Tascam 102i Series 取扱説明書

ENGLISH

FRANÇAIS

ESPAÑOL

DEUTSCH

ITALIANO

日本語

OWNER'S MANUAL

MODE D’EMPLOI

MANUAL DEL USUARIO

BEDIENUNGSANLEITUNG

MANUALE DI ISTRUZIONI

取扱説明書

D01355400B

SERIES 102i

SERIES 208i

AUDIO INTERFACE

2

TASCAM SERIES 102i / SERIES 208i

TEAC CORPORATION

https://tascam.jp/jp/

Phone: +81-42-356-9143

1-47 Ochiai, Tama-shi, Tokyo 206-8530 Japan

TEAC AMERICA, INC.

https://tascam.com/us/

Phone: +1-323-726-0303

10410 Pioneer Blvd. Suite #1 Santa Fe Springs, California

90670, U.S.A.

TEAC UK Ltd.

https://www.tascam.eu/en/

Phone: +44-1923-797205

Meridien House, 69-71 Clarendon Road, Watford, Herts,

WD17 1DS, United Kingdom

TEAC EUROPE GmbH

https://www.tascam.en/de/

Phone: +49-611-71580

Bahnstrasse 12, 65205 Wiesbaden-Erbenheim, Germany

TEAC SALES & TRADING(SHENZHEN) CO., LTD

https://tascam.cn/cn/

Phone: +86-755-88311561~2

Room 817, Xinian Center A, Tairan Nine Road West, Shen-

nan Road, Futian District, Shenzhen, Guangdong Province

518040, China

• TASCAM is a registered trademark of TEAC Corporation.

• Microsoft, Windows and Windows Vista are either registered

trademarks or trademarks of Microsoft Corporation in the

United States and/or other countries.

• Apple, Mac, Mac OS X, and Lightning are trademarks of

Apple Inc.

• IOS is a trademark or registered trademark of Cisco in the

U.S. and other countries and is used under license.

• ASIO is a trademark and software of Steinberg Media

Technologies GmbH.

• Other company names, product names and logos in this

document are the trademarks or registered trademarks

of their respective owners.

TASCAM SERIES 102i / SERIES 208i

3

IMPORTANT SAFETY INSTRUCTIONS

WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT

EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

For U.S.A.

Declaration of Conformity

Model Number: SERIES 102i / SERIES 208i

Trade Name: TASCAM

Responsible party: TEAC AMERICA, INC.

Address: 10410 Pioneer Blvd. Suite #1 Santa Fe Springs,

California 90670, U.S.A.

Telephone number: 1-323-726-0303

This device complies with Part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) this device may not

cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause

undesired operation.

INFORMATION TO THE USER

This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential instal-

lation. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance

with the instruction manual, may cause harmful interference

to radio communications. However, there is no guarantee that

interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures.

a) Reorient or relocate the receiving antenna.

b) Increase the separation between the equipment and

receiver.

c) Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

d) Consult the dealer or an experienced radio/TV technician for

help.

CAUTION

Changes or modifications to this equipment not expressly

approved by TEAC CORPORATION for compliance could void

the user’s authority to operate this equipment.

For Canada

THIS CLASS B DIGITAL APPARATUS COMPLIES WITH CANADIAN

ICES-003.

CET APPAREIL NUMERIQUE DE LA CLASSE B EST CONFORME A

LA NORME NMB-003 DU CANADA.

This product complies with the European

Directives request and the other Commission

Regulations.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance

with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat

registers, stoves, or other apparatus (including amplifiers)

that produce heat.

9. Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades with

one wider than the other. A grounding type plug has two

blades and a third grounding prong. The wide blade or the

third prong are provided for your safety. If the provided

plug does not fit into your outlet, consult an electrician for

replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the point

where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufac-

turer.

12. Use only with the cart, stand, tripod, bracket, or table

specified by the manufacturer, or sold with the apparatus.

When a cart is used, use caution when moving the cart/

apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when

unused for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is

required when the apparatus has been damaged in any way,

such as power-supply cord or plug is damaged, liquid has

been spilled or objects have fallen into the apparatus, the

apparatus has been exposed to rain or moisture, does not

operate normally, or has been dropped.

• The apparatus draws nominal non-operating power from the

AC outlet with its POWER or STANDBY/ON switch not in the ON

position.

• The mains plug is used as the disconnect device, the

disconnect device shall remain readily operable.

• Caution should be taken when using earphones or

headphones with the product because excessive sound

pressure (volume) from earphones or headphones can cause

hearing loss.

• If you are experiencing problems with this product, contact

TEAC for a service referral. Do not use the product until it has

been repaired.

OWNER’S MANUAL

4

TASCAM SERIES 102i / SERIES 208i

CAUTION

• Do not expose this apparatus to drips or splashes.

• Do not place any objects filled with liquids, such as vases, on

the apparatus.

• Do not install this apparatus in a confined space such as a

book case or similar unit.

• The apparatus should be located close enough to the AC

outlet so that you can easily grasp the power cord plug at

any time.

• If the product uses batteries (including a battery pack or

installed batteries), they should not be exposed to sunshine,

fire or excessive heat.

• CAUTION for products that use replaceable lithium batteries:

there is danger of explosion if a battery is replaced with

an incorrect type of battery. Replace only with the same or

equivalent type.

For European Customers

Disposal of electrical and electronic equipment

(a) All electrical and electronic equipment should be disposed

of separately from the municipal waste stream via collection

facilities designated by the government or local authorities.

(b) By disposing of electrical and electronic equipment

correctly, you will help save valuable resources and prevent

any potential negative effects on human health and the

environment.

(c) Improper disposal of waste electrical and electronic

equipment can have serious effects on the environment

and human health because of the presence of hazardous

substances in the equipment.

(d) The Waste Electrical and Electronic Equipment

(WEEE) symbol, which shows a wheeled bin that

has been crossed out, indicates that electrical

and electronic equipment must be collected and

disposed of separately from household waste.

(e) Return and collection systems are available to end users.

For more detailed information about the disposal of old

electrical and electronic equipment, please contact your

city office, waste disposal service or the shop where you

purchased the equipment.

CAUTION

• DO NOT REMOVE THE EXTERNAL CASES OR CABINETS TO

EXPOSE THE ELECTRONICS. NO USER SERVICEABLE PARTS ARE

INSIDE.

• IF YOU ARE EXPERIENCING PROBLEMS WITH THIS PRODUCT,

CONTACT THE STORE WHERE YOU PURCHASED THE UNIT FOR

A SERVICE REFERRAL. DO NOT USE THE PRODUCT UNTIL IT HAS

BEEN REPAIRED.

• USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF

PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY

RESULT IN HAZARDOUS RADIATION EXPOSURE

The nameplate is located on the bottom of the unit as shown

below.

SERIES 102i

Front side

SERIES 208i

Front side

Nameplate

TASCAM SERIES 102i / SERIES 208i

5

Introduction

Thank you very much for purchasing a TASCAM SERIES 102i/SERIES

208i audio interface.

Before connecting and using this unit, please take time to read

this manual thoroughly to ensure you understand how to properly

set it up and connect it, as well as how to use its many useful and

convenient functions. After you have finished reading this manual,

please keep it in a safe place for future reference.

You can also download this Owner’s Manual from the TEAC Global

Site (http://teac-global.com/).

Before connecting this unit to a computer, you must download

and install a dedicated driver.

