Yamaha RX-V2085 クイックスタートガイド

Precautions ........................................................... 2

Preparations........................................................ 10

Playback.............................................................. 21

English

注意事项.............................................................. 30

准备工作.............................................................. 38

播放..................................................................... 50

中文

AV Receiver

Ampli-Tuner Audio-Vidéo

Quick Start Guide

快速启动指南

EN

ZH-CH

UTA

2 En

The above warning is located on the rear of the unit.

• Explanation of Graphical Symbols

The lightning flash with arrowhead symbol, within an equilateral triangle, is

intended to alert you to the presence of uninsulated “dangerous voltage” within the

product’s enclosure that may be of sufficient magnitude to constitute a risk of

electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert you to the

presence of important operating and maintenance (servicing) instructions in the

literature accompanying the appliance.

1 Read these instructions.

2 Keep these instructions.

3 Heed all warnings.

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with dry cloth.

7 Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8 Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus

(including amplifiers) that produce heat.

9 Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two

blades with one wider than the other. A grounding type plug has two blades and a third grounding

prong. The wide blade or the third prong are provided for your safety. If the provided plug does not

fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10 Protect the power cord from being walked on or pinched particularly at plugs, convenience

receptacles, and the point where they exit from the apparatus.

11 Only use attachments/accessories specified by the manufacturer.

12 Use only with the cart, stand, tripod, bracket, or table specified by the

manufacturer, or sold with the apparatus. When a cart is used, use caution when

moving the cart/apparatus combination to avoid injury from tip-over.

13 Unplug this apparatus during lightning storms or when unused for long periods of

time.

14 Refer all servicing to qualified service personnel. Servicing is required when the

apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has

been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or

moisture, does not operate normally, or has been dropped.

IMPORTANT SAFETY INSTRUCTIONS

CAUTION

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

RISK OF ELECTRIC

SHOCK DO NOT OPEN

IMPORTANT

Please record the serial number of this unit in the space below.

MODEL:

Serial No.:

The serial number is located on the rear of the unit. Retain this booklet in a safe place for future

reference.

En 3

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA.

FCC/IC NOTICE (U.S.A. and Canada)

This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled

environment and meets the FCC radio frequency (RF) Exposure Guidelines and RSS-102 of the IC

radio frequency (RF) Exposure rules. This equipment should be installed and operated keeping the

radiator at least 20cm or more away from person’s body.

This device complies with Part 15 of FCC Rules and Industry Canada licence-exempt RSS standard(s).

Operation is subject to the following two conditions:

(1) this device may not cause interference, and

(2) this device must accept any interference, including interference that may cause undesired operation

of this device.

This transmitter must not be co-located or operated in conjunction with any other antenna or

transmitter.

(for Canada)

5150-5350 MHz band is restricted to indoor operation only.

High-power radars are allocated as primary users (i.e. priority users) of the bands

5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to

LE-LAN devices.

FCC INFORMATION (USA)

1 IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions contained in this manual, meets FCC

requirements. Modifications not expressly approved by Yamaha may void your authority,

granted by the FCC, to use the product.

2 IMPORTANT: When connecting this product to accessories and/or another product use only

high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all

installation instructions. Failure to follow instructions could void your FCC authorization to use

this product in the USA.

3 NOTE: This product has been tested and found to comply with the requirements listed in FCC

Regulations, Part 15 for Class “B” digital devices. Compliance with these requirements provides

a reasonable level of assurance that your use of this product in a residential environment will not

result in harmful interference with other electronic devices.

This equipment generates/uses radio frequencies and, if not installed and used according to the

instructions found in the users manual, may cause interference harmful to the operation of other

electronic devices.

Compliance with FCC regulations does not guarantee that interference will not occur in all

installations. If this product is found to be the source of interference, which can be determined by

turning the unit “OFF” and “ON”, please try to eliminate the problem by using one of the following

measures:

Relocate either this product or the device that is being affected by the interference.

Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line

filter/s.

In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300

ohm ribbon lead, change the lead-in to coaxial type cable.

