DCS320
DCS380
2
English (original instructions) 4
简体中文 15
한국어
24
Copyright DeWALT
1
Figure 1
DCS320
b
e
d
c
a
f
g
DCS380
b
a
f
g
e
d
c
h
h
2
Figure 3
Figure 5
Figure 2
g
f
a
b
Figure 4
Figure 6
f
i
3
Figure 7 Figure 8
Figure 9
Figure 10
Figure 11
1
2
Figure 12
e
h
ENGLISH
4
CORDLESS RECIPROCATING SAWS
DCS320, DCS380
Congratulations!
You have chosen a DeWALT tool. Years of experience, thorough product development and innovation make
DeWALT one of the most reliable partners for professional power tool users.
Technical Data
DCS320 DCS380
Voltage V
DC
14.4 18
Battery Type Li-Ion Li-Ion
Max. power output W 390 560
No-load speed min
-1
2400 2950
Stroke length mm 28.6 28.6
Weight (without battery pack) kg 2.7 2.7
Battery pack DCB140 DCB141 DCB142 DCB180 DCB181 DCB182 DCB184
Battery type Li-Ion Li-Ion Li-Ion Li-Ion Li-Ion Li-Ion Li-Ion
Voltage V
DC
14,4 14,4 14,4 18 18 18 18
Capacity A
h
3,0 1,5 4,0 3,0 1,5 4,0 5,0
Weight kg 0,53 0,30 0,54 0,64 0,35 0,61 0,63
Charger DCB105
Mains voltage V
AC
220 V
Battery type Li-Ion
Approx. charging time min 30 55 70 90
(1,5 Ah battery packs) (3,0 Ah battery packs) (4,0 Ah battery packs) (5,0 Ah battery packs)
Weight kg 0,49
the times when the tool is switched off
or when it is running but not actually
doing the job. This may significantly
reduce the exposure level over the total
working period.
Identify additional safety measures to
protect the operator from the effects of
vibration such as: maintain the tool and
the accessories, keep the hands warm,
organisation of work patterns.
The definitions below describe the level of severity
for each signal word. Please read the manual and
pay attention to these symbols.
DANGER: Indicates an imminently
hazardous situation which, if not avoided,
will result in death or serious injury.
Definitions: Safety Guidelines
The vibration emission level given in this information
sheet has been measured in accordance with a
standardised test given in EN 60745 and may be
used to compare one tool with another. It may be
used for a preliminary assessment of exposure.
WARNING: The declared vibration
emission level represents the main
applications of the tool. However if the
tool is used for different applications,
with different accessories or poorly
maintained, the vibration emission may
differ. This may significantly increase the
exposure level over the total working
period.
An estimation of the level of exposure to
vibration should also take into account
ENGLISH
5
WARNING: Indicates a potentially
hazardous situation which, if not
avoided, could result in death or
serious injury.
CAUTION: Indicates a potentially
hazardous situation which, if not
avoided, may result in minor or
moderate injury.
NOTICE: Indicates a practice not
related to personal injury which, if
not avoided, may result in property
damage.
Denotes risk of electric shock.
Denotes risk of fire.
WARNING: To reduce the risk of injury,
read the instruction manual.
General Power Tool Safety Warnings
WARNING! Read all safety warnings
and all instructions. Failure to follow
the warnings and instructions may result
in electric shock, fire and/or serious
injury.
SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTURE REFERENCE
The term “power tool” in the warnings refers to your
mains-operated (corded) power tool or battery-
operated (cordless) power tool.
1) WORK AREA SAFETY
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power
tools create sparks which may ignite the dust
or fumes.
c) Keep children and bystanders away while
operating a power tool. Distractions can
cause you to lose control.
2) ELECTRICAL SAFETY
a) Power tool plugs must match the outlet.
Never modify the plug in any way. Do
not use any adapter plugs with earthed
(grounded) power tools. Unmodified plugs
and matching outlets will reduce risk of
electric shock.
b) Avoid body contact with earthed or
grounded surfaces such as pipes,
radiators, ranges and refrigerators. There
is an increased risk of electric shock if your
body is earthed or grounded.
c) Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
d) Do not abuse the cord. Never use the
cord for carrying, pulling or unplugging
the power tool. Keep cord away from
heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the
risk of electric shock.
e) When operating a power tool outdoors,
use an extension cord suitable for outdoor
use. Use of a cord suitable for outdoor use
reduces the risk of electric shock.
f) If operating a power tool in a damp
location is unavoidable, use a residual
current device (RCD) protected supply.
Use of an RCD reduces the risk of electric
shock.
3) PERSONAL SAFETY
a) Stay alert, watch what you are doing and
use common sense when operating a
power tool. Do not use a power tool while
you are tired or under the influence of
drugs, alcohol or medication. A moment of
inattention while operating power tools may
result in serious personal injury.
b) Use personal protective equipment.
Always wear eye protection. Protective
equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce
personal injuries.
c) Prevent unintentional starting. Ensure
the switch is in the off position before
connecting to power source and/or
battery pack, picking up or carrying the
tool. Carrying power tools with your finger
on the switch or energising power tools that
have the switch on invites accidents.
d) Remove any adjusting key or wrench
before turning the power tool on. A
wrench or a key left attached to a rotating
part of the power tool may result in personal
injury.
e) Do not overreach. Keep proper
footing and balance at all times. This
enables better control of the power tool in
unexpected situations.
f) Dress properly. Do not wear loose
clothing or jewellery. Keep your hair,
clothing and gloves away from moving
parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
g) If devices are provided for the connection
of dust extraction and collection facilities,
ensure these are connected and properly
ENGLISH
6
used. Use of dust collection can reduce
dust-related hazards.
4) POWER TOOL USE AND CARE
a) Do not force the power tool. Use the
correct power tool for your application.
The correct power tool will do the job
better and safer at the rate for which it
was designed.
b) Do not use the power tool if the switch
does not turn it on and off. Any power
tool that cannot be controlled with the switch
is dangerous and must be repaired.
c) Disconnect the plug from the power
source and/or the battery pack from
the power tool before making any
adjustments, changing accessories, or
storing power tools. Such preventive safety
measures reduce the risk of starting the
power tool accidentally.
d) Store idle power tools out of the reach
of children and do not allow persons
unfamiliar with the power tool or these
instructions to operate the power tool.
