Operating Instructions
(Household) AC/Rechargeable Shaver
Model No. ES-LT6A
ES-LT2A
English ��������������������������������������������� 3
中文 ������������������������������������������������ 19
한글 ������������������������������������������������ 33
ES-LT6A_2A_ASIA.indb 1 2015/04/20 15:03:43
2
ES-LT6A_2A_ASIA.indb 2 2015/04/20 15:03:43
3
English
Thank you for purchasing this Panasonic product.
Before operating this unit, please read these instructions completely and save them for future use.
Safety precautions..................... 4
Intended use ����������������������������������������7
Parts identication ������������������������������8
Operation and display of the switch
lock �������������������������������������������������������9
Charging the shaver �������������������������� 10
Using the shaver�������������������������������� 11
Cleaning the shaver ��������������������������14
Troubleshooting ��������������������������������16
Battery life ������������������������������������������18
Removing the built-in rechargeable
battery�������������������������������������������������18
Specications ������������������������������������18
Contents
Operating Instructions
(Household) AC/Rechargeable Shaver
Model No. ES-LT6A
ES-LT2A
ES-LT6A_2A_ASIA.indb 3 2015/04/20 15:03:43
4
English
Safety precautions
To reduce the risk of injury, loss of life, electric shock, fire, and
damage to property, always observe the following safety precautions.
Explanation of symbols
The following symbols are used to classify and describe the level
of hazard, injury, and property damage caused when the
denotation is disregarded and improper use is performed.
DANGER Denotes a potential
hazard that will result in
serious injury or death.
WARNING Denotes a potential
hazard that could result
in serious injury or death.
CAUTION
Denotes a hazard that
could result in minor injury.
The following symbols are used to classify and describe the type
of instructions to be observed.
This symbol is used to alert users to a specific operating
procedure that must not be performed.
This symbol is used to alert users to a specific operating
procedure that must be followed in order to operate the
unit safely.
WARNING
►Power supply
Do not connect or disconnect the adaptor to a
household outlet with a wet hand.
- Doing so may cause electric shock or injury.
Do not immerse the AC adaptor and the charging
stand in water or wash with water.
Do not place the AC adaptor and the charging stand
over or near water filled sink or bathtub.
Never use the appliance if the AC adaptor is damaged
or if the power plug fits loosely in a household outlet.
Do not damage, modify, or forcibly bend, pull, or
twist the cord.
Also, do not place anything heavy on or pinch the
cord.
-
Doing so may cause electric shock or fire due to a short circuit.
Do not use in a way exceeding the rating of the
household outlet or the wiring.
- Exceeding the rating by connecting too many plugs to one
household outlet may cause fire due to overheating.
Do not use anything other than the supplied AC
adaptor and the charging stand. Also, do not charge
any other product with the supplied AC adaptor and
the charging stand.
- Doing so may cause burn or fire due to a short circuit.
Always ensure the appliance is operated on an
electric power source matched to the rated voltage
indicated on the AC adaptor.
Fully insert the adaptor.
- Failure to do so may cause fire or electric shock.
ES-LT6A_2A_ASIA.indb 4 2015/04/20 15:03:44
5
English
WARNING
►In case of an abnormality or malfunction
Immediately stop using and remove the adaptor if
there is an abnormality or malfunction.
- Failure to do so may cause fire, electric shock, or injury.
<Abnormality or malfunction cases>
•The main unit, charging stand, adaptor or cord is
deformed or abnormally hot.
•The main unit, charging stand, adaptor or cord
smells of burning.
•There is abnormal sound during use or charging of
the main unit, charging stand, adaptor or cord.
- Immediately request inspection or repair at an authorized
service center.
►This product
This shaver has a built-in rechargeable battery. Do
not throw into fire, apply heat, or charge, use, or
leave in a high temperature environment.
- Doing so may cause overheating, ignition, or explosion.
Do not modify or repair.
- Doing so may cause fire, electric shock, or injury.
Contact an authorized service center for repair (battery
change etc).
Never disassemble except when disposing of the
product.
- Doing so may cause fire, electric shock, or injury.
►Cleaning
Disconnect the AC adaptor when cleaning the
shaver with water.
- Failure to do so may cause electric shock or injury.
Always unplug the adaptor from a household outlet
when cleaning.
- Failure to do so may cause electric shock or injury.
Regularly clean the power plug, the appliance plug
and the charging plug to prevent dust from
accumulating.
- Failure to do so may cause fire due to insulation failure
caused by humidity.
