Hitachi RAS-13EX9KS2 ユーザーマニュアル

SPLIT TYPE

INDOOR UNIT/OUTDOOR UNIT

MODEL

RAS-13EX9KS2 / RAC-13EX9G

RAS-18EX9KS2 / RAC-18EX9G

Instruction Manual Page 1~40

To obtain the best performance and ensure years of trouble free use, please read this instruction manual

completely.

RAC-13EX9G

OUTDOOR UNIT

INDOOR UNIT

RAS-13EX9KS2

RAS-18EX9KS2

RAC-18EX9G

使用說明書 41~80頁

請詳細閱讀這本使用說明書以了解正確的使用法，使機器長久發揮最高性能。

RAS13EX9KS2_EN_CH(1-10).p65 3/8/07, 3:39 PM1

WARNING

SAFETY PRECAUTION

• Please read the “Safety Precaution” carefully before operating the unit to ensure correct usage of the unit.

• Pay special attention to signs of “ Warning” and “ Caution”. The “Warning” section contains matters

which, if not observed strictly, may cause death or serious injury. The “Caution” section contains matters

which may result in serious consequences if not observed properly. Please observe all instructions

strictly to ensure safety.

• The signs indicate the following meanings.

Make sure to connect earth line.

This sign in the figure indicates prohibition.

Indicates the instructions that must be followed.

• Please keep this manual after reading.

PRECAUTIONS DURING INSTALLATION

WARNING

CAUTION

• Do not reconstruct the unit.

Water leakage, fault, short circuit or fire may occur if you reconstruct the

unit by yourself.

• Please ask your sales agent or qualified technician for the installation of your unit.

Water leakage, short circuit or fire may occur if you install the unit by yourself.

• Please use earth line.

Do not place the earth line near water or gas pipes, lightning-conductor, or

the earth line of telephone. Improper installation of earth line may cause

electric shock.

• A circuit breaker should be installed depending on the mounting site of

the unit. Without a circuit breaker, the danger of electric shock exists.

• Do not install the unit near location where there is flammable gas.

The outdoor unit may catch fire if flammable gas leaks around it.

• Please ensure smooth flow of water when installing the drain hose.

PRECAUTIONS DURING SHIFTING OR MAINTENANCE

• Should abnormal situation arise (like burning smell), please stop operating

the unit and turn off the circuit breaker. Contact your agent. Fault, short

circuit or fire may occur if you continue to operate the unit under abnormal

situation.

• Please contact your agent for maintenance.

Improper self maintenance may cause electric shock and fire.

• Please contact your agent if you need to remove and reinstall the unit.

Electric shock or fire may occur if you remove and reinstall the unit yourself improperly.

PRECAUTIONS DURING OPERATION

W

A

R

N

I

N

G

• Avoid an extended period of direct air flow for your health.

• Do not put objects like thin rods into the panel of blower and suction side because

the high-speed fan inside may cause danger.

• Do not use any conductor as fuse wire, this could cause fatal accident.

• During thunder storm, please stop operating the unit and turn off the circuit breaker.

“OFF”

– 2 –

RAS13EX9KS2_EN_CH(1-10).p65 3/8/07, 3:40 PM2

ENGLISH

BAHASA MELAYU

THAILAND

– 3 –

• The product shall be operated under the manufacturer specification and not for

any other intended use.

• Do not attempt to operate the unit with wet hands. This could cause fatal accident.

• When operating the unit with burning equipment, regularly ventilate the room to

avoid oxygen insufficiency.

• Do not direct the cool air coming out from the air-conditioner panel to face

household heating apparatus as this may affect the working of apparatus such

as the electric kettle, oven etc.

• Please ensure that outdoor mounting frame is always stable, firm and without

defect. If not, the outdoor unit may collapse and cause danger.

• Do not splash or direct water to the body of the unit when cleaning it as this may

cause short circuit.

• Do not use any aerosol or hair sprays near the indoor unit. This chemical can

adhere on heat exchanger fin and blocked the evaporation water flow to drain

pan. The water will drop on tangential fan and cause water splashing out from

indoor unit.

• Please switch off the unit and turn off the circuit breaker during cleaning, the high-

speed fan inside the unit may cause danger.

• Turn off the circuit breaker if the unit is not to be operated for a long period.

• Do not climb on the outdoor unit or put objects on it.

• Do not water container (like vase) on the indoor unit to avoid water dripping onto

the unit. Dripping water will damage the insulator inside the unit and causes short-

circuit.

