USER MANUAL
FULLY AUTOMATIC WASHING MACHINE
Model SF-S55GR
Thank you for your purchase of
Fully Automatic Washing Machine.
Please read this manual carefully for proper
operation.
Please keep this manual for future reference.
2
CONTENTS
Preface ........................................................................................................................... 3
Safety Precautions ................................................................................ 4
Installation Guide .................................................................................................... 7
Installation .................................................................................................................... 12
Safety Check
........................................................................................................... 13
Washing Machine Repair
............................................................................... 13
Control Panel ........................................................................................................ 14
Technical Description ........................................................................................ 16
Before Using Your Machine ............................................................................. 17
Checking Amount of Laundry and Detergent (Approximately Amount)
( ) .......................................................................................... 18
How to Use Liquid Detergent, Bleach and Fabric Softener
..................................................................................... 19
Amount of Laundry and Detergent ......................................................... 21
Selection of Laundry Process ............................................................. 22
NORMAL Process ................................................................................................ 23
HEAVY Process ................................................................................................... 25
SPEEDY Process ................................................................................................. 27
SOAK Process ...................................................................................................... 28
SILK Process ........................................................................................................ 30
BLANKET Process ................................................................................................ 34
Using the Washing Cap ..................................................................................... 37
Content of the Washing Process ................................................................ 39
PRESET 9 HR Process 9 .......................................................................... 40
Decreasing Drying Time ("Powerful Dehydration") .................... 41
Wash in Your Favorite Way ...................................................... 42
Use the Detergent Again ............................................................................ 44
Lid Lock Function ........................................................................................... 44
Use Guidelines ....................................................................................... 45
Switch Off the Buzzer Beep After the Completion Of the Washing Process .......
45
Maintenance and Repair ................................................................................ 46
When Failure Happens .................................................................................. 50
Optional Parts ....................................................................................................... 56
Product Specifications .......................................................................................... 56
3
Preface
The number next to the sign is the page number for detailed description.
Infiltration washing
Infiltrate the detergent inside the cloth to detach the dirt off the cloth fiber.
The detergent dissolves sufficiently to become the high-concentration detergent that washes the
laundry in infiltration mode for easier detachment of dirt off the cloth fiber.
Please use concentrated powder detergent to wash.
The infiltration washing can't be performed to the processes of "SILK", "BLANKET" and "BASKET CLEAN". (Because of
no detergent dissolution course in these processes)
( )
11)
Put detergent in
The detergent put in at the
injection opening will fall
below the pulsator.
2)
Supply a little water
3)
The detergent dissolves inside the
cloth
The concentrated detergent dissolves
with the power agitating of pulsator,
and infiltrates sufficiently inside the
cloth.
2,3,4
THREE-STEP washing
Inject a little water, and the
dirt will detach with the
high-concentration
detergent; inject more
water to the normal water
level for washing.
Detergent injection
opening
Outer basket
Pulsator
Stainless-steel basket
The laundry rearrangement may be out of service in the case that the washing capacity is more than 4kg.
4kg
The laundry rearrangement doesn't perform in the case of manual setup of "RINSE", "SPIN" or "SPIN
ONLY".
Laundry rearrangement and spinning
Loosen the post-spinning laundry for easy taking out.
4
Safety Precautions
Please read this part of substance carefully for proper operation before using your machine.
The precautions stated here are classified as "Warning" and "Attention" according to the damage and the emergency
caused by misoperation, and are described respectively in line with the marks below.
With no respect to this mark, the misoperation may cause death or GBH.
With no respect to this mark, the misoperation may cause body harm or object damage.
This mark indicates the content of warning or attention.
This mark indicates the prohibited action.
This mark indicates the compulsory action to be carried out.
Graphic mark
Dismantle, repair or alterations should
only carried out by professional
technicians.
Avoid electric shock, fire, and body injury due to
improper activity.
This washing machine is equipped
with the electricity wire with bi-
electrode grounding plug, please use
the bi-electrode grounding socket.
The creepage protector shall be used
if possible.
To prevent electricity leak which may cause injuries.
Electricity supply must be unplugged
with dry hands.
Otherwise, this may cause electric shock.
