DeWalt DCS310 ユーザーマニュアル

DCS310

2

Copyright DeWALT

English (original instructions) 04

14

中文（繁體） 24

34

1

a

d

b

c

f

k

j

g

h

e

i

Figure 1

Figure 2

j

Figure 3

b

2

Figure 5

Figure 4

c

k

j

Figure 6

Figure 7

Figure 8

3

f

e

g

Figure 9A

Figure 10 Figure 11

Figure 12 Figure 13A

Figure 13B

Figure 9B

Figure 9C

English

4

10.8V CORDLESS PIVOT RECIPROCATING SAW

DCS310

Congratulations!

You have chosen a DeWALT tool. Years of

experience, thorough product development and

innovation make DeWALT one of the most reliable

partners for professional power tool users.

Technical Data

DCS310

Voltage V

DC

10.8

Type 1

Battery Type Li-Ion

Max. power output W 140

No-load speed min

-1

0–2700

Stroke length mm 14.3

Weight (without battery pack) kg 1.2

Battery pack DCB121 DCB123

Battery type Li-Ion Li-Ion

Voltage V

DC

10.8 10.8

Capacity A

h

1.3 1.5

Weight kg 0.2 0.2

Charger DCB100 DCB105

Mains voltage V

AC

220-240 220-240

Battery type Li-Ion Li-Ion

Approx. min 40 40 30 30

charging (1.3 Ah (1.5 Ah (1.3 Ah (1.5 Ah

time battery battery battery battery

packs) packs) packs) packs)

Weight kg 0.3 0.49

Deﬁnitions: Safety Guidelines

The definitions below describe the level of severity

for each signal word. Please read the manual and

pay attention to these symbols.

DANGER: Indicates an imminently

hazardous situation which, if not

avoided, will result in death or serious

injury.

WARNING: Indicates a potentially

hazardous situation which, if not

avoided, could result in death or

serious injury.

CAUTION: Indicates a potentially

hazardous situation which, if not

avoided, may result in minor or

moderate injury.

NOTICE: Indicates a practice not

related to personal injury which, if

not avoided, may result in property

damage.

Denotes risk of electric shock.

Denotes risk of fire.

WARNING: To reduce the risk of injury,

read the instruction manual.

General Power Tool Safety Warnings

WARNING! Read all safety warnings

and all instructions. Failure to follow

the warnings and instructions may result

in electric shock, fire and/or serious

injury.

Save all warningS and inStructionS

for future reference

The term “power tool” in the warnings refers to your

mains-operated (corded) power tool or battery-

operated (cordless) power tool.

1) WORK AREA SAFETY

a) Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of

flammable liquids, gases or dust. Power

tools create sparks which may ignite the dust

or fumes.

c) Keep children and bystanders away while

operating a power tool. Distractions can

cause you to lose control.

2) ELECTRICAL SAFETY

a) Power tool plugs must match the outlet.

Never modify the plug in any way. Do

not use any adapter plugs with earthed

(grounded) power tools. Unmodified plugs

and matching outlets will reduce risk of

electric shock.

b) Avoid body contact with earthed or

grounded surfaces such as pipes,

radiators, ranges and refrigerators. There

English

5

is an increased risk of electric shock if your

body is earthed or grounded.

c) Do not expose power tools to rain or wet

conditions. Water entering a power tool will

increase the risk of electric shock.

d) Do not abuse the cord. Never use the

cord for carrying, pulling or unplugging

the power tool. Keep cord away from

heat, oil, sharp edges or moving parts.

Damaged or entangled cords increase the

risk of electric shock.

e) When operating a power tool outdoors,

use an extension cord suitable for outdoor

use. Use of a cord suitable for outdoor use

reduces the risk of electric shock.

f) If operating a power tool in a damp

location is unavoidable, use a residual

current device (RCD) protected supply.

Use of an RCD reduces the risk of electric

shock.

3) PERSONAL SAFETY

a) Stay alert, watch what you are doing and

use common sense when operating a

power tool. Do not use a power tool while

you are tired or under the influence of

drugs, alcohol or medication. A moment of

inattention while operating power tools may

result in serious personal injury.

b) Use personal protective equipment.