Note about the Reference Manual

This Owner’s Manual explains each of the functions of this unit.

Please see the Reference Manual for detailed information about

each of the functions.

You can download the Reference Manual from the TEAC Global

Site (http://teac-global.com/).

Included items

This product includes the following items.

Take care when opening the package to avoid damaging the

items. Keep the box and packing materials for transportation in

the future.

Please contact the store where you purchased this unit if any of

these items are missing or have been damaged during transpor-

tation.

0 Main unit ...................................................................................................× 1

0 AC adapter (PS-P1220E) (with 3 alternate plugs) ....................... × 1

0 USB cable ..................................................................................................× 1

0 Set of DAW software installation guides .......................................× 1

0 Set of DAW plug-in software installation guides .......................× 1

0 Owner’s Manual (this document) including warranty .............× 1

ATTENTION

Always use the included AC adapter (PS-P1220E) when using

this unit. Never use the included AC adapter with any other de-

vice. Doing so could cause damage, fire or electric shock.

NOTE

The included AC adapter (PS-P1220E) is shipped with alternate

outlet plugs. Please see “Changing the outlet plug” on page

10.

Conventions used in this manual

In this manual, we use the following conventions:

0 Buttons, connectors and other physical parts of this unit and

connected devices are written using a bold font like this:

PHONES knob.

0 Information shown on a computer display is written like this:

“OK”.

0 As necessary, additional information is provided under TIP,

NOTE and CAUTION headings.

TIP

These are tips about how to use the unit.

NOTE

These provide additional explanations and describe spe cial

cases.

Contents

IMPORTANT SAFETY INSTRUCTIONS ........................................ 3

Introduction ................................................................................ 5

Note about the Reference Manual ............................................ 5

Included items ............................................................................ 5

Conventions used in this manual .............................................. 5

Precautions for placement and use ........................................... 6

Beware of condensation ............................................................ 6

Cleaning the unit ........................................................................ 6

Using the TEAC Global Site ........................................................ 6

Product registration ................................................................... 6

About TASCAM customer support service ................................ 6

Names and functions of parts ................................................... 6

Front panel ....................................................................................................6

Rear panel ......................................................................................................7

Installing the dedicated software ............................................. 8

Installing the Windows dedicated software ...................................... 8

Installing the Mac dedicated software ................................................ 9

Connecting the power .............................................................. 10

Changing the outlet plug ...................................................................... 10

Connecting other equipment .................................................. 11

Connecting with iOS devices ................................................... 11

Adjusting the input sound ....................................................... 11

Making various settings ........................................................... 12

Opening the Settings Panel ................................................................. 12

Settings Panel overview ........................................................................ 12

Making settings on the MIXER screen .............................................. 12

Making settings on the INFORMATION screen .............................. 12

Making settings on the ROUTING screen ........................................ 13

Changing sampling frequency ................................................ 13

Troubleshooting ....................................................................... 13

Specifications ............................................................................ 14

Ratings ......................................................................................................... 14

Analog audio input ratings ................................................................... 14

Analog outputs ......................................................................................... 15

Digital audio input ratings .................................................................... 15

Control input/output .............................................................................. 15

Audio performance ................................................................................. 15

Computer system requirements .............................................. 16

Windows ...................................................................................................... 16

Mac ................................................................................................................ 16

iOS device ................................................................................................... 16

Supported audio drivers ........................................................................ 16

General ...................................................................................... 16

Dimensional drawings ............................................................. 16

6

TASCAM SERIES 102i / SERIES 208i

ATTENTION

Failure to follow these instructions could result in damage to

equipment or lost data, for example.

V

CAUTION

Failure to follow these instructions could result in injury.

Precautions for placement and use

0 The operating temperature range of this unit is 5–35 °C.

0 Do not install this unit in the following types of locations.

Doing so could make the sound quality worse or cause malfunc-

tion.

Places with significant vibrations

Next to a window or in another location exposed to direct

sunlight

Near heaters or other extremely hot places

Extremely cold places

Very humid or poorly ventilated places

Very dusty places

0 To enable good heat dissipation, do not place anything on top

of the unit.

0 Do not place this unit on top of a power amplifier or other de-

vice that generates heat.

Beware of condensation

Condensation could occur if the unit is moved from a cold place

to a warm place, it is used immediately after a cold room has

been heated or it is otherwise exposed to a sudden temperature

change.To prevent this, or if this occurs, let the unit sit for one or

two hours at the new room temperature before using it.

Cleaning the unit

Use a dry soft cloth to wipe the unit clean. Do not wipe with chem-

ical cleaning cloths, thinner, alcohol or other chemical agents. Do-

ing so could damage the surface or cause discoloration.

Using the TEAC Global Site

You can download updates for this unit from the TEAC Global Site:

http://teac-global.com/

In the TASCAM Downloads section, select the desired language to

open the Downloads website page for that language.

Product registration

Customers in the USA, please visit the following TASCAM website

to register your TASCAM product online.

https://tascam.com/us/

About TASCAM customer support

service

TASCAM products are supported and warrantied only in their

country/region of purchase.

To receive support after purchase, on the TASCAM Distributors list

page of the TEAC Global Site (http:// teac-global.com/), search for

the local company or representative for the region where you pur-

chased the product and contact that organization.

When making inquiries, the address (URL) of the shop or web shop

where it was purchased and the purchase date are required.

Moreover, the warranty card and proof of purchase might also be

necessary.

Names and functions of parts

Front panel

SERIES 102i

SERIES 208i

1 SIG indicators

These light green when signals (of at least -32 dBFS) are input.

2 GAIN knobs

Use to adjust the input levels of the input jacks.

3 PEAK indicators

These light red when signals are about to distort (-1 dBFS or

higher).

Adjust these so that the PEAK indicators do not light red.

4 USB indicator

This indicator shows the status of the unit by lighting, blinking

and turning off.

Status Meaning

Lit Good USB connection

Blinking

Bad USB connection

(disconnected or error occurred)

Unlit Operating in standalone mode

5 indicator

This indicator lights when the STANDBY switch is set to on.

This indicator blinks if the clock source or OPTICAL input is ir-

regular (when the clock source is set to WORD or OPTICAL).

6 MONITOR BALANCE knob

Use this to adjust the balance between the signals from this

unit’s input jacks and the output signals from the computer.

The volume of signals input through this unit’s input jacks in-

crease the more the MONITOR BALANCE knob is set to the left

(INPUT) and signals output from the computer increase the

more this is set to the right (COMPUTER).

This knob does not affect the recording level of input signals.

Input monitoring without lag is possible by monitoring the sig-

nals from the input jacks (direct monitoring).

TASCAM SERIES 102i / SERIES 208i

7

7 PHONES knob

Use to adjust the output levels of the PHONES and jacks.

V

CAUTION

Before connecting headphones, minimize the volume with the

PHONES knob. Failure to do so could result in a sudden loud

noise that could harm hearing, for example.

8 1-2 input jacks

These analog inputs are XLR/TRS combo jacks.

They can support high impedance input, including direct gui-

tar input.

Use the input switches on the front of the unit to select bal-

anced line (MIC/LINE) or unbalanced (INST) input for the TRS

jacks.

When directly connecting a guitar, bass or other instrument,

set the input switch to INST.

9 Input switches

Set according to the input source of each input jack.

INST: Select when connecting a guitar, bass or other high-im-

pedance instrument. This makes it an unbalanced input

for high impedance.

