Yamaha PSRE413 - KEYBOARD USB 100 PATTERNS ユーザーマニュアル

SERVICE MANUAL

HAMAMATSU, JAPAN

SERVICE MANUAL

PK

001801

20080601-

SPECIFICATIONS ................................3/4

PANEL LAYOUT ........................5

CIRCUIT BOARD LAYOUT & WIRING

..................................8

DISASSEMBLY PROCEDURE ..............10

LSI PIN DESCRIPTION ...............19

IC BLOCK DIAGRAM ....................22

CIRCUIT BOARDS .........................23

TEST PROGRAM ...............31/34

INITIALIZATION ........................................37

USER DATA BACKUP

........................38/39

MIDI IMPLEMENTATION CHART .............................40

MIDI DATA FORMAT .................................................41

PARTS LIST

BLOCK DIAGRAM

OVERALL CIRCUIT DIAGRAM

CONTENTS

Products names are as follows.

For Japanese market:

For overseas market:

DIGITAL KEYBOARD

PSR-E413

2

WARNING

WARNING: This product contains chemicals known to the State of California to cause cancer, or birth defects or other reproductive harm.

DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY REASON WHAT SO EVER!

Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or expose eyes to solder/

flux vapor!

If you come in contact with solder or components located inside the enclosure of this product, wash your hands before handling food.

IMPORTANT NOTICE

This manual has been provided for the use of authorized Yamaha Retailers and their service personnel. It has been assumed that basic

service procedures inherent to the industry, and more specifically Yamaha Products, are already known and understood by the users,

and have therefore not been restated.

WARNING : Failure to follow appropriate service and safety procedures when servicing this product may result in personal injury,

destruction of expensive components and failure of the product to perform as specified. For these reasons, we advise

all Yamaha product owners that all service required should be performed by an authorized Yamaha Retailer or the

appointed service representative.

IMPORTANT : This presentation or sale of this manual to any individual or firm does not constitute authorization certification,

recognition of any applicable technical capabilities, or establish a principal-agent relationship of any form.

The data provided is belived to be accurate and applicable to the unit(s) indicated on the cover. The research engineering, and service

departments of Yamaha are continually striving to improve Yamaha products. Modifications are, therefore, inevitable and changes in

specification are subject to change without notice or obligation to retrofit. Should any discrepancy appear to exist, please contact the

distributor’s Service Division.

WARNING : Static discharges can destroy expensive components. Discharge any static electricity your body may have accumulated

by grounding yourself to the ground bus in the unit (heavy gauge black wires connect to this bus.)

IMPORTANT : Turn the unit OFF during disassembly and parts replacement. Recheck all work before you apply power to the unit.

Components having special characteristics are marked and must be replaced with parts having speciﬁ cation equal to those

originally installed.

Saving and backing up your data

The panel settings and some other types of data

are not retained in memory when you turn off the

power to the instrument. Save data you want to

keep to the Registration Memory.

Saved data may be lost due to malfunction or

incorrect operation. Save important data to an

external device such as a computer.

SAVING DATA

Be sure to

perform it

3

PSR-E413

SPECIFICATIONS

Keyboards

• 61 standard-size keys (C1–C6), with Touch Response.

Display

• LCD display (backlit)

Setup

• STANDBY/ON

• MASTER VOLUME: MIN–MAX

Panel Controls

• VOICE CONTROL: [SPLIT], [DUAL], [HARMONY], [TOUCH]

• LIVE CONTROL: [ASSIGN]

• STYLE CONTROL: [ACMP ON/OFF], [INTRO/ENDING/rit.],

[MAIN/AUTO FILL], [SYNC STOP], [SYNC START], [START/

STOP]

• SONG CONTROL: [

] (REPEAT & LEARN), [A B] (A-B

REPEAT), [1] (REW), [¡] (FF), [8] (PAUSE), [3/7]

(START/STOP)

• REGIST MEMORY: [MEMORY/BANK], [1], [2]

• SONG MEMORY: [REC], [1]-[5], [A]

• LESSON: [START], [L], [R]

• ARPEGGIO: [ON/OFF], [TYPE]

• [DEMO/PC], [PERFORMANCE ASSISTANT], [FUNCTION],

[MUSIC DATABASE], [METRONOME], [PORTABLE

GRAND], [SONG], [EASY SONG ARRANGER], [STYLE],

[VOICE], Dial, CATEGORY[

¡

]/[

¡

], [0]-[9], [+]/[–], [TEMPO/

TAP]