Disconnect the adaptor and wipe with a dry cloth.
This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given
supervision or instruction concerning use of the
appliance by a person responsible for their safety.
Children should be supervised to ensure that they
do not play with the appliance.
- Failure to do so may cause an accident or injury.
The supply cord cannot be replaced. If the cord is
damaged, the AC adaptor should be scrapped.
- Failure to do so may cause an accident or injury.
►Preventing accidents
Do not store within reach of children or infants. Do
not let them use it.
- Putting the inner blades, the cleaning brush and/or the oil
container in the mouth may cause accidents and injury.
ES-LT6A_2A_ASIA.indb 5 2015/04/20 15:03:44
6
English
WARNING
If oil is consumed accidentally, do not induce
vomiting, drink a large amount of water and contact
a physician.
If oil comes into contact with eyes, wash
immediately and thoroughly with running water and
contact a physician.
- Failure to follow these instructions may result in physical
problems.
CAUTION
►Protecting the skin
Do not use excessive pressure to apply the system
outer foil to your lip or other part of your face. Do
not apply the system outer foil directly to blemishes
or injured skin.
- Doing so may cause injury to the skin.
Do not forcefully press the system outer foil. Also,
do not touch the system outer foil with fingers or
nails when in use.
Do not use this product for hair on head or any
other part of the body.
- Doing so may cause injury to skin or reduce the life of the
system outer foil.
Do not touch the blade section (metallic section) of
the inner blade.
- Doing so may cause injury to your hands.
Check the system outer foil for cracks or
deformations before use.
- Failure to do so may cause injury to the skin.
Be sure to place the protective cap on the shaver
when carrying around or storing.
- Failure to do so may cause injury to skin or reduce the life
of the system outer foil.
►Note the following precautions
Do not allow pins or trash to adhere to the power
plug, the appliance plug or the charging plug.
- Doing so may cause electric shock or fire due to a short
circuit.
Do not share your shaver with your family or other
people.
- Doing so may result in infection or inflammation.
Do not drop or hit against other objects.
- Doing so may cause injury.
Do not wrap the cord around the adaptor when storing.
- Doing so may cause the wire in the cord to break with the
load, and may cause fire due to a short circuit.
Disconnect the adaptor from the household outlet
when not using.
- Failure to do so may cause electric shock or fire due to
electrical leakage resulting from insulation deterioration.
Disconnect the adaptor or the appliance plug by
holding onto the adaptor or the appliance plug
instead of the cord.
- Failure to do so may cause electric shock or injury.
ES-LT6A_2A_ASIA.indb 6 2015/04/20 15:03:44
7
English
►Disposing of the rechargeable battery
DANGER
The rechargeable battery is exclusively for use with
this shaver. Do not use the battery with other products.
Do not charge the battery after it has been removed
from the product.
•Do not throw into fire or apply heat.
•Do not hit, disassemble, modify, or puncture with a nail.
•Do not let the positive and negative terminals of
the battery get in contact with each other through
metallic objects.
•Do not carry or store the battery together with
metallic jewelry such as necklaces and hairpins.
•Do not charge, use, or leave the battery where it
will be exposed to high temperatures, such as
under direct sunlight or near other sources of heat.
•Never peel off the tube.
- Doing so may cause overheating, ignition, or explosion.
WARNING
After removing the rechargeable battery, do not
keep it within reach of children and infants.
- The battery will harm the body if accidentally swallowed.
If this happens, consult a physician immediately.
If the battery fluid leaks out, take the following
procedures. Do not touch the battery with your bare
hands.
- The battery fluid may cause blindness if it comes in
contact with your eyes.
Do not rub your eyes. Wash immediately with clean water
and consult a physician.
-
The battery fluid may cause inflammation or injury if it comes in
contact with the skin or clothes.
Wash it off thoroughly with clean water and consult a physician.
Intended use
•Do not bring the system outer foil into contact with hard object.
Doing so may damage the blades as they are very thin and
deform easily.
•Do not dry the main unit with a dryer or a fan heater.
Doing so may cause malfunction or deformation of the parts.
•Do not leave the shaver exposed to direct sunlight with the foil
frame detached.
Doing so may deteriorate the waterproof rubber and degrade
waterproof function, which may cause to malfunction.
•Store the shaver in a place with low humidity after use.
Failure to do so may cause malfunction due to condensation or rust.
•Keep both the inner blades inserted. If only one of the inner
blades is inserted, the shaver may be damaged.
