DeWalt DCS355 ユーザーマニュアル

DCS355

B

Copyright DeWALT

English (original instructions) 5

简体中文 16

繁體中文 25

한국어

34

1

Figure 1

Figure 2

a

d

f

c

e

b

g

t

i

h

j

2

Figure 4

Figure 6

x

w

Figure 5

Figure 7

k

y

p

l

v

c

Figure 3

3

Figure 13

Figure 8

Figure 11

Figure 14

f

g

f

g

a

n

g

n

g

Figure 9

Figure 10

Figure 12

e

m

o

r

f

4

Figure 17

Figure 18 Figure 19

q

s

w

e

m

q

o

r

a

d

b

Figure 15 Figure 16

English

5

Congratulations!

You have chosen a DeWALT tool. Years of experience, thorough product development and innovation make

DeWALT one of the most reliable partners for professional power tool users.

Technical Data

DCS355

Voltage V

DC

18

Battery Type Li-Ion

Oscillating frequency min-

1

0 – 20 000

Oscillating angle 1.6˚

Weight kg 1.1

Battery pack DCB180 DCB181 DCB182 DCB183

CORDLESS OSCILLATING MULTI-TOOL

DCS355

Battery type Li-Ion Li-Ion Li-Ion Li-Ion

Voltage V

DC

18 18 18 18

Capacity A

h

3.0 1.5 4.0 2.0

Weight kg 0.64 0.35 0.61 0.40

Charger DCB105

Mains voltage V

AC

220-240 V

Battery type Li-Ion

Approx. charging time min 30 40 55 70

(1.5 Ah (2.0 Ah (3.0 Ah (4.0 Ah

battery packs) battery packs) battery packs) battery packs)

Weight kg 0.49

Deﬁnitions: Safety Guidelines

The definitions below describe the level of severity

for each signal word. Please read the manual and

pay attention to these symbols.

DANGER: Indicates an imminently

hazardous situation which, if not avoided,

will result in death or serious injury.

WARNING: Indicates a potentially

hazardous situation which, if not

avoided, could result in death or

serious injury.

CAUTION: Indicates a potentially

hazardous situation which, if not

avoided, may result in minor or

moderate injury.

NOTICE: Indicates a practice not

related to personal injury which, if

not avoided, may result in property

damage.

Denotes risk of electric shock.

Denotes risk of fire.

WARNING: To reduce the risk of injury,

read the instruction manual.

General Power Tool Safety Warnings

WARNING! Read all safety warnings

and all instructions. Failure to follow

the warnings and instructions may result

in electric shock, fire and/or serious

injury.

6

English

b) Use personal protective equipment.

Always wear eye protection. Protective

equipment such as dust mask, non-skid

safety shoes, hard hat, or hearing protection

used for appropriate conditions will reduce

personal injuries.

c) Prevent unintentional starting. Ensure

the switch is in the off position before

connecting to power source and/or

battery pack, picking up or carrying the

tool. Carrying power tools with your finger

on the switch or energising power tools that

have the switch on invites accidents.

d) Remove any adjusting key or wrench

before turning the power tool on. A

wrench or a key left attached to a rotating

part of the power tool may result in personal

injury.

e) Do not overreach. Keep proper

footing and balance at all times. This

enables better control of the power tool in

unexpected situations.

f) Dress properly. Do not wear loose

clothing or jewellery. Keep your hair,

clothing and gloves away from moving

parts. Loose clothes, jewellery or long hair

can be caught in moving parts.

g) If devices are provided for the connection

of dust extraction and collection facilities,

ensure these are connected and properly

used. Use of dust collection can reduce

dust-related hazards.

4) POWER TOOL USE AND CARE

a) Do not force the power tool. Use the

correct power tool for your application.

The correct power tool will do the job

better and safer at the rate for which it

was designed.

b) Do not use the power tool if the switch

does not turn it on and off. Any power

tool that cannot be controlled with the switch

is dangerous and must be repaired.

c) Disconnect the plug from the power

source and/or the battery pack from

the power tool before making any

adjustments, changing accessories, or

storing power tools. Such preventive safety

measures reduce the risk of starting the

power tool accidentally.

d) Store idle power tools out of the reach

of children and do not allow persons

unfamiliar with the power tool or these

instructions to operate the power tool.

Power tools are dangerous in the hands of

untrained users.

