HP f800g Car Camcorder Getting Started

1

Battery warning

 The battery for this car camcorder is sealed internally. DO NOT

attempt to disassemble the camcorder and remove the battery.

 Always charge using the provided system. Improper charging of the

battery may result in explosion.

 The battery is designed for this camcorder and is not customer

replaceable.

 Batteries may explode if exposed to naked fire. Never expose the

car camcorder in a fire.

 Recycle the camcorder observing local regulations.

Notes on Installation

1. Install the device near the rear-view mirror to obtain the best

open-field view. Do NOT install the camcorder in a location that will

obstruct your required driving view.

2. Make sure that the lens is within the wiping range of the

windscreen wiper to ensure a clear view even when it rains.

3. Do not touch the lens with your fingers. Finger grease may be left

on the lens and will result in unclear videos or snapshots. Clean the

lens on a regular basis.

4. Do not install the device on a tinted window. Doing so may damage

the tint film.

5. Make sure that the installation position is not hindered by the

tinted window.

2

1 Introduction

1.1 Package Contents

The package contains the following items. In case there is any missing or

damaged item, contact your dealer immediately.

Camcorder Bracket

CD-ROM Quick start guide Car adapter

3

1.2 Product Overview

No. Item No. Item

1 Bracket Socket 6 GPS Antenna

2 Memory Card Slot 7 Wide Angle Lens

3 Power Switch 8 Speaker

4 LED Indicator 9 Microphone

5 USB / Power Connector 10 LCD Touch Panel

Top and Bottom Views

Side (Left and Right) Views

Front View

Rear View

2

8

9

1

10

4

5

7

6

3

4

2 Getting Started

2.1 Inserting the Memory Card

Insert memory card with the gold section facing upward and the screen

of the camcorder facing upward too, as illustrated. Push the memory

card in until a click sound is heard, indicating the card is in position.

To remove the memory card

Push to eject the memory card out of the slot.

Note:

1. Do not remove or insert the memory card when the camcorder is turned on. This

may damage the memory card.

2. Please use a Class 6 or higher rating Micro SD card, max. up to 32GB.

3. Please format the micro SD cards before the initial use.

4. When removing the memory card, be careful that the card may spring out and get

lost. The memory slot has this spring-out feature for easy removal of the card.

5

2.2 Installing in Vehicles

2.2.1 Mount to Windshield

1. Push the bracket into bracket slot on top of

camcorder, until a click sound is heard.

2. With the suction-cup laying flat,

position the suction-cup on the

windshield.

3. Hold the base firmly on the windshield

and press down the clamp to mount the

car holder to the windshield. Make sure

the base is securely locked in place.

6

2.2.2 Adjust the Camcorder position

1. Loose the knob to swivel the

camcorder vertically.

2. Loose the knob to swivel the

camcorder horizontally up to

360°.

3. Then tighten the knob to make sure the camcorder is securely

locked in place.

Knob

7

2.3 Connecting to Power

Use only the supplied car adapter to power up the camcorder and

charging the built-in battery.

1. Connect one end of car adapter to USB/Power connector port on the

camcorder.

2. Plug the other end of the car adapter to the cigarette lighter socket

of your vehicle. Once the vehicle engine is started, the camcorder

automatically powers on.

Note:

This product shall be installed near the rear mirror, at the center of windshield, if

possible, for optimal viewing.

8

2.4 Powering the Camcorder On / Off

2.4.1 Auto Power On/Off

Once the vehicle engine is started, the camcorder automatically turns on.

If the Automatic Record function is enabled, the recording will

automatically start right after the camcorder powers on.

2.4.2 Manual Power On/Off and Reset

2.4.2.1 Manual Power On

Slide the power switch and make sure that the power switch locks on the

memory card slot.

On

2.4.2.2 Power Off

The power switch to the edge and make sure that the memory slot is

released and the camcorder starts power off sequence. Do not power on

the camcorder when it is in the power-off sequence, or the recorded file

may become corrupt.

O

ff

9

2.5 Initial Settings

Before using the camcorder, we recommend you to enable the

Automatic Record function and set up the correct Date and Time.

2.5.1 Setting the Universal Time Code (UTC)

Depending on your location, you may need to change the current UTC

setting of the camcorder so that the correct date and time are updated

when a GPS signal is detected.

* Be sure to adjust for daylight saving time (DST) by adding +1 hour to the UTC offset.

** These areas may observe half hour increments and daylight saving time (DST).

10

3 Using the Car Recorder

3.1 Recording Videos

3.1.1 LDWS (Lane Departure Warning Systems)

When LDWS is enabled after satellite positioning, camcorder will give a

voice alert and display an alarm screen if vehicle speed reaches or

exceeds 50 km/h (31 mile/h) and the vehicle deviates from the original

lane.

To set the LDWS (Lane Departure Warning Systems), do the following:

1. Ensure the camcorder is

connected to the power adapter

and is receiving power.

2. Touch to enter Main

Menu.

3. Touch to switchover to

Driving Safety Main Menu.

4. Touch / to select

for entering LDWS function menu,

then touch again to

enable the function (on).

5. Touch to return to record screen.

6. After enabling LDWS, the screen will display align icon ,

please adjust the camcorder so that the horizontal line and the eye

level are overlapped and the slash lines are centered in the driving

lane. Make sure that align icon will not be obscured (e.g. hood)

during installation, it may cause misjudgment if the endpoint is

obscured.

11

Eye Level

Horizon

Vanishing Point

7. When satellite positioning is in ready state, camcorder will give a

voice alert and an alarm screen if vehicle speed reaches or exceeds

50 km/h (31 mile/h) and the vehicle deviates from the original lane.

