ekwb EK-Nucleus AIO CR240 Lux D-RGB インストールガイド

INSTALLATION MANUAL

EKNucleus AIO

CR360 Lux D-RGB / CR240 Lux D-RGB

Compatible with:

Intel Socket 115X/1200/1700/20xx CPUs

AMD Socket AM4/AM5 CPU

To ensure safe and easy installation, please carefully read

this manual before beginning the installation process!

2nd Revision

1. SAFETY PRECAUTIONS 4

2. SPECIFICATIONS 4

3. ENCLOSED IN THIS PACKAGE 5

ACCESSORY BOX 5

4. INSTALLATION  INTEL LGA 115X/1200/1700 SOCKET 6

STEP 1: REMOVING THE MOTHERBOARD 6

STEP 2: ATTACHING THE BACKPLATE TO THE MOTHERBOARD 6

STEP 3: ATTACHING MOUNTING SCREWS 6

STEP 4: INSTALLING THE FANS TO THE RADIATOR 6

STEP 5: REMOVING THE COLD-PLATE PROTECTIVE COVER 6

STEP 6: MOUNTING-BRACKETS INSTALLATION 6

STEP 7: PUMP UNIT INSTALL ATION 6

STEP 8: INSTALLING THE ASSEMBLY OF FANS AND RADIATOR INTO A PC CASE 7

STEP 9: PUMP – CONNECTING CABLES 7

STEP 10: FANS – CONNECTING CABLES 8

STEP 11: PUMP TOP ORIENTATION 9

OPTIONAL STEP! APPLYING THE THERMAL COMPOUND 9

5. INSTALLATION  INTEL LGA 20XX SOCKET 9

STEP 1: ATTACHING MOUNTING SCREWS (LGA 20XX) 9

6. INSTALLATION  AMD AM4/AM5 SOCKET 9

STEP 1: REMOVING OF THE ORIGINAL PLASTIC HOLD-DOWN CLAMPS (AMD) 9

STEP 2: ATTACHING MOUNTING SCREWS (AMD) 9

STEP 3: INSTALLING THE FANS TO THE RADIATOR (AMD) 9

STEP 4: REMOVING THE COLD-PLATE PROTECTIVE COVER (AMD) 10

STEP 5: MOUNTING-BRACKETS INSTALLATION (AMD) 10

STEP 6: PUMP UNIT INSTALLATION (AMD) 10

STEP 7: INSTALLING THE ASSEMBLY OF FANS AND RADIATOR INTO A PC CASE (AMD) 10

STEP 8: PUMP – CONNECTING CABLES (AMD) 11

STEP 9: FANS – CONNECTING CABLES (AMD) 11

STEP 10: PUMP TOP ORIENTATION (AMD) 12

OPTIONAL STEP! APPLYING THE THERMAL COMPOUND 12

7. GENERAL SAFETY WARNINGS 12

8. SUPPORT AND SERVICE 13

9. SOCIAL MEDIA 13

TABLE OF CONTENTS

- 4 -

Please follow the instructions in this manual for proper installation. Improper installation may

result in damage to your equipment. EK Water Blocks assumes no liability whatsoever, expressed

or implied, for the use of these products, nor their installation. The following instructions are

subject to change without notice. Please visit our website at www.ekwb.com for updates.

1. SAFETY PRECAUTIONS

1. Keep and store the product away from the reach of children.

2. Check the component list and condition of the product before installation. If there is any

problem, contact the shop where you purchased the product to get a replacement or refund.

3. EKWB d.o.o. is not responsible for any damages due to external causes, including but not

limited to, improper use, problems with electrical power, accident, neglect, alteration, repair,

improper installation, and improper testing.

4. CPU and motherboard are subject to damage if the product is incorrectly installed.

5. Excessive force exerted on the fan may cause damage to the fan and/or system.

6. This product is a CPU liquid cooling solution kit, composed of individual, original EKWB parts.

Combining this liquid cooling unit with parts, other than EK Water Blocks products, may lead

to warranty loss.