Always wear eye protection. Protective

equipment such as dust mask, non-skid

safety shoes, hard hat, or hearing protection

used for appropriate conditions will reduce

personal injuries.

c) Prevent unintentional starting. Ensure

the switch is in the off position before

connecting to power source and/or

battery pack, picking up or carrying the

tool. Carrying power tools with your finger

on the switch or energising power tools that

have the switch on invites accidents.

d) Remove any adjusting key or wrench

before turning the power tool on. A

wrench or a key left attached to a rotating

part of the power tool may result in personal

injury.

e) Do not overreach. Keep proper

footing and balance at all times. This

enables better control of the power tool in

unexpected situations.

f) Dress properly. Do not wear loose

clothing or jewellery. Keep your hair,

clothing and gloves away from moving

parts. Loose clothes, jewellery or long hair

can be caught in moving parts.

g) If devices are provided for the connection

of dust extraction and collection facilities,

ensure these are connected and properly

used. Use of dust collection can reduce

dust-related hazards.

4) POWER TOOL USE AND CARE

a) Do not force the power tool. Use the

correct power tool for your application.

The correct power tool will do the job

better and safer at the rate for which it

was designed.

b) Do not use the power tool if the switch

does not turn it on and off. Any power

tool that cannot be controlled with the switch

is dangerous and must be repaired.

c) Disconnect the plug from the power

source and/or the battery pack from

the power tool before making any

adjustments, changing accessories, or

storing power tools. Such preventive safety

measures reduce the risk of starting the

power tool accidentally.

d) Store idle power tools out of the reach

of children and do not allow persons

unfamiliar with the power tool or these

instructions to operate the power tool.

Power tools are dangerous in the hands of

untrained users.

e) Maintain power tools. Check for

misalignment or binding of moving parts,

breakage of parts and any other condition

that may affect the power tool’s operation.

If damaged, have the power tool repaired

before use. Many accidents are caused by

poorly maintained power tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp

cutting edges are less likely to bind and are

easier to control.

g) Use the power tool, accessories and

tool bits etc., in accordance with these

instructions taking into account the

working conditions and the work to

be performed. Use of the power tool for

operations different from those intended

could result in a hazardous situation.

5) BATTERY TOOL USE AND CARE

a) Recharge only with the charger specified

by the manufacturer. A charger that is

suitable for one type of battery pack may

create a risk of fire when used with another

battery pack.

b) Use power tools only with specifically

designated battery packs. Use of any

other battery packs may create a risk of

injury and fire.

English

6

c) When battery pack is not in use, keep it

away from other metal objects like paper

clips, coins, keys, nails, screws or other

small metal objects that can make a

connection from one terminal to another.

Shorting the battery terminals together may

cause burns or a fire.

d) Under abusive conditions, liquid may be

ejected from the battery, avoid contact.

If contact accidentally occurs, flush with

water. If liquid contacts eyes, additionally

seek medical help. Liquid ejected from the

battery may cause irritation or burns.

6) SERVICE

a) Have your power tool serviced by a

qualified repair person using only identical

replacement parts. This will ensure that the

safety of the power tool is maintained.

Additional Safety Instructions for

Reciprocating Saws

 • Hold power tool by insulated gripping

surfaces when performing an operation

where the cutting accessory may contact

hidden wiring. Cutting accessory contacting a

“live” wire will make exposed metal parts of the

power tool “live” and could give the operator an

electric shock.

• ALWAYSwearadustmask.Exposure to

dust particles can cause breathing difficulty and

possible injury.

 • NEvER switch on the tool when the saw blade

is jammed in the workpiece or in contact with

the material.

 • Keephandsawayfrommovingparts. Never

place your hands near the cutting area.

 • Useextracautionwhencuttingoverhead

andpayparticularattentiontooverhead

wireswhichmaybehiddenfromview.

Anticipate the path of falling branches and

debris ahead of time.

• Do not operate this tool for long periods of

time. Vibration caused by the operating action

of this tool may cause permanent injury to

fingers, hands, and arms. Use gloves to provide

extra cushion, take frequent rest periods, and

limit daily time of use.