Power tools are dangerous in the hands of
untrained users.
e) Maintain power tools. Check for
misalignment or binding of moving parts,
breakage of parts and any other condition
that may affect the power tool’s operation.
If damaged, have the power tool repaired
before use. Many accidents are caused by
poorly maintained power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are
easier to control.
g) Use the power tool, accessories and
tool bits etc., in accordance with these
instructions taking into account the
working conditions and the work to
be performed. Use of the power tool for
operations different from those intended
could result in a hazardous situation.
5) BATTERY TOOL USE AND CARE
a) Recharge only with the charger specified
by the manufacturer. A charger that is
suitable for one type of battery pack may
create a risk of fire when used with another
battery pack.
b) Use power tools only with specifically
designated battery packs. Use of any
other battery packs may create a risk of
injury and fire.
c) When battery pack is not in use, keep it
away from other metal objects like paper
clips, coins, keys, nails, screws or other
small metal objects that can make a
connection from one terminal to another.
Shorting the battery terminals together may
cause burns or a fire.
d) Under abusive conditions, liquid may be
ejected from the battery, avoid contact.
If contact accidentally occurs, flush with
water. If liquid contacts eyes, additionally
seek medical help. Liquid ejected from the
battery may cause irritation or burns.
6) SERVICE
a) Have your power tool serviced by a
qualified repair person using only identical
replacement parts. This will ensure that the
safety of the power tool is maintained.
Additional Safety Instructions for
Reciprocating Saws
• Hold power tool by insulated gripping
surfaces when performing an operation
where the cutting accessory may contact
hidden wiring. Cutting accessory contacting a
“live” wire will make exposed metal parts of the
power tool “live” and could give the operator an
electric shock.
• ALWAYSwearadustmask.Exposure to
dust particles can cause breathing difficulty and
possible injury.
• NEVER switch on the tool when the saw blade
is jammed in the workpiece or in contact with
the material.
• Keephandsawayfrommovingparts. Never
place your hands near the cutting area.
• Useextracautionwhencuttingoverhead
andpayparticularattentiontooverhead
wireswhichmaybehiddenfromview.
Anticipate the path of falling branches and
debris ahead of time.
• Do not operate this tool for long periods of
time. Vibration caused by the operating action
of this tool may cause permanent injury to
fingers, hands, and arms. Use gloves to provide
extra cushion, take frequent rest periods, and
limit daily time of use.
SWITCHING ON AND OFF
• Afterswitchingoff,neverattempttostopthe
saw blade with your fingers.
• Neverputthesawdownonatableorwork
bench unless switched off. The saw blade will
keep running briefly after the tool has been
switched off.
ENGLISH
7
WHEN SAWING
• Whenusingsawbladesspeciallydesignedfor
cutting wood remove all nails and metal objects
from the workpiece before starting work.
• Whereverpossible,useclampsandvicesto
fasten the workpiece securely.
• Donotattempttosawextremelysmall
workpieces.
• Donotbendtoofarforward.Makesure
that you always stand firmly, particularly on
scaffolding and ladders.
• Alwaysholdthesawwithbothhands.
• Forcuttingcurvesandpockets,useanadapted
saw blade.
CHECKING AND CHANGING THE SAW BLADE
• Onlyusesawbladesconformingtothe
specifications contained in these operating
instructions.
• Onlysharpsawbladesinperfectworking
condition should be used; cracked or bent saw
blades should be discarded and replaced at
once.
• Ensurethatthesawbladeissecurelyfixed.
Residual Risks
In spite of the application of the relevant safety
regulations and the implementation of safety
devices, certain residual risks cannot be avoided.
These are:
– Impairment of hearing.
– Risk of personal injury due flying particles.
– Risk of burns due to accessories becoming hot
during operation.
– Risk of personal injury due to prolonged use.
Markings on Tool
The following pictograms are shown on the tool:
Read instruction manual before use.
Wear ear protection.
Wear eye protection.
DATE CODE POSITION
The Date Code, which also includes the year of
manufacture, is printed into the housing surface that
forms the mounting joint between tool and battery.
Example:
2012 XX XX
Year of Manufacture
Important Safety Instructions for All
Battery Chargers
SAVETHESEINSTRUCTIONS: This manual
contains important safety and operating instruc tions
for the DCB105 battery charger.
• Beforeusingthecharger,readallinstructions
and cautionary markings on charger, battery
pack and product using the battery pack.
WARNING: Shock hazard. Do not allow
any liquid to get inside charger. Electric
shock may result.
CAUTION: Burn hazard. To reduce
the risk of injury, charge only DeWALT
rechargeablebatterypacks.Othertypes
of batteries may overheat and burst
resulting in personal injury and property
damage.
CAUTION: Children should be
supervised to ensure that they do not
play with the appliance.
NOTICE: Under certain conditions, with
the charger plugged in to the power
supply, the exposed charging contacts
inside the charger can be shorted by
foreign material. Foreign materials of
a conductive nature such as, but not
limited to, steel wool, aluminum foil or
any buildup of metallic particles should
be kept away from charger cavities.
Always unplug the charger from the
power supply when there is no battery
pack in the cavity. Unplug charger
before attempting to clean.
• DONOTattempttochargethebatterypack
with any chargers other than the ones in
this manual. The charger and battery pack are
specifically designed to work together.
• Thesechargersarenotintendedfor
any uses other than charging DeWALT
rechargeable batteries. Any other uses
may result in risk of fire, electric shock or
electrocution.
• Donotexposechargertorainorsnow.
ENGLISH
8
• Pullbyplugratherthancordwhen
disconnecting charger. This will reduce risk
of damage to electric plug and cord.
• Makesurethatcordislocatedsothatitwill
not be stepped on, tripped over or otherwise
subjected to damage or stress.
