Supermicro SC732G-500B ユーザーマニュアル

SC732G CHASSIS SERIES

USER’S MANUAL

1.0a

SC732G-500B SC732G-900B

SUPER

®

SC732G Chassis Manual

ii

Manual Revision 1.0a

Release Date: September 18, 2013

The information in this User’s Manual has been carefully reviewed and is believed to be accurate.

The vendor assumes no responsibility for any inaccuracies that may be contained in this document,

makes no commitment to update or to keep current the information in this manual, or to notify any

person or organization of the updates. Please Note: For the most up-to-date version of this

manual, please see our web site at www.supermicro.com.

Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product

described in this manual at any time and without notice. This product, including software and

documentation, is the property of Supermicro and/or its licensors, and is supplied only under a

license. Any use or reproduction of this product is not allowed, except as expressly permitted by

the terms of said license.

IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,

SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO

USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF

SUCH DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY

HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING THE

COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH

HARDWARE, SOFTWARE, OR DATA.

Any disputes arising between manufacturer and customer shall be governed by the laws of Santa

Clara County in the State of California, USA. The State of California, County of Santa Clara shall

be the exclusive venue for the resolution of any such disputes. Super Micro's total liability for all

claims will not exceed the price paid for the hardware product.

California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate

warning applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate

Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate”

WARNING: Handling of lead solder materials used in this

product may expose you to lead, a chemical known to

the State of California to cause birth defects and other

reproductive harm.

Unless you request and receive written permission from Super Micro Computer, Inc., you may not

copy any part of this document.

Information in this document is subject to change without notice. Other products and companies

referred to herein are trademarks or registered trademarks of their respective companies or mark

holders.

Printed in the United States of America

iii

Preface

About This Manual

This manual is written for professional system integrators and PC technicians. It

provides information for the installation and use of the SC732G chassis. Installation

and maintenance should be performed by experienced technicians only.

Supermicro's mid-tower workstation /desktop platforms provide great performance

and functionality at whisper-quiet noise level, perfect for workspace or home. The

SC732G is ideal for graphics-intensive applications, extreme gaming, or video

rendering

This manual lists compatible parts available when this document was published.

Always refer to the our web site for updates on supported parts and congurations

at www.supermicro.com.

SC732G Chassis Manual

iv

Manual Organization

Chapter 1 Introduction

The rst chapter provides a description of the main components included with this

chassis and describes the main features of the SC732G chassis. This chapter also

includes contact information.

Chapter 2 Standardized Warning Statements for AC Systems

This section lists warnings, precautions, and system safety. It is recommended

that you thoroughly familiarize yourself with the chassis safety precautions before

installing and servicing this chassis.

Chapter 3 System Interface

Refer to this chapter for details on the system interface, which includes the functions

and information provided by the control panel on the chassis as well as other LEDs

located throughout the system.

Chapter 4 Chassis Setup and Maintenance

Follow the procedures given in this chapter when installing, removing, or

reconguring your chassis.

Appendix A Chassis Cables, Screws and other Accessories

Appendix B Power Supply Specications

v

Preface

Table of Contents

Chapter 1 Introduction

1-1 Overview ......................................................................................................... 1-1

1-2 Where to get Replacement Components ........................................................ 1-1

1-3 Shipping Lists .................................................................................................. 1-1

1-4 Contacting Supermicro .................................................................................... 1-3

1-5 Returning Merchandise for Service................................................................. 1-4

Chapter 2 Standardized Warning Statements for AC Systems

2-1 About Standardized Warning Statements ....................................................... 2-1

Warning Denition ........................................................................................... 2-1

Installation Instructions .................................................................................... 2-4

Circuit Breaker ................................................................................................ 2-5

Power Disconnection Warning ........................................................................ 2-6

Equipment Installation ..................................................................................... 2-8

Restricted Area ................................................................................................ 2-9

Battery Handling ............................................................................................ 2-10

Redundant Power Supplies .......................................................................... 2-12

Backplane Voltage ........................................................................................ 2-13

Comply with Local and National Electrical Codes ........................................ 2-14