SWITCHING ON AND OFF

 • Afterswitchingoff,neverattempttostopthe

saw blade with your fingers.

 • Neverputthesawdownonatableorwork

bench unless switched off. The saw blade will

keep running briefly after the tool has been

switched off.

WHEN SAWING

 • Whenusingsawbladesspeciallydesignedfor

cutting wood, remove all nails and metal objects

from the workpiece before starting work.

 • Whereverpossible,useclampsandvicesto

fasten the workpiece securely.

 • Donotattempttosawextremelysmall

workpieces.

 • Donotbendtoofarforward.Makesure

that you always stand firmly, particularly on

scaffolding and ladders.

 • Alwaysholdthesawwithbothhands.

 • Forcuttingcurvesandpockets,useanadapted

saw blade.

CHECKING AND CHANGING THE SAW BLADE

 • Onlyusesawbladesconformingtothe

specifications contained in these operating

instructions.

 • Onlysharpsawbladesinperfectworking

condition should be used; cracked or bent saw

blades should be discarded and replaced at

once.

 • Ensurethatthesawbladeissecurelyfixed.

Residual Risks

In spite of the application of the relevant safety

regulations and the implementation of safety

devices, certain residual risks cannot be avoided.

These are:

– Impairment of hearing.

– Risk of personal injury due to flying particles.

– Risk of burns due to accessories becoming hot

during operation.

– Risk of personal injury due to prolonged use.

Markings on Tool

The following pictograms are shown on the tool:

Read instruction manual before use.

DATE CODE POSITION

The date code, which also includes the year of

manufacture, is printed into the housing surface that

forms the mounting joint between tool and battery.

Example:

2012 XX XX

Year of Manufacture

English

7

Important Safety Instructions for All

Battery Chargers

SAVETHESEINSTRUCTIONS: This manual

contains important safety and operating instruc tions

for the DCB100 and DCB105 battery chargers.

 • Beforeusingcharger,readallinstructionsand

cautionary markings on charger, battery pack,

and product using battery pack.

WARNING: Shock hazard. Do not allow

any liquid to get inside charger. Electric

shock may result.

CAUTION: Burn hazard. To reduce

the risk of injury, charge only DeWALT

rechargeablebatteries.Othertypesof

batteries may burst causing personal

injury and damage.

CAUTION: Children should be

supervised to ensure that they do not

play with the appliance.

NOTICE: Under certain conditions, with

the charger plugged in to the power

supply, the charger can be shorted by

foreign material. Foreign materials of

a conductive nature such as, but not

limited to, grinding dust, metal chips,

steel wool, aluminum foil, or any buildup

of metallic particles should be kept away

from charger cavities. Always unplug the

charger from the power supply when

there is no battery pack in the cavity.

Unplug charger before attempting to

clean.

 • DONOTattempttochargethebatterypack

with any chargers other than the ones in

this manual. The charger and battery pack are

specifically designed to work together.

 • Thesechargersarenotintendedfor

any uses other than charging DeWALT

rechargeable batteries. Any other uses

may result in risk of fire, electric shock or

electrocution.

 • Donotexposechargertorainorsnow.

 • Pullbyplugratherthancordwhen

disconnecting charger. This will reduce risk

of damage to electric plug and cord.

 • Makesurethatcordislocatedsothatit

will not be stepped on, tripped over, or

otherwise subjected to damage or stress.

 • Donotuseanextensioncordunlessit

is absolutely necessary. Use of improper

extension cord could result in risk of fire,

electric shock, or electrocution.

 • Donotplaceanyobjectontopofcharger

or place the charger on a soft surface that

might block the ventilation slots and result

in excessive internal heat. Place the charger

in a position away from any heat source. The

charger is ventilated through slots in the top and

the bottom of the housing.

 • Donotoperatechargerwithdamagedcord

or plug — have them replaced immediately.

 • Do not operate charger if it has received

a sharp blow, been dropped, or otherwise

damaged in any way. Take it to an authorised

service centre.

