STCT1830
English 3
繁體中文 11
18
2
A
B
C
D E
3
F G
H I
4
ENGLISH
CORDLESS OSCILLATING
STCT1830
Technical Data
STCT1830
Input power V 18
No-load speed/rated
speed min
-1
8000-18000
Oacillating angle Degrees 1.4 or 2.8
Weight kg 1.4
charger 90588647(KR) 90600163(TW)
Input power V AC 220 110
Output Voltage VDC 18 18
Current A 2 2
Approx. charge time min 60-120 60-120
Battery STBL182L STBL184L
Voltage VDC 18 18
Capacity Ah 2.0 4.0
Type Li-Ion Li-Ion
Your Stanley oscillating tool has been designed
for DIY applications such as sanding operations.
It is also suitable for cutting wooden materials,
plastic, gypsum, non-ferrous metals and fastening
elements (e.g., unhardened nails, staples), work-
ing soft wall tiles and scraping of small surfaces.
This tool is intended for professional and private,
non professional users.
Safety instructions
General power tool safety warnings
WARNING! Read all safety warnings
and all instructions. Failure to follow the
warnings and instructions listed below
may result in electric shock, re and/or
serious injury.
Save all warnings and instructions for future
reference. The term “power tool” in all of the
warnings listed below refers to your mains
operated (corded) power tool or battery operated
(cordless) power tool.
1. Work area safety
a. Keep work area clean and well lit. Cluttered
or dark areas invite accidents.
b. Do not operate power tools in explosive
atmospheres, such as in the presence of
ammable liquids, gases or dust. Power
tools create sparks which may ignite the dust or
fumes.
c. Keep children and bystanders away while
operating a power tool. Distractions can
cause you to lose control.
2. Electrical safety
a. Power tool plugs must match the outlet.
Never modify the plug in any way. Do not
use any adapter plugs with earthed
(grounded) power tools. Unmodied plugs
and matching outlets will reduce risk of electric
shock.
b. Avoid body contact with earthed or
grounded surfaces such as pipes, radiators,
ranges and refrigerators. There is an
increased risk of electric shock if your body is
earthed or grounded.
c. Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
d. Do not abuse the cord. Never use the cord
for carrying, pulling or unplugging the
power tool. Keep cord away from heat, oil,
sharp edges or moving parts. Damaged or
entangled cords increase the risk of electric
shock.
e. When operating a power tool outdoors, use
an extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces
the risk of electric shock.
f. If operating a power tool in a damp location
is unavoidable, use a residual current
device (RCD) protected supply. Use of an
RCD reduces the risk of electric shock.
3. Personal safety
a. Stay alert, watch what you are doing and
use common sense when operating a power
tool. Do not use a power tool while you are
tired or under the inuence of drugs,
alcohol or medication. A moment of
inattention while operating power tools may
result in serious personal injury.
b. Use personal protective equipment. Always
wear eye protection. Protective equipment
such as dust mask, non-skid safety shoes, hard
hat, or hearing protection used for appropriate
5
ENGLISH
conditions will reduce personal injuries.
c. Prevent unintentional starting. Ensure the
switch is in the off-position before
connecting to power source and/or battery
pack, picking up or carrying the tool.
Carrying power tools with your nger on the
switch or energising power tools that have the
switch on invites accidents.
d. Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key
left attached to a rotating part of the power tool
may result in personal injury.
e. Do not overreach. Keep proper footing and
balance at all times. This enables better
control of the power tool in unexpected
situations.
f. Dress properly. Do not wear loose clothing
or jewellery. Keep your hair, clothing and
gloves away from moving parts. Loose
clothes, jewellery or long hair can be caught in
moving parts.
g. If devices are provided for the connection of
dust extraction and collection facilities,
ensure these are connected and properly
used. Use of dust collection can reduce
dust-related hazards.
4. Power tool use and care
a. Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the
rate for which it was designed.
b. Do not use the power tool if the switch does
not turn it on and off. Any power tool that
cannot be controlled with the switch is
dangerous and must be repaired.
c. Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such
preventive safety measures reduce the risk of
starting the power tool accidentally.
d. Store idle power tools out of the reach of
children and do not allow persons
unfamiliar with the power tool or these
instructions to operate the power tool.
Power tools are dangerous in the hands of
untrained users.
e. Maintain power tools. Check for
misalignment or binding of moving parts,
breakage of parts and any other condition
that may affect the power tools operation. If
damaged, have the power tool repaired
before use. Many accidents are caused by
poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to
control.
g. Use the power tool, accessories and tool
bits etc. in accordance with these
instructions, taking into account the
working conditions and the work to be
performed. Use of the power tool for
operations different from those intended could
result in a hazardous situation.