• Do not place plants directly under the air flow as it is bad for the plants.

• When operating the unit with the door and windows opened, (the room humidity is always

above 80%) and with the air deflector facing down or moving automatically for a long period of

time, water will condense on the air deflector and drips down occasionally. This will wet your

furniture. Therefore, do not operate under such condition for a long time.

• If the amount of heat in the room is above the cooling or heating capability of the unit (for

example: more people entering the room, using heating equipments and etc.), the preset room

temperature cannot be achieved.

PRECAUTIONS DURING OPERATION

C

A

U

T

I

O

N

“OFF”

RAS13EX9KS2_EN_CH(1-10).p65 3/8/07, 3:40 PM3

– 4 –

NAMES AND FUNCTIONS OF EACH PART

DRAIN PIPE

Condensed water drain to outside.

CONNECTING CORD

AIR INLET (BACK)

AIR OUTLET

MODEL NAME AND DIMENSIONS

INDOOR UNIT

OUTDOOR UNIT

DRAIN PIPE

Condensed water drain to outside.

CONNECTING CORD

AIR INLET (BACK)

AIR OUTLET

RAC-18EX9G

RAC-13EX9G

MODEL

WIDTH (mm)

HEIGHT (mm)

DEPTH (mm)

RAS-13EX9KS2 / RAS-18EX9KS2

RAC-13EX9G

RAC-18EX9G

870

700

850

298

570

800

223

210

298

Fresh Air In Exhaust Fan (Internal)

This operates during the fresh air in, exhaust,

2-way exchange and Nano-titanium air

purifying operation.

Nano-Titanium Air Purifying Unit (Internal)

This traps cigarette smoke, pollen, etc.

(Refer page 29)

Pre-Filter (Internal)

To prevent dust from coming into

the indoor unit.

(Refer page 29)

Air Outlet

Horizontal Deflector/

Vertical Deflector (Internal)

Front Panel

(Refer to pages 29, 33)

Fresh Air Window

This blows air from outside into the room

while the fresh air in is operating.

This blows air in the room during 2-way

exchange and Nano-titanium air purifying

operation.

Display

(Refer page 5)

Signal Receiver

Receive the

signal from the

remote

controller.

Power Plug

Top Grill

(Refer page 34)

Movable Panel

This panel opens during the operation

and closes when operation stop.

RAS13EX9KS2_EN_CH(1-10).p65 3/8/07, 3:40 PM4

ENGLISH

BAHASA MELAYU

THAILAND

– 5 –

INDOOR UNIT INDICATORS

OPEN THE FRONT PANEL

●

AIR MONITOR LAMP (yellow)

This lamp lights when the air monitor is set.

●

FILTER LAMP (green)

●

SUPER COOL LAMP (yellow)

●

TWO WAY AIR EXCHANGE LAMP (green)

This lamp lights when the fresh air in and exhaust

are operating.

●

OPERATION LAMP (yellow)

This lamp lights during operation.

●

TIMER LAMP (orange)

This lamp lights when the timer is working.

■ Turn off the device before opening the front panel.

Open the Front Panel

Hold both sides of the front panel and lift

up. Do not hold the movable panel when

opening and closing the front panel.

Front panel

Movable panel

Hold both sides of the front panel and lift

up.

Nano Titanium

RAS13EX9KS2_EN_CH(1-10).p65 3/8/07, 3:40 PM5

– 6 –

NAMES AND FUNCTIONS OF EACH PART

DUCT FILTER

INDOOR UNIT CONTROL PANEL

■ Operate after opening the front panel. (How to open the front panel, refer to page 5.)

Temporary Switch

If the remote controller does not work due to battery

failure, press this switch to start and stop operation.

• This temporary operation will be at the most recent

setting mode. (The unit will immediately go into

automatic operation once power is switched on.)

✩ If the power stays on and the unit is not operated, power is slightly consumed in the control circuit.

The power is saved by turning off the circuit breaker.

CAUTION

Turn off the circuit breaker or pull

out the power plug if the unit is not

in use for a long period.

Nano-Titanium Disinfecting/

Deodorizing/Dust Collecting

Fresh Air In Filter

This disinfects, deodorizes and

eliminates dust from the air

ventilated from the outside.

(Refer to pages 29, 32)

Fresh Air in Filter

This traps dirt and dust particles

in the air ventilated from the

outside. (Refer to pages 29, 32)

Two Way Air Exchange

Selection Switch

Select one of the following:

“Prohibit Two Way Air

Exchange”, “Only Exhaust”,

and “Operate Two Way Air

Exchange”.