 • Donotdisassemblecharger;takeittoan

authorised service centre when service or

repair is required. Incorrect reassembly may

result in a risk of electric shock, electrocution or

fire.

 • Incaseofdamagedpowersupplycordthe

supply cord must be replaced immediately by

the manufacturer, its service agent or similar

qualified person to prevent any hazard.

 • Disconnectthechargerfromtheoutlet

beforeattemptinganycleaning.Thiswill

reduce the risk of electric shock. Removing

the battery pack will not reduce this risk.

• NEVERattempt to connect 2 chargers together.

 • Thechargerisdesignedtooperateon

standard220-240Vhouseholdelectrical

power. Do not attempt to use it on any other

voltage. This does not apply to the vehicular

charger.

Save tHeSe inStructionS

Chargers

The DCB100 and DCB105 chargers accept 10.8 V

Li-Ion batteries.

These chargers require no adjustment and are

designed to be as easy as possible to operate.

Charging Procedure (ﬁg. 2)

1. Plug the charger into an appropriate outlet

before inserting battery pack.

2. Insert the battery pack (j) into the charger.

The red (charging) light will blink continuously

indicating that the charging process has started.

3. The completion of charge will be indicated by

the red light remaining ON continuously. The

English

8

pack is fully charged and may be used at this

time or left in the charger.

NOTE: To ensure maximum performance and life of

Li-Ion batteries, charge the battery pack fully before

first use.

Charging Process

Refer the table below for the state of charge of the

battery pack.

State of charge

charging – – – –

fully charged –––––––––––

hot/cold pack delay –– – –– –

 replacebatterypack •••••••••••

Hot/Cold Pack Delay

When the charger detects a battery that is too hot

or too cold, it automatically starts a Hot/Cold Pack

Delay, suspending charging until the battery has

reached an appropriate temperature. The charger

then automatically switches to the pack charging

mode. This feature ensures maximum battery life.

LI-ION BATTERY PACKS ONLY

Li-Ion batteries are designed with an Electronic

Protection System that will protect the battery

against overloading, overheating or deep discharge.

The tool will automatically turn off if the Electronic

Protection System engages. If this occurs, place the

Li-Ion battery on the charger until it is fully charged.

Important Safety Instructions for All

Battery Packs

When ordering replacement battery packs, be sure

to include catalog number and voltage.

The battery pack is not fully charged out of the

carton. Before using the battery pack and charger,

read the safety instructions below. Then follow

charging procedures outlined.

read all inStructionS

 • Donotchargeorusebatteryinexplosive

atmospheres, such as in the presence of

flammable liquids, gases or dust. Inserting

or removing the battery from the charger may

ignite the dust or fumes.

• Never force battery pack into charger. Do

not modify battery pack in any way to fit into

a non-compatible charger as battery pack

may rupture causing serious personal injury.

 • ChargethebatterypacksonlyinDeWALT

chargers.

• DONOTsplash or immerse in water or other

liquids.

 • Donotstoreorusethetoolandbattery

pack in locations where the temperature

may reach or exceed 40 ˚C (105 ˚F) (such as

outside sheds or metal buildings in summer).

WARNING: Never attempt to open the

battery pack for any reason. If battery

pack case is cracked or damaged,

do not insert into charger. Do not

crush, drop or damage battery pack.

Do not use a battery pack or charger

that has received a sharp blow, been

dropped, run over or damaged in any

way (i.e., pierced with a nail, hit with a

hammer, stepped on). Electric shock

or electrocution may result. Damaged

battery packs should be returned to

service centre for recycling.

CAUTION: When not in use, place

tool on its side on a stable surface

where it will not cause a tripping or

falling hazard. Some tools with large

battery packs will stand upright on the

battery pack but may be easily knocked

over.

SPECIFIC SAFETY INSTRUCTIONS FOR LITHIUM ION

(Li-Ion)

 • Donotincineratethebatterypackevenifit

is severely damaged or is completely worn

out. The battery pack can explode in a fire.

Toxic fumes and materials are created when

lithium ion battery packs are burned.