Save all warningS and inStructionS

for future reference

The term “power tool” in the warnings refers to

your mains-operated (corded) power tool or

battery-operated (cordless) power tool.

1) WORK AREA SAFETY

a) Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of

flammable liquids, gases or dust. Power

tools create sparks which may ignite the dust

or fumes.

c) Keep children and bystanders away while

operating a power tool. Distractions can

cause you to lose control.

2) ELECTRICAL SAFETY

a) Power tool plugs must match the outlet.

Never modify the plug in any way. Do

not use any adapter plugs with earthed

(grounded) power tools. Unmodified plugs

and matching outlets will reduce risk of

electric shock.

b) Avoid body contact with earthed or

grounded surfaces such as pipes,

radiators, ranges and refrigerators. There

is an increased risk of electric shock if your

body is earthed or grounded.

c) Do not expose power tools to rain or wet

conditions. Water entering a power tool will

increase the risk of electric shock.

d) Do not abuse the cord. Never use the

cord for carrying, pulling or unplugging

the power tool. Keep cord away from

heat, oil, sharp edges or moving parts.

Damaged or entangled cords increase the

risk of electric shock.

e) When operating a power tool outdoors,

use an extension cord suitable for outdoor

use. Use of a cord suitable for outdoor use

reduces the risk of electric shock.

f) If operating a power tool in a damp

location is unavoidable, use a residual

current device (RCD) protected supply.

Use of an RCD reduces the risk of electric

shock.

3) PERSONAL SAFETY

a) Stay alert, watch what you are doing and

use common sense when operating a

power tool. Do not use a power tool while

you are tired or under the influence of

drugs, alcohol or medication. A moment of

inattention while operating power tools may

result in serious personal injury.

7

English

persons within or entering the work

area are also protected.

WARNING: Use this tool in a well-

ventilated area when sanding ferrous

metals. Do not operate the tool near

flammable liquids, gases or dust.

Sparks or hot particles from sanding

or arcing motor brushes may ignite

combustible materials.

Sanding Paint

WARNING: Observe the applicable

regulations for sanding paint. Pay

special attention to the following:

• Wheneverpossible,useavacuumextractor

for dust collection.

• Takespecialcarewhensandingpaintwhich

is possibly lead based:

– Do not let children or pregnant women

enter the work area.

– All persons entering the work area should

wear a mask specially designed for

protection against lead paint dust and

fumes.

– Do not eat, drink or smoke in the

work area.

• Disposeofdustparticlesandanyother

removal debris safely.

 • Hold power tool by insulated gripping

surfaces when performing an operation

where the cutting tool may contact hidden

wiring or its own cord. Contact with a "live"

wire will make exposed metal parts of the tool

"live" and shock the operator.

 • Use clamps or another practical way to

secure and support the workpiece to a

stable platform. Holding the work by hand or

against your body leaves it unstable and may

lead to loss of control.

Residual Risks

In spite of the application of the relevant safety

regulations and the implementation of safety

devices, certain residual risks cannot be avoided.

These are:

– Impairment of hearing.

– Risk of personal injury due to flying particles.

– Risk of burns due to accessories becoming hot

during operation.

– Risk of personal injury due to prolonged use.

– Risk of lacerations or burns. Do not touch the

sharp edges of accessories at any time.

e) Maintain power tools. Check for

misalignment or binding of moving parts,

breakage of parts and any other condition

that may affect the power tool’s operation.

If damaged, have the power tool repaired

before use. Many accidents are caused by

poorly maintained power tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp

cutting edges are less likely to bind and are

easier to control.

g) Use the power tool, accessories and

tool bits etc., in accordance with these

instructions taking into account the

working conditions and the work to

be performed. Use of the power tool for

operations different from those intended

could result in a hazardous situation.

5) BATTERY TOOL USE AND CARE

a) Recharge only with the charger specified

by the manufacturer. A charger that is

suitable for one type of battery pack may

create a risk of fire when used with another

battery pack.

b) Use power tools only with specifically

designated battery packs. Use of any

other battery packs may create a risk of

injury and fire.

c) When battery pack is not in use, keep it

away from other metal objects like paper

clips, coins, keys, nails, screws or other

small metal objects that can make a

connection from one terminal to another.

Shorting the battery terminals together may

cause burns or a fire.

d) Under abusive conditions, liquid may be

ejected from the battery, avoid contact.

If contact accidentally occurs, flush with

water. If liquid contacts eyes, additionally

seek medical help. Liquid ejected from the

battery may cause irritation or burns.