Dirt Sensor

The Dirt Sensor detects

cigarette smoke etc. (Refer

page 18)

TEMPORARY

SWITCH

FORCE

COOL

PUSH AND HOLD THE SWITCH FOR 3 SEC

TO START THE FORCE COOL OPERATION.

FOR SERVICE MAN USE ONLY

Front Panel

Force Cool (For service man use only)

RAS13EX9KS2_EN_CH(1-10).p65 3/8/07, 3:40 PM6

ENGLISH

BAHASA MELAYU

THAILAND

– 7 –

Signal Emitting Window / Transmission Sign

Point this window toward the indoor unit when

controlling it. The transmission sign blinks when a

signal is sent.

Display

This indicates the room temperature selected, current time,

timer and intensity of circulation selected.

START / STOP Button

Press this button to start operation. Press it again to

stop operation.

SLEEP Button

Use this button to set the sleep timer.

SUPER COOLING Button

Press this button to start super cooling mode.

SILENT Button

Press this button to start silent mode.

FAN Button

Use this button to increase and decrease fan

speed.

TEMPERATURE Button

Use this button to raise or lower the temperature setting.

(Keep pressing and the value will change more quickly.)

EXHAUST Button

FRESH AIR IN Button

AUTOMATIC TWO WAY AIR EXCHANGE Button

Press this button to set the automatic two way air

exchange mode.

NAMES AND FUNCTIONS OF REMOTE CONTROL

REMOTE CONTROL :

This controls the operation of the indoor unit. The range of control is

about 7 meters. If indoor lighting is controlled electronically, the range of control may be

shorter. Before fixing it, make sure the indoor unit can be controlled from the remote controller.

RAS13EX9KS2_EN_CH(1-10).p65 3/8/07, 3:40 PM7

– 8 –

NAMES AND FUNCTIONS OF REMOTE CONTROL

FUNCTION Selector

Use this button to select the operating mode. Every

time you press this button, the mode will change from

AUTO → COOL → DEHUMIDIFY →

CIRCULATION → FAN cyclically.

AIR PURIFIER Button

Press this button to start the air purifier mode.

TWIN AIR FLOW Button

Use this button to allow two different air flows circulate

in every corner of room efficiently.

PARALLEL WING Button

Use this button to control angle of the vertical air

deflector to parallel.

AUTO SWING Button

Controls the angle of the horizontal air defelctor.

FILTER Button

Press this button when you have cleaned the filter.

About 100 hour after this, the FILTER lamp will light to

indicate that it is the time to clean the filter.

TIMER Control

Use these buttons to set the timer.

RESERVE Button

Time setting reservation.

CANCEL Button

Cancel time reservation.

TIME Button

Use this button to set and check the time.

RESET Button

Press this button after the batteries are replaced or

when some irregular operation is found.

OFF-TIMER Button

Select the turn OFF time.

ON-TIMER Button

Select the turn ON time.

• Do not put the remote controller in the following places.

• Under direct sunlight.

• In the vicinity of a heater.

• Handle the remote controller carefully. Do not drop it on the floor, and protect it from water.

• Once the outdoor unit stops, it will not restart for about 3 minutes (unless you turn the power

switch off and on or unplug the power cord and plug it in again). This is to protect the device and

does not indicate a failure.

• If you press the FUNCTION selector button during operation, the device may stop for about 3

minutes for protection.

Precautions for Use

RAS13EX9KS2_EN_CH(1-10).p65 3/8/07, 3:40 PM8

ENGLISH

BAHASA MELAYU

THAILAND

– 9 –

Increase

decrease

MANUAL OPERATION

Press the to select the Operating Mode.

Either

(AUTO), (COOL), (DEHUMIDIFY),

(CIRCULATION), (FAN).

1

To set the Fan Speed.

Press

(FAN SPEED) button to select AUTO, HI,

MED, LOW and select.

Fan speed display turns off after approximately 10

seconds if the operation does not start.

Press the to set the Room

Temperature.

Remote control’s temperature

setting range is 16 ~ 32°C.

Room Temperature display turns

off after approximately 10

seconds if the operation does

not start.

Press the (START/STOP) button to Start the

Operation.

Operation starts with a beep.

“Operation” lamp on the indoor unit turns on.

Press the

(START/STOP) button again to stop the

operation.

From next time, the operation which has been set by

the above steps 1-3 will be available just by pressing

the START/STOP button.

One of the mode lights up.