 • Ifbatterycontentscomeintocontactwith

the skin, immediately wash area with mild

soap and water. If battery liquid gets into the

eye, rinse water over the open eye for

15 minutes or until irritation ceases. If medical

attention is needed, the battery electrolyte

is composed of a mixture of liquid organic

carbonates and lithium salts.

 • Contentsofopenedbatterycellsmaycause

respiratory irritation. Provide fresh air. If

symptoms persists, seek medical attention.

WARNING: Burn hazard. Battery liquid

may be flammable if exposed to spark

or flame.

Battery Pack

BATTERY TYPE

The DCS310 operates on a 10.8 volt battery pack.

Storage Recommendations

English

9

1. The best storage place is one that is cool and

dry away from direct sunlight and excess heat

or cold. For optimum battery performance and

life, store battery packs at room temperature

when not in use.

2. For long storage, it is recommended to store a

fully charged battery pack in a cool, dry place

out of the charger for optimal results.

NOTE: Battery packs should not be stored

completely depleted of charge. The battery pack will

need to be recharged before use.

Labels on Charger and Battery Pack

In addition to the pictographs used in this manual,

the labels on the charger and the battery pack show

the following pictographs:

Read instruction manual before use.

100%

Battery charging.

100%

Battery charged.

Battery defective.

Hot/cold pack delay.

Do not probe with conductive objects.

Do not charge damaged battery packs.

Use only with DeWALT battery packs,

others may burst, causing personal injury

and damage.

Do not expose to water.

Have defective cords replaced

immediately.

Charge only between 4 ˚C and 40 ˚C.

Discard the battery pack with due care for

the environment.

Do not incinerate the battery pack.

See Technical Data for charging time.

Only for indoor use.

Package Contents

The package contains:

1 Compact reciprocating saw

2 Li-Ion battery packs

1 Charger

1 Kit box

1 Instruction manual

NOTE: Battery packs and chargers are not included

with N-models.

 • Checkfordamagetothetool,partsor

accessories which may have occurred during

transport.

 • Takethetimetothoroughlyreadand

understand this manual prior to operation.

Description (ﬁg. 1)

WARNING: Never modify the power

tool or any part of it. Damage or

personal injury could result.

a. Trigger switch

b. Lock-off button

c. Pivot release slider

d. Shoe

e. LED worklight

f. Blade clamp

g. Blade clamp release lever

h. Main handle

i. Hand grip

j. Battery pack

k. Battery pack release button

INTENDED USE

This reciprocating saw is designed for professional

cutting of wood, metal, plastic and drywall.

DO NOT use under wet conditions or in presence of

flammable liquids or gases.

This reciprocating saw is a professional power tool.

DO NOT let children come into contact with the

tool. Supervision is required when inexperienced

operators use this tool.

English

10

 • Thisproductisnotintendedforusebypersons

(including children) suffering from diminished

physical, sensory or mental abilities, or for lack

of experience and/or for want of knowledge or

skills unless they are supervised by a person

responsible for their safety. Children should

never be left alone to play with this product.

Electrical Safety

This tool is double insulated; therefore no

earth wire is required. Always check that the power

supply corresponds to the voltage on the rating

plate.

If the supply cord is damaged, it must be replaced

by the manufacturer or an authorised Black &

Decker Service Centre in order to avoid a hazard.

Using an Extension Cable

An extension cord should not be used unless

absolutely necessary. Use an approved extension

cable suitable for the power input of your charger

(see Technical Data). The minimum conductor size

is 1 mm

2

; the maximum length is 30 m.

When using a cable reel, always unwind the cable

completely.

ASSEMBLY AND ADJUSTMENTS

WARNING: Prior to assembly and

adjustment, always remove the battery

pack. Always switch off the tool before

inserting or removing the battery pack.

WARNING: Use only DeWALT battery

packs and chargers.

Installing and Removing the Battery

Pack (ﬁg. 5)

WARNING: To reduce the risk of injury,

never depress the battery release button

without removing the battery pack.

Depressing the battery release button

without removing the battery pack can

result in the battery pack falling out

unexpectedly.

NOTE: Make sure your battery pack (j) is fully

charged.