MIC/LINE: Select when connecting a balanced-output mic or

line-level-output device.

+48V: This provides +48V phantom power to the 1-2 (and 3-4

on SERIES 208i) XLR input connectors.

0 +48V indicators

These indicators light when their input switches are set to

+48V.

q 3-4 input jacks (SERIES 208i only)

These analog inputs are XLR/TRS combo jacks.

They also support high impedance input, including direct gui-

tar input.

Use the input switches on the front of the unit to select bal-

anced line (MIC/LINE) or unbalanced (INST) input for the TRS

jacks.

When directly connecting a guitar, bass or other instrument,

set the input switch to INST.

w MONITOR knob

Use to adjust the output level of the LINE OUT (BALANCED)

1-2 jacks on the back of the unit.

e PHONES / jacks

Use this standard stereo jack to connect stereo headphones.

These output the same signals as the LINE OUT (BALANCED)

1-2 jacks on the back of the unit.

Use an adapter to connect headphones with a mini plug.

NOTE

The same signals are output from both the PHONES and

PHONES jacks.

Rear panel

SERIES 102i

SERIES 208i

r Kensington Security Slot

t WORD IN/OUT connectors (SERIES 208i only)

These BNC connectors are for the input and output of word

clock signals.

Word clock signals of 44.1, 48, 88.2, 96, 176.4 and 192 kHz can

be input and output.

ATTENTION

If a digital system has multiple word clock masters, serious

problems, including damage to equipment, could occur.

y 75Ω ON/OFF switch (SERIES 208i only)

When this switch is set to ON, the WORD IN connector termi-

nates to 75 Ω.

u STANDBY switch

Press to turn the unit on and to put it into standby.

i Cord holder

Hook the cord of the included PS-P1220E AC adapter here to

prevent accidental disconnection.

o LINE OUT (BALANCED) 3-8 jacks (SERIES 208i only)

These standard TRS jacks are analog line outputs.

The nominal output level is +4 dBu.

(Tip: HOT, Ring: COLD, Sleeve: GND)

p LINE OUT (BALANCED) 1-2 jacks

These standard TRS jacks are analog line outputs.

The nominal output level is +4 dBu.

(Tip: HOT, Ring: COLD, Sleeve: GND)

a MIDI OUT connector

This 5-pin DIN is a standard MIDI output connector.

This outputs MIDI signals.

s MIDI IN connector

This 5-pin DIN is a standard MIDI input connector.

Use this to input MIDI signals.

d OPTICAL IN (S/MUX) connector(s)

These input multichannel digital audio in optical format.

44.1, 48, 88.2, 96, 176.4 and 192 kHz sampling frequencies are

supported.

88.2/96 kHz is supported by S/MUX2, and 176.4/192 kHz is

supported by S/MUX4.

8

TASCAM SERIES 102i / SERIES 208i

f USB port

Use the included USB cable to connect the unit to a computer.

(Supports USB 2.0.)

ATTENTION

i

When connected to a port that supports USB 3.0 or later, it will

function in High Speed mode equivalent to USB 2.0 (480Mbps

maximum).

i

After waking a computer from suspend (sleep) mode, if the unit

does not operate properly, turn it off and turn it on again or dis-

connect and reconnect the USB cable.

g DC IN 12V connector

Connect the included AC adapter (PS-P1220E) here.

Installing the dedicated software

To use this unit, a dedicated software must be installed on a com-

puter. The dedicated software might be updated at any time.

Download the latest software for the operating system you are

using from the TEAC Global Site (http://teac-global.com/).

0 When you install the dedicated software on a Windows com-

puter, the Windows driver and the Settings Panel application

will be installed.

0 When you install the dedicated software on a Mac, only the

Mac Settings Panel application will be installed.

The standard OS driver will be used.

0 With an iOS device, the standard OS driver will be used, so

there is no need to install any.

ATTENTION

Before starting to install software, quit other applications.

Installing the Windows dedicated soft-

ware

ATTENTION

i

Complete installation of the Windows dedicated software on

the computer before connecting the unit to it with the USB ca-

ble.

i

If you connected the unit to the computer using the USB ca-

ble before installing the Windows dedicated software and the

“Found New Hardware Wizard” launched, close the Wizard and

disconnect the USB cable.

Windows dedicated software installation

procedures

1. Download the latest Windows dedicated software for the

operating system you are using from the TEAC Global Site

(http://teac-global.com/) and save it on the computer to be

used with the unit.

2. Open the saved Windows software (zip file) on, for example,

the computer desktop.

3. Double-click the “TASCAM_SERIES_102i_208i_Installer_x.xx-

.exe” (x.xx is the version number) file in the folder that appears

after uncompression to automatically launch the installation

software.

ATTENTION

If you open a zip file without decompressing it and doubleclick

the “TASCAM_SERIES_102i_208i_Installer_x. xx.exe” file in the

folder that opens, installation will not start. Right-click the zip

file and select “Extract All”, for example, to decompress it and

then try again.

4. Depending on the computer set up, a “Security Warning” or

“User Account Control” screens might appear. If this occurs,

click the “Yes” button.

5. Read the contents of the License Agreement, and select “I ac-

cept the agreement” if you agree to the terms.

Then, click the “Next >” button.

6. Next, click the “Install” button.

7. When the Windows security screen appears, click the “Install”

button to start installation.

8. The following screen appears when installation has complet-

ed.

Click the “Finish” button.

The installer will quit and the Windows Settings Panel will

launch.

NOTE

The first time you connect the unit by USB to the computer af-

ter installing the software, installation of the device driver will

be executed. Some time might be necessary before the unit

is recognized because Windows Update will be automatically

searched at this time.

If the unit is still not recognized after a while, open the software

installation screen from the notification area at the bottom right

of the computer display, and click “Skip obtaining driver soft-

ware from Windows Update” to stop the search.

TASCAM SERIES 102i / SERIES 208i

9

Installing the Mac dedicated software

NOTE

i

Install the Mac software on the computer before connecting the

unit to it with the USB cable.

i

Depending on the Gatekeeper setting, a warning message

might appear during installation. For information

about Gatekeeper, see“ Note about Gatekeeper” in“ 3– Installa-

tion” of the Reference Manual.

Mac dedicated software installation proce-

dures

1. Download the latest Mac dedicated software for the operat-

ing system you are using from the TEAC Global Site (http://

teac-global.com/) and save it on the computer to be used

with the unit

2. Double-click “TASCAM_SERIES_102i_208i_Installer_x.xx.dmg”,

which is the saved disk image file for the Mac dedicated soft-

ware, and double-click “

SERIES_102i_208i_Installer.pkg

” in-

side the folder that opens.

NOTE

Depending on the computer’s settings, the downloaded zip file

might not have been uncompressed automatically. In this case,

uncompress the zip file first and then double- click the disk im-

age file.

3. When the installer starts, click the “Continue” button.

4. Next, select the desired language and click the “Continue” but-

ton.

5. Click the “Read License” button and check the contents of the

Software License Agreement. If you agree to the contents of

the license, click “Agree”.

Then, click the “Next” button.

6. Next, click the “Install” button to start installation.

7. The following screen appears when installation has complet-

ed.

Click the “Close” button.

10

TASCAM SERIES 102i / SERIES 208i

Connecting the power

Use the included AC adapter (PS-P1220E) to connect a power sup-

ply to the unit as shown below.

Power outlet

PS-P1220E (included)

DC plug

In order to prevent the cord from becoming disconnected during

use, wrap it around the cord holder when connecting it.