5. Battery tool use and care
a) Recharge only with the charger specied by
the manufacturer. A charger that is suitable for
one type of battery pack may create a risk of
re when used with another battery pack.
b) Use power tools only with specically
designated battery packs. Use of any other
battery packs may create a risk of injury and
re.
c) When battery pack is not in use, keep it away
from other metal objects, like paper clips,
coins, keys, nails, screws or other small
metal objects, that can make a connection
from one terminal to another. Shorting the
battery terminals together may cause burns or
a re.
d) Under abusive conditions, liquid may be
ejected from the battery; avoid contact. If
contact accidentally occurs, ush with water. If
liquid contacts eyes, additionally seek medical
help. Liquid ejected from the battery may cause
irritation or burns.
6. Service
a) Have your power tool serviced by a qualied
repair person using only identical
replacement parts. This will ensure that the
safety of the power tool is maintained.
Additional power tool safety warnings
Warning! Additional safety warnings for oscillat-
ing tools
u Hold power tool by insulated gripping
surfaces when performing an operation
where the cutting accessory may contact
6
ENGLISH
hidden wiring.Cutting accessory contacting a
“live” wire may make exposed metal parts of the
power tool “live” and could give the operator an
electric shock.
u Use clamps or another practical way to
secure and support the workpiece to a
stable platform. Holding the work by hand or
against your body leaves it unstable and may
lead to loss of control.
Warning! Contact with or inhalation of
dusts arising from sanding applications
may endanger the health of the operator
and possible bystanders. Wear a dust
mask specically designed for protection
against dust and fumes and ensure that
persons within or entering the work area
are also protected.
u Thoroughly remove all dust after sanding.
u Take special care when sanding paint which is
possibly lead based or when sanding some
woods and metal which may produce toxic dust:
u Do not let children or pregnant women enter
the work area.
u Do not eat, drink or smoke in the work area.
u Dispose of dust particles and any other debris
safely.
u The intended use is described in this instruction
manual. The use of any accessory or
attachment or performance of any operation
with this tool other than those recommended in
this instruction manual may present a risk of
personal injury and/or damage to property.
u The accessory will continue to move after
releasing the switch. Always switch the tool off
and wait for the accessory to come to a
complete standstill before putting the tool down.
u Keep hands away from cutting area. Never
reach underneath the work piece for any
reason. Do not insert ngers or thumb into the
vicinity of the reciprocating blade and blade
clamp. Do not stabilize the saw by gripping the
shoe.
u Keep blades sharp. Dull or damaged blades
may cause the saw to swerve or stall under
pressure. Always use the appropriate type of
saw blade for the workpiece material and type
of cut.
u When cutting pipe or conduit, make sure that
they are free from water, electrical wiring, etc.
u Do not touch the workpiece or the blade
immediately after operating the tool. They can
become very hot.
u Be aware of hidden hazards, before cutting into
walls, oors or ceilings, check for the location of
wiring and pipes.
Safety of others
u This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or lack
of experience and knowledge, unless they have
been given supervision or instruction
concerning use of the appliance by a person
responsible for their safety.
u Children should be supervised to ensure that
they do not play with the appliance.
Residual risks
Additional residual risks may arise when using the
tool which may not be included in the enclosed
safety warnings. These risks can arise from mis-
use, prolonged use etc.Even with the application of
the relevant safety regulations and the implemen-
tation of safety devices, certain residual risks can
not be avoided. These include:
u Injuries caused by touching any rotating/moving
parts.
u Injuries caused when changing any parts,
blades or accessories.
u Injuries caused by prolonged use of a tool.
When using any tool for prolonged periods
ensure you take regular breaks.
u Impairment of hearing.
u Health hazards caused by breathing dust
developed when using your tool (example:-
working with wood, especially oak, beech and
MDF.)
Labels on tool
The following pictograms are shown on the tool:
:
Warning! To reduce the risk of injury, the
user must read the instruction manual.
Additional safety instructions for batteries
and chargers
Batteries
u Never attempt to open for any reason.
u Do not expose the battery to water.
u Do not store in locations where the temperature
may exceed 40 °C.
u Charge only at ambient temperatures between
10 °C and 40 °C.
7
ENGLISH
u Charge only using the charger provided with the
tool.
u When disposing of batteries, follow the
instructions given in the section “Protecting the
environment”.
p
Do not attempt to charge damaged batteries.
Chargers
u Use your Stanley charger only to charge the
battery in the tool with which it was supplied.