TO INSTALL THE BATTERY PACK INTO THE TOOL HANDLE

1. Align the battery pack with the rails inside the

handle.

2. Slide it firmly into place until you hear the lock

snap into place.

TO REMOVE THE BATTERY PACK FROM THE TOOL

1. Press the release button (k) and firmly pull the

battery pack out of the tool handle.

2. Insert battery pack into the charger as

described in the charger section of this manual.

Variable Speed Trigger Switch (ﬁg.1)

To turn the tool on, squeeze the variable speed

trigger switch (a). To turn the tool off, release the

variable speed trigger switch.

The trigger switch enables you to start the

application at a slow speed. The further you depress

the trigger, the faster the tool will operate.

WARNING: This tool has no provision

to lock the switch in the on position and

should never be locked on by any other

means.

LOCK-OFF BUTTON

Your saw is equipped with a lock-off button (b).

To lock the trigger switch (a), press the lock-off

button as shown in figure 3. When the lock-off

button is depressed to the lock icon, the tool is

locked. Always lock the trigger switch when carrying

or storing the tool to eliminate unintentional starting.

NOTICE: Use of very slow speed is

recommended only for beginning a cut.

Prolonged use at very slow speed may

damage your saw.

OPERATION

Instructions for Use

WARNING: Always observe the safety

instructions and applicable regulations.

WARNING: Toreducetherisk

of serious personal injury, place

thelock-offbuttoninthelock-

off position or turn tool off and

disconnectbatterypackbefore

makinganyadjustmentsor

removing/installingattachmentsor

accessories. An accidental start-up

can cause injury.

Proper Hand Position (ﬁg. 1, 4)

WARNING: To reduce the risk of

serious personal injury, ALWAYS use

proper hand position as shown.

English

11

WARNING: To reduce the risk of

serious personal injury, ALWAYS hold

securely in anticipation of a sudden

reaction.

Proper hand position requires one hand on the

hand grip (i), with the other hand on the main handle

(h). Hand orientation is dependent upon user’s

preference.

Pivot Release Slider (ﬁg. 3, 6, 7)

WARNING: To avoid tool being turned

on accidentally, make sure the lock-off

button (b) is engaged.

WARNING: To avoid being pinched,

keep hands away from the hinge when

changing positions.

The tool can be converted into three different

positions. To change positions, slide the pivot

release slider (c) to the right as shown in Figure6

and rotate the handle portion of the tool until it

snaps securely into any of the three positions shown

in Figure 7.

Blade Installation and Removal

(ﬁg.8, 9A, 9B, 9C)

WARNING: Toreducetherisk

of serious personal injury, place

thelock-offbuttoninthelock-

off position or turn tool off and

disconnectbatterypackbefore

makinganyadjustmentsor

removing/installingattachmentsor

accessories. An accidental start-up

can cause injury.

Different blade lengths are available. Use the

appropriate blade for the application. The blade

should be longer than 3-1/2" (89 mm) and should

extend past the shoe and the thickness of the

workpiece during the cut. A 4" (102 mm) blade is

recommended for best performance. Do not use

jigsaw blades with this tool.

WARNING: Cut hazard. Blade breakage

may occur if the blade does not extend

past the shoe and the workpiece during

the cut (fig.8). Increased risk of personal

injury, as well as damage to the shoe

and workpiece may result.

TO INSTALL BLADE INTO SAW (FIG. 9A, 9B, 9C)

1. Pull blade clamp release lever (g) up.

2. Insert the blade shank into the blade clamp

(f,fig. 9C).

3. Close blade clamp release lever.

4. Note that the blade can be installed upside-

down to assist in flush-to cutting (refer to

fig.9B).

TO REMOVE BLADE FROM SAW (FIG. 9A, 9B, 9C)

CAUTION: Burn hazard. Do not touch

the blade immediately after use. Contact

with the blade may result in personal

injury.

1. Pull blade clamp release lever (g) up.

2. Remove blade.

Worklight (ﬁg. 9C)

The worklight (e) is located below the blade clamp

(f) behind the shoe. The worklight will be activated

when the trigger switch is squeezed.