Realtime Control

• Pitch Bend Wheel

• Knobs A, B

A: Cutoff, Reverb, Attack, Style Cutoff, Style Tempo

B: Resonance, Chorus, Release, Style Resonance

Voice

• 116 panel voices + 12 drum/SFX kits + 361 XGlite voices

+ 20 arpeggio voices

• Polyphony: 32

• DUAL

• SPLIT

Style

• 165 Preset Styles + External ﬁ les

• Style Control: ACMP ON/OFF, SYNC STOP,

SYNC START, START/STOP,

INTRO/ENDING/rit., MAIN/AUTO FILL

• Fingering: Multi Finger

• Style Volume

Music Database

• 300 + External ﬁ les

Education Feature

• Dictionary

• Lesson 1–3, Repeat & Learn

Registration Memory

• 8 banks x 2 types

Function

• VOLUME: Style Volume, Song Volume

• OVERALL: Tuning, Transpose, Split Point, Touch

Sensitivity, Pitch Bend Range

• MAIN VOICE: Volume, Octave, Pan, Reverb Level,

Chorus Level, Attack Time, Release Time,

Filter Cutoff, Filter Resonance

• DUAL VOICE: Voice, Volume, Octave, Pan, Reverb Level,

Chorus Level, Attack Time, Release Time,

Filter Cutoff, Filter Resonance

• SPLIT VOICE: Voice, Volume, Octave, Pan, Reverb Level,

Chorus Level, Attack Time, Release Time,

Filter Cutoff, Filter Resonance

• EFFECT: Reverb Type, Chorus Type, Master EQ Type

• HARMONY: Harmony Type, Harmony Volume

• ARPEGGIO: Arpeggio Type, Arpeggio Velocity

• SFF Load: Style File Load

• PC: PC Mode

• MIDI: Local On/Off, External Clock, Initial Send,

Keyboard Out, Style Out, Song Out

• METRONOME: Time Signature Numerator, Time Signature

Denominator, Metronome Volume

• LESSON: Lesson Track (R), Lesson Track (L)

• UTILITY: Grade, Demo Cancel, Sleep

Effects

• Reverb: 9 types

• Chorus: 4 types

• Harmony: 26 types

• Arpeggio: 100 types

Song

• 30 Preset Songs + 5 User Songs + Accessory CD-ROM

Songs (70)

• Song Clear, Track Clear

• Song Volume

• Song Control: REPEAT & LEARN, A-B REPEAT, PAUSE,

REW, FF, START/STOP

Performance assistant technology

Recording

• Song

User Song: 5 Songs

Recording Tracks: 1, 2, 3, 4, 5, STYLE

MIDI

• Local On/Off • Initial Send • External Clock

• Keyboard Out • Style Out • Song Out

Auxiliary jacks

• PHONES/OUTPUT, DC IN 12V, USB, SUSTAIN

Ampliﬁ er

• 2.5 W + 2.5 W

Speakers

• 12 cm x 2 + 3 cm x 2

Power Consumption

• 10 W

Power Supply

•

Adaptor: PA-130 or an equivalent recommended by Yamaha

• Batteries: Six “AA” size, LR6 or equivalent batteries

Dimensions (W x D x H)

• 946 x 402 x 136 mm (37-1/4" x 15-13/16" x 5-3/8")

Weight

• 7.0 kg (15 lbs. 7 oz.) (not including batteries)

Supplied Accessories

• Music Rest

• Accessory CD-ROM

• Owner’s Manual

Optional Accessories

• AC Power Adaptor: PA-130 or an equivalent

recommended by Yamaha

• Footswitch: FC4/FC5

• Keyboard Stand: L-2C/L-2L

• Headphones: HPE-150

PSR-E413

4

A B 8 1 ¡ 3/7

¡

5

PSR-E413

PANEL LAYOUT

q [STANDBY/ON] switch

w LIVE CONTROL

[ASSIGN] button

[A] and [B] knobs

e [MASTER VOLUME] control

r [DEMO/PC] button

t [PERFORMANCE ASSISTANT] button

y [EASY SONG ARRANGER] button

u [FUNCTION] button

i LESSON

[L], [R] buttons

[START] button

o [METRONOME] button

!0 [TEMPO/TAP] button

• Front Panel



'RAND0NO

/

-

)

0

1 6

2



A

A'

4

*













q

w

e

r

t

y

u

i

o

!0

PSR-E413

6

A

A'





















!1 SONG MEMORY

[REC], [1]–[5], [A] buttons

!2 ARPEGGIO

[ON/OFF] button

[TYPE] button

!3 SONG CONTROL

[

] (REPEAT & LEARN) button

[A B] (A-B REPEAT) button

[1] (REW) button

[¡] (FF) button

[8] (PAUSE) button

[3/7] (START/STOP) button

!1

!2

!3

AB

1

¡

8

3/7

7

PSR-E413

   

