Make sure that all parts are present before use.
Thank you for purchasing a “TIGER” Stainless Steel Bottle.
Please read the instructions completely before use.
Keep these instructions for future reference.
MME-A
MODEL
Instructions
Stainless Steel Bottle
Safety Precautions
Do not use chlorine-based
bleaches or acetic acid
solutions when cleaning the
product.
Do not use chlorine bleach for
carrying case.
Do not remove the protective
sheet on the underside of the
product.
Do not attempt to add any
beverages directly from the
spout while the cap unit is set.
Do not swing the product while
holding the strap.
Keep the product in an upright
position at all times.
Do not place the product in the
carrying case if its exterior is
wet.
Important!
Do not add hot water.
Cold drinks only.
Keep out of reach of children.
Do not let children play with the
product.
Do not put dry ice or carbonated
beverages in the product.
Close the direct drink cap unit
firmly and check that it is locked.
Do not store milk, dairy products,
or certain fruit juices in the
product.
Noncompliance with these
instructions may result in scald
or injury.
Consume beverage within the day
to prevent from spoiling.
If the beverage is left for an
extended period, spoilage can lead
to the creation of gas, raising the
pressure inside the product.
This can cause the contents to
burst out or damage the direct drink
cap unit, possibly resulting in injury.
Do not place the product near
stoves, open flames, or other
sources of extreme heat.
Do not fill the product above the
maximum level shown below.
Do not use the product for any
purpose other than keeping bev-
erages cold for drinking.
Do not knock over, drop or
expose the product to
excessive shocks.
Do not disassemble or attempt
to repair the product by yourself.
Be sure to clean the product
immediately after use, especially
after consuming sports drinks.
Do not store soups or beverages
containing salt in the product.
Do not leave the product in a
bag for a long time.
To keep your beverage cool longer, pour a small amount of cold
water into the body, and let it sit for one or two minutes. Discard
the cold water after precooling.
Set the product into the carrying case.
Clean after every use.
Use mild kitchen detergent.
Use a sponge or soft cloth.
Be sure to clean the spout and the gaskets after every use.
Don’t put the carrying case into washing machine.
Attaching and Removing the gaskets
Be sure to wipe off with dry cloth.
Do not place in a dishwasher/dryer.
Be sure zipper guard is straight
when zipping up.
Specifications
Replacing and Purchasing
Consumable Parts
Before contacting customer
service
The gaskets and the direct drink cap unit are
consumable parts. Check once a year for
damage/deterioration. If heavily stained or
loose, replace them.
For replacement parts, contact customer
service or the shop where you purchased
this product.
The utmost measures have been taken to
ensure the quality of this product.
However, should the product be defective,
contact your dealer and provide the
following information.
1. Product name
2. Model Number
3. Description of trouble
(As detailed as possible)
4. Purchase date
Feel free to send any questions or
comments about this product to the shop
where you purchased it.
For the purpose of performance improvement, designs, specifications and parts shown in this
publication are subject to change without notice.
123
MME-A
TIGER HANBAI (H.K.) CO.,LTD.
Rm. 1006B, 10/FI., Join-in Hang Sing Centre, 71 - 75 Container Port Road,
Kwai Chung, N.T.
Tel: (852) 2418-0912 Fax: (852) 2418-0911
JAPAN TIGER CORPORATION OF U.S.A.
2730 Monterey Street, Suite 105 Torrance, CA 90503
Tel: (310) 787-1985 Fax: (310) 787-1986
URL: http://usa.tiger-corporation.com
TIGER CORPORATION
Head Office: 3-1 Hayamicho, Kadoma City, Osaka 571-8571, Japan
URL : http://www.tiger.jp/global
How to Use
How to Clean
Capacity Cold retention
1.0 L / 33.8 oz Less than 9°C • 48°F (6hours)
1.5 L / 50.7 oz Less than 8°C • 46°F (6hours)
When removing the gaskets, refer to the illustrations.
Attach the gaskets to the proper position and direction.
Approx.
1cm•1/2-inch
To remove To attach Cold retention has been calculated under the condition of adding cold water at 4°C ±1°C • 39°F±2°F
and leaving it in a room temperature of 20°C±2°C • 68°F±4°F for 6hours.
Capacity is the actual volume of water that can be stored into the product when the spout is closed.
This is not the “Maximum level” volume described in “Safety Precautions”.
Cold drinks only
Make sure the carrying case is
dry.
Ice changes the inner pressure
so the gasket may dislocate.
If this happens, set it back into
it’s proper position.
Fit the end of a soft pointed rod (e.g.:
toothpick) into the groove and pull out
the gasket. Do not use metal skewers.
Insert securely into the groove.
1
2
Spout gasket
Lid gasket
Safety lock
Body
Protective sheet
Direct
ap unit
Cap gasket
Button
Cap Spout
Lid gasket
Lid
Maximum level
(slightly less)
Zipper
Carrying
case
Zipper guard
is bent inward
Remove Spout
gasket
Groove
Small slot Spout gasket
Lid gasket
Make sure that all parts are present before use.
Thank you for purchasing a “TIGER” Stainless Steel Bottle.
Please read the instructions completely before use.
Keep these instructions for future reference.
