Flashforge Adventurer 5M ユーザーマニュアル

中文P35

1. Please refer to this Guide for initial printer setup.

2. Hot! Avoid touching the heating nozzle in operation.

3. Moving parts in the printer may cause injuries. Do not wear

gloves or other sources of entanglement in operation.

1. 请参照本指南完成打印机的初始准备。

2. 高温危险！打印机喷嘴在工作时会被加热，操作时请避免接触！

3. 可动部件可能会造成卷入挤压和切割伤害。操作机器时请不要

佩戴手套或缠绕物。

Do not power on the printer until installation is completed.

请勿在打印机安装完成之前通电。

安全提示

Safety Notice

用户使用手册

Adventurer 5M / 冒险家5M

User Guide

EN/CN-A01

For more information, you can visit the Flashforge oﬃcial website.

www.ﬂashforge.com - [Support]

CONTENTS

01

Notice

1. Equipment Introduction

1.1 - Printer Components

1.2 - Printer Parameters

2. Initial Setup

2.1 - Unboxing

2.2 - Packing List

2.3 - Installing the Spool Holder and Filament Guide Tube

2.4 - Installing the Screen

2.5 - Unlocking the Build Plate

2.6 - First Print

3. Software Introduction & Installation

4. Printing

4.1 - Filament Loading and Changing

4.1.1 - Filament Loading

4.1.2 - Filament Changing

4.2 - Network Connection

4.2.1 - Wireless Network Connection

4.2.2 - Wired Network Connection

4.3 - Printing Methods

4.3.1 - Printing via USB

4.3.2 - Printing via Wi-Fi transfer

4.3.3 - Printing via Cloud

4.4 - Model Removal After Printing

5. Introduction to Auxiliary Functions

5.1 - Leveling and Calibration

5.2 - Other Function Settings

6. Maintenance

6.1 - Suggestions on Platform Plate Usage

6.2 - Suggestions on Nozzle Usage

6.3 - General Maintenance

7. Q&A

8. Help and Support

02

04

05

06

08

09

11

12

13

16

21

24

25

26

28

29

30

31

34

NOTICE

SAFETY NOTICE: PLEASE CAREFULLY READ AND STRICTLY FOLLOW

ALL THE SAFETY WARNINGS AND NOTICES BELOW ALL THE TIME.

WORK ENVIRONMENT SAFETY

Please keep the workspace clean and tidy.

Please ensure the equipment operates away from combustible gases, liquids, and

dust. High temperatures generated during operation may react with combustible

gases, liquids, or airborne dust, potentially causing fires.

Children and untrained individuals should not operate the equipment alone.

Note: Each 3D printer undergoes printing tests before leaving the factory. Filament

residue on the nozzle or slight scratches on the build plate are normal and do

not affect usage.

ELECTRICAL SAFETY

PERSONAL SAFETY

Do not touch the extruder, build plate, etc., during printing.

Do not touch the extruder and build plate after finishing printing to avoid high

temperature burns or mechanical damage.

Do not wear scarves, masks, gloves, jewelry, or other objects that can easily get

tangled into the equipment while operating it.

Do not operate the equipment while you are tired or under the influence of drugs,

alcohol or medication.

Please properly ground the equipment. Do not modify the plug. Ungrounded

equipment/improperly grounded equipment/modified plug will inevitably increase

the risk of electric leakage.

Avoid exposing the equipment to damp or direct sunlight environments. Humidity

will increase the risk of electric leakage. Exposure to sunlight will accelerate the

aging of plastic parts.

Make sure to only use the power cord provided by Flashforge.

Do not use the equipment during thunderstorms.

Please turn off the equipment and unplug it if it is not in use for a long time.

Keep the inside of the equipment clean. Do not drop metal objects into the grooves

at the bottom of the build plate.

Please clean up filament debris in time. It is recommended to operate this outside

the equipment.

Any modification of the equipment by yourself will void the warranty.

Please keep the distance between the extruder and build plate for at least 50mm

during filament loading. Too-close distance may cause nozzle clogs.

Please operate the equipment in a well-ventilated environment.

Do not use the equipment for illegal activities.

Do not use the equipment to make food storage containers.

Do not place printed models into your mouth.