Please use the single socket with
220V, 10A specification.
220V 10A
The share of the same socket with
other electric appliances may cause
fire due to excessive heat.
Washing machine should not be
installed in humid place or in places
exposed to wind and rain.
Otherwise, electricity leak causing electric shock or fire may occur.
Do not put water in direct contact with
the unit during maintenance and repair.
This may cause short circuit or electric shock.
Dismantling
Prohibited
Grounding
Wet hands
Prohibited
Power
Humid places
prohibited
Prohibited
Warning
Attention
Warning
5
Prohibited
Prohibited
Clear
Do not put your hand into the basket
until it has stopped completely.
Even when the spinning of the basket
is slow, there is still a danger of being
caught in the motion, resulting injuries.
Particular attention should be paid
when children are around.
Damaged or loosen wire or plug
should not be used.
Keep child away from the washing
spinning basket and do not place box
or shelves next to the washing machine.
Children may fall into the
basket resulting in injuries.
Otherwise electric shock, short circuit or fire may take
place.
Do not put your hands into the
washing • spinning basket during the
washing and rinsing process.
Even when the spinning is slow, hands may be trapped by
clothes. If necessarily, please press pause button, and put
your hands into the basket after it has stopped completely.
(
)
Do not damage wire.
Do not damage or alter the wire
forcibly bend, pull, twist or handle
the wire. Beside, please do not
put weigh on or trap the wire.
Damage of wire may case electric shock or fire.
Thoroughly wipe the power plug
when dirt is adhering the prong or
around the base of the prong.
Failure to do so may cause a fire.
To prevent fire or explosion which may cause injuries.
Do not put gasoline, benzine,
alcohol, thinner of fabrics with
these stains into or near to the
washing machine.
Prohibited
Prohibited
Prohibited
Prohibited
This washing machine is strictly
prohibited to get close to the
locations with candle, mosquito-
repellent incense, dog-end or
other kinds of open flame.
No smoke or fire
To avoid injuries caused by the lock damage.
Warning
6
Do not open the lid in locked status by force.
Prohibited
Otherwise, the lid or locking device may
be damaged, resulting in unstoppable
spinning of washing • spinning basket
and thus causing injuries.
Safety Precautions (continued)
( )
Do not pull the wire from the socket
when unplugging the unit.
To avoid electric shock or fire cause by short
ciruit may result.
Do not connect to the hot water supply.
And, water of above 50
o
C should not be
used for washing.
50
o
C
Electric shock or leakage may occur
due to deformation of plastic parts of
the unit.
Please unplug the unit when not using
the unit for a long period of time.
Electric shock or leakage due to aging of insulator may
cause fire.
Water supply hose should be tightly
screwed to the unit.
Failure to do so may result in water leakage.
Used for a long period of time, the unit may
result in water leakage caused by loosen
union nut. So please check it in time and
screw tightly again.
Check water supply hose connection
by turning on the water before
washing.
To prevent damages caused by possible water leakage
due to loosen screw.
Do not stand on or put weight on the
top of the unit.
Otherwise, deformation and damage
may result causing injuries.
Ports in motion beneath the
unit may cause injuries.
Keep hands and feet away from the
button of the washing when it is motion.
Electricity supply must be unplugged
with dry hands during maintenance
and repair.
Otherwise, electric leakage causing
injuries may occur.
Prohibited
When installing the washing machine,
be sure to draw out the water drainage
hose until the the black and purple
mark is seen.
Failure to do so may cause friction leading to damage.
Prohibited
Prohibited
Prohibited
water
leakage
water
leakage
water
leakage
Warning
Attention
Do not insert a screwdriver into the Lid
Lock hold.
Prohibited
To avoid injuries caused by the lock damage.
7
Installation of Washing Machine
Please install on a solid horizontal
surface.
Installation on a slippy or irregular surface
may result in noise and shaking.
The unit should be installed on a flat horizontal surface.
Otherwise sudden stop or abnormal sound may result during the spinning cycle.
Avoid installing the unit too close to the
wall.
This is to prevent abnormal vibration and noise.