7. Product design and speciﬁ cations may be revised to improve quality and performance.

8. You must not run the pump below 20% RPM. The pump must stay within a 20-100% PWM

duty cycle at all times. We recommend always running the pump at 100%. (For help on how to

control the PWM, please refer to your motherboard instructions.)

2. SPECIFICATIONS

Model EK-Nucleus AIO CR240 Lux

D-RGB

EK-Nucleus AIO CR360 Lux

D-RGB

Radiator Dimensions 281x124x27 mm 400x124x27 mm

Fin material Al Al

Fan

Dimensions 120x120x25 mm (2x) 120x120x25 mm (3x)

Speed 550-2300 RPM ±10%

(PWM: 20-100%)

550-2300 RPM ±10%

(PWM: 20-100%)

Air Flow 72 CFM 72 CFM

Life Expectancy 70.000 hours 70.000 hours

Noise Level 36 dB 36 dB

Bearing Type FDB bearing FDB bearing

Fan Connector 4Pin 4Pin

Fan Rated Voltage 12V 12V

D-RGB Connector 3Pin 3Pin

D-RGB Rated Voltage 5V 5V

Pump

Dimensions (mm) 82.3x69.2x61.6 mm 82.3x69.2x61.6 mm

RPM 3100 RPM ± 10%

(PWM: 20-100%)

3100 RPM ± 10%

(PWM: 20-100%)

Life Expectancy 70.000 hours 70.000 hours

Noise Level 18.5 dB 18.5 dB

Input Current 0.37 ±10% A 0.37 ±10% A

- 5 -

3. ENCLOSED IN THIS PACKAGE

E K - F P T F A N 1 2 0 D - R G B F u l l P r e s s u r e T e c h n o l o g y F a n

(2x / 3x – number of fans depends on the AIO version)

EK-Nucleus AIO CR240 Lux D-RGB /

EK-Nucleus AIO CR360 Lux D-RGB

(1x)

Tube of Thermal Paste

1x

ACCESSORY BOX

Phillips Head Screw

UNC 6-32 x 30mm

(4 mm thread length)

8x / 12x

Phillips Head Screw

UNC 6-32 x 34mm

8x / 12x

Phillips Head Screw

UNC 6-32 x 6mm

8x / 12x

Mounting Plate Phillips Head

M3x4mm (for the installation of

mounting brackets)

4x

Mounting thumb screw for

Intel LGA 115x/LGA1200/

LGA1700/AMD AM4/AM5 socket

4x

Mounting thumb screw for

Intel LGA 20XX socket

4x

Thumb nut (Intel /AMD)

4x

Spring

4x

Intel LGA 115x/1200 Backplate

1x

Intel mounting bracket

1x

Intel LGA 1700 Backplate

1x

AMD mounting bracket

1x

Mounting Screw Tool

1x

Extension cable 500mm

Accessory box

(1x)

User Manual

(1x)

INSTALLATION MANUAL

EKNucleus AIO

CR360 Lux D-RGB / CR240 Lux D-RGB

Compatible with:

Intel Socket 115X/1200/1700/20xx CPUs

AMD Socket AM4/AM5 CPU

To ensure safe and easy installation, please carefully read

this manual before beginning the installation process!

2nd Revision

- 6 -

Thumb Nut

Spring

4. INSTALLATION  INTEL LGA 115X/1200/1700 SOCKET

STEP 1: REMOVING THE

MOTHERBOARD

If your PC case doesn’t have a cutout from the

bottom CPU side of the motherboard, you will

ﬁ rst need to remove the motherboard from

your computer.

STEP 2: ATTACHING THE BACKPLATE

TO THE MOTHERBOARD

Install the Intel backplate for LGA

115x/1200/1700 socket to the back of your

motherboard. Choose the right backplate

depending on which chipset you are using.

Align the holes on the motherboard with the

holes on the backplate.