• Rear Panel

!4 STYLE CONTROL

[ACMP ON/OFF] button

[INTRO/ENDING/rit.] button

[MAIN/AUTO FILL] button

[SYNC STOP] button

[SYNC START] button

[START/STOP] button

!5 Dial

!6 CATEGORY [

1

] and [

1

] buttons

!7 [SONG] button

!8 [STYLE] button

!9 [MUSIC DATABASE] button

@0 [VOICE] button

@1 Number buttons [0]-[9],

[+] and [–] buttons

@2 [PORTABLE GRAND] button

@3 REGIST MEMORY

[MEMORY/BANK], [1], [2] buttons

@4 VOICE CONTROL

[SPLIT] button

[DUAL] button

[HARMONY] button

[TOUCH] button

@5 PITCH BEND wheel

@6 Drum Kit

@7 [USB] terminal

@8 [SUSTAIN] jack

@9 [PHONES/OUTPUT] jack

#0 [DC IN 12V] jack

!4

!5

!6

1

!7

!8

!9

@0

@1

@2

@3

@4

@5

@6

@7

@8

@9

#0

PSR-E413

8

CIRCUIT BOARD LAYOUT & WIRING

TW

8

Speaker L (WOOFER) Speaker R (WOOFER)

@

Speaker R (TWEETER)

TW

VRPB

MVR

JACK

PSW

PNL

PNR





2





ENC





;

.

=

B

>

:













@

2





(PB)

(VR)

DMLCD

TW

Speaker R (TWEETER)

TW

VRPB

MVR

JACK

PSW

PNL

PNR

ENC

(PB)

(VR)

DMLCD

Top view

Bottom view

UPPER CASE ASSEMBLY

9

PSR-E413

No. Unit Name Location Part No.

Connector

assembly

Destination Remarks

q

LCD Unit L70 (WC60260) BL Back light assembly *2 *5 PNL-CN206 *1 *4 2P L=70

w

Upper Case Assembly 500 (WM45500) USB JACK-CN104 *1 *4 DMLCD-CN802 *1 *4 5P

e

Lower Case Keyboard

Assembly

30 WM232300 MK1 61H-MK-CN1 *1 *4 DMLCD-CN401 *1 *4 12P

r

40 WM232500 MK2 61H-MK-CN2 *1 *4 DMLCD-CN403 *1 *4 5P

t

50 WM232600 MK3 61L-MK-CN5 *1 *4 DMLCD-CN402 *1 *4 7P

y

120 (WM23410) BATT Contact Spring (+/–) *2 *6 JACK-CN101 *1 *9 3P

u

Lower Case Assembly 30 (WM23400) SP

Speaker L (WOOFER) *2 *7

JACK-CN105 *1 *10 4P L=450

Speaker R (WOOFER) *2 *8

i

JACK Circuit Board

WH103 (WM23220) PEDAL JACK-CN103 *3 *4 DMLCD-CN803 *1 *4 4P

o

WH106 (WM23160) TW JACK-CN106 *3 *4 TW (+/–) *2 *5 2P Rch

!0

WH107 (WM23160) TW JACK-CN107 *3 *4 TW (+/–) *2 *5 2P Lch

!1

PSW Circuit Board WH108 (WM23150) PSW PSW-CN108 *3 *4 PNL-CN202 *1 *4 4P

!2

PNL Circuit Board

WH201 (WM22940) AMJK PNL-CN201 *3 *4 JACK-CN102 *1 *4 8P

!3

WH204 (WM23110) PNL PNL-CN204 *3 *4 DMLCD-CN702 *1 *4 12P

!4

WH205 (WM23080) AMDM PNL-CN205 *3 *4 DMLCD-CN101 *1 *4 13P

!5

VRPB (VR) Circuit Board WH301 (WM23200) VR VRPB (VR)-CN301 *3 *4 DMLCD-CN801 *1 *4 10P

!6

VRPB (PB) Circuit Board WH401 (WM23210) PB VRPB (PB)-CN401 *3 *4 VRPB (VR)-CN302 *3 *4 3P

!7

ENC Circuit Board WH501 (WM23170) ENC ENC-CN501 *3 *4 PNR-CN802 *1 *4 3P

!8

MVR Circuit Board WH601 (WM23180) MVR MVR-CN601 *3 *4 PNL-CN203 *1 *4 5P

!9

PNR Circuit Board WH801 (WM23140) PNR PNR-CN801 *3 *4 DMLCD-CN701 *1 *4 16P

* The parts with “( )” in “Part No.” are not available as spare parts.