Safety Precautions (continued)
( )
Where to install
Solid, horizontal surface Weak surface Irregular surface
How to install
At least 1.5cm
1.5cm
At least 1.5cm
1.5cm
At least 9cm(Water Drainage hose onside)
9cm ( )
Installation Guide
Do not wash, rinse and spin the water
proof fabric or cloth.
sleeping bag, raincoat, cover of skiing, utilities,
bicycles, cars and motors
Prohibited
Otherwise may lead to injury by abnormal vibration during spinning
or damage the washing machine, wall, floor and clothes.
Attention
Please turn off the water tap when not
using the unit.
To prevent damages caused by water
leakage.
water
leakage
( )
Do not incline installing the washing cap. Do not use the washing cap except
"
SILK
"
process,
"
BLANKET
"
process.
Prohibited
Splash of water may occur or washing cap may be swung out of the basket.
8
Installation Guide (continued)
( )
Installation of Washing Machine
1
Adjust the instability of the washing
machine with adjustable leg.
2
Please make sure of the horizontality of the
washing machine.
As shown in the figure, the horizontality can be easily
observed by the string used to hang an object.
Fixed leg
Adjustable leg
It is level if the
clearance between A
and machine body is
the same with that
between a and the
machine body.
A
string
A
A
object
(front or
profile)
Put some water into the washing barrel and reconfirm its
horizontality.
The ground is level if all front, rear, left and right height difference between
the spinning hole and water surface are less than 3mm.
(B C ) 3mm
To install the machine on an inclined floor, leg caps in the attached accessory kit can
be used to adjust height by connecting them to the fixed leg.
Inspection of trial run
How to Use the Adjustable Leg
1
Loosen the lock nut by unscrewing in
arrow direction 1 before using the
adjustable leg to stabilize unit.
1
2
After adjusting of the unit, tighten
the lock nut by screwing it in arrow
direction.
2
Lowering
Loosening
Lock nut
Adjustable leg
Elevating
Maximum adjust able
range is 40mm.
Tightening
Lock nut
Plastic base
Tighten the lock nut until it reaches the plastic base.
At most 40mm
40mm
9
How to Change the Water Drainage Hose and How to Install the Base Plate
When fitting the water drainage hose to the
water drainage outlet
If the water drainage outlet is too shallow
or the end of the water drainage hose
touches the grounds, cut the end of the
water drainage hose in an oblique angle.
Water drainage hose which inserts into the unit, can 't
touch other parts, to prevent the damage caused by
water leakage.
The black or purple mark of the water
drainage hose should be inserted into the
corresponding groove of the unit.
Water drainage hose retainer must be tightened.
The inner section of the water drainage hose must be
secured by the retainer before fetched out.
Failure to do so may cause
insufficient rinsing or unit
malfunction due to poor drainage
or too much subbles during rinsing
and spinning.
Attention
Attention
Water
drainage hose
Water
drainage outlet
Water drainage hose is attached on the left side of unit at shipment, nonetheless, it can be
reattached on the right side to suit drainage needs.
2Purple mark
Water drainage hose outlet
3Hose retainer
1Drainage hose cover
Back
Black mark
Front
The water drain-
age hose pulled
out (right)
The water drain-
age hose pulled
out (left)
The water
drainage hose
Corrugate
paper etc.
1
Lay the unit down slowly.
Lay the unit down on some corrugate pqper to
prevent damage.
2
Pull out the water drainage hose from
the right side of the unit.
1 Remove the right water drainage hose cove
(The cover can be disposed).
2 After pulling out the Black mark of the
water drainage hose from the left groove of
the unit , the Purple mark of the water
drainage should be inserted into the
corresponding groove of the right unit.
3 The water drainage hose should be pulled out
through the proper hose retainer when the hose
is pulled out on the right.
10
How to install the base plate (Mount the base plate on the pad on top of
unit)
( )
Fit the barb on the plate into the square hole of the bottom, and tighten the screws.
Installation Guide (continued)
( )
Water Drainage Hose Related Parts
How to Install the Water Supply Hose
Extended hose
Please use optional extension drainage tube for
lengthening the water drainage hose.
Ensure that the drainage hose will not separate from its outlet even if there is vibration or the
outlet is too big or too shallow.
Follow the instructions below to improve drainage efficiency.