•If you clean the shaver with water, do not use salt water or hot
water. Do not soak the shaver in water for a long period of time.
ES-LT6A_2A_ASIA.indb 7 2015/04/20 15:03:44
8
English
System outer foil release
buttons
Inner blades
Trimmer
Trimmer handle
Main body rear terminals
AC adaptor (RE7-87)
(The shape of the AC
adaptor differs depending
on the area.)
Adaptor
Power plug
Cord
Appliance plug
Accessories
Travel pouch
Cleaning brush
Oil
Charging stand ES-LT6A
Charging plug
Parts identification
a
c
b
d
ES-LT6A ES-LT2A
Front Back
ES-LT6A
Main body
Protective cap
System outer foil
Foil frame
Foil frame release buttons
Finger rest
Power switch
To turn the shaver on and
off and also lock and
unlock the power switch.
Lamp display
a. Shaving sensor lamp
()
b. Battery capacity lamp
c. Switch lock lamp ( )
d. Charge status lamp
()
Appliance socket
Outer foil section
ES-LT6A_2A_ASIA.indb 8 2015/04/20 15:03:44
9
English
Operation and display of the switch lock
►Locking the power switch
1. Press the power
switch once and
then release.
•The shaver
starts operating.
2. Press the power
switch for more
than 2 seconds
when the shaver
is operating.
•The shaver will
stop operating.
3. Release the
power switch.
The switch lock
lamp is off.
The switch lock
lamp will light up.
The switch lock
lamp will turn off
after 5 seconds.
►Unlocking the power switch
1. Press the power switch for
more than 2 seconds.
2. Once the shaver starts
operating, release the power
switch.
The switch lock lamp will blink. The switch lock lamp will turn
off.
►Checking the power switch is locked
Press the power switch while it is locked.
The switch lock lamp will blink and then turn off after 5 seconds.
•You can also check this by unplugging the AC adaptor while
charging.
ES-LT6A_2A_ASIA.indb 9 2015/04/20 15:03:45
10
English
Charging the shaver
1
1Insert the appliance plug into
the shaver.
•Turn the shaver off before inserting.
2
2Plug in the adaptor into a
household outlet.
•Wipe off any water droplets on the
appliance socket.
•Check that the charge status lamp ( )
glows.
1
2
•Charging is completed after approx. 1 hour.
The charging time may differ with the charging capacity.
•Charging the appliance after each use will not affect the battery life.
3
3
Disconnect the adaptor after charging is completed.
•Charging the battery for more than 1 hour will not affect
battery performance.
While charging
ES-LT6A ES-LT2A
The charge status lamp ( )
glows.
The number of the battery
capacity lamp will increase as
charging progresses.
The charge status lamp ( )
glows.
After charging is completed
ES-LT6A ES-LT2A
The battery capacity lamp and
the charge status lamp ( ) will
light up and then turn off after
5 seconds.
The charge status lamp ( )
turns off.
Abnormal charging
ES-LT6A ES-LT2A
The charge status lamp ( ) will blink twice every second.
•Recommended ambient temperature for charging is 10 – 35 °C.
It may take longer to charge or the battery may fail to charge
properly in extremely high or low temperatures.
Charge the shaver within the recommended ambient temperature
range.
•When charging the shaver for the first time or when it has not
been in use for more than 6 months, the charging time may
change or the charge status lamp ( ) may not glow for a few
minutes. It will eventually glow if kept connected.
•If there is noise from radio or other source while using the
shaver, move to a different location to use the shaver.
ES-LT6A_2A_ASIA.indb 10 2015/04/20 15:03:45
11
English
Charging with the charging stand ES-LT6A
1. Insert the appliance plug into the
charging stand.
2. Place the shaver on the charging stand.
3. Plug in the adaptor into a household
outlet.
2
3
1
Using the shaver
1
1Press the power switch.
•The power cannot be turned on when the switch lock lamp
( ) blinks, as the power switch is locked.
Press the power switch for more than 2 seconds to unlock.
(See page 9.)
2
2Hold the shaver as illustrated.
3
3Shave by slowly gliding the shaver over your
face against the grain of the beard.
•Start shaving by applying gentle pressure to your face.
Stretch your skin with your free hand and move the shaver
back and forth in the direction of your beard. You may gently
increase the amount of pressure as your skin becomes
accustomed to this shaver. Applying excessive pressure
does not provide a closer shave.
►Notes
•If you press the power switch for more than 2 seconds, the sonic
vibration cleaning mode is activated. (See page 14.)