Intel LGA 115x / 1200

or 1700 Backplate

STEP 3: ATTACHING MOUNTING

SCREWS

Install 4x mounting thumb screws through

your motherboard to the backplate. The

screws can be installed by using Mounting

Screw Tool. Do not use other tools, because

you may damage the motherboard. (i.e. pliers).

Mounting thumb

screw for INTEL

LGA 115x / 1200

/ 1700 and AMD

AM4/AM5 socket

STEP 6: MOUNTING-BRACKETS

INSTALLATION

Use 4x M3x4 screws to install Intel bracket on

the pump unit.

Be careful not to touch or damage the pre-

applied thermal compound.

M3x4

Intel Mounting

Bracket

STEP 4: INSTALLING THE FANS TO

THE RADIATOR

Assemble the fans (2x or 3x ... depending on

the AIO version) to the radiator with the UNC

6-32 x 30mm screws.

UNC

6-32 x 30 mm

Fan

Radiator

Mounting Screw Tool

STEP 5: REMOVING THE COLD-PLATE

PROTECTIVE COVER

Remove the protective cover from the

backside of the pump unit. It is there only to

prevent damage to the cold-plate and the

pre-applied thermal compound that is on the

cold-plate.

When removing the protective cover and

proceeding with installation, be careful not

to touch or damage the pre-applied thermal

compound.

STEP 7: PUMP UNIT INSTALLATION

Wipe the CPU’s contact surface (using a

non-abrasive cloth or a Q-tip as shown in the

sample image).

Align the pump unit over the mounting screws

and CPU as shown in the picture.

Place the enclosed compression springs and

thumb nuts over the mounting screws (4x).

Start fastening two thumb nuts at a time,

preferably in a cross pattern, and do not

tighten them fully until all of them are partially

screwed in.

Non-abrasive

cloth IHS

Protective Cover

Pre-applied

thermal

Compound

- 7 -

STEP 9: PUMP – CONNECTING

CABLES

D-RGB Connector

4-pin

PWM

STEP A:

Plug the 4-pin PWM connector from the pump

to the motherboard.

STEP B:

Plug the 3-pin connector from the pump D-RGB LED

light to the D-RGB HEADER on the motherboard.

The LED will work if the pin layout on the header is as

follows: +5V, Digital, empty, Ground. Alternatively, with

some motherboards you can use a VDG connector

instead of a D-RGB to connect the LED.

Please ensure that the arrow indicated on

the connector is plugged into the +5V line

as indicated on your motherboard. If you

put LED Diode to the 12V RGB HEADER

you can damage the LEDs.

Connector is the same on D-RGB and RGB

versions, but D-RGB version has 3 cables

from connector to PCB; RGB version has

4 cables. If you connect D-RGB led to

ordinary RGB header you can damage

your motherboard or LED strip.

STEP 8: INSTALLING THE ASSEMBLY

OF FANS AND RADIATOR INTO A PC

CASE

Attach the assembly of radiator and the fan(s)

to the PC case with the UNC 6-32 x 6mm

screws.

EK-AIO Nucleus 240

EK-AIO Nucleus 360

UNC 6-32 x 6 mm

(8x)

UNC 6-32 x 6 mm

(12x)

Radiator on top (recommended)

Vertical placement of the radiator with

tubing at the bottom (recommended)

Avoid vertical placement of the radiator

with tubing at the top

Avoid radiator at the bottom

- 8 -

STEP A:

Connect the 4-pin fan connector from the

extension cable directly to the CPU fan header

on the motherboard. Always use CPU fan

header when possible.

STEP 10: FANS – CONNECTING

CABLES

STEP B:

Plug the 3-pin D-RGB connector from the

extension cable to the D-RGB header on the

motherboard.

Please ensure that the arrow indicated on

the connector is plugged into the +5V line

as indicated on your motherboard. If you

put LED Diode to the 12V RGB HEADER

you can damage the LEDs.

Connector is the same on D-RGB and RGB

versions, but D-RGB version has 3 cables

from connector to PCB; RGB version has

4 cables. If you connect D-RGB led to

ordinary RGB header you can damage

your motherboard or LED strip.