Product Disposal ........................................................................................... 2-15

Hot Swap Fan Warning ................................................................................. 2-16

Power Cable and AC Adapter ...................................................................... 2-18

Chapter 3 System Interface

3-1 Overview ......................................................................................................... 3-1

3-2 Control Panel Buttons ..................................................................................... 3-3

3-3 Communication Panel Components ................................................................ 3-3

3-4 Communications Panel LEDs ......................................................................... 3-4

Chapter 4 Chassis Setup and Maintenance

4-1 Overview ......................................................................................................... 4-1

4-2 Removing the Chassis Side Covers ............................................................... 4-2

4-3 Opening/Closing the Upper and Lower Front Covers .................................... 4-3

4-4 Internal Hot-Swappable 3.5" Hard Drives ....................................................... 4-4

4-5 Hot-Swap Front 3.5" and Optional 2.5" Hard Drives ...................................... 4-7

4-6 Installing Peripheral Drives ............................................................................. 4-9

4-7 Installing the I/O Shield and Motherboard .................................................... 4-10

I/O Shield ...................................................................................................... 4-10

Motherboard Installation .................................................................................4-11

SC732G Chassis Manual

vi

4-8 Installing Expansion Cards ........................................................................... 4-12

PCI Slot Setup .............................................................................................. 4-12

Installing Expansion Cards ........................................................................... 4-13

4-9 Installing the System Fans ............................................................................ 4-14

4-10 Power Supply ............................................................................................... 4-16

Appendix A Cables, Screws, and other Accessories

Appendix B SC732G Power Supply Specications

Chapter 1

Introduction

1-1 Overview

Supermicro’s SC732G chassis features a unique and highly-optimized design, allow-

ing most conguration of the chassis to be accomplished without tools or screws.

The chassis is equipped with a high-efciency power supply and high-performance

fans provide ample optimized cooling for the system modules. Five 3.5" HDD drive

bays and four optional 2.5" HDD drive bays offer maximum storage capacity.

1-2 Where to get Replacement Components

Although not frequently, you may need replacement parts for your system. To

ensure the highest level of professional service and technical support, we strongly

recommend purchasing exclusively from our Supermicro Authorized Distributors/

System Integrators/Resellers. A list of Supermicro Authorized Distributors/System

Integrators/Reseller can be found at: http://www.supermicro.com. Click the Where

to Buy link.

1-3 Shipping Lists

Please visit the following link for the latest shipping lists and part numbers for

your particular chassis model http://www.supermicro.com/products/chassis/

tower/?chs=732

Chapter 1: Introduction

1-1

SC732G Chassis Manual

1-2

SC732G

Model Drive Front Panel I/O

Power

Supply

SC732G-900B

3x 3.5" internal HDD bays,

2x 3.5" external HDD bays,

optional 4x 2.5" HDD bays

2x USB 3.0,

2x USB 2.0

1x eSATA

2x Audio ports

900W 80

Plus Gold

Level power

supply

SC732G-500B

3x 3.5" internal HDD bays,

2x 3.5" external HDD bays,

optional 4x 2.5" HDD bays

2x USB 3.0,

2x USB 2.0

1x eSATA

2x Audio ports

500W 80

Plus Bronze

Level power

supply

1-3

Chapter 1: Introduction

1-4 Contacting Supermicro

Headquarters

Address: Super Micro Computer, Inc.

980 Rock Ave.

San Jose, CA 95131 U.S.A.

Tel: +1 (408) 503-8000

Fax: +1 (408) 503-8008

Email: [email protected] (General Information)

[email protected] (Technical Support)

Web Site: www.supermicro.com

Europe

Address: Super Micro Computer B.V.

Het Sterrenbeeld 28, 5215 ML

's-Hertogenbosch, The Netherlands

Tel: +31 (0) 73-6400390

Fax: +31 (0) 73-6416525

Email: [email protected] (General Information)

[email protected] (Technical Support)

[email protected] (Customer Support)

Asia-Pacic

Address: Super Micro Computer, Inc.

3F, No. 150, Jian 1st Rd.