6) SERVICE

a) Have your power tool serviced by a

qualified repair person using only identical

replacement parts. This will ensure that the

safety of the power tool is maintained.

Additional Safety Rules for

Oscillating Multi-Tool

WARNING: Take special care when

sanding some woods (e.g. beech, oak)

and metal which may produce toxic

dust. Wear a dust mask specifically

designed for protection against toxic

dust and fumes and ensure that

8

English

 • Thesechargersarenotintendedfor

any uses other than charging

DeWALT

rechargeable batteries. Any other uses

may result in risk of fire, electric shock or

electrocution.

 • Donotexposechargertorainorsnow.

 • Pullbyplugratherthancordwhen

disconnecting charger. This will reduce risk

of damage to electric plug and cord.

 • Makesurethatcordislocatedsothatitwill

not be stepped on, tripped over or otherwise

subjected to damage or stress.

 • Donotuseanextensioncordunlessit

is absolutely necessary. Use of improper

extension cord could result in risk of fire,

electric shock or electrocution.

 • Whenoperatingachargeroutdoors,always

provide a dry location and use an extension

cord suitable for outdoor use. Use of a cord

suitable for outdoor use reduces the risk of

electric shock.

 • Donotblocktheventilationslotsonthe

charger.Theventilationslotsarelocated

on the top and sides of the charger. Place

the charger in a position away from any heat

source.

 • Donotoperatechargerwithdamagedcord

or plug — have them replaced immediately.

 • Do not operate charger if it has received

a sharp blow, been dropped or otherwise

damaged in any way. Take it to an authorised

service centre.

 • Donotdisassemblethecharger;takeitto

an authorised service centre when service or

repair is required. Incorrect reassembly may

result in a risk of electric shock, electrocution or

fire.

 • Incaseofdamagedpowersupplycordthe

supply cord must be replaced immediately by

the manufacturer, its service agent or similar

qualified person to prevent any hazard.

 • Disconnectthechargerfromtheoutlet

beforeattemptinganycleaning.Thiswill

reduce the risk of electric shock. Removing

the battery pack will not reduce this risk.

• NEVERattempt to connect 2 chargers together.

 • Thechargerisdesignedtooperateon

standard220-240Vhouseholdelectrical

power. Do not attempt to use it on any other

voltage. This does not apply to the vehicular

charger.

Markings on Tool

The following pictograms are shown on the tool:

Read instruction manual before use.

DATE CODE POSITION (FIG. 1)

The date code (t), which also includes the year of

manufacture, is printed into the housing.

Example:

2013 XX XX

Year of Manufacture

Important Safety Instructions for All

Battery Chargers

SAVE THESE INSTRUCTIONS: This manual

contains important safety and operating instruc tions

for the DCB105 battery charger.

 • Beforeusingthecharger,readallinstructions

and cautionary markings on charger, battery

pack and product using the battery pack.

WARNING: Shock hazard. Do not allow

any liquid to get inside charger. Electric

shock may result.

CAUTION: Burn hazard. To reduce

the risk of injury, charge only DeWALT

rechargeable battery packs. Other types

of batteries may overheat and burst

resulting in personal injury and property

damage.

CAUTION: Children should be

supervised to ensure that they do not

play with the appliance.

NOTICE: Under certain conditions, with

the charger plugged in to the power

supply, the exposed charging contacts

inside the charger can be shorted by

foreign material. Foreign materials of

a conductive nature such as, but not

limited to, steel wool, aluminium foil or

any buildup of metallic particles should

be kept away from charger cavities.

Always unplug the charger from the

power supply when there is no battery

pack in the cavity. Unplug charger

before attempting to clean.

 • DONOTattempttochargethebatterypack

with any chargers other than the ones in

this manual. The charger and battery pack are

specifically designed to work together.

9

English

reached an appropriate temperature. The charger

then automatically switches to the pack charging

mode. This feature ensures maximum battery life.

XR Li-Ion tools are designed with an Electronic

Protection System that will protect the battery

against overloading, overheating or deep discharge.

The tool will automatically turn off if the Electronic

Protection System engages. If this occurs, place the

Li-Ion battery on the charger until it is fully charged.

A cold battery pack will charge at about half the rate

of a warm battery pack. The battery pack will charge

at that slower rate throughout the entire charging

cycle and will not return to maximum charge rate

even if the battery warms.