MME-A
MODEL
Instructions
Stainless Steel Bottle
Safety Precautions
Do not use chlorine-based
bleaches or acetic acid
solutions when cleaning the
product.
Do not use chlorine bleach for
carrying case.
Do not remove the protective
sheet on the underside of the
product.
Do not attempt to add any
beverages directly from the
spout while the cap unit is set.
Do not swing the product while
holding the strap.
Keep the product in an upright
position at all times.
Do not place the product in the
carrying case if its exterior is
wet.
Important!
Do not add hot water.
Cold drinks only.
Keep out of reach of children.
Do not let children play with the
product.
Do not put dry ice or carbonated
beverages in the product.
Close the direct drink cap unit
firmly and check that it is locked.
Do not store milk, dairy products,
or certain fruit juices in the
product.
Noncompliance with these
instructions may result in scald
or injury.
Consume beverage within the day
to prevent from spoiling.
If the beverage is left for an
extended period, spoilage can lead
to the creation of gas, raising the
pressure inside the product.
This can cause the contents to
burst out or damage the direct drink
cap unit, possibly resulting in injury.
Do not place the product near
stoves, open flames, or other
sources of extreme heat.
Do not fill the product above the
maximum level shown below.
Do not use the product for any
purpose other than keeping bev-
erages cold for drinking.
Do not knock over, drop or
expose the product to
excessive shocks.
Do not disassemble or attempt
to repair the product by yourself.
Be sure to clean the product
immediately after use, especially
after consuming sports drinks.
Do not store soups or beverages
containing salt in the product.
Do not leave the product in a
bag for a long time.
To keep your beverage cool longer, pour a small amount of cold
water into the body, and let it sit for one or two minutes. Discard
the cold water after precooling.
Set the product into the carrying case.
Clean after every use.
Use mild kitchen detergent.
Use a sponge or soft cloth.
Be sure to clean the spout and the gaskets after every use.
Don’t put the carrying case into washing machine.
Attaching and Removing the gaskets
Be sure to wipe off with dry cloth.
Do not place in a dishwasher/dryer.
Be sure zipper guard is straight
when zipping up.
Specifications
Replacing and Purchasing
Consumable Parts
Before contacting customer
service
The gaskets and the direct drink cap unit are
consumable parts. Check once a year for
damage/deterioration. If heavily stained or
loose, replace them.
For replacement parts, contact customer
service or the shop where you purchased
this product.
The utmost measures have been taken to
ensure the quality of this product.
However, should the product be defective,
contact your dealer and provide the
following information.
1. Product name
2. Model Number
3. Description of trouble
(As detailed as possible)
4. Purchase date
Feel free to send any questions or
comments about this product to the shop
where you purchased it.
For the purpose of performance improvement, designs, specifications and parts shown in this
publication are subject to change without notice.
123
MME-A
TIGER HANBAI (H.K.) CO.,LTD.
Rm. 1006B, 10/FI., Join-in Hang Sing Centre, 71 - 75 Container Port Road,
Kwai Chung, N.T.
Tel: (852) 2418-0912 Fax: (852) 2418-0911
JAPAN TIGER CORPORATION OF U.S.A.
2730 Monterey Street, Suite 105 Torrance, CA 90503
Tel: (310) 787-1985 Fax: (310) 787-1986
URL: http://usa.tiger-corporation.com
TIGER CORPORATION
Head Office: 3-1 Hayamicho, Kadoma City, Osaka 571-8571, Japan
URL : http://www.tiger.jp/global
How to Use
How to Clean
Capacity Cold retention
1.0 L / 33.8 oz Less than 9°C • 48°F (6hours)
1.5 L / 50.7 oz Less than 8°C • 46°F (6hours)
When removing the gaskets, refer to the illustrations.
Attach the gaskets to the proper position and direction.
Approx.
1cm•1/2-inch
To remove To attach Cold retention has been calculated under the condition of adding cold water at 4°C ±1°C • 39°F±2°F
and leaving it in a room temperature of 20°C±2°C • 68°F±4°F for 6hours.
Capacity is the actual volume of water that can be stored into the product when the spout is closed.
This is not the “Maximum level” volume described in “Safety Precautions”.
Cold drinks only
Make sure the carrying case is
dry.
Ice changes the inner pressure
so the gasket may dislocate.
If this happens, set it back into
it’s proper position.
Fit the end of a soft pointed rod (e.g.:
toothpick) into the groove and pull out
the gasket. Do not use metal skewers.
Insert securely into the groove.
1
2
Spout gasket
Lid gasket
Safety lock
Body
Protective sheet
Direct
ap unit
Cap gasket
Button
Cap Spout
Lid gasket
Lid
Maximum level
(slightly less)
Zipper
Carrying
case
Zipper guard
is bent inward
Remove Spout
gasket
Groove
Small slot Spout gasket
Lid gasket
MME-A
123
MME-A
TIGER CORPORATION
Head Office: 3-1 Hayamicho, Kadoma City, Osaka 571-8571, Japan
: http://www.tiger-corporation.tw
1
2
( )
MME-A
123
MME-A
TIGER CORPORATION
Head Office: 3-1 Hayamicho, Kadoma City, Osaka 571-8571, Japan
: http://www.tiger-corporation.tw
1
2
( )
/