The method of pulling out the water drainage
hose as shown below should be avoided.
Otherwise, water leakage or abnormal sound
may occur.
When purchasing extension hose, make sure that the inner diameter of the hose is big enough, otherwise, poor
drainage may cause and result in the malfunction of the unit.
Firmly tighten the union nut when
connecting the water supply
hose to the main unit.
Loosely tightened union nut will cause water leakage.
When removing the hose, unscrew the union nut first.
Please use optional extension tube for
lengthening the water supply hose.
Three standard of extension hoses (1m,2m,3m) are
available.Please inquire distributors for extending
the water supply hose.
1m 2m 3m
Length of water drainage hose
should not exceed 5m.
5m
Extension drainage hose
Height of water drainage hose should
not exceed 15cm and length should
not exceed 2m.
15cm
2m
Less than 5m
5m
Less than 2m
2m
Less than 15m
15m
Attention
Connecting the water supply hose to the main unit
Extended the water supply hose
11
How to Install the One Touch Joint
1
Confirm the diameter of the water tap.
Distance must be over 1.6cm
in order to install correctly.
1.6cm
May break off after install
the one touch joint.
Water leakage may
occur.
If the diameter exceeds 2cm, remove
the joint ring.
2cm
Screw joint B in the arrow direction to
adjust the gap.
B
For water supply hose installation, please refer to "How to install water supply hose" in the user manual.
Loosening may occur with extended use. In such case, reinstall the joint following steps 2 to 4.
2 ~ 4
(Carry out the same steps when reinstalling the one touch joint at a change of residence, etc.)
( )
Horizontal tap A
A
Horizontal tap B
B
Square mouth tap Universal household tap Swivel tap
2
34
Tighten joint B in the arrow direction
to reduce the gap between joint A
and B to 4mm or less.
B A B
4mm
Screw
Label
One touch joint
Joint ring
Check the distance between
joints A and B.
A B
Joint
Approximately 6
Joint
6
Press the sealed pad evenly against the
tap and tighten the four screws in a uniform
fashion.
4
Tighten screw in advance if it is
located close to the wall.
Water tap
Sealed pad
Joint
Joint
Joint
(After tighten)
Less than 4
4
Appropriate water tap
Horizontal taps A and B as shown below.
A B
12
1
3
2
2
1
Please turn on the water tap to check to connecting condition of the water supply hose
before washing.
To prevent damages caused by water leakage due to loosen screw.
How to install and remove the water supply hose
Water tap
Do not allow water tap, one touch joint and rubber
ring to touch the unit when installing them.
Installing
Push down the rubber ring
and insert the tap into the
one touch joint.
Release the rubber ring and
push up the water supply
hose until it clicks.
Pull the water supply hose to
check that it does not come
off easily.
Removing
Turn off the water tap.
Press the "START" button and let the unit run for
about ten seconds.
10
This is to prevent water splash when removing the tap.
Remove the latch and the water supply hose while
pushing down the rubber ring.
Loosely tightened union nut will cause water
leakage.
When removing the hose, unscrew the union
nut first.
Please note that water supply hose and one
touch joint should be used.
Turn the union nut in the direction as shown
by the arrow and firmly. Connect it to the
water supply opening.
Firmly tighten the union nut when con-
necting the water supply hose to the main
unit.
Failure to do so may result in water
leakage.
Installation
Attention
Attention
One touch joint
Latch
Latch
Water supply hose
Rubber ring
Rubber ring
Turn off
Attention
Main unit
The appliance is to be connected to the water
mains using new hose-sets and that old hose-
sets should not be reused.
13
Safety Check
If any of the following conditions or other abnormalities occur, immediately pull out the power plug
to prevent an accident and request help from an authorized dealer or agent.
, , (
)
Never conduct repairs by yourself as it may be dangerous.
,
If you have used the washing machine for 4 - 5 years,even if the following conditions and other abnormalities do not occur, request
for safety inspection of the machine is stilled required.
4 ~ 5 , ,
If the power supply cord is damaged, Please repair it in a repair shop appointed by the manufacturer or its service agents in order
to avoid a hazard.
The washing machine is not to be used by children or persons with reduced physical , sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision or instruction.