• Donotuseanextensioncordunlessit
is absolutely necessary. Use of improper
extension cord could result in risk of fire,
electric shock or electrocution.
• Whenoperatingachargeroutdoors,always
provide a dry location and use an extension
cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of
electric shock.
• Donotblocktheventilationslotsonthe
charger.Theventilationslotsarelocated
on the top and sides of the charger. Place
the charger in a position away from any heat
source.
• Donotoperatechargerwithdamagedcord
or plug — have them replaced immediately.
• Do not operate charger if it has received
a sharp blow, been dropped or otherwise
damaged in any way. Take it to an authorised
service centre.
• Donotdisassemblethecharger;takeitto
an authorised service centre when service or
repair is required. Incorrect reassembly may
result in a risk of electric shock, electrocution or
fire.
• Incaseofdamagedpowersupplycordthe
supply cord must be replaced immediately by
the manufacturer, its service agent or similar
qualified person to prevent any hazard.
• Disconnectthechargerfromtheoutlet
beforeattemptinganycleaning.Thiswill
reduce the risk of electric shock. Removing
the battery pack will not reduce this risk.
• NEVERattempt to connect 2 chargers together.
• Thechargerisdesignedtooperateon
standard220Vhouseholdelectricalpower.
Do not attempt to use it on any other
voltage. This does not apply to the vehicular
charger.
SAVE THESE INSTRUCTIONS
Chargers
The DCB105 charger accepts 10.8 V, 14.4 V and
18 V Li-Ion (DCB125, DCB127, DCB140, DCB141,
DCB180, DCB181 DCB182 and DCB184) battery
packs.
This charger requires no adjustment and is designed
to be as easy as possible to operate.
Charging Procedure (fig. 2)
1. Plug the charger into an appropriate 220 V
outlet before inserting the battery pack.
2. Insert the battery pack (f) into the charger,
making sure the pack is fully seated in the
charger. The red (charging) light will blink
continuously indicating that the charging
process has started.
3. The completion of charge will be indicated by
the red light remaining ON continuously. The
pack is fully charged and may be used at this
time or left in the charger.
NOTE: To ensure maximum performance and life of
Li-Ion batteries, charge the battery pack fully before
first use.
Charging Process
Refer to the table below for the state of charge of
the battery pack.
State of charge
charging –– –– –– ––
fully charged –––––––––––––––––
hot/coldpackdelay ––•––•––• ––•
x
problempackorcharger ••••••••••••
problempowerline ••••••••••••
This charger will not charge a faulty battery pack.
The charger will indicate faulty battery by refusing to
light or by displaying problem pack or charger blink
pattern.
NOTE: This could also mean a problem with a
charger.
If the charger indicates a problem, take the charger
and battery pack to be tested at an authorised
service centre.
Hot/Cold Pack Delay
When the charger detects a battery that is too hot
or too cold, it automatically starts a hot/cold pack
delay, suspending charging until the battery has
reached an appropriate temperature. The charger
then automatically switches to the pack charging
mode. This feature ensures maximum battery life.
XR Li-Ion tools are designed with an Electronic
Protection System that will protect the battery
against overloading, overheating or deep discharge.
ENGLISH
9
The tool will automatically turn off if the Electronic
Protection System engages. If this occurs, place the
Li-Ion battery on the charger until it is fully charged.
A cold battery pack will charge at about half the rate
of a warm battery pack. The battery pack will charge
at that slower rate throughout the entire charging
cycle and will not return to maximum charge rate
even if the battery warms.
Important Safety Instructions for All
Battery Packs
When ordering replacement battery packs, be sure
to include the catalog number and voltage.
The battery pack is not fully charged out of the
carton. Before using the battery pack and charger,
read the safety instructions below and then follow
the charging procedures outlined.
READ ALL INSTRUCTIONS
• Donotchargeorusethebatterypack
in explosive atmospheres, such as in the
presence of flammable liquids, gases or
dust. Inserting or removing the battery pack
from the charger may ignite the dust or fumes.
• Never force the battery pack into charger.
Do not modify the battery pack in any way
to fit into a non-compatible charger as
battery pack may rupture causing serious
personal injury.
• Chargethebatterypacksonlyindesignated
DeWALT chargers.
• DONOTsplash or immerse in water or other
liquids.
• Donotstoreorusethetoolandbattery
pack in locations where the temperature
may reach or exceed 40˚ C (105° F) (such as
outside sheds or metal buildings in summer).
• Forbestresults,makesurethebatterypackis
fully charged before use.
WARNING: Never attempt to open
the battery pack for any reason. If
the battery pack case is cracked or
damaged, do not insert it into the
charger. Do not crush, drop or damage
battery pack. Do not use a battery
pack or charger that has received a
sharp blow, been dropped, run over
or damaged in any way (e.g., pierced
with a nail, hit with a hammer, stepped
on). Electric shock or electrocution may
result. Damaged battery packs should
be returned to the service centre for
recycling.
CAUTION: When not in use, place
tool on its side on a stable surface
where it will not cause a tripping or
falling hazard. Some tools with large
battery packs will stand upright on the
battery pack but may be easily knocked
over.
SPECIFIC SAFETY INSTRUCTIONS FOR LITHIUM ION
(Li-Ion)
• Donotincineratethebatterypackevenifit
is severely damaged or is completely worn
out. The battery pack can explode in a fire.
Toxic fumes and materials are created when
lithium ion battery packs are burned.
• Ifbatterycontentscomeintocontactwith
the skin, immediately wash the area with
mild soap and water. If the battery liquid gets
into the eye, rinse water over the open eye for
15 minutes or until irritation ceases. If medical
attention is needed, the battery electrolyte
is composed of a mixture of liquid organic
carbonates and lithium salts.
• Contentsofopenedbatterycellsmaycause
respiratory irritation. Provide fresh air. If
symptoms persists, seek medical attention.
WARNING: Burn hazard. Battery liquid
may be flammable if exposed to spark
or flame.
Battery Pack
BATTERY TYPE
The DCS320 operates on 14.4 volt battery packs.
The DCS380 operates on 18 volt battery packs.