ATTENTION

Always use the AC adapter (PS-P1220E) that was shipped with

the unit. Using a different AC adapter could cause malfunction,

overheating, fire or other problems.

NOTE

The AC adapter for the unit includes 4 types of outlet plugs. At-

tach the type of plug that matches the power outlet that you

are using.

Changing the outlet plug

NOTE

When purchased new, the included PS-P1220E AC adapter for

the unit has an outlet plug (A) already attached. There should

be no need to change the plug.

1. Move the knob (1) on the PS-P1220E AC adapter in the direc-

tion of the arrow and remove the plug (A).

2. Select the plug that matches the AC outlet from the 3 other

types included (B, C or D).

3. Move the knob (1) in the direction of the arrow again, and

attach the plug to the AC adapter.

This completes changing the outlet plug.

After changing the outlet plug, confirm that it is not loose or crook-

ed and that everything is normal before plugging it into an outlet.

ATTENTION

Do not use the adapter if there is anything abnormal about the

plug after changing it. Use when the plug is abnormal could

cause fire or electric shock.

Contact the retailer where you purchased the unit or a TEAC ser-

vice center (on the back cover) to request repair.

TASCAM SERIES 102i / SERIES 208i

11

Connecting other equipment

This is an example of SERIES 102i connections.

Precautions before making connections

0 Carefully read the operation manuals of the devices to be con-

nected and then connect them correctly.

0 Before making connections, turn this unit and all equipment to

be connected off (standby).

0 If possible, install all connected devices so that they are pow-

ered from the same AC power supply line. When using a power

strip or similar device, be sure to use one that has a thick cable

with high current capacity in order to minimize voltage fluctu-

ations in the AC power supply.

Guitars

Mic

Headphones

Examples of connections to a SERIES 102i (front)

ComputerDrum machinePowered speakers

Mic preamp with S/MUX

(When using the OPTICAL OUT (S/MUX) of a TASCAM SE-

RIES 8p Dyna as the clock master for this unit)

Examples of connections to a SERIES 102i (back)

V

CAUTION

Set the MONITOR and PHONES knobs to their minimum values

before changing the input switch setting. Failure to do so could

cause sudden loud noises from monitoring equipment, and this

could damage equipment or harm hearing.

ATTENTION

i

Input switches can be set for each channel separately. Do not

set the switch to +48V when connecting a mic that does not re-

quire phantom power.

i

Do not connect or disconnect mics when the switch is set to

+48V. Doing so could cause a loud noise and might damage this

unit and connected equipment.

i

Set the switch to +48V only when using a condenser micro-

phone that requires phantom power. Setting the switch to +48V

when a dynamic mic or other device that does not require it is

connected could damage this unit and connected equipment.

i

When using condenser mics that require phantom power and

dynamic mics together, be sure to use balanced dynamic mics.

Unbalanced dynamic mics cannot be used when phantom

power is enabled.

i

Supplying phantom power to some ribbon mics could break them.

If you are unsure, do not supply phantom power to a ribbon mic.

Connecting with iOS devices

You can use a Lightning to USB Camera Adapter* to connect the

unit to an iOS device and use it as an interface with that device.

* You must obtain a genuine Apple Lightning to USB Camera

Adapter separately.

NOTE

When connected, this unit will not provide power to the iOS

device.

Adjusting the input sound

Analog audio signals input into this device from mics, guitars, key-

boards and other audio equipment can be converted into digital

signals and transmitted to the computer via USB. You can use the

features of this unit to adjust the digital signals that are sent to the

computer. In addition, by connecting speakers (through an ampli-

fier if not powered) or headphones to this unit, you can monitor

audio signals that are input to this unit and output from the com-

puter.

Use the various controls on the front of the unit as necessary while

listening to the input sound.

SERIES 102i

SERIES 208i

Adjust the GAIN knobs (4) to adjust the analog input levels of the

1-2 input jacks (1) or 3-4 input jacks (2, SERIES 208i only) so that

the PEAK indicators (3) above and to the right of the knobs do

not light.

To listen to the monitoring signal using headphones, connect

headphones to the PHONES or jack (5) and then adjust the

PHONES knob (6).

NOTE

Check the following if you cannot hear the input sounds.

i Use the PHONES knob on the front panel to adjust the out-

put levels of the PHONES and jacks.

i Use the MONITOR knob on the front of the unit to adjust the

output levels of the LINE OUT (BALANCED) 1-2 jacks.

12

TASCAM SERIES 102i / SERIES 208i

Making various settings

NOTE

In order to enable the computer to handle digital audio signals

smoothly, other loads on the computer should be minimized as

much as possible.

We recommend that you quit unneeded applications before

use.

Opening the Settings Panel

Launch the Settings Panel software.

Windows

From the Start menu select “SERIES 102i_208i” under “TASCAM”.

Mac

Using the “Finder”, select “SERIES 102i_208i” from the “Applica-

tions” folder and launch it to open the “Settings Panel” on the com-

puter display.

Settings Panel overview

The Settings Panel has three pages.

Click a tab at the top of the Settings Panel to open that page.

0 MIXER: Make built-in mixer and effect settings.

0 INFORMATION: This shows the current status of the driver and

information about connections. You can also

make various settings.

0 ROUTING: Make output settings (and Monitor Control settings

for the SERIES 208i).

Making settings on the MIXER screen

Click the MIXER tab on the Settings Panel to open the MIXER page

as shown below.

SERIES 102i Settings Panel MIXER page in Windows

1 EQUALIZER

Equalizer settings are shown for the channel selected in the

Channel Mixer area.

2 COMPRESSOR area

Compressor settings are shown for the channel selected in the

Channel Mixer area.

3 REVERB area

This shows the reverb settings.

4 Channel Mixer area

Check and make settings for each channel.

NOTE

All channels are available when a SERIES 208i is connected.

When a SERIES 102i is connected, the INPUT 3, INPUT 4 and OPT

B1 - B8 channels cannot be used and will appear dimmed.

5 Output adjustment area

Make REVERB, AUX MASTER and STEREO MASTER settings here.

For details about other settings, see “MIXER page” in “5 - Using the

Settings Panel” of the Reference Manual.

Making settings on the INFORMATION

screen

Click the INFORMATION tab on the Settings Panel to open the IN-

FORMATION page as shown below.

Windows Settings Panel INFORMATION page

For details about settings, see“ INFORMATION page” in“ 5 - Using

the Settings Panel” of the Reference Manual.

Setting the sample clock source

1. Click the INFORMATION tab on the Settings Panel to open the

INFORMATION page as shown below.

2. Click Sample Clock Source (1) on the INFORMATION page to

set the sample clock source.

Options: INTERNAL, OPTICAL A, OPTICAL B, WORD

NOTE

When set to OPTICAL A, OPTICAL B or WORD, if no signal is input

through the corresponding connector or synchronization be-

comes impossible, “Unlocked” will appear for the Clock Source

Status item in the status area (2) and the unit’s STANDBY indi-

cator will blink. (“Manually Configured” will appear when using

OPTICAL A/B with the Rate item set to Manual.)

TASCAM SERIES 102i / SERIES 208i

13

Making settings on the ROUTING screen

Click the ROUTING tab on the Settings Panel to open the ROUTING

page as shown below.

SERIES 102i Settings Panel ROUTING screen

SERIES 208i Settings Panel ROUTING screen

NOTE

For details about other settings, see “ROUTING page” in “5 - Us-

ing the Settings Panel” of the Reference Manual.