CAUTIONS

02

EQUIPMENT ENVIRONMENT REQUIREMENTS

EQUIPMENT PLACEMENT REQUIREMENTS

COMPATIBLE FILAMENT REQUIREMENTS

FILAMENT STORAGE REQUIREMENTS

LEGAL STATEMENT

The equipment must be placed in a dry and well-ventilated environment.

A distance of at least 20cm must be reserved around the front, back, left and right

sides of the equipment. Recommended storage temperature: 0-40°C

When using this equipment, it's recommended to use Flashforge's filaments.

If non-Flashforge filaments are used, there will be certain differences in material

properties, and print parameters may need adjustments.

Please store filaments in a dry and dust-free environment after unpacking. It is

recommended to use the matching filament dry box for storage.

Room temperature: 15-30℃; Humidity: 20-70RH%

Users are not authorized to make any modifications to this User Guide.

Flashforge shall not be held responsible for any safety incidents resulting from the

disassembly or modification of the equipment by the customer. No one is allowed

to modify or translate this Guide without Flashforge's permission. This Guide is

protected by copyright, and Flashforge reserves the right of the final interpretation

of this Guide.

First Edition (September 2023)

03

1.Equipment Introduction

1.1 Printer Components

04

1

2

3

4

6

5

1. Extruder

2. Touch Screen

3. Build Plate

4. USB Port

5. Screw Holes for Spool Holder

6. Filament Detection Sensor

7. Ethernet Input

8. Power Switch

9. Power Socket

89

7

1.2 Printer Parameters

05

Machine Name

Extruder Quantity

Printing Precision

Positioning Accuracy

Layer Thickness

Build Volume

Nozzle Diameter

Printing Speed

Max Acceleration

Max Travel Speed

Max Extruder Temperature

Supported Filament

Power Supply

Device Size

Net Weight

Connectivity

Operating Temperature

Compatible Operating System

Slicing Software

Max Platform Temperature

Leveling Method

Filament Run-out Reminder

Power Loss Recovery

Smart Touch Screen

Build Plate

Adventurer 5M

1

±0.2mm [testing based on 100mm cubes]

X/Y-axis：0.0125mm, Z-axis：0.0025mm

0.1-0.4mm

220 x 220 x 220mm

0.4mm default [0.6/0.8/0.25mm optional]

10-300mm/s

20000mm/s²

600mm/s

280℃

*PLA/*PETG/*TPU [0.4mm nozzle]

PLA-CF/PETG-CF [0.6/0.8mm nozzle]

Input: AC 100~120V/200~240V，50/60Hz，350W

363 x 376 x 413mm

[excluding the display screen and spool holder]

363 x 402 x 448mm

[including the display screen, excluding the spool holder]

10.8kg

USB/Wi-Fi/Ethernet

15-30℃

Windows 7/8/10/11; Linux: support version Ubuntu

20.04 or later; Mac OS: support version 10.9 or later

FlashPrint 5

110℃

One-click auto leveling

√

4.3-inch

PEI ﬂexible steel plate

Note: Materials marked with * are recommended for printing.

Safety Notice: Do not power on the printer until installation is completed.

2. Initial Setup

2.1 Unboxing

06

1. Open the box. 2. Remove the upper foam packaging,

Quick Start Guide and After-sales

Service Card.

3. Take out the machine, place it on a level

workspace and remove the packaging

bags and tapes.

4. Remove the filament, power cable, screen,

and accessory box from the chamber

protective foam. Remove the inner protective

foam from the extruder.

07

5. Move the extruder and chain according to the arrow direction.

6. Remove the foam.

2.2 Packing List

08

3D Printer Filament After-sales

Service Card

Spool Holder

(with 2 screws)

Touch Screen

Quick Start Guide Grease

Power Cable

Glue Diagonal Pliers

Allen Wrench

2.0 2.5 3.0

Screwdriver

Unclogging Pin Tool

09

1. Take out the two screws and spool holder from

the accessory box.

2. Install the spool holder at the position shown in the figure

with the two screws. (Note: Please tighten them

using a 2.0mm Allen wrench.)

2.3 Installing the Spool Holder and Filament Guide Tube

10

3. Insert the filament guide tube to the extruder.

4. Insert the other end of the filament guide tube into the filament detection sensor.

11

2.4 Installing the Screen

1. As shown in the picture,

insert the screen cable

into the screen connector.

a. Lift the buckle on the screen's cable socket to the indicated position (Fig. ①), then insert the

screen cable into the socket connector. Note: Ensure proper insertion and check alignment

of the indicator line with socket.

b. Press down the buckle on the cable socket to the indicated position according to the arrow

direction (Fig. ②).