The DCB140, DCB141, DCB142, DCB180,
DCB181, DCB182 or DCB184 battery packs
may be used. Refer to Technical Data for more
information.
Storage Recommendations
1. The best storage place is one that is cool and
dry away from direct sunlight and excess heat
or cold. For optimum battery performance and
life, store battery packs at room temperature
when not in use.
2. For long storage, it is recommended to store a
fully charged battery pack in a cool, dry place
out of the charger for optimal results.
NOTE: Battery packs should not be stored
completely depleted of charge. The battery pack will
need to be recharged before use.
ENGLISH
10
Labels on Charger and Battery Pack
In addition to the pictographs used in this manual,
the labels on the charger and the battery pack show
the following pictographs:
Read instruction manual before use.
Charging.
Fully charged.
Hot/cold pack delay.
x
Problem pack or charger.
Problem powerline.
Do not probe with conductive objects.
Do not charge damaged battery packs.
Use only with DeWALT battery packs.
Others may burst, causing personal injury
and damage.
Do not expose to water.
Have defective cords replaced
immediately.
Charge only between 4° C and 40° C.
Discard the battery pack with due care for
the environment.
Do not incinerate the battery pack.
Charges Li-Ion battery packs.
See Technical Data for charging time.
Only for indoor use.
Package Contents
The package contains:
1 Cordless Reciprocating Saw
2 Li-Ion battery packs (L2, M2, P2 models)
1 Kitbox
1 Charger
1 Instruction manual
NOTE: Battery packs, chargers and kitboxes are not
included with N-models.
• Checkfordamagetothetool,partsor
accessories which may have occurred during
transport.
• Takethetimetothoroughlyreadand
understand this manual prior to operation.
Description (fig. 1)
WARNING: Never modify the power
tool or any part of it. Damage or
personal injury could result.
a. Trigger switch
b. Lock-off button
c. Blade clamp release lever
d. Shoe
e. Hand grip
f. Battery pack
g. Battery release button
h. Main handle
INTENDED USE
Your DCS320 and DCS380 cordless reciprocating
saws have been designed for professional sawing
of wood, metal and tubes. The compact design
permits cutting extremely close to the edge of
difficult areas.
DO NOT use under wet conditions or in presence of
flammable liquids or gases.
These reciprocating saws are professional power
tools.
DO NOT let children come into contact with the
tool. Supervision is required when inexperienced
operators use this tool.
•Thisproductisnotintendedforusebypersons
(including children) suffering from diminished
physical, sensory or mental abilities; lack of
experience, knowledge or skills unless they are
supervised by a person responsible for their
safety. Children should never be left alone with
this product.
ENGLISH
11
Electrical Safety
The electric motor has been designed for one
voltage only. Always check that the battery pack
voltage corresponds to the voltage on the rating
plate. Also make sure that the voltage of your
charger corresponds to that of your mains.
Your DeWALT charger is double insulated
in accordance with EN 60335; therefore
no earth wire is required.
If the supply cord is damaged, it must be replaced
by a specially prepared cord available through the
DeWALT service organization.
Using an Extension Cable
An extension cord should not be used unless
absolutely necessary. Use an approved extension
cable suitable for the power input of your charger
(see Technical data). The minimum conductor size
is 1 mm
2
; the maximum length is 30 m.
When using a cable reel, always unwind the cable
completely.
ASSEMBLY AND ADJUSTMENTS
WARNING: Prior to assembly and
adjustment, always remove the battery
pack. Always switch off the tool before
inserting or removing the battery pack.
WARNING: Use only DeWALT battery
packs and chargers.
Inserting and Removing the
Battery Pack from the Tool (fig. 3)
WARNING: To reduce the risk of injury,
never depress the battery release button
without removing the battery pack.
Depressing the battery release button
without removing the battery pack can
result in the battery pack falling out
unexpectedly.
NOTE: For best results, make sure your battery
pack is fully charged.
TO INSTALL THE BATTERY PACK INTO THE TOOL HANDLE
1. Align the battery pack (f) with the rails inside the
tool’s handle (fig. 3).
2. Slide it into the handle until the battery pack is
firmly seated in the tool and ensure that it does
not disengage.
TO REMOVE THE BATTERY PACK FROM THE TOOL
1. Press the battery release button (g) and firmly
pull the battery pack out of the tool handle.
2. Insert battery pack into the charger as
described in the charger section of this manual.
FUEL GAUGE BATTERY PACKS (FIG. 2)
Some DeWALT battery packs include a fuel gauge
which consists of three green LED lights that
indicate the level of charge remaining in the battery
pack.
To actuate the fuel gauge, press and hold the fuel
gauge button (i). A combination of the three green
LED lights will illuminate designating the level of
charge left. When the level of charge in the battery
is below the usable limit, the fuel gauge will not
illuminate and the battery will need to be recharged.
NOTE: The fuel gauge is only an indication of the
charge left on the battery pack. It does not indicate
tool functionality and is subject to variation based
on product components, temperature and end-user
application.
Variable Speed Trigger Switch
(fig. 4)
LOCK-OFF BUTTON AND TRIGGER SWITCH
Your saw is equipped with a lock-off button (b).
To lock the trigger switch, press the lock-off
button as shown in figure 4. Always lock the trigger
switch (a) when carrying or storing the tool to
eliminate unintentional starting. The lock-off button
is colored red to indicate when the switch is in its
unlocked position.
To unlock the trigger switch, press the lock-off
button as shown in figure 4. Pull the trigger switch
to turn the motor ON. Releasing the trigger switch
turns the motor OFF.
WARNING: This tool has no provision
tolocktheswitchintheONposition,
andshouldneverbelockedONbyany
other means.
The variable speed trigger switch will give you added
versatility. The further the trigger is depressed the
higher the speed of the saw.
CAUTION: Use of very slow speed is
recommended only for beginning a cut.
Prolonged use at very slow speed may
damage your saw.
ENGLISH
12
OPERATION
WARNING:Toreducetherisk
of serious personal injury, turn
tool off and disconnect tool from
powersourcebeforemakingany
adjustmentsorremoving/installing
attachments or accessories.
