JY-SA10L

VEVOR JY-SA10L ユーザーマニュアル

  • VEVOR JY-SA10L 粉体塗装機のマニュアルの内容を理解しました。この装置の使用方法、メンテナンス、トラブルシューティングなど、ご質問にお答えできます。 安全上の注意事項、圧力調整、真空機能、エア漏れ対策など、マニュアルに記載されている情報に基づいてご説明しますので、お気軽にご質問ください。
  • 圧力調整はどうすれば良いですか?
    エア漏れが発生した場合、どうすれば良いですか?
    使用後の清掃方法は?
Technical Support and E-Warranty Certificate
www.vevor.com/support
POWDER COATING MACHINE
USER MANUAL
We continue to be committed to offering tools at competitive prices. "Save Half", "Half Price",
or any other similar expressions used by us only represent an estimate of savings you might
benefit from buying certain tools with us compared to the major top brands and do not
necessarily mean to cover all categories of tools offered by us. You are kindly reminded to
verify carefully when placing an order with us if you are saving half in comparison with the top
major brands.
1
JY-SA10L
Have product questions? Need technical support? Please feel free to
contact us:
CustomerService@vevor.com
NEED HELP? CONTACT US!
This is the original instruction, please read all manual instructions carefully
before operating. VEVOR reserves a clear interpretation of our user manual. The
appearance of the product shall be subject to the product you received. Please
forgive us that we won't inform you again if there are any technology or software
updates on our product.
POWDER COATING
MACHINE
2
SAFETY INSTRUCTION AND PRECAUTIONS
WARNING:
Read this material before using this product. Failure to do so can result in serious
injury. SAVE THIS MANUAL
Assembly precautions
1.Assemble only according to these instructions. Improper assembly can create
hazards.
2. Wear ANSI-approved safety goggles and heavy-duty work gloves during
assembly.
3.Keep assembly area clean and well lit.
4.Keep bystanders out of the area during assembly.
5.Do not assemble when tired or when under the influence of alcohol, drugs or
medication.
6.Product capabilities apply to properly and completely assembled product only.
7.Assemble on a flat, level, hard and smooth surface capable of safely supporting
a fully loaded Pressure Paint Pot.
WARNING:
1. This product is not a toy. Do not allow children to play with or near this item.
Children or persons with physical disabilities are prohibited from using this
product, and people who do not know how to use it safely are prohibited from
operating this product
2. This product 10L allows the paint to be pressurized to 70PSI, and the maximum
operating pressure must not exceed 75PSI, otherwise it will cause the risk of
injury to personal safety
3. The safety valve on the pressure barrel is used to protect the normal pressure
in the pressure barrel, avoid overpressure of a safety device, before the product
leaves the factory has been set within the allowable pressure range, in the normal
state of use, do not remove at will, do not adjust at will.
4. Do not do any form of modification of the product, do not do any dangerous
3
operations such as drilling, welding, etc., which may produce a tempering effect,
resulting in damage to the pressure barrel, affecting the service life of the
product
5. Use as intended only.
6. Inspect before every use; do not use if parts are loose or damaged.
7. Is strictly forbidden to pour strong acidic and alkaline liquid into this product to
avoid corrosive tank and cause personal injury
8. This bolt is positioned for the package to prevent collision and is removed
before use
4
1. Schematic diagram of the decomposition
5
serial number
DESCRIPTION
quantity
1
Pressure barrel body
1
2
Barrel lid
1
3
Sealing rings
1
4
M16 union bolts
4
5
M16 gasket
4
6
M16 butterfly nut
4
7
Barrel base
1
8
Movable wheel mount
4
9
Circlips
4
10
Fixed pins
4
11
Paint tips
1
12
Suction tube
1
13
handle
1
14
Discharge valve
1
15
Outlet valve
16
Tee connector
1
17
Flat base
1
18
Air intake fittings
1
19
Inlet valve
1
20
Intake regulator
1
21
2 points connector
1
22
relief valve
1
23
Vent valve plunger
1
24
Bleed valve
1
25
Pressure gauge
1
6
2. List of user thread specifications
SKU name
valve
Thread specifications
North
American
Standards
Air intakes
American style 1/4"
self-locking quick plug
tubing fitting
Air outlet (including
opening and closing
valve)
American 1/4", threaded
NPS, 18 teeth
Discharge port (with
opening and closing
valve)
American 3/8", threaded
NPS, 18 teeth
European
standards
Air intakes
European style 1/4"
self-locking quick plug
tubing fitting
Air outlet (including
opening and closing
valve)
European 1/4", thread G,
19 teeth
Discharge port (with
opening and closing
valve)
European 3/8", thread G,
19 teeth
Australian
standards
Air intakes
Japanese style 1/4"
self-locking quick plug
tubing fitting
Air outlet (including
opening and closing
valve)
European 1/4", thread G,
19 teeth
Discharge port (with
opening and closing
valve)
European 3/8", thread G,
19 teeth
7
3. preface
This paint barrel is composed of air pressure regulating valve, safety valve, vent