12

Before installation, please remove the tape of the screen cable. Tear it off gently to

avoid damaging the cable.

Note

12

Please ensure the platform has been cleared up!

Note

2.5 Unlocking the Build Plate

Please use a 2.0mm Allen wrench to remove four screws which lock the build plate (as indicated

by the arrow).

2. Insert the buckle on the back of the screen into the printer's slot, and push the screen

according to the arrow direction to lock it in place.

2.6 First Print

13

1. Power on the printer, turn on the power switch, and wait for the screen to respond.

* The interface layout may change whenever there is an upgrade of firmware.

Power Switch

2. Following the guide on the screen, select

the language.

3. Click [Next] and the machine will perform the first calibration. Vibrations and noise during

calibration are normal. (Note: Please keep the machine on a stable surface and do not move

it during calibration.)

14

4. Load filament following the on-screen startup boot:

a. Cut off the bent part of the filament end.

b. Hang the filament on the spool holder. Pass it through the filament sensor until it's seen from

the other end of the filament guide tube. Push it forward to the feed roller, until it can not go

further. (Please use PLA filament for the first print on initial setup).

C1. Click [Load] and select [PLA] for the first print. C2. Wait for the extruder to heat up.

15

If no filament is extruded, manually insert the filament into the inlet and click [Back] to retry.

Feel for filament movement until it is extruded.

6. Click [Print] and the machine starts

printing the built-in file (configured

for PLA material).

5. Please clear the filament residues on the

nozzle and platform. Users must apply

glue to the platform so as to improve

adhesion for the first print.

Note

C3. Feeding will begin after heating. Successful filament extrusion from the nozzle indicates

successful loading. Lastly, confirm the filament guide tube is properly inserted.

Note

3. Software Introduction & Installation

Before printing 3D model files, you need to configure slicing presets for the corresponding printer.

Recommended slicing software: OrcaSlicer / FlashPrint 5

Before reading the brief instructions, please ensure you have reviewed the Quick

Start Guide and completed the first print.

Slicing Software Instructions for Adventurer 5M Series

Pre-printing Steps:

Obtain the 3D file

(STEP/STL/OBJ)

Download and

install the slicing

software

Use the slicing software

to convert the file into

the machine-readable

format

Import the sliced file via

a USB flash drive or

network transfer to the

printer for printing

This slicing software, created by the open-source community, offers more open configuration

options. Experienced users are recommended to use this slicing software.

1. Download the latest slicing software from the official website:

https://github.com/SoftFever/OrcaSlicer/releases.

2. Find the OrcaSlicer software package on the USB flash drive and install the version that matches

your system.

Files can be imported by project, requiring a click on the project file each time you open it.

Alternatively, configs can be imported, eliminating the need to do so each time, but this may not

be compatible with higher software versions.

Open-source Slicing Software

OrcaSlicer

01 02 03 04

Download and Installation Instructions

Note

16

* The steps are illustrated for one machine type.

How to Use OrcaSlicer (Import Project Files)

1. Open the installed OrcaSlicer. 2. Click [Open Project].

3. The profile should be in .3mf format. You

can find the corresponding file on the USB

flash drive. Drag it directly into OrcaSlicer,

or open it directly (if the machine is not

configured with a USB flash drive, please

download the corresponding profile from

Flashforge's official website).

4. After importing the profile, the software

interface will display the corresponding

printer, and you can select the desired

printing material.

17

* The steps are illustrated for one machine type.

5. Select the model file to be printed. You can

drag it directly into the software, or click

[File] - [Import] to import the model file

(STL/STEP/OBJ/3MF, etc.).

6. Click [Slice all]. Once slicing is completed, click

[Export G-code file], save the file to a USB flash

drive, and then insert it into the printer for

printing.

How to Use OrcaSlicer (Import Configs)

1. Open the installed OrcaSlicer.

3. The config file should be in .json format. You

can find the corresponding files on the USB

flash drive, select all, and open it (if the

machine is not configured with a USB flash

drive, please download the corresponding

config files from Flashforge's official website).

2. Click [File] - [Import] - [Import Configs...].

18

ページを読み込んでいます...

Flashforge Adventurer 5M ユーザーマニュアル

関連論文

その他の書類