Blade Installation and Removal
(fig. 1, 5–7, 10)
Different blade lengths are available. Use the
appropriate blade for the application. The blade
should be longer than 89 mm (3-1/2") and should
extend past the shoe and the thickness of the
workpiece during the cut. Do not use jigsaw blades
with this tool.
WARNING: Cut hazard. Blade
breakage may occur if the blade
does not extend past the shoe and
the workpiece during the cut (fig. 5).
Increased risk of personal injury, as well
as damage to the shoe and workpiece
may result.
TO INSTALL BLADE INTO SAW
1. Pull blade clamp release lever (c) up (fig. 1).
2. Insert blade shank from the front.
3. Push blade clamp release lever down.
NOTE: The blade can be installed in four positions
as shown in figure 6. Both units allow the blade to
be installed upside-down to assist in flush-to cutting;
see figure 10.
TO REMOVE BLADE FROM SAW
CAUTION: Burn hazard. Do not touch
the blade immediately after use. Contact
with the blade may result in personal
injury.
1. Open up blade clamp release lever.
2. Remove blade.
Proper Hand Position (fig. 9)
WARNING: To reduce the risk of
serious personal injury, ALWAYS use
proper hand position as shown.
WARNING: To reduce the risk of
serious personal injury, ALWAYS hold
securely in anticipation of a sudden
reaction.
Proper hand position requires one hand on the hand
grip (e), with the other hand on the main handle (h).
Cutting with Blade in Horizontal
Position (fig. 7)
Your reciprocating saw is equipped with a horizontal
blade clamp. Installing a blade in the horizontal
orientation allows cutting close to floors, walls or
ceilings where limited clearance is available. Ensure
that the shoe is pressed against the framing to avoid
kickback.
Adjustable Shoe (fig. 8)
CAUTION: Cut hazard. To prevent loss
of control, never use tool without shoe.
Your reciprocating saw comes with an adjustable
shoe. The shoe will adjust to limit the depth of cut.
Hold the saw with the underside facing up. Push the
button on the hand grip and slide the shoe out to
one of the three settings and release the button.
Cutting (fig. 9–12)
WARNING: Always use eye
protection. All users and bystanders
must wear approved eye protection.
WARNING: Exercise extra caution
when cutting towards operator. Always
hold saw firmly with both hands while
cutting.
Before cutting any type of material, be sure it is
firmly anchored or clamped to prevent slipping.
Place blade lightly against work to be cut, switch
on saw motor and allow it to obtain maximum
speed before applying pressure. Whenever
possible, the saw shoe must be held firmly against
the material being cut (fig. 9). This will prevent the
saw from jumping or vibrating and minimize blade
breakage. Any cuts which put pressure on the
blade such as angle or scroll cuts increase potential
for vibration, kickback, and blade breakage.
WARNING: Use extra caution when
cutting overhead and pay particular
attention to overhead wires which may
be hidden from view. Anticipate the path
of falling branches and debris ahead of
time.
WARNING: Inspect work site for
hidden gas pipes, water pipes, or
electrical wires before making blind
or plunge cuts. Failure to do so may
result in explosion, property damage,
electric shock, and/or serious personal
injury.
ENGLISH
13
FLUSH-TO CUTTING (FIG. 10)
The compact design of the saw motor housing and
spindle housing permits extremely close cutting to
floors, corners and other difficult areas.
POCKET/PLUNGE CUTTING – WOOD ONLY (FIG. 11)
The initial step in pocket cutting is to measure the
surface area to be cut and mark clearly with a
pencil, chalk or scriber. Use the appropriate blade
for the application. The blade should be longer than
8.89 cm (3-1/2") and should extend past the shoe
and the thickness of the workpiece during the cut.
Insert blade in blade clamp.
Next, tip the saw backward until the back edge
of the shoe is resting on the work surface and the
blade clears the work surface (position 1, fig. 11).
Now switch motor on, and allow saw to come up to
speed. Grip saw firmly with both hands and begin
a slow, deliberate upward swing with the handle
of the saw, keeping the bottom of the shoe firmly
in contact with the workpiece (position 2, fig. 11).
Blade will begin to feed into material. Always be
sure blade is completely through material before
continuing with pocket cut.
NOTE: In areas where blade visibility is limited, use
the edge of the saw shoe as a guide. Lines for any
given cut should be extended beyond edge of cut
to be made.
METAL CUTTING (FIG. 12)
Your saw has different metal cutting capacities
depending upon type of blade used and the metal
to be cut. Use a finer blade for ferrous metals
and a coarse blade for non-ferrous materials. In
thin gauge sheet metals it is best to clamp wood
to both sides of sheet. This will insure a clean cut
without excess vibration or tearing of metal. Always
remember not to force cutting blade as this reduces
blade life and causes costly blade breakage.
NOTE: It is generally recommended that when
cutting metals you should spread a thin film of oil or
other lubricant along the line ahead of the saw cut
for easier operation and longer blade life.
MAINTENANCE
Your DeWALT power tool has been designed to
operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
WARNING:Toreducetheriskof
serious personal injury, turn tool
offanddisconnectbatterypack
beforemakinganyadjustmentsor
removing/installingattachmentsor
accessories. An accidental start-up
can cause injury.
The charger and battery pack are not serviceable.
There are no serviceable parts inside.
Lubrication
Your power tool requires no additional lubrication.
Cleaning
WARNING: Blow dirt and dust out of
the main housing with dry air as often as
dirt is seen collecting in and around the
air vents. Wear approved eye protection
and approved dust mask when
performing this procedure.
WARNING: Never use solvents or
other harsh chemicals for cleaning the
non-metallic parts of the tool. These
chemicals may weaken the materials
used in these parts. Use a cloth
dampened only with water and mild
soap. Never let any liquid get inside the
tool; never immerse any part of the tool
into a liquid.
CHARGER CLEANING INSTRUCTIONS
WARNING: Shock hazard. Disconnect
the charger from the AC outlet before
cleaning. Dirt and grease may be
removed from the exterior of the charger
using a cloth or soft non-metallic brush.