Changing sampling frequency

The sampling frequency (44.1kHz by default) can be set using

DAW software or with the following procedure.

Windows

Change using: Control Panel

w

Sound window

w

Playback tab

w

Speakers SERIES 102i or Speakers SERIES 208i

w

Properties

w

Advanced tab

w

Default For-

mat. Then, on the Recording tab, use “Set Default”

for “Mic SERIES 102i” or “Mic SERIES 208i” to set the

same sampling frequency in the same manner.

Mac

Change using: Applications folder

w

Utilities folder

w

Audio MIDI Setup

w

Audio Devices window

w

SERIES 102i or SERIES 208i w Format.

NOTE

When shipped new from the factory, the MONITOR knob is set

to its minimum value, so no signals will be output from the LINE

OUT 1-2 (MONITOR) jacks.

Adjust the MONITOR knob as desired when using the LINE OUT

1-2 (MONITOR) jacks.

Troubleshooting

Please read this chapter if you are unable to use the unit properly

even after setting it up following the procedures in this manual.

If you are still unable to resolve your problems please contact TAS-

CAM customer support (see the end of this manual) with the fol-

lowing information about the operating environment and details

about the trouble.

Operating environment

0 Computer manufacturer :

0 Model:

0 CPU:

0 Memory (RAM) :

0 Operating system:

0 Applications used:

0 Antivirus software:

0 Wireless LAN use:

If these measures do not resolve the issue, please contact the re-

tailer where you purchased this unit or a TEAC service center.

See the end of this document for contact information.

The dedicated software cannot be installed.

1. Check the operating system

The operating system being used might not be compatible

with the software that you are trying to install.

Check the compatible operating system of the software you

are trying to install again.

2. Stop software running in the background

Antivirus software and other software that runs in the back-

ground can prevent installation.

Quit software that runs in the background and try installation

again.

The unit is connected, but the computer

does not recognize it.

1. Install the dedicated software

o

If you have not done so, install the dedicated software. (See

“Installing the dedicated software” on page 8.)

2. Change the USB port

o

This unit cannot be used with USB 1.1. Use a port that sup-

ports at least USB 2.0 or USB 3.0.

o

Do not use a USB hub with this unit. Always connect the

unit directly to a USB port on the computer.

o

If the above methods do not resolve the problem, connect

the unit to a different USB port on the computer.

14

TASCAM SERIES 102i / SERIES 208i

I cannot hear any sound even when audio is

played back on the computer.

Confirm that the MONITOR BALANCE knob on the unit is not

turned all the way to the left (toward INPUT).

If that is the case, turn the MONITOR BALANCE knob to the right

of center (toward COMPUTER).

In addition, check the status of the unit’s connection with the com-

puter. Moreover, if you make the following settings, sound will be

output through this unit, but no sound will be output by the com-

puter’s speakers or headphone jack.

Windows

0 See the “Windows Media Player” section in the “6 - Application

Guide” chapter of the Reference Manual, and make settings for

the default playback device according to the OS.

Mac

1. Quit all applications and open “System Preferences…” from

the Apple menu.

2. Open “Sound” .

3. On the “Output” tab, select “SERIES 102i” or “SERIES 208i”.

After completing the setting, restart the computer and check the

sound of playback. Depending on the application that you are us-

ing, you might need to make additional device settings.

In particular, DAW applications operate using audio engines with

settings that are different from the OS settings, so confirm the

DAW settings first after installing the dedicated software for this

unit.

Please see the manuals for the applications that you are using for

detailed setting procedures.

Sound breaks up or there is noise.

The processing load on the computer causes sound to break up

and noise to occur.

Here are some methods to reduce the load on the computer.

1. A wireless LAN and software running in the background, in-

cluding antivirus software, regularly put processing loads on

the computer, which can cause sound to break up and other

noise. Stop wireless LAN transmission, antivirus software and

other software running in the background when using this

unit.

2. Set the buffer size (latency) in the audio application that you

are using or in this unit’s Settings Panel to a larger value (Win-

dows only).

NOTE

Consult the maker of the audio application that you are using

for methods to reduce its load on your computer.

3. Change the settings of your computer so that they are optimal

for audio processing.

Using Windows

1 Open the Control Panel using the appropriate method for

the OS you are using (Windows 10/Windows 8.1/Windows

7).

i In Windows 10, open the “Control Panel”. Then, click the

“System” icon.

i In Windows 8.1, right-click the ordinary Start screen

(Metro user interface screen) and then click “All apps”.

Then, right-click “Computer” and select “Properties”.

i In Windows 7, right-click “Computer” from the Windows

Start button, and select “Properties”.

2 Click “Advanced system settings”.

3 Click “Settings” in the “Performance” section of the

“Advanced” tab of the “System Properties” window.

4 In the “Visual Effects” tab of the “Performance Options” win-

dow, select “Adjust for best performance”.

Using Mac

1 Open “System Preferences…” from the Apple menu,

and select “Energy Saver”.

2 Set “Computer sleep” to “Never”.

3 Set “Display sleep” to “ Never”.

NOTE

Depending on the Mac OS version and Macintosh computer

model, this setting might not be available.

4. Change the USB port

Since the unit might not properly function with some USB

ports, try connecting it to a different USB port.

NOTE

i

Try again after disconnecting other USB devices. (Keyboards

and mice can be left connected.)

i

Do not use a USB hub. Always connect the unit directly to a USB

port on the computer (built-in)

Specifications

Ratings

Sampling frequencies

44.1, 48, 88.2, 96, 176.4, 192 kHz

Quantization bit depth

24-bit

Analog audio input ratings

Mic inputs (balanced)

SERIES 102i: 1-2

SERIES 208i: 1-2, 3-4

(when the input switch is set to MIC/LINE)

Connector : XLR-3-31 equivalent (1: GND, 2: HOT, 3: COLD)

Input impedance: 1.5 kΩ

Rated input level:

-64 dBu (0.0005 Vrms, GAIN knob at maximum)

-6 dBu (0.388 Vrms, GAIN knob at minimum)

Maximum input level: +10 dBu (2.45 Vrms)

Gain range: 58 dB

Instrument inputs (unbalanced)

SERIES 102i: 1-2

SERIES 208i: 1-2, 3-4

(when the input switch is set to INST)

Connectors: 6.3mm (1/4”) standard TS jacks

(Tip: HOT, Sleeve: GND)

Input impedance : 1 MΩ or more

Rated input level:

-64 dBV (0.0006 Vrms, GAIN knob at maximum)

-6 dBV (0.501 Vrms, GAIN knob at minimum)

Maximum input level: +10 dBV (3.162 Vrms)

Gain range: 58 dB

TASCAM SERIES 102i / SERIES 208i

15

Line inputs (balanced)

SERIES 102i: 1-2

SERIES 208i: 1-2, 3-4

(when the input switch set to MIC/LINE)

Connectors: 6.3 mm (1/4 “) standard TRS jacks

(Tip: HOT, Ring: COLD, Sleeve: GND)

Input impedance: 10 kΩ

Rated input level:

-54 dBu (0.0015 Vrms, GAIN knob at maximum)

+4 dBu (1.228 Vrms, GAIN knob at minimum)

Maximum input level: +24 dBu (12.282 Vrms)

Gain range : 58 dB

Analog outputs

Monitor outputs (balanced, LINE OUT 1-2)