If these corrective measures do not produce satisfactory results, please contact the local retailer

authorized to distribute this type of product. If you can not locate the appropriate retailer, please

contact Yamaha Corporation of America A/V Division, 6600 Orangethorpe Avenue, Buena Park,

CA 90620, USA.

The above statements apply ONLY to those products distributed by Yamaha Corporation of

America or its subsidiaries.

COMPLIANCE INFORMATION STATEMENT (DECLARATION OF CONFORMITY

PROCEDURE)

Responsible Party: Yamaha Corporation of America A/V Division

Address: 6600 Orangethorpe Avenue, Buena Park, CA 90620

Telephone: 714-522-9011

Type of Equipment: AV Receiver

Model Name: RX-V2085

CAN ICES-3(B)/NMB-3(B)

4 En

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE USE. BE

SURE TO FOLLOW THESE INSTRUCTIONS.

The precautions listed below are to prevent risk of harm to the

user and others, as well as to prevent property damage, and to

help the user use this unit properly and safely. Be sure to follow

these instructions.

After reading this manual, be sure to keep it in a safe place where it can be

referenced at any time.

WARNING

This content indicates “risk of serious injury or death.”

Power supply/power cord

• Do not do anything that could damage the power cord.

- Do not place it near a heater.

- Do not bend it excessively or alter it.

- Do not scratch it.

- Do not place it under a heavy object.

Using the power cord/adaptor with the core of the cord exposed could cause electric shocks

or a fire.

• Do not touch the power plug or cord if there is a chance of lightning. Failure to observe this

may cause electric shocks.

• Use this unit with the power supply voltage printed on it. Failure to connect to an

appropriate AC outlet may cause a fire, electric shocks, or malfunctions.

• Be sure to use the power cord. Also, do not use the supplied power cord for other units.

Failure to observe the above may cause a fire, burns, or malfunctions.

• Check the electric plug periodically and remove any dirt or dust which may have

accumulated on it. Failure to observe this may cause a fire or electric shocks.

• When setting up the unit, make sure that the AC outlet you are using is easily accessible. If

some trouble or malfunction occurs, immediately turn off the power switch and disconnect

the plug from the AC outlet. Even when the power switch is turned off, as long as the power

cord is not unplugged from the wall AC outlet, the unit will not be disconnected from the

power source.

• If you hear thunder or suspect approaching lightning, quickly turn off the power switch and

pull the power plug from the AC outlet. Failure to observe this may cause a fire or

malfunctions.

• If not using the unit for long periods of time, be sure to pull the power plug from the AC

outlet. Failure to observe this may cause a fire or malfunctions.

Do not disassemble

• Do not disassemble or modify this unit. Failure to observe this may cause a fire, electric

shocks, injury, or malfunctions. If you notice any irregularities, be sure to request an

inspection or repair from the dealer where you purchased the unit or from qualified Yamaha

service personnel.

Water warning

• Do not expose the unit to rain, use it near water or in damp or wet conditions, or place on it

any containers (such as vases, bottles or glasses) containing liquids which might spill into

any openings or places where water may drop. A liquid such as water getting into the unit

may cause a fire, electric shocks, or malfunctions. If any liquid such as water seeps into the

device, turn off the power immediately and unplug the power cord from the AC outlet. Then,

request an inspection from the dealer where you purchased the unit or from qualified

Yamaha service personnel.

• Never insert or remove an electric plug with wet hands. Do not handle this unit with wet

hands. Failure to observe this may cause electric shocks or malfunctions.

Fire warning

• Do not place any burning items or open flames near the unit, since they may cause a fire.

Maintenance and care

• Do not use aerosols or spray-type chemicals that contain combustible gas for cleaning or

lubrication. The combustible gas will remain inside the unit, which may cause explosion or

fire.

Battery use

• Do not disassemble a battery. If the contents of the battery get on your hands or in your

eyes, it can cause blindness or chemical burns.

• Do not dispose of batteries in fire. Doing so may result in the battery bursting, causing a fire

or injury.

• Be sure to request inspections or repairs from the dealer where you

purchased the unit or from qualified Yamaha service personnel.

• Yamaha cannot be held responsible for injury to you or damage of

the products caused by improper use or modifications to the unit, or

data that is lost or destroyed.