The washing machine having ventilation openings in the base.
The washing machine bottom must not be obstructed by carpeting when the washing machine is installed on a carpet floor.
When you turn on the switch, the machine sometimes does
not operate.
The power cord has cracks or flaws .
There are abnormal sounds and vibrations during operation.
The agitator does not stop easily. ( It takes over 15 seconds
for the agitator to stop )
( 15 )
There is water leakage. (Basket,hose, joint,etc. )
( )
There is a smell of burning.
If you touch the machine, you may get an electric shock.
,
In case when the washing machine is used in places other than ordinary households.
If the washing machine is in use for extremely long periods of time compared to ordinary household usage, such as in dormitories
and hospitals,it may be necessary to change parts(such as the clutch,belt or sealed pad) more frequently.In this case,consult with
the dealer from whom you purchased the washing machine and have the machine inspected periodically.
, , ( )
,
Washing Machine Repair
In case of malfunction of the washing machine, read the manual in detail before requesting repair
services. If the the problem still cannot be solved, contact an authorized service dealer or a service
agent and provide the following information.
1 Model name: SF-S55GR.
2 Describe abnormal situations and damages in detail.
3 Your address and telephone number.
, ,
,
1 SF-S55GR
2
3
14
Control Panel
Never press 2 (or more) buttons together, which may cause misoperation.
2 ( 2 )
Used to set the water level manually
or replenish water during the agitating.
¡After the washing machine starts, any
change of setup shall be made before
the end of washing and rinsing. Before
making the change, please press the
"PAUSE" button. (During the course
from starting the water supply to
reaching the required level, the setup
can't be changed)
ઢ
¡
Press and hold the "WATER LEVEL"
button to replenish water during the
course of washing or rinsing. (No water
will be replenished after reaching the
top water level of each process)
WATER LEVEL button
Used to set the processes of washing,
rinsing or spinning manually or
change the setup.
¡After the washing machine starts, the
setup can't be changed.
༜Ϸ܃
MANUAL button
The detergent amount and the water level are described by
the lighting or flashing of indicator. The amount of detergent
refers to the (concentrated) powder detergent. 21
21
Detergent indicator
The indicators of washing, rinsing and spinning display
the ongoing process.
¡During the washing machine operation, the display (lighting,
flashing, darkening) of indicator of each process describes
the operation status and the working process to the user.
Washing indicator
Displays either [30
min] or [60 min],
indicator lamp will
light for [30 min],
and will flash for
[60 min].
30 60
30
60
Can be set when
using the [Normal]
[Heavy] [Speedy]
[Soak] [Blanket]
[Preset 9hr] process.
Basket Air Jet can
also be set.
41
41
Powerful Dehydration indicator
POWERFUL DEHYDRATION button
15
In the case of any of the following manual setup, the washing machine will make 2 sounds for acceptance (to announce the datum
mark of indication):
2 ( )
1 The water level is "50L"; 2The washing manual is "Wash+Rinse+Spin"; 3 The process is "NORMAL"; 4 Powerful Dehydration
is "No setup".
1 50L 2 + + 3 4
There are eight options available, you
can choose the right one based on
the types and dirty levels of the
washings . 22
8
22
¡By pressing the "PROGRAM" button,
the indicator of the selected process
will light or flash.
PROGRAM button
The button is used to start the
operation or temporarily pause the
operation.
ઢ
¡After selecting the required process,
press this button to start or pause the
process operation.
ઢ
¡If press the "Pause" button during the
course of spinning, no button signal
can be received until the switching off
the power, and the lid can't be opened.
START/PAUSE button (One touch button)
ઢ
Used to "switch on" and "switch off"
the power.
¡When the washing cycle finishes,the
buzzer beeps and the power of the
unit will be switched off automatically.
The washing machine will be
automatically switched off after 5
minutes of no start with power on.
53
ઢ
5
53
POWER switch
Lid Lock indicator will light when the lid is in locked status.
¡Before the water supply, the lid is in the status of locking.
Lid Lock indicator
The indicator of selected process will light or flash.
With each pressing on the "PROGRAM" button, the
indicator will light in the following sequence.
