hold the saw securely using both hands.

Figure10 shows appropriate hand position.

Keep your body to one side of the line along

which you are cutting. This will protect you from

injury related to kickback.

2. When cutting ends off of rectangular metal

stock, place the widest part of the shoe on

the part of the material that is clamped to the

workbench or other support, not on the part of

the material that will fall when the cut is made.

3. Depress the trigger switch and allow the saw to

reach full speed before the blade contacts the

material to be cut (fig. 11).

4. Push the saw forward at a speed that allows

the blade to cut without laboring.

5. As you finish a cut, release the trigger and allow

the blade to stop before lifting the saw from

the work. As you lift the saw, the guard will

automatically close under the blade.

CORRECTING A CUT

Should your cut begin to leave the cutting line, don’t

try to force it back on. Forcing a correction can stall

the saw and cause kickback. Instead, release the

switch and allow the blade to come to a complete

stop. Then, back the saw out of the cut. Restart

the saw and re-enter the cut, following the desired

cutting line.

CAUTION: Do not cut through bolts

with the metal-cutting saw. Damage to

the saw or personal injury could result.

English

17

Maximizing Blade Life

To extend blade life, follow these practices:

 • Donotforcethebladethroughthemetal.The

saw must cut at its own pace and at a constant

rate.

 • Changebladeswhenitisnolongereasyto

push the saw through the cut, when the motor

is straining, or when excessive heat is built up in

the blade.

 • Keepbaseofthesawfirmlyagainstmetalyou

are cutting.

 • Ifthemetalyouarecuttingisvibratingor

shaking, clamp the material as close to the cut

as possible and slow down the cutting rate.

OPERATION

WARNING: To reduce the risk of

serious personal injury, turn tool

off and disconnect battery pack

before making any adjustments or

removing/installing attachments or

accessories. An accidental start-up

can cause injury.

WARNING: Always wear proper

personal hearing protection. Under

some conditions and duration of use,

noise from this product may contribute

to hearing loss.

Instructions for Use

WARNING:

    • Alwaysobservethesafety

instructions and applicable

regulations.

    • Ensurethematerialtobesawnis

secured in place.

    • Applyonlyagentlepressuretothe

tool and do not exert side pressure

on the saw blade. If possible, work

with the saw shoe pressed against

the workpiece. This prevents damage

to the blade and stops the tool from

jerking and vibrating.

    • Avoidoverloading.

    • Letthebladerunfreelyforafew

seconds before starting the cut.

Proper Hand Position (ﬁg. 10)

WARNING: To reduce the risk of

serious personal injury, ALWAYS use

proper hand position as shown.

WARNING: To reduce the risk of

serious personal injury, ALWAYS hold

securely in anticipation of a sudden

reaction.

Proper hand position requires one hand on the

main handle (n), with the other hand on the auxiliary

handle (o), as shown in Figure 10, to guide the saw

properly.

MAINTENANCE

Your DeWALT power tool has been designed to

operate over a long period of time with a minimum

of maintenance. Continuous satisfactory operation

depends upon proper tool care and regular cleaning.

WARNING: To reduce the risk of

serious personal injury, turn tool

off and disconnect battery pack

before making any adjustments or

removing/installing attachments or

accessories. An accidental start-up

can cause injury.

Replacing Sight Window (ﬁg. 1)

WARNING: Do not operate the saw

with a damaged or missing sight

window. If window is damaged or

missing, have the saw serviced at an

authorised service centre. If the saw

is operated without the window, metal

chips could fly through the guard and

cause personal injury.

The sight window (j) must be replaced by an

authorised D

eWALT service centre.

CAUTION: Do not use any cleaning

fluids on the sight window to avoid

clouding it and compromising the safe

operation of the saw. Use compressed

air to remove accumulated dust from

the inside of the sight window. Wear

safety glasses when performing this.

The charger and battery pack are not serviceable.

There are no serviceable parts inside.

Lubrication

Your power tool requires no additional lubrication.

English

18

Cleaning

WARNING: Blow dirt and dust out of

the main housing with dry air as often as

dirt is seen collecting in and around the

air vents. Wear approved eye protection

and approved dust mask when

performing this procedure.

WARNING: Never use solvents or

other harsh chemicals for cleaning the

non-metallic parts of the tool. These

chemicals may weaken the materials

used in these parts. Use a cloth

dampened only with water and mild

soap. Never let any liquid get inside the

tool; never immerse any part of the tool

into a liquid.

CHARGER CLEANING INSTRUCTIONS

WARNING: Shock hazard. Disconnect

the charger from the AC outlet before

cleaning. Dirt and grease may be

removed from the exterior of the charger

using a cloth or soft non-metallic brush.

Do not use water or any cleaning

solutions.

Optional Accessories

WARNING: Since accessories, other

than those offered by D

eWALT, have

not been tested with this product, use

of such accessories with this tool could

be hazardous. To reduce the risk of

injury, only D

eWALT, recommended

accessories should be used with this

product.

Use only 140 mm (5-1/2") D

eWALT metal-cutting

blades with a 20mm arbor.

Consult your dealer for further information on the

appropriate accessories.

Protecting the Environment

Separate collection. This product must

not be disposed of with normal

household waste.

Should you ﬁnd one day that your D

eWALT product

needs replacement, or if it is of no further use to you,

do not dispose of it with household waste. Make this

product available for separate collection.

Separate collection of used products

and packaging allows materials to be

recycled and used again. Re-use of

recycled materials helps prevent

environmental pollution and reduces

the demand for raw materials.

Local regulations may provide for separate collection

of electrical products from the household, at

municipal waste sites or by the retailer when you

purchase a new product.

D

eWALT provides a facility for the collection and

recycling of DeWALT products once they have

reached the end of their working life. To take

advantage of this service please return your product

to any authorised repair agent who will collect them

on our behalf.

You can check the location of your nearest

authorised repair agent by contacting your local

D

eWALT office at the address indicated in this

manual. Alternatively, a list of authorised D

eWALT

repair agents and full details of our after-sales

service and contacts are available on the Internet at:

www.2helpU.com.

Rechargeable Battery Pack

This long life battery pack must be recharged when

it fails to produce sufficient power on jobs which

were easily done before. At the end of its technical

life, discard it with due care for our environment:

 • Runthebatterypackdowncompletely,then

remove it from the tool.

 • Li-Ioncellsarerecyclable.Takethemtoyour

dealer or a local recycling station. The collected

battery packs will be recycled or disposed of

properly.

ページが読み込まれています...

DeWalt DCS373 ユーザーマニュアル

DeWalt DCS373 ユーザーマニュアル

他の言語で

関連論文

その他のドキュメント