• This product is for ordinary homes. Do not use for applications

requiring high reliability, such as managing lives, health care or

high-value assets.

En 5

• Do not expose a battery to high temperatures, such as direct sunlight or a fire. The battery

may burst, causing a fire or injury.

• Do not attempt to recharge batteries that are not intended to be charged. Charging could

cause the battery to burst or leak, which can cause blindness, chemical burns, or injury.

• If the batteries do leak, avoid contact with the leaked fluid. If the battery fluid should come in

contact with your eyes, mouth, or skin, wash immediately with water and consult a doctor.

Battery fluid is corrosive and may possibly cause loss of sight or chemical burns.

Wireless unit

• Do not use this unit near medical devices or inside medical facilities. Radio waves from this

unit may affect electro-medical devices.

• Do not use this unit within 15 cm (6 in) of persons with a heart pacemaker implant or a

defibrillator implant. Radio waves from this unit may affect electro-medical devices, such as

a heart pacemaker implant or defibrillator implant.

If you notice any abnormality

• If any of the following abnormalities occur, immediately turn off the power and disconnect

the power plug. If any of the following abnormalities occur, immediately turn off any

amplifiers and receivers.

- The power cord/plug is damaged.

- An unusual smell or smoke is emitted from the unit.

- Foreign material gets into the interior of the unit.

- There is a loss of sound during use.

- There is a crack or damage in the unit.

Continued use could cause electric shocks, a fire, or malfunctions. Immediately request an

inspection or repair from the dealer where you purchased the unit or from qualified Yamaha

service personnel.

• Be careful not to drop or apply strong impact to this unit. If you suspect the unit may have

been damaged due to dropping or impact, immediately turn off the power and pull the power

plug from the AC outlet. Failure to observe this may cause electric shocks, a fire, or

malfunctions. Immediately request an inspection from the dealer where you purchased the

unit or from qualified Yamaha service personnel.

CAUTION

This content indicates “risk of injury.”

Power supply/power cord

• Do not use an AC outlet where the power plug fits loosely when inserted. Failure to observe

this may cause a fire, electric shocks, or burns.

• When removing the electric plug from the unit or an AC outlet, always hold the plug itself

and not the cord. Pulling by the cord can damage it and cause electric shocks or a fire.

• Insert the power plug firmly all the way into the AC outlet. Using the unit when it is not

plugged in sufficiently can cause dust to accumulate on the plug, causing a fire or burns.

Installation

• Do not place the unit in an unstable position where it might accidentally drop or fall over and

cause injuries.

• Do not block this unit's ventilation holes (cooling slits). This unit has ventilation holes on the

top/side/bottom to prevent the internal temperature from becoming too high. Failure to

observe this may trap heat inside the unit, causing a fire or malfunctions.

• When installing this unit:

- Do not cover it with any cloth.

- Do not install it on a carpet or rug.

- Make sure the top surface faces up; do not install on its sides or upside down.

- Do not use the device in a confined, poorly-ventilated location.

Failure to observe the above may trap heat inside the unit, causing a fire or malfunctions.

Ensure that there is adequate space around the unit: at least 30 cm (11-3/4 in) on top,

20 cm (7-7/8 in) on the sides, and 20 cm (7-7/8 in) on the rear.

• Do not install the unit in places where it may come into contact with corrosive gases or salt

air. Doing so may result in malfunction.

• Avoid being near the unit during a disaster, such as an earthquake. Since the unit may turn

over or fall and cause injury, quickly move away from the unit and go to a safe place.

• Before moving this unit, be sure to turn off the power switch and disconnect all connection

cables. Failure to observe this may damage the cables or cause you or someone else to

trip and fall.

• When transporting or moving the unit always use two or more people. Attempting to lift the

unit by yourself may damage your back, result in other injury, or cause damage to the unit

itself.

• For proper installation of the outdoor antenna, make sure to have it done by the dealer from

where you purchased the unit or by qualified service personnel. Failure to observe this may

cause the installation to fall and result in injury. Installation requires special skills and

experience.