Connectors: 6.3mm (1/4”) standard TRS jacks

(Tip: HOT, Ring: COLD, Sleeve: GND)

Output impedance: 230 Ω

Nominal output level: +4 dBu (1.228 Vrms)

Maximum output level: +20 dBu (7.75 Vrms)

Line outputs (balanced, LINE OUT 3-8, on

SERIES 208i only)

Connectors: 6.3mm (1/4”) standard TRS jacks

(Tip: HOT, Ring: COLD, Sleeve: GND)

Output impedance: 230 Ω

Nominal output level: +4 dBu (1.228 Vrms)

Maximum output level: +20 dBu (7.75 Vrms)

Headphone outputs (PHONES / )

Connectors: 6.3mm (1/4”) standard stereo jacks

Maximum output:

SERIES 102i: 18mW + 18mW

SERIES 208i: 45mW + 45mW

(THD+N 0.1% or less, into 32 Ω load)

Digital audio input ratings

OPTICAL (S/MUX) IN (SERIES 208i includes A

and B)

Connectors: OPTICAL (JEITA RC-5720C)

Signal format: Multi-channel optical format

(Supports S/MUX when 88.2 k, 96 k, 176.4 k or 192 kHz.)

Control input/output

USB

Connector: 4-pin USB B-type

Transfer rate: USB 2.0 High Speed (480 Mbps)

MIDI IN connector

Connector: 5-pin DIN

Format: standard MIDI

MIDI OUT connector

Connector: 5-pin DIN

Format: standard MIDI

WORD IN connector (SERIES 208i only)

Connector: BNC

Input voltage: 2.0 Vpp - 5.0 Vpp

Input impedance: 75 Ω ±10%

Permitted frequency deviation during external synchronization:

±100 ppm

Terminal on/off switch

WORD OUT connector (SERIES 208i only)

Connector: BNC

Input voltage: 2.0 Vp-p (into 75 Ω)

Output impedance: 75 Ω ±10%

Sampling frequencies: 44.1, 48, 88.2, 96, 176.4 and 192 kHz

Audio performance

Mic amp EIN (equivalent input noise)

-129 dBu or lower

Frequency response

MIC/LINE IN

At 44.1/48 kHz, 20 Hz - 20 kHz: +0 dB/-0.4 dB (JEITA)

At 88.2/96 kHz, 20 Hz - 40 kHz: +0 dB/-0.8 dB (JEITA)

S/N ratio

109 dB

(MIC/LINE IN, GAIN knob at minimum, 20 kHz SPCL LPF+A-Weight)

110 dB

(LINE OUT, MONITOR knob at maximum, 20 kHz SPCL LPF+A-Weight)

THD + N

SERIES 102i

0.0016%

(MIC IN, 1 kHz sine wave, GAIN knob at minimum, 20 kHz

SPCL LPF)

0.0023%

(LINE IN, 1 kHz sine wave, GAIN knob at minimum, 20 kHz

SPCL LPF)

0.0014%

(LINE OUT, 1 kHz sine wave, MONITOR knob at maximum, 20

kHz SPCL LPF)

SERIES 208i

0.0013%

(MIC IN, 1 kHz sine wave, GAIN knob at minimum, 20 kHz

SPCL LPF)

0.0019%

(LINE IN, 1 kHz sine wave, GAIN knob at minimum, 20 kHz

SPCL LPF)

0.0014%

(LINE OUT, 1 kHz sine wave, MONITOR knob at maximum, 20

kHz SPCL LPF)

Crosstalk

100 dB or more

(MIC/LINE

w

LINE OUT, 1kHz sine wave, GAIN knob at mini-

mum)

16

TASCAM SERIES 102i / SERIES 208i

Computer system requirements

Check the TEAC Global Site (http://teac-global.com/) for the lat-

est information about supported operating systems.

Windows

Supported operating systems

Windows 10 32-bit

Windows 10 64-bit

Windows 8.1 32-bit

Windows 8.1 64-bit

Windows 7 32-bit SP1 or later

Windows 7 64-bit SP1 or later

(Windows Vista and Windows XP are not supported)

Computer hardware requirements

Windows computer with a USB port that supports at least USB

2.0 or USB 3.0

CPU/processor speed

2 GHz or faster dual core processor (x86)

Memory

2 GB or more

ATTENTION

Operation of this unit was confirmed using standard computers

that meet the above requirements.

This does not guarantee operation with all computers that meet

the above requirements. Even computers that meet the same

system requirements might have processing capabilities that

differ according to their settings and other operating condi-

tions.

Mac

Supported operating systems

macOS Mojave (10.14 or later)

macOS High Sierra (10.13 or later)

macOS Sierra (10.12 or later)

Computer hardware requirements

Mac with a USB port that supports at least USB 2.0 or USB 3.0

CPU/processor speed

2 GHz or faster dual core processor

Memory

2 GB or more

iOS device

Apple iOS device running iOS 10 or later

Supported audio drivers

Windows

USB Audio Class 2.0, ASIO 2.2, WDM (MME), MIDI

Mac

Core Audio, Core MIDI

iOS device

Core Audio for iPhone

General

Power

DC12V AC adapter (PS-P1220E)

Power consumption

SERIES 102i: 7.2 W

SERIES 208i: 14 W

Dimensions

SERIES 102i: 186 × 65 × 160 mm (width × height × depth)

SERIES 208i: 296 × 65 × 160 mm (width × height × depth)

Weight

SERIES 102i: 1.1 kg

SERIES 208i: 1.6 kg

Operating temperature range

5–35 °C (41–95 °F)

Dimensional drawings

SERIES 102i

186mm

65mm

160mm

SERIES 208i

296mm

65mm

160mm

0 Illustrations in this manual might differ in part from the actual

product.

0 Specifications and external appearance might be changed

without notification to improve the product.

0 Detailed specifications are provided in the Reference Manual.

TASCAM SERIES 102i / SERIES 208i

17

INSTRUCTIONS DE SÉCURITÉ IMPORTANTES

AVERTISSEMENT: POUR PRÉVENIR LES RISQUES

D'INCENDIE ET D'ÉLECTROCUTION, N'EXPOSEZ PAS CET

APPAREIL À LA PLUIE NI À L'HUMIDITÉ.

Pour le Canada

THIS CLASS B DIGITAL APPARATUS COMPLIES WITH CANADIAN

ICES-003.

CET APPAREIL NUMÉRIQUE DE LA CLASSE B EST CONFORME À

LA NORME NMB-003 DU CANADA.

CET APPAREIL NUMÉRIQUE DE LA CLASSE A EST CONFORME À

LA NORME NMB-003 DU CANADA.

Ce produit est conforme aux impératifs des

directives européennes et autres règlements de

la Commission.

1. Lisez ces instructions.

2. Conservez ces instructions.

3. Tenez compte de tous les avertissements.

4. Suivez toutes les instructions.

5. N'utilisez pas cet appareil avec de l'eau à proximité.

6. Nettoyez-le uniquement avec un chiffon sec.

7. Ne bloquez aucune ouverture de ventilation. Installez-le

conformément aux instructions du fabricant.

8. Ne l'installez pas près de sources de chaleur telles que des

radiateurs, bouches de chauffage, poêles ou autres appareils

(y compris des amplificateurs) dégageant de la chaleur.