This part lights up.

START

STOP

2

3

RAS13EX9KS2_EN_CH(1-10).p65 3/8/07, 3:40 PM9

– 10 –

AUTOMATIC OPERATION

The device will automatically determine the mode of operation COOL, or Dehumidify, depending

on the initial room temperature. The selected mode of operation will not change when the room

temperature varies. Set the current timer before start operation.

Press the FUNCTION selector so that the display

indicates the

(AUTO) mode of operation.

Press the (START/STOP) button.

Operation starts with a beep.

Press the button again to stop operation.

■ As the settings are stored in memory in the remote

controller, you only have to press the

(START/STOP)

button next time.

1

START

STOP

• The selected mode of operation will not change during the operation even though the room

temperature change.

CONDITION OF AUTOMATIC OPERATION

You can raise or lower the temperature setting as

necessary by maximum of 3°C.

Press the temperature button and the

temperature setting will change by

1°C each time.

•

“ ” is displayed when the temperature higher than

the automatically set room temperature by 1°C is set.

•

“ ” is displayed when the temperature lower than the

automatically set room temperature by 1°C is set.

To change the fan speed.

Press the

(AUTO) button.

• Select “AUTO”, “LOW” or “SILENT”.

2

INITIAL ROOM

TEMPERATURE (APPROX.)

FUNCTION

TEMPERATURE

SETTING

FAN SPEED

HIGH at start, LOW after the

preset temperature is reached.

27°CCoolOver 27°C

Dehumidfy22°C - 26°C

Same as

room temperature

LOW

RAS13EX9KS2_EN_CH(1-10).p65 3/8/07, 3:40 PM10

ENGLISH

BAHASA MELAYU

THAILAND

– 11 –

COOLING OPERATION

Press the FUNCTION selector so that the display

indicates

(COOL).

Use the device for cooling when the outdoor temperature is 21-42°C.

If humidity is very high (over 80%) indoors, some dew may form on the air outlet grille of the indoor

unit.

Set the desired FAN SPEED with the

(FAN SPEED)

button (the display indicates the setting).

(AUTO) :

The FAN SPEED is HI at first and

varies to MED automatically when

the preset temperature has been

reached.

(HI) : Economical as the room will

become cool quickly.

(MED) : Quiet.

(LOW) : More quiet.

(SILENT) : Silent.

Press

the (START/STOP) button. Cooling operation

starts with a beep. Press the button again to stop

operation. The cooling function does not start if the

temperature setting is higher than the current room

temperature (even though the

(OPERATION) lamp

lights).

The cooling function will start as soon as you set the

temperature below the current room temperature.

■ As the settings are stored in memory in the remote

controller, you only have to press the

(START/STOP)

button next time.

1

2

Set the desired room temperature with the

TEMPERATURE button (the display indicates the

setting).

The range of 25-28°C is recommended as

the room temperature for cooling. If the

temperature setting is 27°C, the room

temperature will be controlled at around

27°C.

The temperature setting and the actual room

temperature may vary somewhat depending on

conditions.

3

START

STOP

RAS13EX9KS2_EN_CH(11-24).p65 3/8/07, 3:41 PM11

– 12 –

DEHUMIDIFYING OPERATION

Use the device for dehumidifying when the room temperature is over 16°C. When it is under 15°C,

the dehumidifying function will not work.

Press the FUNCTION selector so that the display

indicates (DEHUMIDIFY).

Set the desired room temperature with

TEMPERATURE button (the display indicates the

setting).

The range of 20-26°C is recommended as the

room temperature for dehumidifying.

Press the

(START/STOP) button. Dehumidifying

operation starts with a beep. Press the button again to

stop operation.

When the room temperature is higher than the temperature setting: The device will dehumidify the

room, reducing the room temperature to the preset level. When the room temperature is lower than

the temperature setting: Dehumidifying will be performed at the temperature setting slightly lower

than the current room temperature, regardless of the temperature setting. The function will stop

(the indoor unit will stop emitting air) as soon as the room temperature becomes lower than the

setting temperature.

DEHUMIDIFYING FUNCTION

1

3

START

STOP

■

As the settings are stored in memory in the remote

controller, you only have to press the

(START/STOP)

button next time.

2

Press the button to select Low and Silent.

RAS13EX9KS2_EN_CH(11-24).p65 3/8/07, 3:41 PM12

ENGLISH

BAHASA MELAYU

THAILAND

– 13 –

Press the (START/STOP) button. Circulating

operation starts with a beep.