Hearing loss

• Do not use the unit/speakers or headphones for a long period of time at a high or

uncomfortable volume level, since this can cause permanent hearing loss. If you

experience any hearing loss or ringing in the ears, consult a physician.

• Before connecting the unit to other devices, turn off the power for all devices. Also, before

turning the power of all devices on or off, make sure that all volume levels are set to the

minimum. Failing to do so may result in hearing loss, electric shock, or device damage.

• When turning on the AC power in your audio system, always turn on the amplifier or

receiver LAST, to avoid hearing loss and speaker damage. When turning the power off, the

amplifier or receiver should be turned off FIRST for the same reason. Failure to observe the

above may cause hearing impairment or speaker damage.

Maintenance

• Remove the power plug from the AC outlet before cleaning the unit. Failure to observe this

may cause electric shocks.

6 En

Handling caution

• Do not touch the surface having this label. Doing so may cause burns. The

label on the device indicates that the surface to which the label is attached may

become hot during operation.

• Do not insert your hand or fingers into the ventilation holes of this unit. Failure to observe

this may cause injury.

• Do not insert foreign materials such as metal or paper into the ventilation holes of this unit.

Failure to observe this may cause a fire, electric shocks, or malfunctions. If foreign material

gets into the unit, immediately shut off the power and pull the power plug from the AC outlet

and request an inspection from the dealer where you purchased the unit or from qualified

Yamaha service personnel.

• Do not do the following:

- put heavy items on top of the equipment.

- place the equipment in a stack.

- apply unreasonable force to buttons, switches, input/output terminals, etc.

• Avoid pulling the connected cables to prevent injuries or damage to the unit by causing it to

fall.

Battery use

• Always replace all batteries at the same time. Do not use new batteries together with old

ones. Using new ones with old ones could cause a fire, burns, or inflammation due to fluid

leaks.

• Do not use batteries other than specified batteries. Doing so cause fire, burns, or

inflammation due to leakage.

• Do not mix battery types, such as alkaline batteries with manganese batteries, or batteries

from different makers, or different types of batteries from the same maker, since this can

cause a fire, burns, or inflammation due to fluid leaks.

• Keep batteries away from children. A child could accidentally swallow a battery. Failure to

observe this may also cause inflammation due to battery fluid leaks.

• Do not put in a pocket or bag, carry, or store batteries together with pieces of metal. The

battery could short, burst, or leak, causing a fire or injury.

• Always make sure all batteries are inserted in conformity with the +/- polarity markings.

Failure to do so might result in a fire, burns, or inflammation due to fluid leaks.

• When the batteries run out, or if the unit is not to be used for a long time remove the

batteries from the remote control to prevent possible leakage of the battery fluid.

• When storing or discarding batteries, insulate the terminal area by applying tape, or some

other protection. Mixing them with other batteries or metal objects can cause a fire, burns,

or inflammation due to fluid.

Notice

Indicates points that you must observe in order to prevent

product failure, damage or malfunction and data loss.

Power supply/power cord

• If not using the unit for a long period of time, be sure to pull the power plug from the outlet.

Even if the z (Standby/On) switch has been turned off (the screen display is off), a minute

current is still flowing.

Installation

• Do not use this unit in the vicinity of other electronic equipment, such as a TV, radio, or

mobile phone. Failure to observe this may cause this unit or the TV or radio to produce

noise.

• Do not use this unit in a location that is exposed to direct sunlight, that becomes extremely

hot, such as near a heater, or extremely cold, or that is subject to excessive dust or

vibration. Failure to observe this may cause the unit's panel to become deformed, the

internal components to malfunction, or for operation to become unstable.

• Install this unit as far away from other electronic equipment as possible.

Digital signals from this unit may interfere with other electronic equipment.

• If using a wireless function, avoid installing this unit near metal walls or desks, microwave

ovens, or other wireless network devices.

Obstructions could shorten the transmission distance.

Connections

• If connecting external units, be sure to thoroughly read the manual for each unit and

connect them in accordance with the instructions.

Failure to properly handle a unit in accordance with the instructions could cause

malfunctions.

• Do not connect this unit to industrial units.