9. Ne neutralisez pas la fonction de sécurité de la fiche

polarisée ou de terre. Une fiche polarisée a deux broches,

l'une plus large que l'autre. Une fiche de terre a deux

broches identiques et une troisième broche pour la mise à la

terre. La broche plus large ou la troisième broche servent à

votre sécurité. Si la fiche fournie n'entre pas dans votre prise,

consultez un électricien pour le remplacement de la prise

obsolète.

10. Évitez de marcher sur le cordon d'alimentation et de le

pincer, en particulier au niveau des fiches, des prises secteur,

et du point de sortie de l'appareil.

11. N'utilisez que des fixations/accessoires spécifiés par le

fabricant.

12. Utilisez-le uniquement avec le chariot, socle, trépied,

support ou table spécifié par le fabricant ou vendu avec

l'appareil. Si un chariot est utilisé, faites attention à ne pas

être blessé par un renversement lors du déplacement de

l'ensemble chariot/appareil.

13. Débranchez cet appareil en cas d'orage ou de non utilisation

prolongée.

14. Confiez toute réparation à des techniciens de maintenance

qualifiés. Une réparation est nécessaire si l'appareil a été

endommagé d'une quelconque façon, par exemple si le

cordon ou la fiche d'alimentation est endommagé, si du

liquide a été renversé sur l'appareil ou si des objets sont

tombés dedans, si l'appareil a été exposé à la pluie ou à

l'humidité, s'il ne fonctionne pas normalement, ou s'il est

tombé.

• L’appareil tire un courant nominal de veille de la prise secteur

quand son interrupteur POWER ou STANDBY/ON n’est pas en

position ON.

• La fiche secteur est utilisée comme dispositif de déconnexion

et doit donc toujours rester disponible.

• Des précautions doivent être prises en cas d'utilisation

d'écouteurs ou d'un casque avec le produit car une pression

acoustique excessive (volume trop fort) dans les écouteurs ou

dans le casque peut causer une perte auditive.

• Si vous rencontrez des problèmes avec ce produit, contactez

TEAC pour une assistance technique. N'utilisez pas le produit

tant qu'il n'a pas été réparé.

MODE D'EMPLOI

18

TASCAM SERIES 102i / SERIES 208i

ATTENTION

• N'exposez pas cet appareil aux gouttes ni aux éclaboussures.

• Ne placez pas d'objet rempli de liquide sur l'appareil, comme

par exemple un vase.

• N’installez pas cet appareil dans un espace confiné comme

une bibliothèque ou un meuble similaire.

• L’appareil doit être placé suffisamment près de la prise de

courant pour que vous puissiez à tout moment attraper

facilement la fiche du cordon d'alimentation.

• Si le produit utilise des piles/batteries (y compris un pack

de batteries ou des batteries fixes), elles ne doivent pas être

exposées au soleil, au feu ou à une chaleur excessive.

• PRÉCAUTION pour les produits qui utilisent des batteries

remplaçables au lithium: remplacer une batterie par

un modèle incorrect entraîne un risque d'explosion.

Remplacez-les uniquement par un type identique ou

équivalent.

Pour les consommateurs européens

Mise au rebut des équipements électriques et

électroniques

(a) Tous les équipements électriques et électroniques doivent

être traités séparément de la collecte municipale d'ordures

ménagères dans des points de collecte désignés par le

gouvernement ou les autorités locales.

(b) En vous débarrassant correctement des équipements

électriques et électroniques, vous contribuerez à la

sauvegarde de précieuses ressources et à la prévention

de potentiels effets négatifs sur la santé humaine et

l'environnement.

(c) Le traitement incorrect des déchets d'équipements

électriques et électroniques peut avoir des effets graves

sur l'environnement et la santé humaine en raison de la

présence de substances dangereuses dans les équipements.

(d) Le symbole de déchets d'équipements électriques

et électroniques (DEEE), qui représente une

poubelle sur roues barrée d'une croix, indique

que l'équipement électrique et électronique doit

être collecté et traité séparément des déchets

ménagers.

(e) Des systèmes de retour et de collecte sont disponibles

pour l'utilisateur final. Pour des informations plus détaillées

sur la mise au rebut des vieux équipements électriques et

électroniques, veuillez contacter votre mairie, le service

d'ordures ménagères ou le magasin dans lequel vous avez

acquis l'équipement.

ATTENTION

• N’EXPOSEZ PAS L’ÉLECTRONIQUE EN OUVRANT LE BOÎTIER OU

SES CAPOTS. AUCUNE PIÈCE INTERNE N'EST RÉPARABLE PAR

L'UTILISATEUR.

• SI VOUS RENCONTREZ DES PROBLÈMES AVEC CE PRODUIT,

CONTACTEZ LE MAGASIN DANS LEQUEL VOUS L’AVEZ ACHETÉ

POUR UNE ASSISTANCE TECHNIQUE. N'UTILISEZ PAS LE

PRODUIT TANT QU'IL N'A PAS ÉTÉ RÉPARÉ.

• L'UTILISATION DE COMMANDES, DE RÉGLAGES OU LE SUIVI

DE PROCÉDURES AUTRES QUE CE QUI EST DÉCRIT DANS

CE DOCUMENT PEUT PROVOQUER UNE EXPOSITION À UN

RAYONNEMENT DANGEREUX.

La plaque signalétique se trouve sous l’unité comme indiqué

ci-dessous.

SERIES 102i

Face avant

SERIES 208i

Face avant

Plaque signalétique

TASCAM SERIES 102i / SERIES 208i

19

Introduction

Merci beaucoup d'avoir choisi une interface audio SERIES 102i/

SERIES 208i TASCAM.

Avant de connecter et d’utiliser cette unité, veuillez prendre le

temps de lire ce mode d'emploi en totalité pour vous assurer une

bonne compréhension de sa mise en service et de son branche-

ment, ainsi que de la façon d'utiliser ses nombreuses fonctions

utiles et pratiques. Une fois la lecture de ce mode d'emploi ter-

minée, veillez à le conserver en lieu sûr pour référence ultérieure.

Vous pouvez aussi télécharger ce mode d'emploi depuis le site

mondial de TEAC (http://teac-global.com/).

Avant de brancher cette unité à un ordinateur, un pilote dédié

doit être téléchargé et installé sur l'ordinateur.

Note à propos du manuel de

référence

Ce mode d'emploi explique chacune des fonctions de cette unité.

Veuillez consulter le manuel de référence pour des informations

détaillées sur chacune des fonctions.

Vous pouvez télécharger le manuel de référence depuis le site

mondial de TEAC (http://teac-global.com/).

Éléments fournis

Ce produit est livré avec les éléments suivants.

Ouvrez l'emballage avec soin pour ne pas les endommager.

Conservez la boîte et les matériaux d'emballage pour de futurs

transports. Si un élément quelconque est manquant ou a été en-

dommagé durant le transport, veuillez contacter le magasin dans

lequel vous avez acheté cette unité.

i Unité principale ......................................................................................× 1

i Adaptateur secteur (PS-P1220E) (avec 3jeux de broches) .....× 1

i Câble USB ................................................................................................. × 1

i Jeu de guides d'installation pour logiciels DAW ........................ × 1

i Jeu de guides d'installation pour logiciels plug-ins de DAW × 1

i Mode d'emploi (ce document) incluant la garantie .................× 1

ATTENTION

Utilisez toujours l'adaptateur secteur (PS-P1220E) fourni avec

cette unité. N'utilisez jamais un adaptateur secteur fourni avec

un autre appareil. Cela pourrait entraîner des dommages, un in-

cendie, voire un choc électrique.