NOTE: The worklight is for lighting the immediate

work surface and is not intended to be used as a

flashlight.

Cutting (ﬁg. 9B, 10–13)

WARNING: Always use eye protection.

All users and bystanders must wear eye

protection that conforms to ANSI Z87.1.

WARNING: Exercise extra caution

when cutting towards operator. Always

hold saw firmly with both hands while

cutting.

Before cutting any type of material, be sure it is firmly

anchored or clamped to prevent slipping. Place

blade lightly against work to be cut, switch on saw

motor and allow it to obtain maximum speed before

applying pressure. Whenever possible, the saw shoe

must be held firmly against the material being cut.

This will prevent the saw from jumping or vibrating

and minimize blade breakage. Any cuts which put

pressure on the blade such as angle or scroll cuts

increase potential for vibration, kickback and blade

breakage.

WARNING: Use extra caution when

cutting overhead and pay particular

attention to overhead wires which may

be hidden from view. Anticipate the path

of falling branches and debris ahead of

time.

WARNING: Inspect work site for hidden

gas pipes, water pipes or electrical wires

before making blind or plunge cuts.

Failure to do so may result in explosion,

property damage, electric shock, and/or

serious personal injury.

FLUSH-TO CUTTING (FIG. 9B, 10)

The compact design of the saw motor housing and

spindle housing permits extremely close cutting to

English

12

floors, corners and other difficult areas. The blade

should be inserted upside-down to assist in flush-

cutting (fig.9B).

POCKET/PLUNGE CUTTING – WOOD ONLY (FIG. 11)

The initial step in pocket cutting is to measure the

surface area to be cut and mark clearly with a

pencil, chalk or scriber. Use the appropriate blade

for the application. The blade should be longer than

3-1/2" (89mm) and should extend past the shoe

and the thickness of the workpiece during the cut.

A 4" (102mm) blade is recommended for best

performance. Insert blade into the blade clamp.

Next, tip the saw backward until the back edge

of the shoe is resting on the work surface and the

blade clears the work surface. Then, squeeze the

trigger switch and allow saw to come up to speed.

Grip saw firmly with both hands and begin a slow,

deliberate upward swing with the handle of the saw,

keeping the bottom of the shoe firmly in contact with

the workpiece. Blade will begin to feed into material.

Always be sure blade is completely through material

before continuing with pocket cut.

NOTE: In areas where blade visibility is limited, use

the edge of the saw shoe as a guide. Lines for any

given cut should be extended beyond edge of cut

to be made.

METAL CUTTING (FIG. 12)

Your saw has different metal cutting capacities

depending upon type of blade used and the metal

to be cut. Use a finer blade for ferrous metals and a

coarse blade for non-ferrous materials. In thin gauge

sheet metals it is best to clamp wood to both sides

of sheet. This will ensure a clean cut without excess

vibration or tearing of metal. Always remember not

to force cutting blade as this reduces blade life and

causes costly blade breakage.

NOTE: It is generally recommended that when

cutting metals you should spread a thin film of oil or

other lubricant along the line ahead of the saw cut

for easier operation and longer blade life.

HORIZONTAL/VERTICAL SAW MODES (FIG. 13)

The saw can be used in either of the modes shown.

Horizontal Mode: Blade teeth face downward as

shown in figure13A.

Vertical Mode: Blade teeth face forward as shown

in figure 13B.

The DCS310 can accept all lengths of reciprocating

blades. For best results use 4" (102 mm) blades.

Ensure the blade extends past the shoe and the

thickness of the workpiece during the cut. Use a

longer blade if needed. Whenever possible, the

saw shoe must be held firmly against the material

being cut. This will prevent the saw from jumping or

vibrating and minimize blade breakage.

MAINTENANCE

Your DeWALT power tool has been designed to

operate over a long period of time with a minimum

of maintenance. Continuous satisfactory operation

depends upon proper tool care and regular cleaning.

WARNING: Toreducetherisk

of serious personal injury, place

thelock-offbuttoninthelock-

off position or turn tool off and

disconnectbatterypackbefore

makinganyadjustmentsor

removing/installingattachmentsor

accessories. An accidental start-up

can cause injury

The charger and battery pack are not serviceable.