Digital audio interface standards for consumer use and industrial use are different. This unit

has been designed to connect to a consumer-use digital audio interface. Connections to an

industrial-use digital audio interface could not only cause this unit to malfunction, but could

also damage the speakers.

Handling

• Do not place vinyl, plastic, or rubber products on this unit. Failure to observe this may cause

discoloration or deformation in the panel of this unit.

• If the ambient temperature changes drastically (such as during unit transportation or under

rapid heating or cooling) and there is a chance condensation may have formed in the unit,

leave the unit for several hours without turning on the power until it is completely dry before

use. Using the unit while there is condensation can cause malfunctions.

En 7

Maintenance

• When cleaning the unit, use a dry, soft cloth. Using chemicals such as benzine or thinner,

cleaning agents, or chemical scrubbing cloths can cause discoloration or deformation.

Batteries

• Be sure to discard used batteries in accordance with local regulations.

Information

About content in this manual

• The illustrations and screens in this manual are for instructional purposes only.

• The company names and product names in this manual are the trademarks or registered

trademarks of their respective companies.

• Software may be revised and updated without prior notice.

8 En

Introduction

• This unit is a product for enjoying music and video at home.

• This document explains basic speaker system setup and unit configuration,

followed by step-by-step instructions. Basic operations, such as playing

Blu-ray Discs, DVDs, and radio content, are also explained.

• In this document, the RX-V3085 is used for illustration purposes. Some

parts or components, such as jacks, may vary by specific model. Such

differences are indicated as required.

The unit is equipped with a number of other functions not described in this

document. For more information about this product, refer to the Owner’s

Manual on the Yamaha website.

Follow one of the methods described below to view the latest Owner’s

Manual.

In HTML format

• Scan the QR code found on the front cover of this document.

• Visit the following website.

http://avpro.global.yamaha.com/manual/avr/rxv3085/

In PDF format

• Visit the following website.

http://download.yamaha.com/

[For U.S. customers only]

Visit the following website for additional information, FAQ’s, downloads such

as “Owner’s Manual” and product updates.

http://usa.yamaha.com/support/

Opening and closing the front panel door

Press the bottom of the door gently to open it when using controls or jacks

behind the front panel door. Keep the door closed when controls or jacks

behind the front panel door are not in use. (Be careful not to trap your fingers.)

Trademarks and trade names used in this document are those of their

respective owners. See the Owner’s Manual for more information.

En 9

Features

The unit is also capable of the following, which are not described in this

document. See the Owner’s Manual to help you get the most out of the unit.

• Playing music files stored on a media server (PC or NAS)

• Playing iTunes music or iPhone/iPad/iPod touch music over a network

(AirPlay)

• Playing music in multiple rooms (Zone function)

• Configuring the advanced settings (ADVANCED SETUP menu)

For more information, see “What you can do with the unit” in the Owner’s

Manual.

AV SETUP GUIDE

AV SETUP GUIDE is an app that guides you

through the process of connecting a TV or playback

device, such as a BD/DVD or CD player, and

speakers to the AV receiver. Search “AV SETUP

GUIDE” on the App Store or Google Play for

details.

10 En

1

Preparation

Confirming package contents

Preparing cables

The following cables (not supplied) are required to build the system described in this document.

• Speaker cables (depending on the number of speakers)

• Audio pin cable (x1)

• HDMI cables (x3)

• Network cable (x1) (when connecting to a router via a network cable)

Remote control

Batteries

(AAA, LR03, UM-4) (x2)

AM antenna

(Except for Australia model)

FM antenna

(Except for Australia model)

One of the above is supplied depending on

the region of purchase.

YPAO microphone

Power cable

The supplied power cable varies

depending on the region of purchase.

DAB/FM antenna

(Australia model)

Microphone base Pole

Use to measure angle/height during YPAO.

Quick Start Guide (this booklet)

En 11

2

Connecting speakers/subwoofer

Positioning speakers

Use the diagram as a reference for positioning speakers.

1 / 2 Front speaker (L/R)

3 Center speaker

4 / 5 Surround speaker (L/R)

6 / 7 Surround back speaker (L/R)

E / R Front presence speaker (L/R)

1)

9 Subwoofer

2)

1)

For 7.1.2-channel system

2)

Up to two subwoofers can be connected.