You cannot shave in this mode.
•Do not place your fingers on the power switch while using the
shaver. This may cause the shaver to lock the power switch or
turn off. Place your fingers on the finger rest while using the
shaver.
•The appliance may not operate in an ambient temperature
approximately 5 °C or lower.
•Depending on the beard thickness or the amount of beard
trimmings in the shaver head, the shaving sensor may not react
and the driving sound may not change. This is not abnormal.
•The shaving sensor may not respond when the remaining battery
capacity is low. If this happens, recharge the shaver.
•Avoid the following situations to prevent damaging the system
outer foil. Applying pressure to any part of the system outer foil or
bringing the system outer foil into contact with hard object may
cause damage on the system outer foil.
- Shaving with only a part of the system outer foil.
- Finger or nail coming into contact with the system outer foil.
ES-LT6A_2A_ASIA.indb 11 2015/04/20 15:03:45
12
English
►Cord shaving
If you insert the appliance plug to the shaver and plug in the
adaptor into a household outlet, you can use it even if the battery
capacity is low.
•If the shaver does not work, continue charging it for approx.
1 minute.
•The battery will be discharged even when using the shaver with
the AC adaptor.
►Switching the shaver head
You can change the pivot action.
FREE
You can move the shaver head.
LOCK
You can lock the shaver head.
►Using the trimmer
Slide the trimmer handle up to the “ ”
position so that the trimmer stands upright.
Press and hold the lock release
button () and slide the trimmer
handle down to lower the trimmer.
Trimming sideburns
Slide the trimmer handle up. Turn the shaver
on and place at a right angle to your skin and
move downwards to trim your sideburns.
Pre-shave
The trimmer can be used for a
pre-shave of long beards.
Shave your beard with the
shaver head after the pre-shave.
ES-LT6A_2A_ASIA.indb 12 2015/04/20 15:03:45
13
English
Reading lamps when using
While using
ES-LT6A ES-LT2A
Approximate amount of battery
capacity is displayed as
20 - 100.
•It will turn off approximately
5 seconds after operating the
power switch.
•The shaving sensor lamp ( )
glows.
•The charge status lamp ( )
glows when using cord
shaving.
•The shaving sensor lamp ( )
glows.
•The charge status lamp ( )
glows when using cord
shaving.
When the battery capacity is low
ES-LT6A ES-LT2A
“20” blinks when operating the
shaver.
•You can shave 2 to 3 times
after “20” blinks. (This will
differ depending on usage.)
The battery capacity lamp ( )
blinks when operating the shaver.
•You can shave 2 to 3 times
after the battery capacity
lamp ( ) blinks. (This will
differ depending on usage.)
•The shaver can be used for approximately 2 weeks with a full
charge.
(Based on one 3-minute shave use per day until the battery is
exhausted)
•The number of usable days varies depending on the following
conditions.
- Beard thickness
- Pressure applied to the skin
- Ambient temperature
- Usage frequency of the sonic vibration cleaning mode
ES-LT6A_2A_ASIA.indb 13 2015/04/20 15:03:45
14
English
Cleaning the shaver
Do not use kitchen, bathroom, or toilet detergents. Also, do not
wipe with thinners, benzine, alcohol etc.
Doing so may result in malfunction.
1. Turn the power switch OFF, and disconnect the AC adaptor.
•Unlock the switch lock.
2. Apply some hand soap and some water to the system outer foil.
3. Press the power switch for more
than 2 seconds to activate the
sonic vibration cleaning mode.
•The battery capacity lamps
blink in order. ES-LT6A
•The battery capacity lamp ( )
and the charge status lamp
( ) blink alternately.
ES-LT2A
ES-LT6A ES-LT2A
•After about 20 seconds, it will be automatically turned off.
4. Remove the outer foil section and press
the power switch for more than
2 seconds to activate the sonic vibration
cleaning mode.
5. Clean the shaver, the outer foil section,
and the trimmer with running water.
•After rinsing with water, shake the
shaver up and down for a few times to
remove excess moisture.
Hitting the vanity, etc., while shaking
the shaver may cause malfunction.
•Splashing is reduced by rinsing the shaver in sonic vibration
cleaning mode.
6. Wipe off any drops of water with a dry cloth.
7. Dry the outer foil section, the shaver, and
the trimmer completely.
8. Attach the outer foil section to the shaver.
9. Lubricate the shaver.
The mark on the left means suitable for cleaning
under an open water tap.