D-RGB Header

RGB Header

Fan Connector

Male Connector

Female Connector

Fan Connector

D-RGB Connector

Female Connector

STEP C:

Connect the female connector from the

extension cable to the male connector from

the ﬁ rst fan in line.

Be careful to turn the micro-ﬁ t connector

correctly.

Male Connector

Female Connector

STEP D:

In the case of the EK-Nucleus AIO CR240

D-RGB or EK-Nucleus AIO CR360 D-RGB

version, connect the second and third fan in

series with the “daisy-chain”.

Be careful to turn the connector correctly.

Male

Connector

Female

Connector

- 9 -

5. INSTALLATION  INTEL LGA 20XX SOCKET

STEP 1: ATTACHING MOUNTING

SCREWS (LGA 20XX)

LGA 20xx (2066 / 2011 V3 / 2011) socket

motherboards do not require backplate

installation. Install 4x LGA 20XX mounting

thumb screws into M4 threaded stubs on the

LGA 20XX socket integrated latch

mechanism (ILM). The screws can be

installed by using Mounting Screw Tool.

Do not use other tools, because you may

damage the motherboard. (i.e. pliers).

Continue installation by following

the instructions from Step 4 on

page 6

OPTIONAL STEP! APPLYING THE

THERMAL COMPOUND

This step is relevant only in the case of a

second installation of AIO or if you have

damaged the pre-applied paste on the

backside of the pump unit. For the ﬁ rst

installation, you don’t need to apply the

additional thermal compound to the CPU’s

contact surface.

Wipe the CPU’s contact surface (using a non–

abrasive cloth or Q-tip, as shown in sample

photo). On a clean IHS, apply a line of thermal

compound and spread it over the whole

CPU heat spreader (IHS) with a credit card or

equivalent.

For help on how to control the D-RGB lights,

please refer to your motherboard instructions.

12 34

LGA 20XX M3.5

Thumb Screw

6. INSTALLATION  AMD AM4/AM5 SOCKET

STEP 1: REMOVING OF THE

ORIGINAL PLASTIC HOLD-DOWN

CLAMPS (AMD)

Using a Philips head screwdriver, remove the

four UNC 6-32 screws securing the original

plastic hold-down clamps around the socket

as shown on the sketch. Keep the original

AMD® backplate and remove the hold-down

clamps and store them away. See the image for

further part identiﬁ cation.

STEP 2: ATTACHING MOUNTING

SCREWS (AMD)

Install 4x mounting thumb screw for AMD

AM4/AM5 socket onto your motherboard. The

screws can be installed by using Mounting

Screw Tool. Do not use other tools, because

you may damage the motherboard. (i.e. pliers).

Mounting thumb

screw for INTEL

LGA 115x / 1200

/ 1700 and AMD

AM4/AM5 socket

Hold-down

clamps

UNC 6-32 Screws

STEP 3: INSTALLING THE FANS TO

THE RADIATOR (AMD)

Assemble the fans (2x or 3x ... depending on

the AIO version) to the radiator with the UNC

6-32 x 30mm screws.

STEP 11: PUMP TOP ORIENTATION

Lift the top, rotate it until the EK logo is oriented

correctly, and put it back down. The magnets

will hold the top in place.

Congratulations! You have successfully

installed your EK-Nucleus AIO.

Non-abrasive

Cloth

IHS

UNC

6-32 x 30 mm

Fan

Radiator

Mounting Screw Tool

- 10 -

STEP 7: INSTALLING THE ASSEMBLY

OF FANS AND RADIATOR INTO A PC

CASE (AMD)

Attach the assembly of radiator and the fan(s)

to the PC case with the UNC 6-32 x 6mm

screws.

Radiator on top (recommended)

Vertical placement of the radiator with

tubing at the bottom (recommended)

STEP 5: MOUNTING-BRACKETS

INSTALLATION (AMD)

Use 4x M3x4 screws to install AMD bracket on

the pump unit.