Zhonghe Dist., New Taipei City 23511

Taiwan (R.O.C)

Tel: +886-(2) 8226-3990

Fax: +886-(2) 8226-3992

Web Site: www.supermicro.com.tw

Technical Support:

Email: [email protected]

Tel: +886-(2)-8226-3990

SC732G Chassis Manual

1-4

1-5 Returning Merchandise for Service

A receipt or copy of your invoice marked with the date of purchase is required be-

fore any warranty service will be rendered. You can obtain service by calling your

vendor for a Returned Merchandise Authorization (RMA) number. When returning

to the manufacturer, the RMA number should be prominently displayed on the

outside of the shipping carton, and mailed prepaid or hand-carried. Shipping and

handling charges will be applied for all orders that must be mailed when service

is complete.

For faster service, RMA authorizations may be requested online (http://www.super-

micro.com/support/rma/).

Whenever possible, repack the chassis in the original Supermicro carton, using the

original packaging material. If these are no longer available, be sure to pack the

chassis securely, using packaging material to surround the chassis so that it does

not shift within the carton and become damaged during shipping.

This warranty only covers normal consumer use and does not cover damages in-

curred in shipping or from failure due to the alteration, misuse, abuse or improper

maintenance of products.

During the warranty period, contact your distributor rst for any product problems.

2-1

Chapter 2: Warning Statements for AC Systems

Chapter 2

Standardized Warning Statements for AC Systems

2-1 About Standardized Warning Statements

The following statements are industry standard warnings, provided to warn the user

of situations which have the potential for bodily injury. Should you have questions

or experience difficulty, contact Supermicro's Technical Support department

for assistance. Only certied technicians should attempt to install or congure

components.

Read this appendix in its entirety before installing or conguring components in the

Supermicro chassis.

These warnings may also be found on our web site at http://www.supermicro.com/

about/policies/safety_information.cfm.

Warning!

This warning symbol means danger. You are in a situation that could cause bodily

injury. Before you work on any equipment, be aware of the hazards involved with

electrical circuitry and be familiar with standard practices for preventing accidents.

Warning Denition

警告の定義

この警告サインは危険を意味します。

人身事故につながる可能性がありますので、いずれの機器でも動作させる前に、

電気回路に含まれる危険性に注意して、標準的な事故防止策に精通して下さい。

此警告符号代表危险。

您正处于可能受到严重伤害的工作环境中。在您使用设备开始工作之前，必须充分

意识到触电的危险，并熟练掌握防止事故发生的标准工作程序。请根据每项警告结

尾的声明号码找到此设备的安全性警告说明的翻译文本。

此警告符號代表危險。

您正處於可能身體可能會受損傷的工作環境中。在您使用任何設備之前，請注意觸

電的危險，並且要熟悉預防事故發生的標準工作程序。請依照每一注意事項後的號

碼找到相關的翻譯說明內容。

2-2

SC116 Chassis User's Manual

Warnung

WICHTIGE SICHERHEITSHINWEISE

Dieses Warnsymbol bedeutet Gefahr. Sie benden sich in einer Situation, die zu

Verletzungen führen kann. Machen Sie sich vor der Arbeit mit Geräten mit den

Gefahren elektrischer Schaltungen und den üblichen Verfahren zur Vorbeugung

vor Unfällen vertraut. Suchen Sie mit der am Ende jeder Warnung angegebenen

Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten

Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.

BEWAHREN SIE DIESE HINWEISE GUT AUF.

INSTRUCCIONES IMPORTANTES DE SEGURIDAD

Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes

de manipular cualquier equipo, considere los riesgos de la corriente eléctrica y

familiarícese con los procedimientos estándar de prevención de accidentes. Al

nal de cada advertencia encontrará el número que le ayudará a encontrar el texto

traducido en el apartado de traducciones que acompaña a este dispositivo.

GUARDE ESTAS INSTRUCCIONES.