*1: Installation

*2: Manual soldering

*3: Dip soldering

*4: Edge mark is adjusted to Pin 1 mark (

mark).

*5: Edge mark is adjusted to + mark.

*6: Red wire is connected to (+) terminal. Black wire is connected to (–) terminal.

*7: White wire is connected to (+) terminal. Black wire is connected to (–) terminal.

*8: Red wire is connected to (+) terminal. Black wire is connected to (–) terminal.

*9: Red wire is adjusted to Pin 1 mark (

mark).

*10: White wire is adjusted to Pin 1 mark ( mark).

Caution: Be sure to attach the removed ﬁ lament tape just as it

was before removal.

Keyboard assembly

61L-MK

61H-MK

;

.

=

B

Top view

LOWER CASE KEYBOARD ASSEMBLY

PSR-E413

10

DISASSEMBLY PROCEDURE

Caution:

Be sure to attach the removed ﬁ lament tape just as it was before removal.

1. Lower Case Assembly

(Time required: About 2 minutes)

1-1 Remove the six (6) screws marked [80A], two (2)

screws marked [90] and two (2) screws marked

[100A]. The lower case assembly can then be

removed. (Fig.1)

Fig.1

[80A]: BIND HEAD TAPPING SCREW-B 3.0X12 MFZN2W3 (WE98740R)

[90]: BIND HEAD TAPPING SCREW-B 3.0X20 MFZN2W3 (WF48930R)

[100A]: BIND HEAD TAPPING SCREW-B 3.0X30 MFZN2W3 (WF49100R)

[100A] [80A]

[100A]

[80A]

[90][90]

BATTERY COVER ASSEMBLY

Top view

Bottom view

VOLUME KNOB

ROTARY KNOB

ENCODER KNOB

SPEAKER GRILLE L

SPEAKER GRILLE R

LOWER CASE KEYBOARD ASSEMBLY

LOWER CASE ASSEMBLY

11

PSR-E413

2. JACK Circuit Board

(Time required: About 3 minutes)

2-1

Remove the lower case assembly. (See procedure 1.)

2-2 Remove the connector assemblies TW soldered to

the right and left TW circuit boards. (Fig. 2)

2-3 Remove the seven (7) screws marked [380A]. The

JACK circuit board can then be removed. (Fig.2)

3. LCD Unit

(Time required: About 4 minutes)

3-1

Remove the lower case assembly. (See procedure 1.)

3-2

Remove the JACK circuit board. (See procedure 2.)

3-3 Remove the six (6) screws marked [380B]. The

LCD unit can then be removed. (Fig.2)

[100B]

[80B]

Bottom view

LOWER CASE KEYBOARD ASSEMBLY

SPEAKER R (TWEETER)

[380G]

R

TW

CONNECTOR

ASSEMBLY TW

SPEAKER L (TWEETER)

CONNECTOR

ASSEMBLY TW

[380F]

UPPER CASE ASSEMBLY

L

TW

[380D] x 4

ENC

[380A]

[380B]

LCD UNIT

[380B]

JACK

[380C]

MVR

[380E]

PSW

HOOK (A)

Fig.2

[80B]: BIND

HEAD TAPPING SCREW-B 3.0X12 MFZN2W3 (WE98740R)

[100B]: BIND HEAD TAPPING SCREW-B 3.0X30 MFZN2W3 (WF49100R)

[380]: BIND HEAD TAPPING SCREW-B 3.0X8 MFZN2W3 (WE774300)

4.

DMLCD Circuit Board, Back Light Assembly

and LCD

(Time required: About 5 minutes)

4-1

Remove the lower case assembly. (See procedure 1.)

4-2 Remove the JACK circuit board.(See procedure 2.)

4-3 Remove the LCD unit. (See procedure 3.)

4-4 Remove the eight (8) screws marked [L50]. The

DMLCD circuit board can then be removed from

the LCD unit. (Fig.3)

PSR-E413

12

4-5 Remove the LCD, back light assembly and rubber

connectors from the LCD frame. (Fig.3)

* When attaching the rubber connector to the

LCD frame, set the conductor side to face

inward. (Fig.4)

* When installing the DMLCD circuit board,

tighten the screws 1 through 8 in numerical

order as shown in Fig.5. If the DMLCD circuit

board is replaced, execute the "Factory Set" in

the test program.

[L50]: BIND HEAD TAPPING SCREW-B

3.0X12 MFZN2W3 (WE98740R)

5. MVR Circuit Board

(Time required: About 3 minutes)

5-1 Remove the “MASTER VOLUME” volume knob

from the control panel as shown in Fig.6. (Fig.1,

Fig.6)

5-2

Remove the lower case assembly. (See procedure 1.)