Important Safety Instructions for All

Battery Packs

When ordering replacement battery packs, be sure

to include the catalog number and voltage.

The battery pack is not fully charged out of the

carton. Before using the battery pack and charger,

read the safety instructions below and then follow

the charging procedures outlined.

read all inStructionS

 • Donotchargeorusethebatterypack

in explosive atmospheres, such as in the

presence of flammable liquids, gases or

dust. Inserting or removing the battery pack

from the charger may ignite the dust or fumes.

• Never force the battery pack into charger.

Do not modify the battery pack in any way

to fit into a non-compatible charger as

battery pack may rupture causing serious

personal injury.

 • Chargethebatterypacksonlyindesignated

DeWALT chargers.

• DONOTsplash or immerse in water or other

liquids.

 • Donotstoreorusethetoolandbattery

pack in locations where the temperature

may reach or exceed 40˚C (105˚F) (such as

outside sheds or metal buildings in summer).

 • Forbestresults,makesurethebatterypackis

fully charged before use.

WARNING: Never attempt to open

the battery pack for any reason. If

the battery pack case is cracked or

damaged, do not insert it into the

charger. Do not crush, drop or damage

battery pack. Do not use a batterypack

or charger that has received a sharp

blow, been dropped, run over or

damaged in any way (e.g., pierced with

Save tHeSe inStructionS

Chargers

The DCB105 charger accepts 10.8 V, 14.4 V and

18 V Li-Ion (DCB123, DCB140, DCB141, DCB142,

DCB143, DCB180, DCB181, DCB182 and

DCB183) battery packs.

This charger requires no adjustment and is designed

to be as easy as possible to operate.

Charging Procedure (ﬁg. 2)

1. Plug the charger into an appropriate 220-240 V

outlet before inserting the battery pack.

2. Insert the battery pack (h) into the charger,

making sure the pack is fully seated in the

charger. The red (charging) light will blink

continuously indicating that the charging

process has started.

3. The completion of charge will be indicated by

the red light remaining ON continuously. The

pack is fully charged and may be used at this

time or left in the charger.

NOTE: To ensure maximum performance and life of

Li-Ion batteries, charge the battery pack fully before

first use.

Charging Process

Refer to the table below for the state of charge of

the battery pack.

State of charge

charging –– –– –– ––

fully charged –––––––––––––––––

 hot/coldpackdelay ––•––•––• ––•

x

 problempackorcharger ••••••••••••

 problempowerline ••••••••••••

This charger will not charge a faulty battery pack.

The charger will indicate faulty battery by refusing to

light or by displaying problem pack or charger blink

pattern.

NOTE: This could also mean a problem with a

charger.

If the charger indicates a problem, take the charger

and battery pack to be tested at an authorised

service centre.

Hot/Cold Pack Delay

When the charger detects a battery that is too hot

or too cold, it automatically starts a hot/cold pack

delay, suspending charging until the battery has

10

English

NOTE: Battery packs should not be stored

completely depleted of charge. The battery pack will

need to be recharged before use.

Labels on Charger and Battery Pack

In addition to the pictographs used in this manual,

the labels on the charger and the battery pack show

the following pictographs:

Read instruction manual before use.

Charging.

Fully charged.

Hot/cold pack delay.

x

Problem pack or charger.

Problem powerline.

Do not probe with conductive objects.

Do not charge damaged battery packs.

Use only with DeWALT battery packs.

Others may burst, causing personal injury

and damage.

Do not expose to water.

Have defective cords replaced

immediately.

Charge only between 4˚C and 40˚C.

Discard the battery pack with due care for

the environment.

Do not incinerate the battery pack.

Charges Li-Ion battery packs.

See Technical Data for charging time.

a nail, hit with a hammer, stepped on).

Electric shock or electrocution mayresult.

Damaged battery packs should be

returned to the service centre for

recycling.

CAUTION: When not in use, place

tool on its side on a stable surface

where it will not cause a tripping or

falling hazard. Some tools with large

battery packs will stand upright on the

battery pack but may be easily knocked

over.

SPECIFIC SAFETY INSTRUCTIONS FOR LITHIUM ION

(Li-Ion)

 • Donotincineratethebatterypackevenifit

is severely damaged or is completely worn

out. The battery pack can explode in a fire.

Toxic fumes and materials are created when

lithium ion battery packs are burned.