IMPORTANTES INFORMATIONS DE SÉCURITÉ

Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une

situation pouvant entraîner des blessures ou des dommages corporels. Avant

de travailler sur un équipement, soyez conscient des dangers liés aux circuits

électriques et familiarisez-vous avec les procédures couramment utilisées pour

éviter les accidents. Pour prendre connaissance des traductions des avertissements

gurant dans les consignes de sécurité traduites qui accompagnent cet appareil,

référez-vous au numéro de l'instruction situé à la n de chaque avertissement.

CONSERVEZ CES INFORMATIONS.

ןונקת תורהצהאהרהז

ןה תואבה תורהצהא ינפמ שמתשמה תא ריהזהל תנמ לע ,היישעתה ינקת יפ לע תורהז הלבח

ה וא תולאש שיו הדימב .תירשפא תיזיפי ,יהשלכ היעבב תולקתרוציל שי הכימת תקלחמ םע רשק

רידגהל וא ןיקתהל םיאשר דבלב םיכמסומ םיאנכט .ורקימרפוס לש תינכט תאה .םיביכר

אורקל שי .ורקימרפוס יזראמב םיביכרה תרדגה וא תנקתה ינפל ואולמב חפסנה תא

2-3

Warning Statements for AC Systems

안전을 위한 주의사항

경고!

이 경고 기호는 위험이 있음을 알려 줍니다. 작업자의 신체에 부상을 야기 할 수

있는 상태에 있게 됩니다. 모든 장비에 대한 작업을 수행하기 전에 전기회로와

관련된 위험요소들을 확인하시고 사전에 사고를 방지할 수 있도록 표준

작업절차를 준수해 주시기 바랍니다.

해당 번역문을 찾기 위해 각 경고의 마지막 부분에 제공된 경고문 번호를

참조하십시오

BELANGRIJKE VEILIGHEIDSINSTRUCTIES

Dit waarschuwings symbool betekent gevaar. U verkeert in een situatie die

lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken,

dient u zich bewust te zijn van de bij een elektrische installatie betrokken risico's

en dient u op de hoogte te zijn van de standaard procedures om ongelukken te

voorkomen. Gebruik de nummers aan het eind van elke waarschuwing om deze te

herleiden naar de desbetreffende locatie.

BEWAAR DEZE INSTRUCTIES

.   !









2-4

SC116 Chassis User's Manual

Installation Instructions

Warning!

Read the installation instructions before connecting the system to the power source.

Warnung

Vor dem Anschließen des Systems an die Stromquelle die Installationsanweisungen

lesen.

¡Advertencia!

Lea las instrucciones de instalación antes de conectar el sistema a la red de

alimentación.

Attention

Avant de brancher le système sur la source d'alimentation, consulter les directives

d'installation.

設置手順書

システムを電源に接続する前に、設置手順書をお読み下さい。



אורקל שי רוקמל תכרעמה רוביח ינפל הנקתה תוארוה תאחתמ.

시스템을 전원에 연결하기 전에 설치 안내를 읽어주십시오.

Waarschuwing

Raadpleeg de installatie-instructies voordat u het systeem op de voedingsbron

aansluit.

警告

将此系统连接电源前,请先阅读安装说明。

警告

將系統與電源連接前，請先閱讀安裝說明。

2-5

Chapter 2: Warning Statements for AC Systems

Circuit Breaker

Warning!

This product relies on the building's installation for short-circuit (overcurrent)

protection. Ensure that the protective device is rated not greater than: 250 V, 20 A.

サーキット・ブレーカー

この製品は、短絡（過電流）保護装置がある建物での設置を前提としています。

保護装置の定格が250 V、20 Aを超えないことを確認下さい。

Warnung

Dieses Produkt ist darauf angewiesen, dass im Gebäude ein Kurzschluss-

bzw. Überstromschutz installiert ist. Stellen Sie sicher, dass der Nennwert der

Schutzvorrichtung nicht mehr als: 250 V, 20 A beträgt.

¡Advertencia!

Este equipo utiliza el sistema de protección contra cortocircuitos (o sobrecorrientes)

del edicio. Asegúrese de que el dispositivo de protección no sea superior a: 250

V, 20 A.