Other batteries could burst, causing personal
injury and damage.
u Never attempt to charge non-rechargeable
batteries.
u Have defective cords replaced immediately.
u Do not expose the charger to water.
u Do not open the charger.
u Do not probe the charger.
$
The charger is intended for indoor use only.
+
Read the instruction manual before use.
Electrical safety
#
Your charger is double insulated; therefore
no earth wire is required. Always check
that the mains voltage corresponds to the
voltage on the rating plate. Never attempt
to replace the charger unit with a regular
mains plug.
u If the supply cord is damaged, it must be
replaced by the manufacturer or an authorised
Stanley Service Centre in order to avoid a
hazard.
Features
This tool includes some or all of the following
features.
1. On/Off switch
2. Variable speed dial
3. Tool free accessory clamping lever
4. LED Work light
Assembly
Fitting and removing the accessories
(g. A - F)
Warning! Before tting an accessory, disconnect
the tool from the mains supply.
Fitting a Stanley Fat Max accessory (g. A - C)
u Hold the tool and squeeze the accessory
clamping lever (3).
u Slide the accessory (6) between the shaft and
the accessory holder making sure the
accessory engages all eight pins on the holder
and is ush with the shaft.
u Release the accessory clamping lever.
Note: Some accessories, such as scrapers and
blades can be mounted at an angle if required (g.
C).
Removing accessory (g. A)
u Hold the tool and squeeze the accessory
clamping lever (3).
u Pull the accessory from the tool making sure
the accessory dis-engages from all eight pins
on the holder.
u Release the accessory clamping lever.
Warning: Gloves must be worn when removing
accessories as then may become hot during use.
Fitting a sanding sheet (g. D)
u Line up the sanding sheet (7) with the sanding
base (8) as shown.
u Press the sheet rmly and evenly onto the
sanding base, making sure that the holes in the
sheet coincide with the holes in the base.
Removing a sanding sheet
u Pull the sanding sheet off the sanding base (8).
Warning! Never use the sanding base without a
sanding sheet or accessory in place.
Fitting alternative accessories (g. E)
u Place the spacer (11) onto the collar (12).
u Place the alternative accessory (13) onto the
collar (12).
u Firmly attach the xing bolt (14) into place to
ensure a tight t for the alternative accessory
(13).
Note: The spacer and xing bolt are not used to
attach Stanley Fat Max accessories. Black and
decker accessories are attached using the Su-
per-lokTM Tool free accessory clamping lever.
8
ENGLISH
Fitting and removing the battery (g. F)
u To t the battery (4), line it up with the
receptacle on the tool. Slide the battery into the
receptacle and push until the battery snaps into
place.
u To remove the battery, push the release buttons
(15) while at the same time pulling the battery
out of the receptacle.
Use
Warning! Let the tool work at its own pace. Do not
overload.
Warning! Before cutting into walls, oors or ceil-
ings, check for the location of wiring and pipes.
Charging the battery (g. H)
The battery needs to be charged before rst use
and whenever it fails to produce sufcient power
on jobs that were easily done before. The battery
may become warm while charging; this is normal
and does not indicate a problem.
Warning! Do not charge the battery at ambient
temperatures below 10 °C or above 40 °C. Recom-
mended charging temperature: approx. 24 °C.
Note: The charger will not charge a battery if
the cell temperature is below approximately
0 °C or above 40 °C.The battery should be left
in the charger and the charger will begin to
charge automatically when the cell temperature
warms up or cools down.
u To charge the battery (4), insert it into the
charger (16). The battery will only t into the
charger in one way. Do not force. Be sure that
the battery is fully seated in the charger.
u Plug in the charger and switch on at the mains.
The charging indicator (17) will blink.The
charge is complete when the charging indicator
(17) switches to continuously on. The charger
and the battery can be left connected
indenitely. The LED will switch on as the
charger occasionally tops up the battery
charge.
u Charge discharged batteries within 1 week.
Battery life will be greatly diminished if stored in
a discharged state.
Leaving the battery in the charger
The charger and battery pack can be left connect-
ed with the LED glowing indenitely. The charger
will keep the battery pack fresh and fully charged.
Charger diagnostics
If the charger detects a weak or damaged battery,
the charging indicator (17) will ash red at a fast
rate. Proceed as follows:
u Re-insert the battery (4).
u If the charging indicators continues ashing red
at a fast rate, use a different battery to
determine if the charging process works
properly.
u If the replaced battery charges correctly, the
original battery is defective and should be
returned to a service centre for recycling.
u If the new battery gives the same indication as
the original battery, take the charger to be
tested at an authorised services centre.
Note: It may take as long as 60 minutes to
determine that the battery is defective. If the
battery is too hot or too cold, the LED will
alternately blink red, fast and slow, one ash at
each speed and repeat.