5-3 Remove the three (3) screws marked [380C]. The

MVR circuit board can then be removed. (Fig.2)

6. ENC Circuit Board

(Time required: About 3 minutes)

6-1 Pull out the "CATEGORY" encoder knob from the

control panel as shown in Fig.7. (Fig.1, Fig.7)

6-2

Remove the lower case assembly. (See procedure 1.)

6-3

Remove the four (4) screws marked [380D]. The

ENC circuit board can then be removed. (Fig.2)

[L50]

LCD FRAME

LCD

BACK LIGHT ASSEMBLY

RUBBER CONNECTOR

LCD HOLDER

DMLCD

CONDUCTOR SIDE

RUBBER CONNECTOR

1

2

3

4

5

6

7

8

DMLCD

Fig.3

Fig.4

Fig.5

13

PSR-E413

7.

PSW Circuit Board

(Time required: About 3 minutes)

7-1

Remove the lower case assembly. (See procedure 1.)

7-2 Remove the two (2) screws marked [380E]. The

PSW circuit board can then be removed. (Fig.2)

7-3 Pull out the push knob from the PSW circuit board.

(Fig.8)

VOLUME KNOB

PUSH KNOB

PSW

Fig.6

Fig.8

ENCODER KNOB

Fig.7

8.

TW Circuit Boards and Speakers (Tweeters)

(Time required: About 3 minutes each)

8-1

Remove the lower case assembly. (See procedure 1.)

8-2 TW Circuit Board (L) and Speaker L (Tweeter)

Remove the connector assembly TW and speaker

cable soldered to the TW circuit board (L) and

remove the two (2) screws marked [380F]. The

TW circuit board (L) and speaker L (tweeter) can

then be removed. (Fig. 2)

8-3 TW Circuit Board (R) and Speaker R (Tweeter)

Remove the connector assembly TW and speaker

cable soldered to the TW circuit board (R) and

remove the two (2) screws marked [380G]. The

TW circuit board (R) and speaker R (tweeter) can

then be removed. (Fig. 2)

9. Speaker Grilles L and R

(Time required: About 3 minutes each)

9-1

Remove the lower case assembly. (See procedure 1.)

9-2 Set the eight (8) hooks [A] parallel to the groove in

the upper case assembly and remove the speaker

grille L. (Fig.1, Fig.2)

* The speaker grille R can be removed in the

same manner.

PSR-E413

14

[380H] x 13

[380I]

[380J]

(VR)

(PB)

[380K]

WHEEL ASSEMBLY

PNR

PNL

VRPB

Bottom view

10. Lower Case Keyboard Assembly

(Time required: About 3 minutes)

10-1

Remove the lower case assembly. (See procedure 1.)

10-2 Remove the two (2) screws marked [80B] and the

screw marked [100B]. The lower case keyboard

assembly can then be removed. (Fig.2)

11.

PNL Circuit Board

(Time required: About 5 minutes)

11-1

Remove the lower case assembly. (See procedure 1.)

11-2 Remove the lower case keyboard assembly.

(See procedure 10.)

11-3 Remove the thirteen (13) screws marked [380H].

The PNL circuit board can then be removed. (Fig.9)

12.

PNR Circuit Board

(Time required: About 5 minutes)

12-1

Remove the lower case assembly. (See procedure 1.)

12-2 Remove the lower case keyboard assembly.

(See procedure 10.)

12-3

Remove the eleven (11) screws marked [380I]. The

PNR circuit board can then be removed. (Fig.9)

Fig.9

[380]: BIND HEAD TAPPING SCREW-B 3.0X8 MFZN2W3 (WE774300)

UPPER CASE ASSEMBLY

15

PSR-E413

13.

VRPB (VR+PB) Circuit Board and Wheel

Assembly

(Time required: About 4 minutes)

13-1 Pull out the two (2) rotary knobs for "A" and "B"

from the control panel. (Fig.1)

13-2

Remove the lower case assembly. (See procedure 1.)

13-3 Remove the lower case keyboard assembly.

(See procedure 10.)

13-4 Remove the five (5) screws marked [380J] and

two (2) screws marked [380K]. The VRPB (VR+PB)

circuit board can then be removed with the wheel

assembly attached. (Fig. 9)

13-5 Pull out the wheel assembly from the VRPB (PB)

circuit board. (Fig.10)

SPEAKER L (WOOFER)

SPEAKER R (WOOFER)

[40]

Top view

Fig.11

LOWER CASE ASSEMBLY

[40]: BIND HEAD TAPPING SCREW-B 4.0X12 MFZN2W3 (WE98120R)

WHEEL ASSEMBLY

(PB)

VRPB

Fig.10

14. Speakers (Woofers)

(Time required: About 3 minutes)

14-1

Remove the lower case assembly. (See procedure 1.)