valve, discharge port and four movable wheels (optional). All parts are made of
the best materials, and have passed strict quality control, and the appearance is
treated with baking paint, so it can achieve the purpose of durability
4. Notes
After spraying with this product, it must be thoroughly cleaned to extend the
service life of the product
5. How to use
Before use, please confirm that there can be no residual pressure in the barrel, if
there is residual pressure, the operator can use the vent valve vent plunger pump
to completely drain it to ensure safety
1. Loosen the butterfly nut, and after the union bolt, open the bucket lid
2. Pour in the spray material
3. Close the bucket lid and tighten the butterfly nuts one by one in a diagonal
fashion
8
4. Close all valves, the sprayer inlet is connected to the barrel outlet (14), and the
sprayer inlet is connected to the barrel outlet valve (15)
5. Connect the air intake connection(18), open the intake valve(19)
9
6. Adjust the intake pressure regulator and rotate clockwise to adjust to the
required working pressure, or in a counterclockwise direction if you want to
reduce the pressure in the pressure barrel
7. Open the outlet valve(15)Open the discharge valve(14)
10
6. How to use vacuum
Before use, please confirm that there can be no residual pressure in the pressure
barrel, if there is residual pressure, the operator can use the vent valve vent
plunger pump to completely discharge it to ensure safety
1. Loosen the butterfly nut, and after the union bolt, open the bucket lid
2. Cover the bucket lid and tighten the butterfly nuts one by one in a diagonal
fashion
3. Close the discharge valve (14), tighten the vent valve plunger (23), connect the
vacuum machine to the intake joint (18), open the intake valve (19)
11
4. When the clockwise rotation air regulator (20) reaches -7.5 PSI, close the
intake valve at the same time(19)
7. Maintenance
1. After use, cut off the air source. Open the vent valve plunger on the lid to
completely release the air in the barrel, then loosen the butterfly nut, open the lid,
pour out the residual paint in the barrel, and clean all parts that have been
touched by the paint with an appropriate amount of solvent.
2. Pour the cleaning solvent into the bucket, close the lid to lock it, open the intake
valve, and operate the sprayer until the clean solvent appears
3. Safety valves must be kept clean at all times
8. Air leakage remedy
Note: If you find air leakage during use, please apply the glue evenly along here,
and then close the lid of the barrel; tighten the screws while the pressure reaches
15PSI; The time is about 10 seconds, so that the glue completely penetrates the
leakage, close the intake valve, open the pressure relief plunger, and stand still for
6-8 hours before continuing to use the glue after it is completely solidified.
12
9. Make sure to lock the bucket lid diagonally
Order of operations1-23-4
13
10. How to use epoxy resin bubble removal (this
method is a reference method, and users can adjust it
by themselves based on their own experience)
Before use, please confirm that there can be no residual pressure in the barrel, if
there is residual pressure, the operator can use the vent valve vent plunger pump
to completely drain it to ensure safety
1. Loosen the butterfly nut, and after the union bolt, open the bucket lid
2. After the epoxy resin is molded, it is placed in the tank
3. Barrel lid, tighten the butterfly nuts one by one in a diagonal fashion
4. Close the outlet connection(18), open the intake valve(19)
5. Adjust the intake pressure regulating valve, rotate clockwise to adjust to the
required working pressure of 0.35M, if you want to reduce the pressure in the
barrel, rotate in a counterclockwise direction, wait for the resin to solidify
completely, and take out after pressure relief.
14
11. Troubleshooting
fault
The cause of the failure
Exclusion method
The pointer of the
pressure gauge
connected to the air
supply does not move
1. The air source is not normal
2. The intake valve is not open
3. Other valves are not closed
1. Adjust the air source to
normal
2. Open the intake valve
3. Close other valves
Paint barrel lid leakage
1. When the barrel lid is
combined with the barrel body,
the butterfly nut is not tightened
diagonally
2. The parts on the barrel lid
are poorly sealed
1. Follow Article 3 of the
Terms of Use
2. Refer to the remedy for
air leakage
No paint
1. The discharge valve is not
open
1. Open the discharge valve
Poor paint effect
1. The pressure is too high or
too low
2. Spraying equipment
problems
1. Adjust to normal pressure
2. Repair of spraying
equipment
Items
Description
1
Name
Powder Coating Machine
2
Model
JY-SA10L
3
Parameter
Capacity:10LP(Max):70psi/0.482Mpa
VAC:-7.25psi/-0.05Mpa
4
Package
Size
450x310x310mm
5
G.W.
12.8KG
Technical Support and E-Warranty Certificate
www.vevor.com/support
/