 • Ifbatterycontentscomeintocontactwith

the skin, immediately wash the area with

mild soap and water. If the battery liquid gets

into the eye, rinse water over the open eye for

15 minutes or until irritation ceases. If medical

attention is needed, the battery electrolyte

is composed of a mixture of liquid organic

carbonates and lithium salts.

 • Contentsofopenedbatterycellsmaycause

respiratory irritation. Provide fresh air. If

symptoms persists, seek medical attention.

WARNING: Burn hazard. Battery liquid

may be flammable if exposed to spark

or flame.

Battery Pack

BATTERY TYPE

The DCS355 operates on 18 volt XR Li-Ion battery

packs.

The DCB180, DCB181, DCB182 or DCB183 battery

packs may be used. Refer to Technical Data for

more information.

Storage Recommendations

1. The best storage place is one that is cool and

dry away from direct sunlight and excess heat

or cold. For optimum battery performance and

life, store battery packs at room temperature

when not in use.

2. For long storage, it is recommended to store a

fully charged battery pack in a cool, dry place

out of the charger for optimal results.

11

English

INTENDED USE

This oscillating multi-tool is designed for professional

detail sanding, plunge cutting, flush cutting, removal

of excess materials and surface preparation

applications.

DO NOT use under wet conditions or in the

presence of flammable liquids or gases.

This oscillating multi-tool is a professional power

tool.

DO NOT let children come into contact with the

tool. Supervision is required when inexperienced

operators use this tool.

 • Thisproductisnotintendedforusebypersons

(including children) suffering from diminished

physical, sensory or mental abilities; lack of

experience, knowledge or skills unless they are

supervised by a person responsible for their

safety. Children should never be left alone with

this product.

Electrical Safety

The electric motor has been designed for one

voltage only. Always check that the battery pack

voltage corresponds to the voltage on the rating

plate. Also make sure that the voltage of your

charger corresponds to that of your mains.

Your DeWALT charger is double insulated

in accordance with EN 60335; therefore

no earth wire is required.

If the supply cord is damaged, it must be replaced

by a specially prepared cord available through the

DeWALT service organisation.

Using an Extension Cable

An extension cord should not be used unless

absolutely necessary. Use an approved extension

cable suitable for the power input of your charger

(see Technical Data). The minimum conductor size

is 1 mm

2

; the maximum length is 30 m.

When using a cable reel, always unwind the cable

completely.

ASSEMBLY AND ADJUSTMENTS

WARNING: Prior to assembly and

adjustment, always remove the

battery pack. Always switch off the

tool before inserting or removing

the battery pack. Be sure the trigger

switch is in the OFF position. An

accidental start-up can cause injury.

WARNING: Risk of lacerations or

burns. Do not touch the sharp

Only for indoor use.

Package Contents

The package contains:

1 Adaptor for all blades

1 31mm x 43mm Fastcut wood blade

1 31 mm x 43 mm Wood with nails blade

1 Blade adaptor hex key

1 Sanding-pad

25 Assorted sandpaper pieces

1 Instruction manual

**DCS355D2/DCS355M2 ONLY:

1 100mm Semicircle blade**

1 Rigid scraper blade**

1 Dust extraction adaptor**

1 Cutting guide**

1 Cutting guide hex key**

1 9.5mm x 43mm Wood detail blade**

1 3mm Carbide grout removal blade**

(100mm half moon)

1 Charger**

2 Li-Ion battery packs**

1 TStak kitbox**

NOTE: Battery packs, chargers and kitboxes are not

included with N-models.

 • Checkfordamagetothetool,partsor

accessories which may have occurred

during transport.

 • Takethetimetothoroughlyreadand

understand this manual prior to operation.

Description (ﬁg. 1, 2)

WARNING: Never modify the power

tool or any part of it. Damage or

personal injury could result.

a. Variable speed trigger

b. LED Worklight

c. Accessory clamp lever

d. Lock on/off button

e. Accessory side mount slots

f. Cut guide block

g. Cut guide arm

h. Battery pack

i. Battery release button

j. Fuel gauge button

12

English

2. Clean any residual debris from the tool shaft

and the accessory holder.

3. Slide the accessory between the shaft (v) and

the accessory holder making sure the accessory

engages all eight pins on the holder and is flush

with the shaft. Ensure the accessory is oriented

as shown in figure 4.

4. Release the accessory clamp lever.

NOTE: Some accessories, such as scrapers and

blades can be mounted at an angle if required as

shown in figure 5.