When connecting 6-ohm speakers

Set the unit’s speaker impedance to “6 Ω MIN”. For details, see “Setting the

speaker impedance” under “Connecting speakers” in the Owner’s Manual.

Precautions for connecting speaker cables

• Be sure that the unit and subwoofer are turned off.

• Prepare speaker cables in a place away from the unit, to avoid accidentally

dropping wire strands into the unit's interior which could result in a short

circuit or malfunction of the unit.

• Improper connection of speaker cables could cause a short circuit resulting

in damage to, or malfunctioning of, the unit or speakers.

– Carefully remove approximately 10 mm

(3/8") of insulation from the speaker-

connection ends of the cables, and twist

the bare wires of each speaker cable

together firmly.

– Do not allow the bare wires of separate speaker

cables to come into contact with one another.

– Do not allow speaker cable bare wires to come into

contact with metal parts on the unit (rear panel and

screws).

If “Check SP Wires” is shown on the front display when the unit is turned on,

turn off the unit and be sure that speaker cables have not caused a short

circuit.

1)

2)

RE

3

1

2

9

54

76

10° to 30° 10° to 30°

0.5 to 1 m

(1.6 to 3.3 ft)

0.5 to 1 m

(1.6 to 3.3 ft)

1.8 m

(5.9 ft)

1.8 m

(5.9 ft)

0.3 m (1 ft)

or more

10 mm

(3/8")

12 En

R L R L

R

L

R

L

4321

R

5

6

L R RL L

B

A

R

L

1

2

R L

PRE OUT

(REAR)

SUBWOOFER

TNORFRETNECFRONT

SURROUND SUR. BACK

(FRONT)

CENTER FRONT

R L R L

ZONE 2/ZONE 3/BI-AMP

F.PRESENCE

EXTRA SP1

SPEAKERS

SURROUND BACK

SURROUND

R.PRESENCE

R L R RL L

ZONE 2/ZONE 3/F.PRESENCE

EXTRA SP2

INPUT

2

34

1

Subwoofer

9

2

Front speaker (R)

10 mm

(3/8")

1

Front speaker (L)

3

Center speaker

Surround speaker (R)

5

Surround speaker (L)

4

Audio pin cable

R

Front presence speaker (R)

E

Front presence speaker (L)

For 7.1.2-channel system

Surround back speaker (R)

7

Surround back speaker (L)

6

• Use a subwoofer equipped

with built-in amplifier.

• Up to two subwoofers can

be connected.

En 13

3

Connecting external devices

R L R L

R

L

R

L

4321

R

5

6

L R RL L

B

A

R

L

HDMI

ARC

HDMI HDMI

HDMI OUT

ARC

1

2

HDMI

(1 MOVIE) (5 STB) (6 GAME)

AV 1 AV 2 AV 3 AV 4

(HDCP2.2)

AV 5 AV 6 AV 7

(HDCP2.2)

3

HDMI OUT

(HDCP2.2)

(ZONE OUT)

HDMI HDMI HDMI

HDMI

TV BD/DVD player Satellite/cable set top box

HDMI input

HDMI output HDMI output

Playback devices are best connected to the input jack with the

label that most closely describes the type of device. For more

information, see “SCENE function” (p. 24).

14 En

4

Connecting the radio antennas

FM/AM antennas

(Except for Australia model)

DAB/FM antenna

(Australia model)

R L R L

R

L

R L

4321

R

5

6

L R RL L

B

A

R

L

FM antenna (supplied) AM antenna (supplied)

Hold down Insert Release

Assembling the AM antenna

Place the AM

antenna on a

flat surface.

Fix the end of the

FM antenna to a

wall.

R L R L

R

L

R L

4321

R

5

6

L R RL L

B

A

R

L

DAB/FM antenna (supplied)

Fix the antenna

ends to a wall.

En 15

5

Preparing a network connection

Prepare a wired or wireless network connection in accordance with your network environment.

Note

The wireless antenna must be raised if the unit will be connected to a Bluetooth device.