Attention

Pour ce qui est de la protection contre les courts-circuits (surtension), ce produit

dépend de l'installation électrique du local. Vériez que le courant nominal du

dispositif de protection n'est pas supérieur à :250 V, 20 A.

לע ךמתסמ הז רצומנגהה תעינמל םינבמב תנקתומה יכ אדוול שי .ילמשח רצק

רצקה ינפמ ןגמה רישכמה ילמשחהמ רתוי אל אוה-250 V, 20 A





20A, 250V : 

警告

此产品的短路(过载电流)保护由建筑物的供电系统提供,确保短路保护设备的额定电

流不大于250V,20A。

警告

此產品的短路(過載電流)保護由建築物的供電系統提供,確保短路保護設備的額定電

流不大於250V,20A。

2-6

SC116 Chassis User's Manual

Power Disconnection Warning

電源切断の警告

システムコンポーネントの取り付けまたは取り外しのために、シャーシー内部にアクセス

するには、

システムの電源はすべてのソースから切断され、電源コードは電源モジュールから取り

外す必要があります。

警告

在你打开机箱并安装或移除内部器件前,必须将系统完全断电,并移除电源线。

警告

在您打開機殼安裝或移除內部元件前，必須將系統完全斷電，並移除電源線。

Warnung

Das System muss von allen Quellen der Energie und vom Netzanschlusskabel

getrennt sein, das von den Spg.Versorgungsteilmodulen entfernt wird, bevor es

auf den Chassisinnenraum zurückgreift, um Systemsbestandteile anzubringen oder

zu entfernen.

Warning!

The system must be disconnected from all sources of power and the power cord

removed from the power supply module(s) before accessing the chassis interior to

install or remove system components.

경고!

이 제품은 전원의 단락(과전류)방지에 대해서 전적으로 건물의 관련 설비에

의존합니다. 보호장치의 정격이 반드시 250V(볼트), 20A(암페어)를 초과하지

않도록 해야 합니다.

Waarschuwing

Dit product is afhankelijk van de kortsluitbeveiliging (overspanning) van

uw electrische installatie. Controleer of het beveiligde aparaat niet groter

gedimensioneerd is dan 220V, 20A.

2-7

Chapter 2: Warning Statements for AC Systems

¡Advertencia!

El sistema debe ser disconnected de todas las fuentes de energía y del cable

eléctrico quitado de los módulos de fuente de alimentación antes de tener acceso

el interior del chasis para instalar o para quitar componentes de sistema.

Attention

Le système doit être débranché de toutes les sources de puissance ainsi que de

son cordon d'alimentation secteur avant d'accéder à l'intérieur du chassis pour

installer ou enlever des composants de systéme.

ילמשח קותינ ינפמ הרהזא

!הרהזא

למשחה תורוקמ לכמ תכרעמה תא קתנל שי ריסהל שיו קפסהמ ילמשחה לבכ תא

נקתה ךרוצל זראמה לש ימינפה קלחל השיג ינפלת רסה ואת .םיביכר







경고!

시스템에 부품들을 장착하거나 제거하기 위해서는 섀시 내부에 접근하기 전에

반드시 전원 공급장치로부터 연결되어있는 모든 전원과 전기코드를 분리해주어야

합니다.

Waarschuwing

Voordat u toegang neemt tot het binnenwerk van de behuizing voor het installeren

of verwijderen van systeem onderdelen, dient u alle spanningsbronnen en alle

stroomkabels aangesloten op de voeding(en) van de behuizing te verwijderen

2-8

SC116 Chassis User's Manual

Equipment Installation

機器の設置

トレーニングを受け認定された人だけがこの装置の設置、交換、またはサービスを許可

されています。

Warning!

Only trained and qualied personnel should be allowed to install, replace, or service

this equipment.

Warnung

Das Installieren, Ersetzen oder Bedienen dieser Ausrüstung sollte nur geschultem,

qualiziertem Personal gestattet werden.

¡Advertencia!

Solamente el personal calicado debe instalar, reemplazar o utilizar este equipo.

Attention

Il est vivement recommandé de confier l'installation, le remplacement et la

maintenance de ces équipements à des personnels qualiés et expérimentés.