Programme indicator
9
NORMAL
Light
SOAK
Light
HEAVY
Light
SPEEDY
Light
BLANKET
Flash
PRESET 9HR
Flash
BASKET CLEAN
Flash
SILK
Flash
16
Technical Description
The number next to the sign is the page number for detailed description.
Accessories (Refer to Installation Guide ) ( )
One touch joint
(One)
(1 )
Base plate
(Screws include)
( )
(One)
(1 )
Water supply hose
(One)
(1 )
Leg cap
(Two)
(2 )
17
The laundry from which the
hair or silk is inclined to run
shall have its inner side turn
to external before washing.
Please remove soil or dirt
from laundry before
washing.
Remove anything from the
laundry before washing.
(Do not forget anything in
pocket)
( )
• To avoid damaging the clothes
and unit malfunction.
Before Using Your Machine
Preparation for washing machine
Remove matches, hairpins or
coins etc. from laundry.
Preparation for laundry
When the first using
The washing machine can be used only after the proper installation in compliance
with the "Installation Guide".
Daily using
The front of the water drainage hose must insert in the drainage outlet.
Connect the water supply hose and turn on the water tap.
Insert the power plug into the socket.
1
2
3
Water supply hose
AC 220V
220V
Drainage
outlet
One touch joint
Turn on
Secure strings and pull zips
up before putting laundry
into the washing machine.
(beneficial suggestion)
( )
• This is to prevent damage to
clothes and zips.
Clothes of easily-fadeaway
colors must be separated.
• The bluejeans that are inclined
to fade may decolor during
washing.
The jeans and alike
The vulnerable laundry shall
be put into the wash string
bag before washing.
• Prevent the laundry from dam-
aging by accident.
The laundry from which the
silk is inclined to run shall
be put into the string bag
before washing.
Please handle the dirt as
early as possible.
To be cautious, please put the laun-
dry with lace or the woman under-
wear with steel wire into the optional
wash string bag before washing.
The laundry made of corduroy or
other particular cloth, and the black
hose or other clothing sensitive to
silk-running shall be put into the
optional anti-silk-running string bag
before washing.
As it's hard to remove the dirt after
adhering to laundry for long, the
dirt shall be under cleanout and
handling with detergent before
washing, which brings better wash-
ing effect.
18
Put bulky or floating laundry in basket first.
The bluejeans and other thick cloth shall be evenly
distributed in the washing basket before washing.
(Prevent the laundry from overflowing during washing)
• Press the laundry with hand during water
supply, and make the water infiltrate the
cloth sufficiently.
• Splash of water must be prevented.
Put in the laundry as
evenly distributed as
possible.
How to put laundry in
Before Using Your Machine (continued)
( )
• It smoothes rotation of the laundry.
• Splash of water must be prevented.
Sheet
Checking Amount of Laundry and Detergent (Approximately Amount)
( )
Checking amount of laundry
Select the process required for washing after put in the laundry, and press the “
START/ PAUSE
” button. The sensors begin
to detect the weight of laundry, and the necessary detergent amount (approximate amount) and water level are displayed
correspondently. (The detection is not included in the processes of "SILK", "BLANKET", "BASKET CLEAN" .)
Amount of detergent (Approximately amount)
Display the necessary detergent amount and
water level.
2
The display of detergent amount (approximate amount) refers to the amount added with the
measuring spoon in the package of concentrated power detergent.
• The usage benchmark of detergent amount (approximate amount) is the capacity of one
measuring spoon (about 37g). (Other detergent 21)
37 21
• The capacity of measuring spoon depends on the brand of detergent, so please refer to the
description on the detergent package.
• The diagram example of detergent measuring spoon only stands for the approximate amount.
Please put in the detergent as
much as 80% of the capacity of
measuring spoon (about 30g).
80% 30
Put the laundry in, turn the power
ON, choice the appropriate
process, and press the
"
START
"
button.
1
• The pulsator rotates with absence of wa-
ter to check the washing load (cause no
damage to clothes)
Put the detergent in. 18~20
18~20
3
• Put detergent, fabric softener, bleach
and close the lid.