INSTALLING/REMOVING SANDING SHEETS (FIG. 6)

A diamond shaped platen uses a hook and loop

adhesion system to attach the sanding sheets. The

platen allows you to use it on large flat surfaces and

tight spots or corners.

1. Attach the sanding platen (w) as described

under Installing/Removing Accessories.

2. Align the edges on the sanding sheet, with

the edge of the sanding platen and press the

sanding sheet (x) onto the platen.

3. Firmly press the base with the sanding sheet

attached against a flat surface and briefly switch

the tool on. This provides for good adhesion

between the platen and the sanding sheet and

also helps to prevent premature wear.

4. When the tip of the sanding sheet becomes

worn, detach the sheet from the platen, rotate

and reapply.

ATTACHING ACCESSORIES USING THE UNIVERSAL

ADAPTER (FIG. 7)

CAUTION: To avoid injury, do not

use any accessory for an application

where the adaptor may fail to hold the

accessory.

CAUTION: Read and follow all

manufacturers' safety warnings for any

accessories used with this tool.

CAUTION: To avoid injury, ensure

adaptor and accessory are securely

tightened.

Non-DeWALT accessories can be attached using

the universal adaptor.

1. Place the washer (k) on the tool.

2. Place accessory (y) on to washer.

3. Tighten and secure adaptor nut (p) using hex

wrench (l).

edges of accessories at any time.

Do not touch workpiece or blade

immediately after operating the tool.

They can become very hot. Handle

carefully. Always allow accessories and

workpiece to cool before handling.

WARNING: Use only DeWALT battery

packs and chargers.

Inserting and Removing the

Battery Pack from the Tool (ﬁg. 2)

NOTE: For best results, make sure your battery

pack is fully charged.

TO INSTALL THE BATTERY PACK INTO THE TOOL HANDLE

1. Align the battery pack (h) with the rails inside the

tool’s handle (fig. 2).

2. Slide it into the handle until the battery pack is

firmly seated in the tool and ensure that it does

not disengage.

TO REMOVE THE BATTERY PACK FROM THE TOOL

1. Press the battery release button (i) and firmly

pull the battery pack out of the tool handle.

2. Insert battery pack into the charger as

described in the charger section of this manual.

FUEL GAUGE BATTERY PACKS (FIG. 2)

Some D

eWALT battery packs include a fuel gauge

which consists of three green LED lights that

indicate the level of charge remaining in the battery

pack.

To actuate the fuel gauge, press and hold the fuel

gauge button (j). A combination of the three green

LED lights will illuminate designating the level of

charge left. When the level of charge in the battery

is below the usable limit, the fuel gauge will not

illuminate and the battery will need to be recharged.

NOTE: The fuel gauge is only an indication of the

charge left on the battery pack. It does not indicate

tool functionality and is subject to variation based

on product components, temperature and end-user

application.

Installing/Removing Accessories

(ﬁg.3–7)

TOOL-FREE ACCESSORY CLAMP (FIG. 3–5)

The DCS355 features a quick change accessory

system. This allows for faster accessory changes

without the need for wrenches or hex keys like other

oscillating tool systems.

1. Grasp the tool and squeeze the accessory

clamping lever (c) as shown in figure 3.

13

English

1. Attach the dust extraction adaptor (q) by

inserting the tabs (m) in to the accessory side

mount slots (e).

NOTE: The dust extraction adaptor can be

attached to either side of the tool.

2. Insert screw (o) into the dust extraction adaptor

(q) and tighten with the supplied hex key (p).

OPERATION

Instructions for Use (ﬁg. 14, 15)

WARNING: Always observe the safety

instructions and applicable regulations.

WARNING: To reduce the risk of

serious personal injury, turn tool

off and disconnect battery pack

before making any adjustments or

removing/installing attachments or

accessories. An accidental start-up

can cause injury.

WARNING: Ensure switch is fully OFF

before installing the battery.

1. Install the battery pack.

2. To turn the tool ON, hold it as shown in

figure14 and press the variable speed

trigger(a).

NOTE: The further the trigger switch is

depressed the faster the tool will operate.

If in doubt about the proper speed for your

operation, test the performance at low speed

and gradually increase until a comfortable speed

is found.

3. To turn the tool OFF, release the variable speed

trigger (a).

Lock on/off Button (ﬁg. 15)

The tool can be locked off by fully depressing the

lock on/off button (d) shown in figure 15.