Press the button again to stop operation.

AIR CIRCULATION OPERATION

Press the FUNCTION selector so that the display

indicates

(CIRCULATE).

Press the (FAN SPEED) button and select the

desired FAN SPEED (the display indicates your

choice).

1

2

START

STOP

You can use the device simply as an air circulator. Use this function to dry the interior of the indoor

unit.

Press the temperature control button to set to the

desired temperature.

3

RAS13EX9KS2_EN_CH(11-24).p65 3/8/07, 3:41 PM13

– 14 –

You can use the device simply as an air circulator. Use this function to dry the interior of the indoor

unit.

Press the FUNCTION selector so that the display

indicates

(FAN).

Press the (START/STOP) button. Fan operation

starts with a beep.

Press the button again to stop operation.

FAN OPERATION

Press the (FAN SPEED) button.

1

2

START

STOP

RAS13EX9KS2_EN_CH(11-24).p65 3/8/07, 3:41 PM14

ENGLISH

BAHASA MELAYU

THAILAND

– 15 –

SUPER COOLING

Press the button.

• Operate start with a signal received sound “beep”.

• Unit will be forced operation in

(COOL) with SUPER

HI fan speed for 20 minutes.

Indicator appear during

this period while temperature and fan speed setting

display remain unchanged. (Super cooling lamp at indoor

unit is ON).

• After 20 minutes, indicator on remote controller disappear

and unit will be in

(COOL) mode. Temperature and

fan speed will change to previous setting. (Super cooling

lamp at indoor unit is OFF).

• Air blow sound will be slightly high due to forced

operation.

CANCELLATION of SUPER COOLING Operation

Cancel Condition Operation mode after cancel

Press or OFF timer time is up Stop operation

Key press

DEHUMIDIFYING operation

Press or

Press

or

Press

or

Normal COOLING operation

Press or

Press

or

20 minutes time is up

(1) OFF TIME setting : OFF timer will be a priority over the

SUPER COOLING operation time.

(2) ON TIME setting : SUPER COOLING operation will be

a priority over the ON timer operation

time.

NOTE

1

RAS13EX9KS2_EN_CH(11-24).p65 3/8/07, 3:41 PM15

– 16 –

SILENT MODE

Press the button.

• Operate start with a signal received sound “beep”.

• Unit will be forced operation in

(COOL) with SILENT fan

speed, regardless of previous setting.

CANCELLATION of SILENT Operation

Under SUPER SILENT operation and quiet environment, phenomena like flowing noise of

refrigerant in the refrigerating cycle may occur, but this is normal for the operation.

NOTE

Cancel Condition Operation mode after cancel

Press button.

OFF timer time is up Stop operation

Sleeping timer time is up.

Press

SUPER COOL button. SUPER COOL operation

Press

button. Existing operation mode

1

RAS13EX9KS2_EN_CH(11-24).p65 3/8/07, 3:41 PM16

ENGLISH

BAHASA MELAYU

THAILAND

– 17 –

EXHAUST OPERATION

Press the button.

• The device beeps when it has

received the signal and the exhaust

operation starts. By pressing the

button, the display changes as on

the right.

• The OPERATION and the "Air

Exchange Operation" lamps on the

indoor unit indicators turns on.

• Although the ventilated air is

deodorized by the Nano-Titanium

Disinfecting/Deodorizing/Dust

Collecting Fresh Air In Filter, the

odor of the ventilated air may enter

the room according to the

environment where the filter is

utilized. If there is concern regarding

any odors, please stop the device.

1

Press the (START/STOP) button.

Press the

button until Exhaust on the remote controller turns

off.

FRESH AIR IN OPERATION

Press the button.

• The device beeps when it has

received the signal and the

exhaust operation starts. By

pressing the button, the display

changes as on the right.

• The OPERATION and the "Air

Exchange Operation" lamps on the

indoor unit indicators turns on.

• Although the ventilated air is deodorized by the Nano-Titanium

Disinfecting/Deodorizing/Dust Collecting Fresh Air In Filter, the

odor of the ventilated air may enter the room according to the

environment where the filter is utilized. If there is concern

regarding any odors, please stop the device.

1

STOP

Press the (START/STOP) button.

Press the

button until Exhaust on the remote controller turns

off.

STOP

RAS13EX9KS2_EN_CH(11-24).p65 3/8/07, 3:41 PM17

– 18 –

AUTOMATIC TWO WAY EXCHANGE OPERATION

• By configuring the Automatic Two Way Air Exchange, the “Dirt Sensor” detects the dust in the

room’s air. If the air is dirty, the air conditioning automatically operates the blower and exhaust

and when the air becomes clean, the Fresh Air In is operated.