Warning
Disconnect the cord from the shaver before cleaning it in
water to prevent electric shock.
Lubrication
To maintain shaving comfort for a long time, it is recommended
that the oil provided with the shaver is used.
1. Switch off the shaver.
2. Apply one drop of oil to each of the
system outer foil.
3. Raise the trimmer and apply a drop
of oil.
4. Switch the shaver on, and run it for
approximately five seconds.
5. Switch off the shaver, and wipe off any excess oil from the
system outer foil with a soft cloth.
ES-LT6A_2A_ASIA.indb 14 2015/04/20 15:03:46
15
English
Cleaning with the brush
►Cleaning with the long brush
Clean the system outer foil
(), the shaver body () and
the trimmer () using the
long brush.
►Cleaning with the short brush
Clean the inner blades using the short brush by
moving it in direction (A).
•Do not move the short brush in direction (B) as
it will damage the inner blades and affect their
sharpness.
•Do not use the short brush to clean the system
outer foil.
(A)
(B)
Replacing the system outer foil and the inner blades
system outer foil once every year
inner blades once every two years
►Removing the outer foil section
Press the foil frame release buttons and lift the
outer foil section upwards.
►Attaching the outer foil section
After turning the foil frame mark ( ) to the front,
securely attach the outer foil section to the shaver
until it clicks.
►Replacing the system outer foil
1. Press the system outer foil release buttons
and pull down the system outer foil.
2. Align the foil frame mark ( ) and the
system outer foil mark ( ) and securely
attach together until it clicks.
•The system outer foil cannot be reversely
attached.
•Always insert the system outer foil to the
foil frame when attaching to the shaver.
•Do not press the system outer foil
release buttons with excessive force.
Doing so may bend the system outer foil,
preventing complete attachment to the
foil frame.
►Replacing the inner blades
1. Remove the inner blades one at a time.
2. Insert the inner blades one at a time.
►Replacement parts
Replacement parts are available at your dealer or Service Center.
Replacement parts for
ES-LT6A/ES-LT2A
System outer foil WES9089
Inner blades WES9068
ES-LT6A_2A_ASIA.indb 15 2015/04/20 15:03:46
16
English
Troubleshooting
Perform the following actions.
If the problems still cannot be solved, contact the store where
you purchased the unit or a service center authorized by
Panasonic for repair.
Problem Action
The power switch does
not turn ON.
Unlock the switch lock.
(See page 9.)
Shavings fly out in all
directions.
This can be improved by cleaning
every time after shaving.
Clean the inner blades with the
brush when shavings are
adhering to the inner blades.
System outer foil gets hot.
Apply oil.
(See page 14.)
Replace the system outer foil if it
is damaged or deformed.
(See page 15.)
Operating time is short
even after charging.
Apply oil.
When the number of operations
per charge starts to decrease, the
battery is nearing the end of its life.
The odor is getting
stronger.
This can be improved by cleaning
every time after shaving.
The driving sound
changes while shaving.
While the shaving sensor lamp
glows, the shaving sensor is
operating. The sound changes
depending on the beard thickness.
Problem Action
You do not get as close a
shave as before.
This can be improved by cleaning
every time after shaving.
Replace the system outer foil and/
or inner blades.
Expected life of system outer foil
and inner blades:
System outer foil:
Approximately 1 year
Inner blades:
Approximately 2 years
Apply oil.
Shaver stopped
functioning even after
charging.
The appliance may not operate in
an ambient temperature
approximately 5 °C or lower.
The battery has reached the end
of its life.
Makes a loud sound.
Apply oil.
The shaver makes a high-pitched
sound due to the linear motor
drive. This does not indicate a
problem.
Confirm that the blades are
properly attached.
Clean the system outer foil with
the brush.
ES-LT6A_2A_ASIA.indb 16 2015/04/20 15:03:46
17
English
Problem Action
The shaving sensor does
not respond.
Depending on the beard thickness
or the amount of beard trimmings
in the shaver head, the shaving
sensor may not react and the
driving sound may not change.
This is not abnormal.
The shaving sensor may not
respond when the remaining
battery capacity is low. If this
happens, recharge the shaver.
Apply oil. The shaving sensor may
not respond when there is not
enough oil on the blades.
The shaving sensor
responds even though the
shaver is not in contact
with the skin.
Clean the beard trimmings from
the shaver.
When the shaver is extremely
dirty, remove the foil frame and
wash with water. (See page 14.)
Replace the system outer foil and/
or inner blades.