14-2 Remove the four (4) each screws marked [40] to

the right and left. The speakers (woofers) to the

right and left can then be removed. (Fig.11)

PSR-E413

16

15. Disassembling Keyboard Assembly

(Time required: About 13 minutes)

15-1

Remove the lower case assembly. (See procedure 1.)

15-2 Remove the lower case keyboard assembly.

(See procedure 10.)

15-3 White Keys and Black Keys

15-3-1 White and black keys for one octave unit are

integrated as a set. There are five sets in total.

Only the C6 white key, unlike the other keys, is not

integrated in a set. (Fig.12)

15-3-2 To remove a set, remove the four (4) each screws

marked [120A]. The white and black keys in the

set can then be removed. (Fig.12)

When removing, unfasten the two (2) hooks at the

back of the black keys upward, and lift the white

and black keys while pulling them toward you a

little. (Photo 1)

15-3-3 To remove the white key C6, remove the screw

marked [120B], unhook as described in Procedure

15-3-2, and pull out toward you. (Fig.12)

15-4 Rubber Contact

15-4-1 Remove the white and black keys corresponding

to the rubber contacts to be removed. (See Fig.12

and Procedure 15-3.)

15-4-2 Remove the rubber contacts. (Photo 2, Fig.13)

[120A]

C1

B2 B3 C4 C6

[120A]

[120A] [120B][120A]

[120A]

Top view

KEYBOARD ASSEMBLY

HOOK

Fig.12

[120]: BIND HEAD TAPPING SCREW-P 3.0X20 MFZN2W3 (WE49200R)

Photo 1

RUBBER CONTACT

Photo 2

LOWER CASE KEYBOARD ASSEMBLY

17

PSR-E413

15-5 Circuit Board 61L-MK

15-5-1 Remove the white and black keys from C1 to B3.

(See Fig.12 and Procedure 15-3.)

15-5-2 Remove the four (4) screws marked [100C] and

eight (8) screws marked [110A]. The circuit board

61L-MK can then be removed. (Fig.13)

*

When installing the circuit board 61L-MK, tighten

the screws 1 through 12 in numerical order as

shown in the ﬁ gure "61L-MK" in Fig.14. (Fig.14)

15-6 Circuit Board 61H-MK

15-6-1 Remove the white and black keys from C4 to C6.

(See Fig.12 and Procedure 15-3.)

15-6-2 Remove the three (3) screws marked [100D] and

five (5) screws marked [110B]. The circuit board

61H-MK can then be removed. (Fig.13)

*

When installing the circuit board 61H-MK, tighten

the screws 1 through 8 in numerical order as

shown in the ﬁ gure "61H-MK" in Fig.14. (Fig.14)

[100C]

[110A]

[100C] [100C]

[100C]

[100D]

[100D] [100D]

[110A] [110B]

61H

RUBBER CONTACT

61L-MK

61H-MK

Top view

[100]: BIND HEAD TAPPING SCREW-B 3.0X8 MFZN2W3 (WE774300)

[110]: BIND HEAD TAPPING SCREW-P 3.0X12 MFZN2W3 SP (WH899400)

LOWER CASE KEYBOARD ASSEMBLY

Fig.13

23 4 5 6 7 8 1 1 2345

910 11 126 7 8

61L-MK

61H-MK

Fig.14

PSR-E413

18

HOOK

SPRING TERMINAL B

SPRING TERMINAL D

SPRING TERMINAL A

HOOK

SPRING TERMINAL C

SPRING TERMINAL

C

Fig.15

Fig.16

16. How to Remove Spring Terminals

16-1 Spring Terminal A and Spring Terminal B

(Time required: About 4 minutes each)

16-1-1

Remove the lower case assembly. (See procedure 1.)

16-1-2 Remove the lower case keyboard assembly.

(See procedure 10.)

16-1-3 Remove the white and black keys from C1 to B2

(See Fig. 12 and Procedure 15-3.)

16-1-4 Remove the connector assembly BATT soldered

to the spring terminal A and spring terminal B.

(Photo 3)

16-1-5 Reverse the lower case keyboard assembly and

remove the battery cover assembly. (Fig.1)

16-1-6 Lift the spring terminal A a little and slide it in the

upper right direction to remove it. (Fig.15)

16-1-7 Remove the hook for the spring terminal B to pull

it out from inside. (Fig.15)

16-2 Spring Terminal C and Spring Terminal D

(Time required: About 1 minute each)

16-2-1 Remove the battery cover assembly.