Be careful not to touch or damage the pre-

applied thermal compound.

STEP 4: REMOVING THE COLD-PLATE

PROTECTIVE COVER (AMD)

Remove the protective cover from the

backside of the pump unit. It is there only to

prevent damage to the cold-plate and the

pre-applied thermal compound that is on the

cold-plate.

When removing the protective cover and

proceeding with installation be careful not

to touch or damage the pre-applied thermal

compound.

STEP 6: PUMP UNIT INSTALLATION

(AMD)

Wipe the CPU’s contact surface (using a

non-abrasive cloth or a Q-tip as shown in the

sample image).

Align the pump unit over the mounting screws

and CPU as shown in the picture.

Place the enclosed compression springs and

thumb nuts over the mounting screws (4x). Start

fastening two thumb nuts at a time, preferably

in a cross pattern, and do not tighten them fully

until all of them are partially screwed in.

Thumb Nut

Spring

Non-abrasive

cloth IHS

Protective Cover

Pre-applied

thermal

Compound

M3x4

AMD Mounting

Bracket

EK-AIO Nucleus 240

EK-AIO Nucleus 360

UNC 6-32 x 6 mm

(8x)

UNC 6-32 x 6 mm

(12x)

- 11 -

STEP 8: PUMP – CONNECTING

CABLES (AMD)

D-RGB Connector

4-pin

PWM

STEP A:

Plug the 4-pin PWM connector from the pump

to the motherboard.

STEP B:

Plug the 3-pin connector from the pump D-RGB LED

light to the D-RGB HEADER on the motherboard.

The LED will work if the pin layout on the header is as

follows: +5V, Digital, empty, Ground. Alternatively, with

some motherboards you can use a VDG connector

instead of a D-RGB to connect the LED.

Please ensure that the arrow indicated on

the connector is plugged into the +5V line

as indicated on your motherboard. If you

put LED Diode to the 12V RGB HEADER

you can damage the LEDs.

Connector is the same on D-RGB and RGB

versions, but D-RGB version has 3 cables

from connector to PCB; RGB version has

4 cables. If you connect D-RGB led to

ordinary RGB header you can damage

your motherboard or LED strip.

Avoid vertical placement of the radiator

with tubing at the top

Avoid radiator at the bottom

STEP A:

Connect the 4-pin FAN connector from the

extension cable directly to the CPU fan header

on the motherboard. Always use a CPU fan

header when possible.

STEP 9: FANS – CONNECTING

CABLES (AMD)

Fan Connector

Male Connector

Female Connector

Fan Connector

D-RGB Connector

Female Connector

- 12 -

STEP B:

Plug the 3-pin D-RGB connector from the

extension cable to the D-RGB header on the

motherboard.

Please ensure that the arrow indicated on

the connector is plugged into the +5V line

as indicated on your motherboard. If you

put LED Diode to the 12V RGB HEADER

you can damage the LEDs.

Connector is the same on D-RGB and RGB

versions, but D-RGB version has 3 cables

from connector to PCB; RGB version has

4 cables. If you connect D-RGB led to

ordinary RGB header you can damage

your motherboard or LED strip.

D-RGB Header

RGB Header

OPTIONAL STEP! APPLYING THE

THERMAL COMPOUND

This step is relevant only in the case of a

second installation of AIO or if you have

damaged the pre-applied paste on the

backside of the pump unit. For the ﬁ rst

installation, you don’t need to apply the

additional thermal compound to the CPU’s

contact surface.

Wipe the CPU’s contact surface (using a non–

abrasive cloth or Q-tip, as shown on sample

photo). On a clean IHS, apply a line of thermal

compound and spread it over the whole CPU

heat spreader (IHS) with a credit card or

equivalent.

For help on how to control the D-RGB lights,

please refer to your motherboard instructions.

12 34

STEP 10: PUMP TOP ORIENTATION

(AMD)

Lift the top, rotate it until the EK logo is oriented

correctly, and put it back down. The magnets

will hold the top in place.