Expected life of system outer foil
and inner blades:
System outer foil:
Approximately 1 year
Inner blades:
Approximately 2 years
FAQ
Question Answer
Will the battery deteriorate
if not used for an
extended period of time?
The battery will deteriorate if not
used for over 6 months, so make
sure to perform a full charge at
least once every 6 months.
Can I charge the shaver
after every use?
The battery used is a lithium-ion,
so charging after every use will
have no effect on battery life.
What is the constituent of
the dedicated oil?
Constituent of the oil is liquid
paraffin.
ES-LT6A_2A_ASIA.indb 17 2015/04/20 15:03:46
18
English
Battery life
The life of the battery is 3 years. The battery in this shaver is not
intended to be replaced by consumers. Have the battery replaced
by an authorized service center.
Removing the built-in rechargeable battery
Remove the built-in rechargeable battery before disposing of
the shaver.
Please make sure that the battery is disposed of at an officially
designated location if there is one.
This figure must only be used when disposing of the shaver, and
must not be used to repair it. If you dismantle the shaver yourself,
it will no longer be waterproof, which may cause it to malfunction.
•Remove the shaver from the AC adaptor.
•Press the power switch to turn on the power and then keep the
power on until the battery is completely discharged.
•Perform steps to and lift the battery, and then remove it.
•Take care not to short circuit the positive and negative terminals
of the removed battery, and insulate the terminals by applying
tape to them.
For environmental protection and recycling of materials
This shaver contains a Lithium-ion battery.
Please make sure that the battery is disposed of at an officially
assigned location, if there is one in your country.
Specifications
Power source See the name plate on the AC adaptor.
(Automatic voltage conversion)
Motor voltage 3.6 V
Charging time Approx. 1 hour
This product is intended for household use only.
ES-LT6A_2A_ASIA.indb 18 2015/04/20 15:03:48
19
中文
感謝您購買本 Panasonic 產品。
使用本產品之前，請仔細閱讀本說明書，並妥善保存以供未來使用。
安全須知 ........................................................20
用途 ................................................................22
部件說明 ........................................................23
開關鎖定的操作與顯示 ..............................24
充電 ................................................................25
使用方法 ........................................................26
清洗 ................................................................28
疑難排解 ........................................................30
電池壽命 ........................................................31
拆除內置充電電池 .......................................31
規格 ................................................................32
目錄
使用說明書
（家用） 交流•充電式 刮鬍刀
型號 ES-LT6A
ES-LT2A
ES-LT6A_2A_ASIA.indb 19 2015/04/20 15:03:48
20
中文
安全須知
為減低受傷，死亡、觸電、火災及財物損失的風險，請務必遵照以
下安全預防措施。
符號說明
以下符號用於為危險、傷害及財物損失的級別分類和作出解釋。若
不理會此等符號，不當使用本產品就可能會導致所述的危險、人身
傷害及財物損失。
危險 表示潛在的危險會導致嚴重受傷或致命。
警告
表示潛在的危險可能會導致嚴重受傷或致命。
注意
表示危險可導致輕微受傷。
以下符號用於分類和解釋必須留意的指示類型。
此符號用於提示用戶，不得執行某項特定的操作程序。
此符號用於提示用戶，必須遵從某項特定的操作程序，藉
以安全操作本產品。
警告
►電源供應
切勿在手濕時將轉接器插入家用電源插座或從插座中拔除。
- 否則可導致觸電或受傷。
切勿將電源供應器和充電座浸在水中或用水洗滌。
切勿將電源供應器和充電座置於裝滿水的水槽、浴缸上
方或附近。
如電源供應器損壞，或電源插頭未緊接家用電源插座上，
切勿使用本產品。
切勿損壞、改裝或用力弄彎、拉址或纏繞電源線。
此外，切勿將重物放在電源線上或夾緊電源線。
- 否則可能會因短路而導致觸電或火警。
切勿以超出家用電源插座或配線額定值的方式使用產品。
- 將太多插頭插至同一插座上，以致超出額定值，可能會因
過熱而導致火警。
切勿使用非隨附的電源供應器和充電座。此外，切勿使用
隨產品附上的電源供應器和充電座為任何其他產品充電。
- 否則可能會因短路而導致灼傷或火警。
請務必使用與電源供應器上標示之額定電壓相符的電源
進行操作。
必須完全插入轉接器。
- 否則可導致火警或觸電。
ES-LT6A_2A_ASIA.indb 20 2015/04/20 15:03:48
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
/