Do not use water or any cleaning
solutions.
Optional Accessories
WARNING: Since accessories, other
than those offered by DeWALT, have
not been tested with this product, use
of such accessories with this tool could
be hazardous. To reduce the risk of
injury, only DeWALT recommended
accessories should be used with this
product.
Consult your dealer for further information on the
appropriate accessories.
ENGLISH
14
Protecting the Environment
Separate collection. This product must
not be disposed of with normal
household waste.
Should you find one day that your DeWALT
product needs replacement, or if it is of no further
use to you, do not dispose of it with household
waste. Make this product available for separate
collection.
Separate collection of used products
and packaging allows materials to be
recycled and used again. Re-use of
recycled materials helps prevent
environmental pollution and reduces
the demand for raw materials.
Local regulations may provide for separate collection
of electrical products from the household, at
municipal waste sites or by the retailer when you
purchase a new product.
DeWALT provides a facility for the collection and
recycling of DeWALT products once they have
reached the end of their working life. To take
advantage of this service please return your product
to any authorised repair agent who will collect them
on our behalf.
You can check the location of your nearest
authorised repair agent by contacting your local
DeWALT office at the address indicated in this
manual. Alternatively, a list of authorised DeWA LT
repair agents and full details of our after-sales
service and contacts are available on the Internet at:
www.2helpU.com.
Rechargeable Battery Pack
This long life battery pack must be recharged when
it fails to produce sufficient power on jobs which
were easily done before. At the end of its technical
life, discard it with due care for our environment:
• Runthebatterypackdowncompletely,then
remove it from the tool.
• Li-Ioncellsarerecyclable.Takethemtoyour
dealer or a local recycling station. The collected
battery packs will be recycled or disposed of
properly.
简体中文
15
祝贺您！
感谢您选择得伟工具。凭借多年的经验以及全面的产品开发与创新，得伟已经成为专业电动工具使用者最值
得信赖的伙伴之一。
如果你对这款或者任何的得伟工具有任何的疑问或者意见，请致电：800-820-4221或者 400-620-4221
锂电充电式往复锯
DCS320, DCS380
技术数据
DCS320 DCS380
电压 V
DC
14.4 18
电池类型 锂电 锂电
空载转速 转/分 2400 2950
行程长度 毫米 28.6 28.6
重量 千克 2.7 2.7
电池组 DCB140 DCB141 DCB142 DCB180 DCB181 DCB182 DCB184
电池类型 锂电 锂电 锂电 锂电 锂电 锂电 锂电
电压 V
DC
14,4 14,4 14,4 18 18 18 18
容量 安时 3,0 1,5 4,0 3,0 1,5 4,0 5,0
重量 千克 0,53 0,30 0,54 0,64 0,35 0,61 0,63
充电器 DCB105
电源电压 V
AC
220 V
电池类型 锂电
大约充电时间 分钟 30 55 70 90
(1,5 安时电池组) (3,0 安时电池组) (4,0 安时电池组) (5,0 安时电池组)
重量 千克 0,49
危险: 指示紧急的危险情形，如不加以
避免，将导致死亡或严重伤害
警告：指示潜在的危险情形，如不加以避
免，可能导致死亡或严重伤害。
警示：指示潜在的危险情形，如不加以避
免 ，可 能 导 致 轻 度 或 中 度 伤 害 。.
