StatementLinear
Mounting Instructions/安装说明书
SP800P
Signify (China) Investment Co., Ltd.
Building No. 9, Lane 888 Tianlin Road, Minhang District, Shanghai, China
Postalcode: 200233
昕诺飞（中国）投资有限公司
中国上海市闵行区田林路888弄9号楼
邮编：200233
Product Type
型号
Voltage (V)
电压
Frequency (Hz)
频率
Power (W)
功率
CCT
色温
Weight (Kg)
重量
SP800P LED21/840 L60W6 SD 220-240~ 50/60 17.5 4000K 2.62
SP800P LED21/840 L60W6 SD PSD 220-240~ 50/60 17.5 4000K 2.62
SP800P LED41/840 L120W6 SD 220-240~ 50/60 34.8 4000K 4.61
SP800P LED41/840 L120W6 SD PSD 220-240~ 50/60 34 4000K 4.61
SP800P LED52/840 L150W6 SD 220-240~ 50/60 46.5 4000K 5.66
SP800P LED52/840 L150W6 SD PSD 220-240~ 50/60 43 4000K 5.66
SP800P LED20/940 L60W6 SD PSD 220-240~ 50/60 17.5 4000K 2.62
SP800P LED38/940 L120W6 SD PSD 220-240~ 50/60 34 4000K 4.61
`
4441 702 64821
Philips and the Philips shield emblem are registered trademarks of Koninklijke Philips N.V.
Dimension 灯具尺寸
70
105
LL
70
105
L
Product Type/型号 L (长度)
SP800P L60 626
SP800P L120 1224
SP800P L150 1524
Installation 安装
D
D (吊绳间距 ):
L60: 602±3 mm
L120: 1201±3 mm
L150: 1500±3 mm
1
Arrange boxed luminaires on floor in
specified mounting locations. Remove
luminaires from boxes.
将盒装灯具放置在指定安装地的地面
上。将灯具从箱子中取出。
N OT E : I f c on d i t i o n s a r e d u s t y / d i r t y ,
recommended practice is to leave fixtures in
their plastic bag until ready to remove top cap
for wiring.
注意：如果现场安装环境灰尘比较多，
建议在准备好打开上盖接线时再将灯具
从包装袋中取出。
IMPORTANT!!!
AVOID HANDLING THE LIGHT GUIDES
WITHOUT WEARING CLEAN GLOVES.
请不要在未戴手套的情况下触摸导光板
建议在安装过程中全程佩戴手套
Prepare luminaires
准备灯具 2
x 2
Remove Top Cap
打开上盖
4Feed Wires into Luminaire
将电源线接入灯具
Feed wires into the luminaires on one end (both ends
for PSD version. One for power supply and the other
for signal supply.) of the luminaire.
将电缆线接入灯具的一端（PSD版本需要接两端，
一端进电源线另外一端进信号线）。
3Remove End Cap
卸下端盖
x 2
5Insert Aircraft Cable
穿入钢丝绳
2
1Release the cable gland
将格兰头拧松
Insert cable through gland nut
and pull out from lateral side
将电缆线穿过格兰头然后从
侧边拉出来
6Mount Aircraft Cable
安装钢丝绳
`
x 2
Screws not provided
螺丝不提供
Gripper should be mounted on ceiling
through screws
夹钳需要通过螺丝固定于天花板上
3Hold the stripped end and
insert the cable into luminaire
手持线缆剥线端并再次插入
灯具中
4Complete electrical connection
and tighten the gland nut.
完成电气连接然后拧紧格兰头
L : Brown;
N: Blue;
: Yellow+Green
DA/N : Gray
DA/Ls: White
PSD version only
仅限PSD版本
Please use a terminal box rated IP20 or above with dimension
no smaller than 20 x 20 x 40.
Please note that this is NOT provided.
请使用IP20及以上的接线盒（尺寸不小于20x20x40mm)，
本产品不提供接线盒。
Unit：mm
Connect power supply cable 连接电源线
Cable spec. 60227 IEC52/60245 IEC57 0.75~2.5 mm
( not provided), strip length: 8mm.
电线规格 60227 IEC52/60245 IEC57 0.75~2.5 mm
(不随灯具提供)，剥线长度: 8mm.
2
2
Cable spec. 60227 IEC52/60245 IEC57 0.75~2.5 mm
( not provided), strip length: 8mm.
电线规格 60227 IEC52/60245 IEC57 0.75~2.5 mm
(不随灯具提供)，剥线长度: 8mm.
2
2
Luminaire cable (not provided):
灯具电源线(不随灯具提供):
Luminaire cable (not provided):
灯具电源线(不随灯具提供):
50
38 8
6-8
3×0.75
50
38 8
6-8
3×0.75
PSD version only
仅限PSD版本
LL GG NN
LL
NNGG
DA+DA+DA-DA-
38 8
4-8
2×0.75
38 8
4-8
2×0.75
DA+DA+
38 8
4-8
2×0.75
DA+
DA/NDA/N
DA/LsDA/Ls
IMPORTANT!!!