Note:

1. LDWS is only applicable when satellite positioning is in ready state. Make sure

satellite positioning of your camcorder is ready if you want to activate this function.

Satellite positioning function is dependent on the model purchased.

2. When enable the LDWS, please follow this self-aligned approach in order to increase

the accuracy.

3. The all Driving Safety functions such as LDWS, Speed Cam Alert, Speed Limit Alert,

Driver Fatigue Alert and Collision Detection will be disabled, if the product doesn’t

connect with the external power supply.

12

3.1.2 Motion Detection

If Motion Detection is activated, when the camcorder is powered on, a

message “Wait for 10 seconds to enter Motion Detection or touch the

screen to power off” will be displayed on the screen. This means the

system will enter Motion Detection automatically in 10 seconds; when

the camcorder detects any motion in front of lens, Video Record will be

activated for a duration the same as the length setting.

To set the motion detection, do the following:

1. Touch to enter main

menu.

2. Touch to switch over

to Driving Safety Main Menu.

3. Touch / to select

for entering Motion

Detection menu, touch

again to activate (on).

4. Touch to return to record screen.

Note:

1. When the battery is fully charged and is in good condition, Motion Detection can

record continuously for about 30 minutes.

2. As the camcorder is used, the battery storage capacity will decrease gradually. This

is a normal phenomenon for the battery.

13

3.1.3 Emergency Recording

Start the Emergency Recording, do the following:

1. During video recording, touch

to enter emergency

recording mode, the “Emergency”

message will be shown

immediately on the lower left

corner of the screen, and the

recorded file will be protected.

2. Touch again, to halt the recording.

Note:

1. If the Collision Detection function is enabled and a collision is detected, the

camcorder will automatically trigger the emergency recording.

2. The emergency recording file is created as a new file, which will be protected to

avoid being overwritten by normal looping recording. 8G (or above) memory card

can save up to 8 emergency video files. The alert message of “Emergency files are

full” will pop up on the screen when the emergency recording files are full, and the

oldest emergency file will be automatically deleted when a new emergency

recording file is created.

14

3.2 Playing Videos and Viewing Pictures

3.2.1 Playing Videos and Emergency Recording

Playback video record files as follows:

1. Touch to enter main menu.

2. Touch to switch over to File / Position menu.

3. Touch / to enter Video/

Emergency function menu.

4. Touch / to browse for

required video file, touch selected preview of video to enter

Playback Mode

5. Touch repetitively to return to Record Screen.

15

3.2.2 Viewing Pictures

View pictures as follows:

1. Touch to enter Main Menu.

2. Touch to switch over to File / Position main menu.

3. Touch to enter Picture

function menu.

4. Touch / to browse for required picture files, touch

selected preview of picture to enter Picture Playback Mode.

5. Touch repetitively to return Record Screen.

16

3.2.3 Deleting Files

To delete file(s), do the following:

1. Touch to enter Main Menu.

2. Touch to switch over to File / Position main menu.

3. Touch / / to enter Video/Picture/Emergency menu.

4. Touch / to browse for required video or picture file; touch

selected preview image to enter Video/Picture Playback Mode.

5. Touch to enter File Deletion menu, select / to

delete one file or all files; touch / to confirm or cancel

the selection.

Item Description

Delete One Delete the current file.

Delete All Delete all files.

6. Touch repetitively to return to Record Screen.

Note:

Deleted files cannot be recovered. Ensure the files have backup before deletion.

1

電池

電池電池

電池注意事項

注意事項注意事項

注意事項

 僅可使用本系統充電，未正確處理電池可能會引發爆炸。

 請勿自行拆裝、穿刺電池，或使電池短路。

 電池接觸明火可能會引起爆炸，請勿將電池丟棄到火中。

 請根據當地法規妥善處理使用過的電池。

 此電池為內置

此電池為內置此電池為內置

此電池為內置嚴禁自行更換電池

嚴禁自行更換電池嚴禁自行更換電池

嚴禁自行更換電池，

，，

，欲更換電池請洽經銷商

欲更換電池請洽經銷商欲更換電池請洽經銷商

欲更換電池請洽經銷商。

。。

。

安裝須知

安裝須知安裝須知

安裝須知

1. 本產品之安裝應靠近後視鏡，以獲得最佳的視野。

2. 確定鏡頭是在擋風玻璃雨刷的範圍內，確保視野良好，即使雨

天亦然。

3. 不要用手指碰觸鏡頭。手指上的油垢可能會留在鏡頭上，導致

錄像或攝影不清楚。定期清潔鏡頭。

4. 不要將產品安裝在有色車窗上。因為這樣會損壞淺色薄膜。

5. 確定安裝位置不會受有色車窗的阻礙。

2

1 導論

導論導論

導論

1.1 包裝

包裝包裝

包裝內容

內容內容

內容

以下為包裝內容物。若有任何遺漏或損壞項目，請立即聯絡您的經銷

商，外觀請依內容物實際狀況為主。

行車記錄器托架

光碟

快速使用手冊電源連接器

3

1.2 產品概要

產品概要產品概要

產品概要

編號

編號編號

編號

項目

項目項目

項目

編號

編號編號

編號項目

項目項目

項目

1

托架插孔

6

衛星定位天線

2

記憶卡插槽

7

廣角鏡

3

電源開關

8

揚聲器

4

LED 指示燈

9

麥克風

5

USB / 電源連接孔

10

LCD 觸控螢幕

頂視圖與底視圖

側視圖 (左側與右側)

前視圖

後視圖

2

8

9

3

10

4

5

7

6

1

ページが読み込まれています...

HP f800g Car Camcorder Getting Started

このマニュアルも適しています

HP f800g Car Camcorder Getting Started

他の言語で

関連論文

その他のドキュメント