For more comfort in extended use applications, the

lock on/off button (d) can lock the trigger trigger (a)

in the depressed position.

LED Worklight (ﬁg. 16)

The LED worklight (b) will activate when the trigger

is depressed. It will automatically shut off following a

short period of time once the trigger is released.

Proper Hand Position (ﬁg. 14)

WARNING: To reduce the risk of

serious personal injury, ALWAYS use

proper hand position as shown.

Attaching the Cut Guide (ﬁg. 8–13)

The depth/cut guide allows you to precisely cut

material at a specified depth and more accurately

track a marked cut line.

1. Attach the cut guide block (f) by inserting

the accessory tabs (m) on the guide into the

accessory side mount slots (e) on the main

body of the tool.

NOTE: The depth/cut guide can be attached to

either side of the tool.

2. Secure the block to the main body with the

supplied screw (o). Tighten with the supplied

hex wrench (r).

DEPTH GUIDE

This feature allows you to precisely cut material at a

specified depth.

1. Insert the guide arm (g) as shown in figure 9 into

the front slot on the guide block (f).

2. Adjust the length of the guide by pulling out or

pushing inward to achieve the desired cut depth

as shown in figure 10.

3. Secure the guide in place by turning the depth/

cut adjustment knob (n) clockwise. To release

the guide turn the depth/cut adjustment knob

counterclockwise.

CUT GUIDE

This feature allows you to more accurately track a

marked cut line.

1. Insert the guide arm (g) as shown in figure 11

into the slots on the left and right sides of the

guide block (f).

2. Adjust the length of the guide by pulling out or

pushing inward to achieve the desired length as

shown in figure 12.

3. Secure the guide in place by turning the depth/

cut adjustment knob (n) clockwise. To release

the guide turn the depth/cut adjustment knob

counterclockwise.

NOTE: The guide arm can also be placed in the

guard assembly vertically in order to set the height

off a cut. Refer to figure 13.

Attaching the Dust Extraction

Adaptor (ﬁg. 17)

The Dust Extraction Adaptor allows you to connect

the tool to an external dust extractor, either using

the AirLock™ system (DWV9000-XJ), or a standard

35mm dust extractor fitment.

14

English

MAINTENANCE

Your DeWALT power tool has been designed to

operate over a long period of time with a minimum

of maintenance. Continuous satisfactory operation

depends upon proper tool care and regular cleaning.

WARNING: To reduce the risk of

serious personal injury, turn tool

off and disconnect battery pack

before making any adjustments or

removing/installing attachments or

accessories. Be sure the trigger switch

is in the OFF position. An accidental

start-up can cause injury.

The charger and battery pack are not serviceable.

There are no serviceable parts inside.

Lubrication

Your power tool requires no additional lubrication.

Cleaning

WARNING: Blow dirt and dust out of

the main housing with dry air as often as

dirt is seen collecting in and around the

air vents. Wear approved eye protection

and approved dust mask when

performing this procedure.

WARNING: Never use solvents or

other harsh chemicals for cleaning the

non-metallic parts of the tool. These

chemicals may weaken the materials

used in these parts. Use a cloth

dampened only with water and mild

soap. Never let any liquid get inside the

tool; never immerse any part of the tool

into a liquid.

CHARGER CLEANING INSTRUCTIONS

WARNING: Shock hazard. Disconnect

the charger from the AC outlet before

cleaning. Dirt and grease may be

removed from the exterior of the charger

using a cloth or soft non-metallic brush.

Do not use water or any cleaning

solutions.

Optional Accessories

WARNING: Since accessories, other

than those offered by DeWALT, have

WARNING: To reduce the risk of

serious personal injury, ALWAYS hold

securely in anticipation of a sudden

reaction.

Proper hand position requires the tool to be held as

shown in figure 14.

Using the Dust Extraction Adaptor

with the Sanding Platen (ﬁg. 18)

1. Attach the dust extraction adaptor (q). Refer to

Attaching the Dust Extraction Adaptor.

2. Attach the sanding platen (w) as described

under Installing/Removing Accessories.

3. Attach sanding sheet as described under

Installing/Removing Sanding Sheets.

Using the Dust Extraction Adaptor

with Plunge Cutting Accessory

(ﬁg.19)

1. Attach the dust extraction adaptor. Refer to

Attaching the Dust Extraction Adaptor.

2. Push dust extraction arm (s) into the lower

aperture of the dust extraction adaptor (q).