(See procedure 16-1-5)

16-2-2 Remove the hooks to pull out the spring terminal

C and spring terminal D. (Fig.15, Fig.16)

SPRING TERMINAL A

SOLDERING

CONNECTOR ASSEMBLY BATT

SPRING TERMINAL B

Photo 3

19

PSR-E413

LSI PIN DESCRIPTION

ADC084S021CIMM

(X6905A00)

ADC

(Analog to Digital Converter) .................................................

20

AK4385ET

(X6040A01)

DAC

(Digital to Analog Converter) ................................................................

20

M38K07M4L-315HP

(X7797A00)

CPU

(USB) ....................................................................................

20

ML9040A-B01GAZ03A

(XZ987A0R)

LCD DRIVER

...........................................................................

21

NT3881DFG-01

(X3148A0R)

LCD DRIVER

.......................................................................................

21

YMW767-VTZ

(X6055A0R)

CPU

(SWL01T) .......................................................................................

19

NO.

I/O FUNCTIONNAME

NO.

I/O FUNCTIONNAME

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

33

34

35

36

37

38

39

40

41

42

43

44

45

46

47

48

49

50

51

52

53

54

55

56

57

58

59

60

61

62

63

64

Vss

TESTN

PLLBPN

PLLV

DD

CIN

PLLVss

TRSTN

TMS

TCK

TDI

TDO

XI

XO

Vss

V

DD

ICN

ECSN

EWRN/PD5

ERDN/PD4

EA3/PD3

EA2/PD2

EA1/PD1

EA0/PD0

IOV

DD

ED0/PC0

ED1/PC1

ED2/PC2

ED3/PC3

ED4/PC4

ED5/PC5

ED6/PC6

ED7/PC7

Vss

IRQ0N/PH0

TxD0

RxD0

TxD1/PG2

RxD1/PH1

SCLK1/PH2

SDO

SDI/PH3

BCLK

WCLK/SYO

SYSCLK/PG3

Vss

V

DD

IOVDD

PA0

PA1

PA2

PA3

PA4

PA5

PA6

PA7

Vss

PB0

PB1

PB2

PB3

PB4

PB5

PB6

PB7/SYI

-

I

-

I

O

I

O

-

I

-

I/O

-

I

O

I

O

I

O

I

O

-

I/O

-

I/O

Ground

Input for TEST

PLL bypass select

PLL Power supply +2.5 V

Capacitor terminal for PLL

PLL Ground

JTAG input

JTAG output

Crystal oscillator

Ground

Power supply +2.5 V

Hardware reset

CPU I/F chip select

CPU I/F write enable / Port D

CPU I/F read enable / Port D

CPU I/F address bus / Port D

Power supply +3.3 V

CPU I/F data bus / Port C

Ground

Interrupt input / Port H

Serial output

Serial input

Serial output / Port G

Serial input / Port H

External synchronization clock / Port H

Serial output

Serial input / Port H

Bit clock output

Word clock output

Clock output / Port G

Ground

Power supply +2.5 V

Power supply +3.3 V

I/O port A

Ground

I/O port B

65

66

67

68

69

70

71

72

73

74

75

76

77

78

79

80

81

82

83

84

85

86

87

88

89

90

91

92

93

94

95

96

97

98

99

100

101

102

103

104

105

106

107

108

109

110

111

112

113

114

115

116

117

118

119

120

121

122

123

124

125

126

127

128

Vss

IOV

DD

LBN/LWRN/PF6

UBN/UWRN/PF7

RDN/PF4

MD00

MD08

MD01

MD09

MD02

MD10

MD03

Vss

MD11

MD04

MD12

MD05

MD13

MD06

MD14

MD07

MD15

WRN/PF5

Vss

V

DD

IOVDD

MA17

MA16

MA15

MA14

MA13

MA12

MA11

MA10

MA09

MA08

MA07

MA06

MA05

Vss

MA04

MA03

MA02

MA01

CS0N/PG0

MA18

MA19

MA21/PF1

MA22/PF2

MA20

MA23/PF3

CSIN/PG1

MA00/PF0

Vss

VDD

IOVDD

CS2N/PE0

CS3N/PE1

CS4N/CASN/PE2

CS5N/PE3

CS50RDN/PE4

CS51WRN/PE5

CS52WRN/PE6

CS53WRN/RASN/PE7

-

O

I/O

-

I/O

O

-

O

-

O

-

O

Ground

Power supply +3.3 V

External memory lower-byte enable / Port F

External memory upper-byte enable / Port F

External memory read enable / Port F

External memory data bus

Ground

External memory data bus

Ground

Power supply +2.5 V

Power supply +3.3 V

External memory address bus

Ground

External memory address bus

External memory chip select / Port G

External memory address bus

External memory address bus / Port F

External memory address bus

External memory address bus / Port F

External memory chip select / Port G

External memory address bus / Port F

Ground

Power supply +2.5 V

Power supply +3.3 V

External memory chip select / Port E

YMW767-VTZ (X6055A0R) CPU (SWL01T)