注 意 ：指 示 不 涉 及 人 身 伤 害 的 情 况 ，如
不加以避免，可能导致财产损失。
表示有触电风险。
表示存在火灾风险。
警告：为 降 低 伤 害 风 险 ，请 阅 读 使 用 手
册。
.电动工具一般安全警告
警告！请仔细阅读所有安全警告和指示
说明。不遵循下列的警告和指示则可能
会导致触电、火灾和/或严重伤害
请保存所有警告和指示，
以备将来查阅。
1 、工 作 场 所 安 全
a) 保持工作场地清洁和明亮。混乱和黑暗的场地会
引发事故。
b) 不要在易爆环境，如有易燃液体、气体或粉尘的
环境下操作电动工具。电动工具产生的火花会点燃粉
尘或气体。
c) 让儿童和旁观者离开后操纵电动工具。分心会使
你放松控制。
简体中文
16
2 、电 气 安 全
a) 电动工具插头必须与插座相配。不能以任何方式
改装插头。需接地的电动工具不能使用任何转换插
头。未经改装的插头和相配的插座将减少触电危险。
b) 避免人体接触接地表面，如管道、散热片和冰箱。
如果你身体接地会增加触电危险。
c) 不得将电动工具暴露在雨中或潮湿环境中。水进
入电动工具将增加触电危险。
d) 不得滥用电线。绝不能用电线搬运、拉动电动工
具或拔出其插头。让电动工具远离热、油、锐边或运
动 部 件 。受 损 或 缠 绕 的 电 线 会 增 加 触 电 危 险 。
e) 当在户外使用电动工具时，使用适合户外使用的
外接电线。适合户外使用的电线将减少触电危险。
f) 如果在潮湿的环境中使用电动工具，请使用漏电
保护装置（RCD）。使用此装置可降低触电危险。
3) 人身安全
a) 保持警觉，当操作电动工具时关注所从事的操作
并保持清醒。切勿在有疲倦、药物、酒精或治疗反应
下操作电动工具。在操作电动工具期间精力分散会导
致严重人身伤害。
b) 使用安全装置。始终配戴护目镜。安全装置，诸如
适 当 条 件 下 的 防 尘 面 具 、防 滑 安 全 鞋 、安 全 帽 、听 力
防 护 等 装 置 能 减 少人 身 伤 害。
c) 避免突然起动。确保开关在插入插头时处于关断
位置。手指放在已接通电源的开关上或开关处于接
通时插入头可能会导致危险。
d) 在电动工具接通之前，拿掉所有调节钥匙或扳
手。遗留在电动工具旋转零件上的扳手或钥匙会导致
人身伤害。
e) 手不要伸得太长。时刻注意脚下和身体平衡。这
样在意外情况下能很好地控制电动工具。
f) 着装适当。不要穿宽松衣服或佩带饰品。让你的
头发、衣服和袖子远离运动部件。宽松衣服、佩饰或
长发可能会卷入运动部件。
g ) 如 果 提 供 了 与 排 屑 装 置 、集 尘 设 备 连 接 用 的 装
置，则确保他们连接完好且使用得当。使用这些装置
可减少碎屑引起的危险。
4）电动工具使用和注意事项
a) 不要滥用电动工具，根据用途使用适当的电动工
具。选用适当的设计额值的电动工具会使你工作有
效 、更 安 全 。
b) 如果开关不能接通或关断工具电源，则不能使用
该电动工具。不能用开关来控制的电动工具是危险的
且必须进行修理。
c) 在进行任何调节、更换附件或贮存电动工具之
前，必须从电源上拔掉插头和／或将电池盒脱开电
源。这种防护性措施将减少电动工具突然起动的危
险。
d) 将闲置电动工具贮存在儿童所及范围之外，并且
不要让不熟悉电动工具或对这些说明不了解的人操
作电动工具。电动工具在未经训练的用户手中是危险
的。
e) 保养电动工具。检查运动部件的安装偏差或卡
住、零件破损情况和影响电动工具运行的其它条件。
如有损坏，电动工具必须在使用前修理好。许多事故
由维护不良的电动工具引发。
f) 保持切削刀具锋利和清洁。保养良好的有锋利切
削刃的刀具不易卡住而且容易控制。
g) 按照使用说明书以及打算使用的电动工具的特殊
类型要求的方式，考虑作业条件和进行的作业来使
用电动工具、附件和工具的刀头等。电动工具用作那
些与要求不符的操作可能会导致危险情况。
5、电池式工具使用和注意事项
a) 只用制造商规定的充电器充电。将适用于某种电
池盒的充电器用到其他电池盒时会发生着火危险。
b) 只使用配有特制电池盒的电动工具。使用其他电
池盒会发生损坏和着火危险。
c) 当电池盒不用时，将它远离其他金属物体，例如回
形针、硬币、钥匙、钉子、螺钉或其他小金属物体，以
防一端与另一端连接。电池端部短路会引起燃烧或者
火灾。
d) 在滥用条件下，液体会从电池中溅出；避免接触。
如果无意间碰到了，用水冲洗。如果液体碰到了眼
睛，还要寻求医疗帮助。从电池中溅出的液体会发生
腐蚀或燃烧。
6 、维 修
让专业维修人员使用特定的备件维修电动工具。这
将保证所维修的电动工具的安全。
电气安全
一台电动工具的电机只适配一个电压范围。务必检查
电源对应铭牌上的电压。在此额定电压外工作会导致
动力损失并且会导致过热。所有得伟的工具都在工厂
测 试 过 。如 果 此 工 具 不 正 常 运 作 ，请 检 查 电 源 。
年轻的儿童和体弱多病者。在没有监督的情况下，儿
童和体弱多病者不建议使用。
-只有在有人负责安全的情况下，体力虚弱者，视力，
精神状态虚弱者，缺少经验和知识的人（包括孩童）
不建议使用此工具。
-儿童必须被监护以确保他们没有把电动工具当玩具
电源线的更换 如果电源线或者插头损坏了，必须找
生产商或者经得伟授权的服务中心以避免危险。
简体中文
17
延长线
警示 只适用当国电气机构认可的延长线。在使用延
长线前，检查是否有松弛或者外露的电线，损坏的绝
缘体和有缺陷的固件。如必要，更换之。
往复锯安全须知
在切削附件可能触及暗线进行操作时，要通过绝缘
握持面来握持工具。切削附件碰到带电导线会使工具
外露的金属零件带电从而使操作者受到电击。
使用夹头或者其他可行的方法来确保工作对象在一
个固定的平台上。用手握住工作对象并使自己的身体
稍微远离工作对象。这样可以避免在不稳的情况下对
其失去控制。
在进行所有的切割操作时，用双手稳固的握住锯。在
切割工作中，锯条可能会突然卡在工作对象中并对操
作者产生反作用力。
避免手靠近运动的部分。不要让手靠近切割中的区
域。
请对那些高于头顶不容易被注意到的电线给予额外
的注意。
不要长时间的使用电动工具。操作中产生的震动可能
会对手指，手掌和手臂造成永久的伤害。使用手套进
行额外的保护，并间歇性的给予休息和限制一天中的
工作时长。
警告:我们推荐使用家用的能把电流限制
在30安培及以下的限电器。
警告:切记佩戴相应的安全保护设施。
警告: 一 些 有 磨 ，锯 ，钻 以 及 其 他 包 含 化
学成分的工业行为所产生的粉尘会导致
癌症，生育问题疾病和其他再生系统疾