R L R L

R

L

R

L

4321

R

5

6

L R RL L

B

A

R

L

NETWORK

(4

NET

)

(8 SERVER)

LAN

Raise the wireless antenna so that it is standing up straight.

(Procedures for connecting the unit to a wireless router are described

in step

8

.)

Notice

Do not apply excessive force on the antenna. Doing so may damage it.

Wireless network connection

Internet

Network cable

Router Modem

Wired network connection

16 En

6

Connecting the power cable to an AC wall outlet,

and turning on the unit

1 Plug the power cable into an

AC wall outlet.

2 Press z (receiver power) to

turn on the unit.

3 Turn on the TV and switch the

TV input to display video from

the unit (HDMI OUT jack).

The Network Setup screen shown below will be

displayed on the TV when the unit is turned on for

the first time after purchase. It may take several

tens of seconds for the screen to be displayed

(WAC: Wireless Accessory Configuration).

See “Sharing the iOS device setting” under

“Connecting to a network wirelessly” in the

Owner’s Manual when using this function to

connect the unit to a network.

This document explains wireless connection

using the MusicCast CONTROLLER app

installed on your mobile device. Follow the

procedure described under “8 Setting MusicCast”

(p. 19).

Note

This screen will not be displayed if the unit is connected

to a router via its NETWORK jack (wired connection).

R L R L

R

L

R

L

4321

R

5

6

L R RL L

B

A

R

L

AC IN

To an AC wall

outlet

INPUT

PURE DIRECT

SCENE

4321

8765

HDMI OUT

PARTY

SLEEP

I

NPUT

P

URE DIRE

C

T

SC

ENE

4

3

2

1

8

7

6

5

HDMI OUT

PARTY

S

LEEP

INPUT

PURE DIRECT

SCENE

4321

8765

HDMI OUT

PARTY

SLEEP

MAIN 2 3 4

ZONE

I

N

P

U

T

P

PU

R

E

D

E D

IR

C

EC

T

S

C

ENE

4

3

2

1

8

7

6

5

HD

M

I

O

U

T

P

A

P

PPP

R

T

Y

T

TT

S

L

E

P

MAI

N

23

4

Z

ON

E

z

En 17

7

Optimizing the speaker settings automatically

(YPAO)

The Yamaha Parametric room Acoustic Optimizer (YPAO) function detects speaker connections, measures the distances from them to your listening position(s),

and then automatically optimizes the speaker settings, such as volume balance and acoustic parameters, to suit your room.

YPAO MIC

12

3

9

54

ER

BAND TUNINGTUNING

MEMORY

RED GREEN

YELLOW

BLUE

POP-UP

/MENU

HOME

TOP

MENU

VOLUME

PROGRAM

SUR. DECODE

STRAIGHT

B

AND

TU

NIN

G

T

U

NIN

G

M

EM

O

R

Y

RED

GREEN

YELLOW

BLUE

PO

P-UP

/MENU

/

HOME

TO

P

MENU

VO

L

U

ME

P

R

OG

RAM

S

UR. DE

CO

DE

S

TRAIGHT

BANDBAND TUNINGTUNING TUNINGTUNING

MEMORYMEMORY

RED GREEN

YELLOW

BLUE

POP-UP

/MENU

HOME

TOP

MENU

VOLUME

PROGRAM

SUR. DECODE

STRAIGHT

AI

ENHANCER

BAND

BANDBANDBAND

B

BAND

BANDBANDBAND

T

TUNING

UG

TUNING

UGUGUGUGUGUG

UG

UGUGUG

TUNING

TUNINGTUNINGTUNING

UG

UGUGUGUGUGUG

UG

UGUGUG

TUNING

TUNINGTUNINGTUNING

O

OOO

MEMORY

MEMO

M

EM

O

R

Y

MEMORYMEMORYMEMORY

R

E

D

G

R

E

N

Y

E

L

O

W

B

L

U

E

PO

P-

U

P

/MENU

//

H

O

M

E

T

O

P

MENU

V

O

L

U

M

E

P

OG

ROG

R

A

RA

M

SCOSUR DECODE

SUR. DECODE

S

UR. DE

CO

DE

SUR. DECODE

S

TRAI

G

HT

A

I

ENHAN

C

E

R

ENTER

RETURN

Note the following regarding

YPAO measurement

• Test tones are output at high

volume and may surprise or

frighten small children.