The length of supply cable must be longer than
aircraft cable.
注意！！！
电缆线的长度必须要大于钢丝绳
10 Leveling and Cleanup
调整高度及清洁
• Level row by adjustments at the gripper.
• Wipe light guide panel clean if required – ensuring to not introduce scratches.
• 通过夹钳来调整灯具的水平高度
• 如有需要请将导光板擦拭干净，同时请确保不要产生划痕
Cut
Inrush current
1. The luminaire shall be installed by a qualified electrician and wired in accordance with the latest IEE electrical regulations or the national
requirements.
灯具应由有资格的电工安装，接线要符合IEE电气标准或国家标准。
2. Please switch off the power supply before replacing the product or connection! 更换灯具或接线时，请务必先关闭电源！
3. Do not place readily flammable material near the luminaire. 请不要将高温易燃物品放在灯具附近，以免引起火灾或触电。
4. In case of operation failure, please switch off the power and contact your nearest dealer.
如发现异常或操作有任何问题请务必先切断电源, , 然后与经销商联系。
5. The corrosive atmosphere or hazardous materials such as sulfur, chlorine, phthalate, etc. must be avoided during the use and storage.
灯具避免在腐蚀性环境或者含有有害物质，例如硫化物，卤化物，邻苯二甲酸酯等环境中存储和使用。
6. Basic insulation should be provided between LV supply and control conductors. LV电源和控制导体之间是基本绝缘。
7. The control gear and/or the external flexible cable contained in this luminaire shall only be replaced by the manufacturer or his service agent or
a similar qualified person.
此灯具包含的驱动器和/或外部线缆只能由制造商或其服务代理或有类似资格的人来更换。
8. The light source contained in this luminaire shall only be replaced by the manufacturer or his service agent or a similar qualified person.
此灯具内的光源应由制造商或其服务代理商或有类似资格的人来更换。
9. Indoor use only. 本灯具仅限室内使用。
10. Before use, luminaire must be grounded first. it is also ensure that the luminaire are always grounded when in use.
灯具使用前，必须先接地。整个使用过程中，也必须确保灯具始终接地。
11. The manufacturer will not be held responsible for improper usage or modifications of the product.
由不当使用或自行更改产品结构而导致的损坏，生产商不承担责任。
12. The product is IPX0 & as such is not protected against water ingress. we strongly recommend that the environment in which the luminaire is to
be installed is suitably checked. If the above advice is not taken and the luminaires are subject to water ingress, Philips / Signify cannot guarantee safe
failure & product warranty will become void.
本产品防护等级为IPX0, 不能防止进水，强烈建议安装本产品前对使用环境的适应性进行检查评估。
一但有进水，产品可能会发生电气故障或安全事故，飞利浦/昕诺飞对此不承担质保责任。
Product Type
Run Current
(A)(@220V)
Start (Inrush)
Current(A)
/ Ipeak (A)
Start Current
Duration (μs) /
T(@50% of Ipeak)
(μs)
Touch current
or protective
conductor
current (mA)
MCB Type B 16A
(or Type C 16A)
Max no. fitting (pcs)
SP800P LED21/840 L60W6 SD 0.088 14 240 0.7 35
SP800P LED21/840 L60W6 SD PSD 0.088 17 180 0.7 42
SP800P LED41/840 L120W6 SD 0.176 14 240 0.7 35
SP800P LED41/840 L120W6 SD PSD 0.172 17 180 0.7 42
SP800P LED52/840 L150W6 SD 0.235 20 240 0.7 24
SP800P LED52/840 L150W6 SD PSD 0.217 24 220 0.7 15
SP800P LED20/940 L60W6 SD PSD 0.088 17 180 0.7 42
SP800P LED38/940 L120W6 SD PSD 0.172 17 180 0.7 42
7Close with End Cap
安装端盖
x 2
9Secure Top Cap
安装上盖
x 2
Top cap alignment guide
上盖对齐导向
8Remove Protection Film
撕掉保护膜
Push the end cap
to position
将端盖推至位置
1
Tighten the screw
锁紧螺丝
2
:表示该有害物质至少在该部件所的某一均质材料中的含量超出GB/T 26572规定的限量要求。
铅 镉 多溴联苯
部件名称
外壳及其
它零部件
产品中有害物质的名称及含量
:表示该有害物质在该部件所有均质材料中的含量均在GB/T 26572规定的限量要求以下。
(Pb)
Applicable to China Only
(Cd) (PBB)
LED灯板/光源
汞 六价铬 多溴二苯醚
驱动器(板)，铜
制及电子零部件
本表格依据SJ/T 11364的规定编制
有害物质
(Hg) (Cr(VI)) (PBDE)
透镜光学部件
/