DMLCD: IC301

PSR-E413

20

NO.

NAME

I/O

FUNCTION

NO.

NAME

I/O

FUNCTION

I Master Clock

Rch Analog out(-)

I Audio Serial Data Clock

Rch Analog out(+)

I Audio Serial Date Input

Lch Analog out(-)

I L/R Clock

Lch Analog out(+)

I Power Down mode

Ground

I Chip Select

Power Supply

I Control Data Input

Rch Data Zero Input Detect

I Control Data Input

Lch Data Zero Input Detect

1

2

3

4

5

6

7

8

MCLK

BICK

SDTI

LRCK

PDN

CSN

CCLK

CDTI

9

10

11

12

13

14

15

16

AOUTR-

AOUTR+

AOUTL-

AOUTL+

Vss

VDD

DZFR

DZFL

O

-

O

DMLCD: IC501

AK4385ET (X6040A01) DAC (Digital to Analog Converter)

NO.

I/O FUNCTIONNAME

NO.

I/O FUNCTIONNAME

1

2

3

4

5

CS

VA

GND

AIN4

AIN3

I

-

I/O

Chip select

Power supply +3.3 V

Ground

Analog input

6

7

8

9

10

AIN2

AIN1

DIN

DOUT

SCLK

I/O

I

O

I

Analog input

Digital data input

Digital data output

Digital clock input

ADC084S021CIMM

(X6905A00) ADC (Analog Digital Converter)

DMLCD: IC801

NO.

I/O FUNCTIONNAME

NO.

I/O FUNCTIONNAME

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

P12/DQ2/AN2

P13/DQ3/AN3

P14/DQ4/AN4

P15/DQ5/AN5

P16/DQ6/AN6

P17/DQ7/AN7

CNVss

RESET

VccE

VREF

Vss

XIN

XOUT

Vcc

CNVss2

P60(LED0)

P6

1(LED1)

P6

2(LED2)

P6

3(LED3)

PVss

PVcc

DVcc

USBVREF

TrON

D0+

D0-

P20

P21

P22

P23

P24

P25

I/O

I

-

I

-

I

O

-

I

I/O

-

O

I/O

Port P1 (In/output)/External bus interface/

A-D converter input

Chip active

System reset input

Analog power supply +3.3 V

Reference voltage input

Ground

Clock input

Clock output

Power supply +3.3 V

Chip active

Port P6 (In/output)

Analog ground

Analog power supply +3.3 V

USB reference power supply +3.3 V

USB reference voltage output

USB upstream in/output

Port P2 (In/output)

33

34

35

36

37

38

39

40

41

42

43

44

45

46

47

48

49

50

51

52

53

54

55

56

57

58

59

60

61

62

63

64

P26

P27

P50/INT0

P51/CNTR0

P52/INT1

P53

P54

P55

P56

P57

P00

P01

P02

P03

P04

P05

P06

P07

P40/ExDREQ/RxD

P41/ExDACK/TxD

P42/ExTC/SCLK

P43/ExA1/SRDY

P30

P31

P32

P33/ExINT

P34/ExCS

P35/ExWR

P36/ExRD

P37/ExA0

P10/DQ0/AN0

P11/DQ1/AN1

I/O

Port P2 (In/output)

Port P5 (In/output)/Interrupt input

Port P5 (In/output)/Timer X

Port P5 (In/output)/Interrupt input

Port P5 (In/output)

Port P0 (In/output)

Port P4 (In/output)/Serial I/O/External bus interface

Port P3 (In/output)

Port P3 (In/output)/External bus interface

Port P1 (In/output)/External bus interface/

A-D converter input

M38K07M4L-315HP (X7797A00) CPU (USB)

DMLCD: IC802

ページを読み込んでいます...

Yamaha PSRE413 - KEYBOARD USB 100 PATTERNS ユーザーマニュアル

Yamaha PSRE413 - KEYBOARD USB 100 PATTERNS ユーザーマニュアル

関連論文

その他の書類