•
After the display of the detergent amount and
water level, please add in detergent in one
minute, and close the lid, otherwise it will
sound alarm. (at that time, if the "WATER
LEVEL" button is pressed, the washing ma-
chine will not wait any more and start rotating)
1
•
After the washing basket is filled with water
or begins operating, the replenishing deter-
gent shall be thrown into the basket directly.
Jean
19
How to install the detergent dispenser
Insert the pin into the pin hole at the injection opening.
3
2
How to uninstall the detergent dispenser
1 Bend the detergent dispenser.
2 Disassemble the pin off the pin hole.
Pin hole
Pin
3
2
Injection opening
Detergent dispenser
Pin
Pin hole
Start the washing machine with water in the washing basket, and the infiltration washing can't perform then. Please put the
detergent in the washing • spinning basket.
Put the detergent in the detergent dispenser
Powder synthetic detergent
• When water is adhering to the detergent dispenser, please wipe it first.
• When the detergent adheres to the dispenser, it remains even the dispenser is
closed. If the detergent still adheres to the dispenser after 2 or 3 times of repetitive
open and close, please clean up. ( 47)
2 3
( 47)
• Please pay attention to keep the detergent away from the injection opening of
fabric softener, so as to avoid malfunction.
• Some types of detergent may be hard to dissolve.
In this case, please inject the detergent into the washing basket directly after it
sufficiently dissolves.
• In the case of bulky laundry, sometimes it may be hard to open the detergent
dispenser.
In this case, please move the laundry to the opposite side of injection opening, then
open the dispenser.
• Only after closing the detergent dispenser can the operation begin. The laundry
may be damaged under the operation with the dispenser open.
• The detergent dispenser can be opened as much as about 90 degrees. Any action
to open it by force may cause damage.
90
Notes
2
Pour in the detergent
Detergent
dispenser
Lint filter
90
1
Open the detergent
dispenser
3
Close the deter-
gent dispenser
How to Use Liquid Detergent, Bleach and Fabric Softener
20
Liquid detergent/Bleach
/
Fabric softener
Open the cap of the fabric softener injection opening.
1
Pour the fabric softener into the injection opening in
accordance with the indication of water level before the
washing starts.
2
• Softener filling opening can only be opened by an angle of up to 120 .
Forced operation may damage the filling opening.
120
• When you find it difficult to pour the fabric softener into the injection
opening, push the basket to one side to pour the fabric softener in.
Close the cap of the fabric softener injection opening.
3
•
Please note that the cap of fabric softener injection opening should be closed.
Fabric softener will be dispensed into the basket during
the final rinse.
4
• Dispensation of the fabric softener is performed automatically by the
rotation of the spinning basket. The fabric softener moves in gradually
during the spinning and reaches the basket before the final spinning.
<Approximate amount of fabric softener>
< >
• Concentrated detergent: 6.6mL for 30L of water
30L 6.6mL
• Normal detergent: 20mL for 30L of water
30L 20mL
Fabric softener
• The concentrated type easily solidifies. Please use twice the amount of water to dilute such fabric softener.
2
• Once consumption of the softener shall be less than 45ml. Excessive consumption of the softener instead prevents it from being effective.
45mL
• Please do not leave the fabric softener in the basket for an extended period (12 hours) as the fabric softener may solidify and cause malfunction.
( 12 )
• When the washing machine or the basket is tilted, water may flow into fabric softener injection opening. (Thus fabric softener performance will be
reduced)
( )
• Please use an appropriate amount of detergent. Too much fabric softener may result in poor rinsing and fabric softener performance.
Notes
Water level 20L 30L 40L 50L
Concentrated type
Regular type
47911
mL mL mL mL
13 20 27 33
mL mL mL mL
120
Injection
opening
• Follow the instructions for the liquid detergent and bleach on the
labels for the usage amount and method to use.
• Please do not pour bleach directly onto the items being washed.
Otherwise, it may cause discoloring and damage the clothes.
Liquid detergent
Dilute the liquid detergent with water and gently pour it into
the injection opening.
• When using preset operation, dilute the detergent with twice the
amount of water.
Bleach
Dilute the bleach with water before the washing and gently
pour it into the injection opening.
Liquid detergent and bleach
injection opening
How to Use Liquid Detergent, Bleach and Fabric Softener (continued)
( )
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