病。
含铅油漆释放的铅
砖头，水泥以及其他一些泥石物体中的晶体硅
化 学 处 理 过 的 含 有 砷 ，铬 的 木 材
工作者是否经常工作决定了工作者是否会被这些物
质感染。要减少对于这些物质的曝光摄氏度，请在一
个通风很好的地方工作，穿着有认可的安全装备例如
特殊设计过有出尘功能的防尘面罩。
请勿过长时间接触磨，锯，钻和其他工业活动。穿着
有防护的衣服并且用肥皂水洗刷工作环境。让粉尘
进入人的口鼻或者粘着在皮肤上可能会促进吸收有
害的化学物质。
警告:当 电 动 工 具 不 使 用 时 ，请 将 其 放 在
一个平稳的地方，不会使其有掉落的危
险。
所有电池包的重要安全事项
当订购更换的电池包时，请确保信息包含目录号和电
压。查询此手册最后电池电器匹配表。
电池包在开包前电量不是满额的。在使用电池包和充
电前，请阅读一下的安全注意事项并按此执行。
不要在让充电和电池包放在有可能会引起爆炸的环
境中例如有可燃性液体，气体和粉尘。装载拆卸电池
包都有可能引燃粉尘和烟雾。
切勿强行为电池包充电。请勿以任何形式改装电池包
来适配一个本来不匹配的充电器。这种不匹配性会导
致严重的个人伤害。请查询附录表格来找到相适配的
电池和充电器。
请使用有得伟标志的充电器来充电。
切勿将电池包浸入水中或其他液体中。
切勿将电池包在一个工作环境会超过40摄氏摄氏度
的 放 置 。例 如 户 外 帐 篷 或 者 夏 季 的 特 质 工 业 棚 。请 将
电池包放置在一个干燥凉爽的环境中。
提示：不要将电池包放在一个扣动开关锁住的工具
中。切勿将扣动开关调至开启位置。
警告:火灾危险。切勿试图以任何理由拆
开电池包。如果电池包有裂开或者损坏，
请 勿 将 其 再 插 入 充 电 器 。切 勿 粉 碎 ，摔 或
这 损 坏 电 池 包 。不 要 使 用 有 裂 痕 的 ，被 摔
过的，过摄氏度使用的或者被损坏过的
电池包或者充电器。例如： 被钉子穿透
的，被铁锤锤过的，被脚踏过的等）损坏
的电池包应该被退回服务中心回收掉。
警告:火灾危险。不要储存或者携带电池
包。这样的话外界金属物会接触到电池
包。例如，不要把电池包放置在有掉落钉
子 ，螺 丝 和 钥 匙 的 围 裙 ，口 袋 ，工 具 盒 ，
产品包箱，抽屉等中。携带运输电池可能
引 起 火 灾 。所 以 当 需 要 运 输 耽 搁 电 池 包
时，保证电池终端是绝缘的。
简体中文
18
锂电池的详细安全注意事项
不允许焚化电池包即使电池包已经被严重损坏并且
完全不能使用。电池包会在火中爆炸。有毒的气体和
物质将被释放出。
如 果 电 池 中 的 的 物 质 接 触 了 皮 肤 ，请 立 即 用 中 性 肥
皂和水清洗。如果电池液进入眼睛中，用流水睁眼冲
洗15分钟以上或直至不适停止。可能有医疗需求，因
为蓄电池电解液组成的液体有机碳酸酯的混合物锂
盐。
开放的电池原件包含物可能会导致呼吸混乱。在此情
况下，提供新鲜空去。如果症状还在，请寻求医疗救
助。
警告:燃烧危险。电池液在产生火花或火
焰的环境中可能会燃烧
所有电池充电器的重要的安全注意事项
保存好这份说明书：这本说明书涉及到了重要的电池
的安全和操作。
在使用充电器之前，详阅说明书并且小心翼翼地在电
池包上做记号。
警告:触 电 危 险 。切 勿 让 任 何 的 液 体 进 入
充电器否则会有触电危险。
警告:燃 烧 危 险 。为 了 减 少 伤 害 的 机 率 ，
请指安得伟的可回收充电包进行充电。
注意：在以下情况下，即使充电器插入电源，充电器
寿命会因外国材料的缩短。国外的导电性材料例如
打 磨 的 灰 尘 ，金 属 屑 ，钢 丝 绒 ，铝 箔 或 任 何 金 属 颗 粒
堆积应远离从充电器座。切记在如果充电器座里没有
电池包时，拔下电源。如果你想清洁充电器拔下充电
器。
不要试图为不匹配此充电器的电池包充电。电池和电
池包是一一相匹配的。
些充电器只为得伟可充式充电器设计。任何其他的充
电 匹 配 会 有 火 灾 ，电 气 和 触 电 的 危 险 。
不要将充电器暴露在雨中或者雪中。
当想断开充电器时切忌拔插座而不是电线。这样会减
少损坏电气插头和电线的可能性。
确保电线被固定住不会被人踏到，弯曲或者其他压力
下的损坏。
在非不得已的情况下请不要使用外接电线。使用不合
适的外接电线可能会引起火灾，电击或者电气事故。
当在户外使用充电器时，切记提供一个干燥的环境并
且使用适合的外接电线。使用的合适的外接电线能
够降低触电的机率。
不要在充电器上放置任何其他物体，也不要将充电器
放在一个柔软的平面上使得充电器不能够散热导致
内部过热的现象。把充电器放置在一个离开热源的位
置。充电器的散热主要通过槽和底板。
不要用损坏的电线和插座来运行充电。
这如果充电器出现裂缝，被摔过或者其他任何的损坏
就不要使用充电器。拿去授权的服务中心维修。
不要私自拆卸充电器。拿去授权的服务中心修理。错
误的重组充电器会导致触电和电气事故。
清洗充电器前务必断开插座和插头。移动电动包不能
够有效的额降低危险性。
禁止把两个充电器连接到一起。
充电器是为标准220V家用电器所设计的。不要试图在
其他电压下使用。对于车载充电器不适用。
充电器
您的工具适配得伟充电器。必须在使用前，详阅所有
安全注意事项。查阅后附目录找到电池包和充电器的
对 应 匹 配 表 。。
这些充电器无需任何调整，专为简易操作而设计。
充电步骤
1.在插入电池组之前，请把充电器插入合适的220V插
座中。
2.将电池包插入充电器中（如图1示），确保电池完全
放入充电器内。红（充电）灯会连续闪烁，表示充电过
程已经开始。
3.红灯保持持续发光时，表示充电已经完成。此时，
充满电的电池可供使用，也可留在充电器中。
注 意 ：为 确 保 锂 电 池 性 能 和 寿 命 最 大 化 ，首 次 使 用
前请将电池充满电。
充电过程
有关电池组的充电状态可参考下表
State of charge
电池充电中 –– –– –– ––
电池已充满 –––––––––––––––––
高／低温电池组
延迟充电
–– • –– • –– • –– •
x
电池或崇高电器故障 • • • • • • • • • • • •
电源电路故障 •• •• •• •• •• ••
本充电器不能给已经损坏的电池充电。充电器不亮、
闪烁类型为电池或充电器故障时，均可表示电池损
坏。
注意：这也可能表示充电器故障。
充电器显示故障时，请把充电器和电池组送往授权服
务中心检测。
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