There are no serviceable parts inside.

Lubrication

Your power tool requires no additional lubrication.

Cleaning

WARNING: Blow dirt and dust out of

the main housing with dry air as often as

dirt is seen collecting in and around the

air vents. Wear approved eye protection

and approved dust mask when

performing this procedure.

WARNING: Never use solvents or

other harsh chemicals for cleaning the

non-metallic parts of the tool. These

chemicals may weaken the materials

used in these parts. Use a cloth

dampened only with water and mild

soap. Never let any liquid get inside the

tool; never immerse any part of the tool

into a liquid.

CHARGER CLEANING INSTRUCTIONS

WARNING: Shock hazard. Disconnect

the charger from the AC outlet before

cleaning. Dirt and grease may be

removed from the exterior of the charger

using a cloth or soft non-metallic brush.

Do not use water or any cleaning

solutions.

English

13

Optional Accessories

WARNING: Since accessories, other

than those offered by DeWALT, have

not been tested with this product, use

of such accessories with this tool could

be hazardous. To reduce the risk of

injury, only DeWALT, recommended

accessories should be used with this

product.

Consult your dealer for further information on the

appropriate accessories.

Protecting the Environment

Separate collection. This product must

not be disposed of with normal

household waste.

Should you ﬁnd one day that your DeWALT product

needs replacement, or if it is of no further use to you,

do not dispose of it with household waste. Make this

product available for separate collection.

Separate collection of used products and

packaging allows materials to be

recycled and used again. Re-use of

recycled materials helps prevent

environmental pollution and reduces

the demand for raw materials.

Local regulations may provide for separate collection

of electrical products from the household, at

municipal waste sites or by the retailer when you

purchase a new product.

DeWALT provides a facility for the collection and

recycling of DeWALT products once they have

reached the end of their working life. To take

advantage of this service please return your product

to any authorised repair agent who will collect them

on our behalf.

You can check the location of your nearest

authorised repair agent by contacting your local

DeWALT office at the address indicated in this

manual. Alternatively, a list of authorised DeWALT

repair agents and full details of our after-sales

service and contacts are available on the Internet at:

www.2helpU.com.

Rechargeable Battery Pack

This long life battery pack must be recharged when

it fails to produce sufficient power on jobs which

were easily done before. At the end of its technical

life, discard it with due care for our environment:

 • Runthebatterypackdowncompletely,then

remove it from the tool.

 • Li-Ioncellsarerecyclable.Takethemtoyour

dealer or a local recycling station. The collected

battery packs will be recycled or disposed of

properly.

14

10.8V

DCS310

V

DC

10.8

1

140

min

-1

0-2700

mm 14.3

() kg 1.2

DCB121 DCB123

V

DC

10.8 10.8

A

h

1.3 1.5

kg 0.2 0.2

DCB100 DCB105

V

AC

220 V 220 V

40 40 30 30

(1.3 Ah (1.5 Ah (1.3 Ah (1.5 Ah

) ) ) )

kg 0.3 0.49

/

指由市电驱动时（

有线）电动工具，或由电池驱动时（无线）电动工

具。

1)

a)

b)

c)

2)

a)

b)

15

c)

d)

e)

f)

(RCD)

3)

a)

b)

c)

d)

e)

f)

g)

4)

a)

b)

c)

d)

e)

f)

g)

5)

a)

b)

c)

d)

16

e)

6)

a)

 •

–

2012 XX XX

DCB100

DCB105



17

 •

—

 •

•

 •

220

DCB100 DCB105 10.8 V

( 2)

1.

2. (j)

3.

18

–– –– –– ––

–––––––––––––––––

/ ––– –– ––– ––

• • • • • • • • • • • •

/

 •

•

 •

•

 •

40°C

(

105°F

)

 •

15

 •

DCS310 10.8

1.

ページが読み込まれています...

DeWalt DCS310 ユーザーマニュアル

DeWalt DCS310 ユーザーマニュアル

他の言語で

関連論文

その他のドキュメント