Variable speed control (g. H)
The variable speed control allows you to adapt the
speed of the tool to the application.
u Set the variable speed dial (2) to the desired
setting. At setting 1 the tool will operate at low
speed, 8,000 min-1. At setting 6 the tool will
operate at the maximum speed, 18,000 min-1.
Switching on and off (g. I)
u To switch the tool on, slide the on/off switch (1)
forward (position I).
u To switch the tool off, slide the on/off switch (1)
to the rear (position O).
LED work light
The LED work light (5) is activated automatically
when the tool is switched on.
Low-battery Indicator
If the LED worklight (5) begins to rapidly and
continuously ash when the switch on the tool is
depressed, the battery-pack power has run out,
and the battery pack should be recharged.
Unlike other battery pack types, Lithium-Ion battery
packs deliver fade-free power for their entire run
time. The tool will not experience a slow, gradual
loss of power as you work. To signal that the bat-
tery pack is at the end of its run time and needs to
9
ENGLISH
be charged, the power to the tool will drop quickly.
Note: The LED may also ash due to an over-
load or high temperature (see Battery Protec-
tion).
Hints for optimum use
u Always hold the tool securely. For precision
work, hold the tool near the front.
u Clamp the workpiece whenever possible,
especially when using cutting blades.
u Do not exert too much pressure on the tool.
u Always use the appropriate type of attachment
for the workpiece material and type of cut.
u Regularly check the condition of accessories.
Replace when necessary.
u Mark the desired starting point.
u Switch the tool on and slowly feed attachments
into the workpiece at the desired starting point.
u Clamp a piece of plywood or soft wood to the
back of the workpiece and saw through the
combination in order to obtain a clear cut.
u Do not force the cutting blade into the
workpiece. Note that cutting sheet metal will
normally take more time than sawing thicker
wooden workpieces.
u When cutting metal spread a thin lm of oil
along the cutting line before cutting.
Accessories
This tool includes some or all of the following
accessories.The performance of your tool depends
on the accessory used. Stanley accessories are
engineered to high quality standards and designed
to enhance the performance of your tool. By using
these accessories you will get the very best from
your tool.
Precision plunge cut saw blade for
wooden materials, soft plastics.
Sepatating, plunge and ush cutting of wood
and soft plastics. Ideal for working on doors,
skirting boards, windowsills and ooring.
Plunge cut saw blade for wood and
metal.
Sepatating, plunge and ush cutting of wood,
plastics, thin-walled non-ferrous pipes and
extrusions, nails and screws.
Plunge cut saw blade for wood and
metal.
Sepatating, plunge and ush cutting of wood,
plastics, thin-walled non-ferrous pipes and
extrusions.
Segmented saw blade.
Long life blade which is ideal for cutting wood,
plastics, thin walled ferrous and non-ferrous
material.
Rigid scraper.
Ideal for removal of hard and soft material
from at surfaces such as the removal of vinyl
ooring, bonded carpet adhesive, tile oor
adhesive,grout, paint and varnish.
Flexible scraper.
Ideal for removal of elastomer materials from
hard at surfaces in difcult to reach areas such
as silicon sealant and other caulking materials.
Carbide Grout Removal Blade.
Carbide coated surface ideal for clearing grout
and tile adhesive from at surfaces and for
fast stock removal of wood, chipboard and
breglass.
Carbide rasp.
Carbide Coated Surface Ideal For Grout Re-
moval And For Fast Stock Removal Of Plastics,
Chipgoard And Fibreglass.
Sanding Sheets.
Various grades for sanding of wood, painted and
varnished surfaces.
Maintenance
Your Stanley corded/cordless appliance/tool has
been designed to operate over a long period of
time with a minimum of maintenance. Continuous
satisfactory operation depends upon proper tool
care and regular cleaning.
Warning! Before performing any maintenance on
corded/cordless power tools:
u Switch off and unplug the appliance/tool.
u Or switch off and remove the battery from the
appliance/tool if the appliance/tool has a
separate battery pack.
u Or run the battery down completely if it is
integral and then switch off.
u Unplug the charger before cleaning it. Your
charger does not require any maintenance
apart from regular cleaning.
u Regularly clean the ventilation slots in your
appliance/tool/charger using a soft brush or dry
cloth.
u Regularly clean the motor housing using a
10
ENGLISH
damp cloth. Do not use any abrasive or
solvent-based cleaner.
u Regularly open the chuck and tap it to remove
any dust from the interior (when tted).
Protecting the environment
Separate collection. This product must
not be disposed of with normal household
waste.