• When the prohibit Two Way Air Exchange is selected with the Two Way Air Exchange Selection

Switch (Refer page 6), please do not configure the Automatic Two Way Air Exchange. Aside

from

, the remote controller is not able to configure any other settings.

• If Fresh Air In or Exhaust is operated using the button

during Automatic Two Way Air

Exchange Set, Fresh Air In or Exhaust Operation perform in the priority.

CANCEL

• Fresh Air In operation may not perform in Automatic Two Way Air Exchange Operation when

the air inside the room is dirty.

In this case, please operate Exhaust operation manually by pressing the

(Two Way Air

Exchange) button or open the windows for ventilation.

CAUTION

Press the button.

• The device beeps when it has received the signal and

the

on the remote controller turns on.

• The “TWO WAY AIR EXCHANGE” lamp on the indoor

unit indicators turns on.

To cancel, press the

button again.

• The

on the remote controller turns off.

• The “TWO WAY AIR EXCHANGE” lamp on the indoor unit

indicators turns off.

1

RAS13EX9KS2_EN_CH(11-24).p65 03/04/2007, 01:56 pm18

ENGLISH

BAHASA MELAYU

THAILAND

– 19 –

• Press “ ” button. Remote controller sends signal,

“twin air flow” will be displayed, twin air flow with same

temperature (room air) will be blown from the fresh air

outlet by air- exchanger fan operation.

• When the air-cond operation is off, although “twin air

flow” is set in remote controller, twin air flow fan for

indoor unit will not function.

• During air-cond and air exchanger operation, select twin

air flow, air exchanger operation will be cancelled to

operate the twin air flow operation.

• Air exchanger fan’s noise level is higher than the air-

cond unit, even though the air-cond fan in “HI” fan speed.

So the noise level differential between HI, MED, LOW

speed will disappear.

• When the sleep timer is set, twin air flow operation will

be cancelled temporary.

Press the button until TWIN AIR FLOW on the remote

control turns off.

TWIN AIR FLOW OPERATION

STOP

• When using simultaneously with cooling operation, it

will direct the air flow from air-cond to upper part of

the room, to make the user feel cool.

1

Room temperature air flow

RAS13EX9KS2_EN_CH(11-24).p65 3/8/07, 3:41 PM19

– 20 –

AIR PURIFIER OPERATION

AIR EXCHANGER NOTES

Ventilation

• When the air temperature outside the room exceeds 30°C or drops below 3°C, the ventilation does

not operate to prevent dew condensation on the air exchanger fan and hose and to save energy.

• If the difference in temperature between the inside and outside of the room exceeds 7°C, the fresh

air in does not operate to prevent dew condensation on the air exchanger fan and hose, while

cooling.

• If the room humidity is more than 70%, the intake fresh air will not operate.

• When the above mentioned operations have stopped, the “Air Exchanger” lamp in the display

of the indoor unit blinks (10 seconds on / 1 second off).

Exhaust

• When the temperature inside the room exceeds 43°C, the exhaust does not operate to protect the

exhaust fan from damage.

• When the above mentioned operation has stopped, the “Air Exchanger” lamp in the display

of the indoor device blinks (10 seconds on / 1 second off).

The air purifier is operated by pressing the “ ” (AIR

PURIFIER) button.

• The device beeps when it has received the signal and

then the air purifier starts.

• The OPERATION lamp on the indoor unit indicators

turn on.

• The fan speed can be changed as desired. Either HI,

MED, LOW or SILENT can be selected.

The power of the air purifier is increased by increasing

the speed of the air conditioner’s fan, by pressing the

“

” (AIR PURIFER) button while the COOL or

DEHUMIDIFY operates.

(Depending on the operation conditions, there is a case

that the fan speed does not increase.)

Press the (START/STOP) to stop operation.

Press the “

” (AIR PURIFER) button again to

cancel the air purifier operation.

(During COOL or DEHUMIDIFY operation)

1

STOP

CANCEL

RAS13EX9KS2_EN_CH(11-24).p65 03/04/2007, 03:10 pm20

ページが読み込まれています...

Hitachi RAS-13EX9KS2 ユーザーマニュアル

このマニュアルも適しています

Hitachi RAS-13EX9KS2 ユーザーマニュアル

他の言語で

関連論文

その他のドキュメント