!הרהזא

שר דבלב ךמסומ תווצתא ףילחהל ,ןיקתהל יא .דויצה רובע תוריש תתל וא דויצה

 

경고!

훈련을 받고 공인된 기술자만이 이 장비의 설치, 교체 또는 서비스를 수행할 수

있습니다.

警告

只有经过培训且具有资格的人员才能进行此设备的安装、更换和维修。

警告

只有經過受訓且具資格人員才可安裝、更換與維修此設備。

2-9

Chapter 2: Warning Statements for AC Systems

アクセス制限区域

このユニットは、アクセス制限区域に設置されることを想定しています。

アクセス制限区域は、特別なツール、鍵と錠前、その他のセキュリティの手段を用いての

み出入りが可能です。

Warning!

This unit is intended for installation in restricted access areas. A restricted access

area can be accessed only through the use of a special tool, lock and key, or other

means of security. (This warning does not apply to workstations).

Restricted Area

Waarschuwing

Deze apparatuur mag alleen worden geïnstalleerd, vervangen of hersteld door

geschoold en gekwaliceerd personeel.

Warnung

Diese Einheit ist zur Installation in Bereichen mit beschränktem Zutritt vorgesehen.

Der Zutritt zu derartigen Bereichen ist nur mit einem Spezialwerkzeug, Schloss und

Schlüssel oder einer sonstigen Sicherheitsvorkehrung möglich.

¡Advertencia!

Esta unidad ha sido diseñada para instalación en áreas de acceso restringido.

Sólo puede obtenerse acceso a una de estas áreas mediante la utilización de una

herramienta especial, cerradura con llave u otro medio de seguridad.

Attention

Cet appareil doit être installée dans des zones d'accès réservés. L'accès à une

zone d'accès réservé n'est possible qu'en utilisant un outil spécial, un mécanisme

de verrouillage et une clé, ou tout autre moyen de sécurité.

警告

此部件应安装在限制进出的场所，限制进出的场所指只能通过使用特殊工具、锁和

钥匙或其它安全手段进出的场所。

警告

此裝置僅限安裝於進出管制區域，進出管制區域係指僅能以特殊工具、鎖頭及鑰匙

或其他安全方式才能進入的區域。

2-10

SC116 Chassis User's Manual

Battery Handling

Warning!

There is the danger of explosion if the battery is replaced incorrectly. Replace the

battery only with the same or equivalent type recommended by the manufacturer.

Dispose of used batteries according to the manufacturer's instructions

תלבגומ השיג םע רוזא

!הרהזא

תרזעב תנתינ השיגה .השיג תלבגה םהב שיש םירוזאב הדיחיה תא ןיקתהל שי

.)'דכו לוענמ ,חתפמ( דבלב החטבא ילכ

.  



 

경고!

이 장치는 접근이 제한된 구역에 설치하도록 되어있습니다. 특수도구, 잠금 장치 및

키, 또는 기타 보안 수단을 통해서만 접근 제한 구역에 들어갈 수 있습니다.

Waarschuwing

Dit apparaat is bedoeld voor installatie in gebieden met een beperkte toegang.

Toegang tot dergelijke gebieden kunnen alleen verkregen worden door gebruik te

maken van speciaal gereedschap, slot en sleutel of andere veiligheidsmaatregelen.

電池の取り扱い

電池交換が正しく行われなかった場合、破裂の危険性があります。交換する電池はメー

カーが推奨する型、または同等のものを使用下さい。使用済電池は製造元の指示に従

って処分して下さい。

警告

电池更换不当会有爆炸危险。请只使用同类电池或制造商推荐的功能相当的电池更

换原有电池。请按制造商的说明处理废旧电池。

警告

電池更換不當會有爆炸危險。請使用製造商建議之相同或功能相當的電池更換原有

電池。請按照製造商的說明指示處理廢棄舊電池。

ページが読み込まれています...

Supermicro SC732G-500B ユーザーマニュアル

このマニュアルも適しています

Supermicro SC732G-500B ユーザーマニュアル

他の言語で

関連論文

その他のドキュメント