Should you nd one day that your Stanley product
needs replacement, or if it is of no further use to
you, do not dispose of it with household waste.
Make this product available for separate collection.
Separate collection of used products and
packaging allows materials to be recycled
and used again. Re-use of recycled mate-
rials helps prevent environmental pollution
and reduces the demand for raw materials.
Local regulations may provide for separate collec-
tion of electrical products from the household, at
municipal waste sites or by the retailer when you
purchase a new product.
Batteries
Z
Stanley batteries can be recharged many
times. At the end of their useful life,
discard batteries with due care for our
environment.
Service Information
Stanley offers a full network of company-owned
and authorized service locations throughout Asia.
All Stanley Service Centers are staffed with trained
personnel to provide customers with efcient
and reliable power tool service.Whether you
need technical advice, repair, or genuine factory
replacement parts, contact the Stanley location
nearest to you.
Notes
u Stanley’s policy is one of continuous
improvement to our products and, as such, we
reserve the right tochange product
specications without prior notice.
u Standard equipment and accessories may vary
by country.
u Product specications may differ by country.
u Complete product range may not be available in
all countries. Contact your local Stanley dealers
for range availability.
11
18V
STCT1830
STCT1830
V 18
/
min
-1
8000-18000
1.4 2.8
kg 1.4
90588647(KR) 90600163(TW)
V AC 220 110
V DC 18 18
A 2 2
min 60-120 60-120
STBL182L STBL184L
V DC 18 18
Ah 2.0 4.0
Stanley
/
1.
a.
b.
c.
2.
a.
b.
c.
d.
e.
f.
(RCD) RCD
3.
a.
b.
c. /
d.
12
e.
f.
g.
4.
a.
b.
c.
/
d.
e.
f.
g.
5.
a)
b)
c)
d)
6.
a)
u
u
u
u
u
u
u
u
13
/
u
u
u
u
u
u
u
u
u /
u
u
u
u
(MDF)
:
u
u
u 40 °C
u 10 °C 40 °C
u
u
p
u Stanley
u
u
$
+
14
#
u Stanley
1.
2.
3.
4.LED
A - F
Stanley A - C
u (3)
u (6)
u
C
A
u (3)
u
u
D
u (7) (8)
u
(8)
E
u (11) (12)
u (13) (12)
u (14)
(13)
F
u (4)
u (15)
H
10 °C 4 0 °C
24 °C
0 °C 40 °C
u (4) (16)
15
u (17)
(17)
LED
u 1
LED
(17)
u (4)
u
u
u
60
LED
H
u (2)
1 8,000 min
-1
6 18,000 min
-1
1
u (1)
I
u (1)
O
LED
LED (5)
LED (5)
LED
u
u
u
u
u
u
u
u
u
u
16
Stanley
Stanley / /
/
u /
u /
/
u
u
u / /
u
u
Stanley
17
Z
Stanley
Stanley
Stanley
Stanley
u Stanley
u /
u
u /
Stanley
: ()
: 1204F
: 02-28201065
:
: 137
: 02-29994633
18
STCT1830
STCT1830
V 18
/
-1
8000-18000
1.4 2.8
kg 1.4
90588647(KR) 90600163(TW)
V AC 220 110
V DC 18 18
A 2 2
60-120 60-120
STBL182L STBL184L
V DC 18 18
Ah 2.0 4.0
.
,
, , , /
.
.
!
.
, /
.
. "
"
() ()
.
1.
a. .
.
b. ,
.
c.
.
.
2.
a.
.
. ( )
.
.
b. , ,
.
,
.
c.
.
.
d. .
. , ,
.
e.
.
.
f.
(RCD)
. RCD
.
3.
a.
.
, ,
.
.
b. .
. ,
,
.
19
c. . /
.
.
d.
.
.
e. .
.
.
f. .
. ,
. ,
.
g.
,
.
.
4.
a. .
.
.
b. /
.
.
c.
/
.
.
d.
,
.
.
e. .
,
.
.
.
f.
.
.
g. ,
.
.
5.
a)
.
.
b)
.
.
c) , ,
, , ,
.
.
d)
.
.
.
.
6.
a)
.
.
!
u
. "
"
" "
.
u
.
.
20
!
.
.
u .
u
.
u .
u
.
u
.
u
.
.
u
.
.
u .
.
.
u .
.
.
u ,
.
u
. .
u . ,
.
u ,
( )
.
.
u
.
.
,
.
.
.
u .
u , .
u .
.
u .
u
(: , ,
MDF ).
.
:
! ,
.
u
.
u .
u 40 °C
.
u 10 °C - 40 °C
.
u
.
u " "
.
p
.
u
.
.
u
.
u .
u .
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