• Test tone volume cannot be

adjusted.

• Keep the room as quiet as

possible.

• Stay in a corner of the room

behind the listening position

so that you do not become an

obstacle between speakers

and the YPAO microphone.

• Do not connect headphones.

Ear height

Listening position

YPAO microphone

Cursor keys

18 En

1 Turn on the subwoofer and set the volume to half.

If the crossover frequency is adjustable, set it to maximum.

2 Place the YPAO microphone at your listening

position and connect it to the YPAO MIC jack on

the front panel.

The screen below appears on the TV.

Note

Place the YPAO microphone at your listening position (same height as your ears).

We recommend the use of a tripod as a microphone stand. You can use the tripod

screws to stabilize the microphone.

3 Use the cursor keys to select “Start” and press

ENTER.

The measurement will start in 10 seconds.

It takes about 5 minutes to measure.

The screen below appears on the TV when the measurement finishes.

Note

If an error message (such as ERROR 1) or warning message (such as

WARNING 2) appears, see “Optimizing the speaker settings automatically

(YPAO)” in the Owner’s Manual.

4 Select “Measurement result” and press ENTER to

display the result.

After confirming the result, press RETURN to return to the “Measurement

Finished” screen.

5 Use the cursor keys to select “Save” and press

ENTER.

6 Disconnect the YPAO microphone from the unit.

This completes optimization of the speaker settings.

VOLUME

CROSSOVER/

HIGH CUT

MIN MAX

En 19

8

Setting MusicCast

What is MusicCast

MusicCast is a brand new wireless musical solution from Yamaha, allowing

you to share music among all of your rooms with a variety of devices. You can

enjoy music from your smartphone, PC, NAS drive and music streaming

service anywhere in your house with one easy-to-use app. For more details

and a lineup of MusicCast compatible products, refer to the following site:

http://www.yamaha.com/musiccast/

• Seamlessly control all MusicCast compatible devices with the dedicated

app “MusicCast CONTROLLER”.

• Play back music from music streaming services. (The compatible music

streaming services may differ depending on your region and product.)

• Configure wireless network settings of MusicCast compatible devices.

Note

See the Owner’s Manual for information on other wireless connection methods if the

MusicCast CONTROLLER app will not be used.

Using MusicCast CONTROLLER

To use the network features on the MusicCast compatible device, you need

the dedicated app “MusicCast CONTROLLER” for the operation. Search for

the free app “MusicCast CONTROLLER” on the App Store or Google Play

and install it to your device.

Adding the unit to the MusicCast

network

Perform the following procedure to add the unit to the MusicCast network.

You can also configure the unit’s wireless network settings at once.

Note

The SSID and security key for your network will be needed.

1 Tap the “MusicCast CONTROLLER” app on

your mobile device and tap “Setup”.

Note

If you have already connected other MusicCast compatible devices to the network,

tap “Settings” and then “Add New Device”.

2 Follow the app’s on-screen instructions.

20 En

3 Press and hold the CONNECT button on the front

panel of the unit for 5 seconds, as instructed by

the app.

4 Follow the app’s on-screen instructions to

configure network settings.

When a connection has been established, “Completed” will be displayed

in the front display of the unit.

Network connection with the MusicCast CONTROLLER app is now complete,

and the unit has been registered as a MusicCast-enabled device.

PHONES

SILENT CINEMA

AI

THGIARTS

PROGRAM

MULTI ZONE

XUA

ZONE 2

ZONE 3

ZONE 4

ZONE CONTROL

SCENE

1234

RL AUDIO

INFO

(

WPS

)

MEMORY

FM AM

TUNING

PRESET

VOLUME

(

CONNECT

)

ページが読み込まれています...

Yamaha RX-V2085 クイックスタートガイド

このマニュアルも適しています

Yamaha RX-V2085 クイックスタートガイド

他の言語で

関連論文

その他のドキュメント