3. Attach plunge cutting blade as described under

Installing/Removing Accessories.

4. Adjust the dust extraction arm (s) for best

results.

Helpful Hints

 • Alwaysensuretheworkpieceisfirmlyheldor

clamped to prevent movement. Any movement

of the material may affect the quality of the

cutting or sanding finish.

 • Donotstartsandingwithouthavingthe

sandpaper attached to sanding platen.

 • Usecoarsegritpapertosandroughsurfaces,

medium grit for smooth surfaces and fine grit for

the finishing surfaces. If necessary, first make a

test run on scrap material.

 • Excessiveforcewillreducetheworking

efficiency and cause motor overload. Replacing

the accessory regularly will maintain optimum

working efficiency.

 • Donotallowthesandpapertowearaway,itwill

damage the sanding pad.

 • Ifthetooloverheats,especiallywhenusedat

low speed, set the speed to maximum and

run it with no load for 2–3 minutes to cool

the motor. Avoid prolonged usage at very low

speeds. Always keep the blade sharp.

15

English

advantage of this service please return your product

to any authorised repair agent who will collect them

on our behalf.

You can check the location of your nearest

authorised repair agent by contacting your local

DeWALT office at the address indicated in this

manual. Alternatively, a list of authorised DeWALT

repair agents and full details of our after-sales

service and contacts are available on the Internet at:

www.2helpU.com.

Rechargeable Battery Pack

This long life battery pack must be recharged when

it fails to produce sufficient power on jobs which

were easily done before. At the end of its technical

life, discard it with due care for our environment:

 • Runthebatterypackdowncompletely,then

remove it from the tool.

 • Li-Ioncellsarerecyclable.Takethemtoyour

dealer or a local recycling station. The collected

battery packs will be recycled or disposed of

properly.

not been tested with this product, use

of such accessories with this tool could

be hazardous. To reduce the risk of

injury, only D

eWALT, recommended

accessories should be used with this

product.

Consult your dealer for further information on the

appropriate accessories.

COMPATIBLE ACCESSORIES

Oscillating sanding pad

Oscillating wood w/ nails blade

Wide titanium oscillating wood w/ nails blade

Oscillating hardwood blade

Oscillating fastcut wood blade

Wide oscillating fastcut wood blade

Oscillating wood detail blade

Oscillating titanium metal blade

Oscillating semicircle blade

Oscillating titanium semicircle blade

Oscillating flush cut blade

Titanium oscillating flush cut blade

Oscillating multi-material blade

Oscillating rigid scraper blade

Oscillating flexible scraper blade

Oscillating carbide grout removal blade

Oscillating fastcut carbide grout removal blade

Oscillating carbide rasp

Protecting the Environment

Separate collection. This product must

not be disposed of with normal

household waste.

Should you ﬁnd one day that your DeWALT product

needs replacement, or if it is of no further use to you,

do not dispose of it with household waste. Make this

product available for separate collection.

Separate collection of used products and

packaging allows materials to be

recycled and used again. Re-use of

recycled materials helps prevent

environmental pollution and reduces

the demand for raw materials.

Local regulations may provide for separate collection

of electrical products from the household, at

municipal waste sites or by the retailer when you

purchase a new product.

D

eWALT provides a facility for the collection and

recycling of DeWALT products once they have

reached the end of their working life. To take

16

中文简体

DEWALT DEWALT

DCS355

18

/ 0 – 20 000

1.6˚

1.1

电池组 DCB180 DCB181 DCB182 DCB183

DCS355

18 18 18 18

3.0 1.5 4.0 2.0

0.64 0.35 0.61 0.40

充电器 DCB105

220

30 40 55 70

(1.5 Ah (2.0 Ah (3.0 Ah (4.0 Ah

) ) ) )

0.49

17

中文简体

4)

a)

b)

c)

d)

e)

f)

g)

5)

a)

b)

c)

d)

6)

a)

1)

a)

b)

c)

2)

a)

b)

c)

d)

e)

f)

RCD

3)

a)

b)

c) /

d)

e)

f)

g)

18

中文简体

•

DEWALT

•

• DEWALT

•

–

•

–

1

(t)

2013 XX XX

DCB105

ページが読み込まれています...

DeWalt DCS355 ユーザーマニュアル

DeWalt DCS355 ユーザーマニュアル

他の言語で

関連論文

その他のドキュメント