©2003 Sony Corporation Printed in Korea
MV-101
3-255-987-42 (1)
Installation/Connections
32
1
5
× 4
1
7
DVD Player
× 2 × 4
Overhead monitor XVM-R70 (not supplied)
DVD player MV-101
Mounting example
Equipment used in illustrations (not supplied)
There is an R (audio right )/L (audio left)/V (video) output on MV-101, so you can connect either
XVM-R70 or XVM-H65.
Headrest monitor XVM-H65
Overhead monitor XVM-R70
Headrest monitor XVM-H65 (not supplied)
5.3 m 3 m
4
8
2.5 m
6
2
REMOTE SIGNAL INPUT
RL
OUTPUT OPTICAL OUTPUT POWER 12V
V
Optical cable (not supplied)
7*
2
1
2
3
5
Caution
•This unit is designed for negative earth 12 V
DC operation only.
•Before making connections, turn the car
ignition off to avoid short circuits.
•Connect the yellow and red power input leads
only after all other leads have been connected.
•Be sure to connect the red power input lead to
the positive 12 V power terminal which is
powered when the ignition switch is in the
accessory position.
•Run all earth wires to a common earth
point.
• Use of controls adjustments or performance of
procedures of other than those specified herein
may result in hazardous radiation exposure.
Notes on the power supply cord (yellow)
•When connecting the player in combination
with other stereo components, the connected
car circuit’s rating must be higher than the
sum of each component’s fuse.
•When no car circuits are rated high enough,
connect the unit directly to the battery.
Notes on installation
•Before installation, be sure to turn the ignition
switch to the OFF position or take the key out.
Installing the player and the monitor (not
supplied) with the ignition on may cause
battery drain or a short circuit.
•Do not damage any pipes, tubes, the fuel tank
or electric wiring when installing the player
and the monitor (not supplied). This can cause
a fire. If you drill a hole in car panels, make
sure that any hidden car parts will not be
damaged.
•Do not use any nuts or bolts for safety devices
such as steering linkage, fuel supply or
braking systems. This can cause a fire or an
accident.
•Take care to prevent cords and wires from
getting tangled or crimped in the moving
portion of a seat rail.
Parts list (1)
The numbers in the list are keyed to those in the
instructions.
Cautions
•The screws attached to both sides of the player
are necessary only when transporting the
player. Before installing the player, be sure to
take out all of the screws (left side: 2 and right
side: 2, so total 4 screws).
•The 4 screws work to mechanically support the
player during transportation, so keep the
screws for future transportation, such as
relocation, etc.
Connection diagram (2)
1 to a metal surface on the car
First connect the black earth lead, then connect
the yellow and red power input leads.
2 to the +12 V power terminal which is
energized at all times
Be sure to connect the black earth lead to a
metal surface of the car first.
3 to the +12 V power terminal which is
energized when the ignition switch is in
the accessory position
Be sure to connect the black earth lead to a
metal surface of the car first.
Remote control sensor
Monitor cable (supplied with XVM-R70)
R/L/V
OUT
REMOTE SIGNAL INPUT
OPTICAL OUTPUT
*
1
Remote signal cord with stereo mini jacks: (5m)
(supplied with a Sony monitor)
Connects the player MV-101 and a connection box of an
optional Sony monitor.
(However, this connection is not available for XVM-R75)
*
2
Remote control sensor 7 and its extension cord 8
(supplied with MV-101)
Connect the remote control sensor
7 and its extension
cord
8 to the player MV-101 when XVM-R75, XVM-H6,
or an optional monitor other than Sony product is
connected.
*
3
There is an R (audio right )/L (audio left)/V (video)
output on MV-101, so you can connect either XVM-R70
or XVM-H65.
*
1
1 m
5A
1A
XVM-R70
XVM-H65
5 m
Connection box XA-115
(supplied with XVM-R70)
Connection box XA-113
(supplied with XVM-H65)
to AV output
to AV input
6
POWER 12V
to AV input
to AV output
Monitor cable (supplied with XVM-H65)
*
3
*
3
black/
black/
1 m
5 m
yellow/
red/
•
•
•
•
•
•
•
•
•
•
•
•
1
•
•
2
1
2
3
*
1
*
2
7 8
7 8
*
3
8*
2
To optical input
3
1
2
3
1
2
3
1
2
3
2
3
ø 3 mm
4
15º
Remote control sensor
Light sensor
Wireless remote commander
Light sensor
Almost 3 m
15º
c
A Horizontal installation B Vertical installation
4
ø
3 mm
Precautions
•Choose the mounting location carefully.
•Avoid installing the player in places:
— subject to temperatures below – 30 °C or
above 45 °C.
— subject to direct sunlight.
— subject to heat;
Keep all products away from nearby hot
vehicle components that heat up over time
such as hoses, high current wires, and
braking system components. Make sure to
leave enough room for ventilation of
openings and slots to protect from over
heating.
— near heat sources such as heaters.
— exposed to rain or moisture.
— exposed to excessive dust or dirt.
— subject to excessive vibration.
— where the fuel tank might be damaged by
the tapping screws.
—where wire harnesses or pipes might be
under the place.
— where the screws or the player itself might
damage the spare tire, tools, or other
equipment in or under the trunk.
— where the player might interfere with the
normal movements of the driver.
— under the floor carpet, as the heat
dissipation from the player might damage
the carpet.
•Be sure to use only the supplied mounting
hardware for a safe and secure installation.
•Use only the supplied screws.
•Make holes of ø 3 mm only after making sure
there is nothing on the other side of the
mounting surface.
•Do not install the player on inclined places.
Install the player on a level surface.
•Install the player just horizontally or vertically.
How to install the player (3)
When installing the player, choose the mounting
location carefully.
1 Place the player where you plan to install
it.
2 Mark the 4 positions for the holes of the
screws 3 on the surface of the mounting
board (not supplied).
The supplied mounting screws
3
are 15 mm
long, so make sure that the mounting board is
thicker than 15 mm.
3 Drill the 4 positions to make the holes of
ø 3 mm in diameter.
4 Mount the player on the board (not
supplied) with the parts 1 and mounting
screws of 2 and 3.
Remote control sensor (4)
Before installing the remote control sensor,
make sure the maximum signal distance of
remote control. The remote control can be used
up to approximately 3 m from the light sensor,
in a conical area spreading roughly 15º from the
light sensor.
For your safety
After installing the remote control sensor, be
sure to use the cord cramp (not supplied) to
secure up the cord onto the passenger seat side,
as it may interfere with the normal driving
operation. It is very dangerous for the cord to
get tangled with the gearshift lever during
driving.
Warning when installing in a car
without ACC (accessory)
position on the ignition key
switch
After turning off the ignition, be sure to
press and hold the POWER button on the
card remote commandar for more than 2
seconds. Make sure that the green light of
the POWER button on the player is turned
off.
Otherwise, the player is not turned off and this
causes battery drain.
RESET button
When the installation and connections are
completed, be sure to open the front panel, then
press the RESET button with a ballpoint pen, etc.
•
•
— °C °C
—
—
—
—
—
—
—
—
—
—
—
•
•
•
ø
•
•
3
1
2 3
3
3 ø
4 1 2 3
4
-
1
-
2
-
3
-
4