NOTE

L'adaptateur secteur fourni (PS-P1220E) est livré avec des bro-

ches secteur interchangeables. Veuillez consulter « Change-

ment des broches de prise électrique» en page 24.

Conventions employées dans ce

mode d'emploi

Dans ce document, les conventions suivantes sont employées:

i Les touches, connecteurs et autres parties physiques de cette

unité et des appareils connectés sont indiqués au moyen de

caractères gras comme ceci: bouton PHONES.

i Les informations qui s'affichent sur l'écran d'un ordinateur sont

indiquées sous la forme: «OK».

i Si nécessaire, des informations supplémentaires sont fournies

sous les intitulés CONSEIL, NOTE et ATTENTION.

CONSEIL

Ce sont des conseils concernant l'emploi de l'unité.

Sommaire

INSTRUCTIONS DE SÉCURITÉ IMPORTANTES ......................... 17

Introduction .............................................................................. 19

Note à propos du manuel de référence .................................. 19

Éléments fournis ....................................................................... 19

Conventions employées dans ce mode d'emploi ................... 19

Précautions concernant l'emplacement et l'emploi .............. 20

Attention à la condensation .................................................... 20

Nettoyage de l'unité ................................................................. 20

Utilisation du site mondial TEAC ............................................. 20

À propos du service d'assistance clientèle TASCAM .............. 20

Nomenclature et fonctions des parties .................................. 20

Face avant ................................................................................................... 20

Face arrière ................................................................................................. 21

Installation du logiciel dédié ................................................... 22

Installation des logiciels dédiés pour Windows ............................ 22

Installation du logiciel dédié pour Mac ............................................ 23

Connexion de l'alimentation ................................................... 24

Changement des broches de prise électrique............................... 24

Branchement d'autres équipements ...................................... 25

Branchement à des appareils iOS ............................................ 25

Réglage du son entrant ............................................................ 25

Divers réglages ......................................................................... 26

Ouverture du panneau de réglages (Settings Panel) .................. 26

Présentation du panneau de réglages ............................................. 26

Réglages en écran MIXER ...................................................................... 26

Réglages en écran INFORMATION ...................................................... 26

Réglages en écran ROUTING ................................................................ 27

Changement de fréquence d'échantillonnage ....................... 27

Guide de dépannage ................................................................ 27

Caractéristiques techniques .................................................... 28

Données ...................................................................................................... 28

Valeurs d'entrée audio analogique .................................................... 28

Sorties analogiques ................................................................................. 29

Valeurs d'entrée audio numériques .................................................. 29

Entrée/sortie de commande ................................................................ 29

Performances audio ................................................................................ 29

Configurations informatiques requises .................................. 30

Windows ...................................................................................................... 30

Mac ................................................................................................................ 30

Appareil iOS ................................................................................................ 30

Pilotes audio pris en charge ................................................................. 30

Caractéristiques générales ...................................................... 30

Dessins avec cotes .................................................................... 30

20

TASCAM SERIES 102i / SERIES 208i

NOTE

Ce sont des explications supplémentaires et des descriptions de

cas particuliers.

ATTENTION

Ne pas suivre ces instructions peut par exemple entraîner des

dommages pour l'équipement ou la perte de données.

V

MISE EN GARDE

Le non-respect de ces instructions peut entraîner des blessures.

Précautions concernant

l'emplacement et l'emploi

i La plage de température de fonctionnement de cette unité se

situe entre 5ºC et 35ºC.

i Ne placez pas cette unité dans les types d'emplacement sui-

vants.

Cela pourrait dégrader la qualité sonore ou causer des mauvais

fonctionnements.

Lieux sujets à des vibrations importantes

Près d'une fenêtre ou à un autre endroit exposé directement

au soleil

Près de chauffages ou dans des lieux extrêmement chauds

Lieux extrêmement froids

Lieux très humides ou mal aérés

Lieux très poussiéreux

i Pour permettre une bonne dispersion thermique, ne placez

rien sur le dessus de l'unité.

i Ne placez pas cette unité sur un amplificateur de puissance ou

un autre appareil générant de la chaleur.

Attention à la condensation

De la condensation peut se produire si l'unité est déplacée d'un

endroit froid à un endroit chaud, est utilisée dans une pièce qui

vient d'être chauffée ou soumise à des changements brutaux de

température. Pour empêcher cela ou si cela se produit, laissez

l’unité une ou deux heures à la température de la nouvelle pièce

avant de l'utiliser.

Nettoyage de l'unité

Essuyez l'unité avec un chiffon sec et doux pour la nettoyer. Ne l'es-

suyez pas avec des lingettes de nettoyage contenant des produits

chimiques, du diluant, de l'alcool ou d'autres agents chimiques.

Cela pourrait endommager la surface ou causer une décoloration.

Utilisation du site mondial TEAC

Vous pouvez télécharger des mises à jour pour cette unité depuis

le site mondial:

http://teac-global.com/

Dans la section TASCAM Downloads (téléchargements TASCAM),

sélectionnez la langue souhaitée afin d'ouvrir la page de téléchar-

gement du site web pour cette langue.

À propos du service d'assistance

clientèle TASCAM

Les produits TASCAM ne bénéficient d’une assistance et d’une ga-

rantie que dans leur pays/région d'achat.

Pour bénéficier d’une assistance après l'achat, recherchez dans

la liste des distributeurs TASCAM fournie sur le site mondial TEAC

(http:// teac-global.com/) la société ou le représentant local pour

la région dans laquelle vous avez acheté le produit et contactez

cette organisation.

Pour toute demande, l'adresse physique ou URL du magasin ou

du site marchand chez qui a été effectué l’achat ainsi que la date

d’achat sont requises.

De plus, la carte de garantie et une preuve d'achat peuvent égale-

ment être nécessaires.

Nomenclature et fonctions des

parties

Face avant

SERIES 102i

SERIES 208i

1 Voyants de signal (SIG)

Ils s'allument en vert si des signaux (d'au minimum -32dBFS)

entrent.

2 Boutons GAIN

Utilisez-les pour régler les niveaux d'entrée par les prises d’en-

trée.

3 Voyants de crête (PEAK)

Ils s'allument en rouge si les signaux s’approchent du niveau de

distorsion (-1dBFS ou plus).

Réglez le niveau pour que les voyants PEAK ne s’allument pas

en rouge.

4 Voyant USB

Ce voyant indique l'état de l'unité en étant allumé, clignotant

ou éteint.

État Signification

Allumé Bonne connexion USB

Clignotant

Mauvaise connexion USB (déconnexion ou

survenue d’une erreur)

Éteint Fonctionnement en mode autonome

5 Voyant

Ce voyant s'allume quand le commutateur STANDBY est en-

clenché. Il clignote si la source d'horloge ou l'entrée optique

est irrégulière (quand la source d'horloge est réglée sur WORD

ou OPTICAL).

6 Bouton MONITOR BALANCE

Utilisez-le pour régler la balance entre les signaux reçus par les

prises d'entrée de cette unité et ceux sortant de l'ordinateur.

Le volume des signaux reçus par les prises d'entrée de cette

unité augmente d'autant plus que le bouton MONITOR BA-

LANCE est tourné vers la gauche (INPUT) et celui des signaux

ページが読み込まれています...

Tascam 102i Series 取扱説明書

このマニュアルも適しています

Tascam 102i Series 取扱説明書

他の言語で

関連論文

その他のドキュメント