Congratulations! You have successfully

installed your EK-Nucleus AIO.

First aid measures in case of:

Skin exposure to coolant: Remove contaminated clothing and rinse thoroughly with plenty of

running water or normal saline rinse. If symptoms develop and persist, seek professional medical

attention.

Eye exposure to coolant: Immediately open upper and lower eyelids, ﬂ ush out with running water

or normal saline rinse. If irritation persists, seek professional medical attention.

Inhalation of coolant: Remove yourself from site to fresh air. If symptoms develop and persist,

seek professional medical attention.

Ingestion of coolant: Drink plenty of warm water and do not induce vomiting. In case of doubt or

if felling unwell, seek professional medical attention.

Non-abrasive

Cloth

IHS

7. GENERAL SAFETY WARNINGS

STEP C:

Connect the female connector from the

extension cable to the male connector from

the ﬁ rst fan in line.

Be careful to turn the micro-ﬁ t connector

correctly.

Male Connector

Female Connector

STEP D:

In the case of the EK-Nucleus AIO CR240

D-RGB or EK-Nucleus AIO CR360 D-RGB

version, connect the second and third fan in

series with the “daisy-chain”.

Be careful to turn the connector correctly.

Male

Connector

Female

Connector

- 13 -

For assistance please contact: http://support.ekwb.com/

EKWB d.o.o.

Pod lipami 18

1218 Komenda

Slovenia – EU

8. SUPPORT AND SERVICE

EKWaterBlocks @EKWaterBlocks ekwaterblocks

ekwaterblocks

EKWBofﬁ cial

9. SOCIAL MEDIA

Skin exposure to thermal paste: Wash thoroughly with soap and water for a minimum of 15

minutes. Contaminated clothing should be removed immediately. If irritation persists, obtain

medical attention.

Eye exposure to thermal paste: Flush out thoroughly with running water for a minimum of 15

minutes. If irritation persists, seek professional medical attention.

Inhalation of thermal paste: If adverse effects occur, proceed to an uncontaminated area. If

breathing has been arrested, provide artiﬁ cial respiration immediately. Seek immediate medical

attention.

Ingestion of thermal paste: Drink 2 large glasses of water. Do not induce vomiting. If a large

amount has been ingested, or if discomfort persists, obtain professional medical attention.

PRIROČNIK ZA NAMESTITEV

EKNucleus AIO

CR360 Lux D-RGB / CR240 Lux D-RGB

Združljiv s:

procesorji 1200/1700/20xx s podnožjem Intel 115X,

procesorjem AM4/AM5 s podnožjem AMD.

Za zagotovitev varne in enostavne namestitve natančno

preberite ta priročnik pred začetkom postopka namestitve.

- 15 -

VSEBINA

1. VARNOSTNI UKREPI 16

2. SPECIFIKACIJE 16

3. VKLJUČENO V TEM PAKIRANJU 17

ŠKATLA Z DODATNO OPREMO 17

4. NAMESTITEV  PODNOŽJE INTEL LGA 115X/1200/1700 18

1. KORAK: ODSTRANITEV MATIČNE PLOŠČE 18

2. KORAK: NAMESTITEV HRBTNE PLOŠČE NA MATIČNO PLOŠČO 18

3. KORAK: S PRITRDILNIMI VIJAKI 18

4. KORAK: NAMESTITEV VENTILATORJEV NA HLADILNIK 18

5. KORAK: ODSTRANITEV ZAŠČITNEGA POKROVA HLADILNE PLOŠČE 18

6. KORAK: NAMESTITEV NOSILNE KONZOLE 18

7. KORAK: NAMESTITEV ENOTE ČRPALKE 18

8. KORAK: NAMESTITEV SKLOPA VENTILATORJA IN HLADILNIKA V OHIŠJE RAČUNALNIKA 19

9. KORAK: ČRPALKA – POVEZOVALNI KABEL 19

10. KORAK: VENTILATORJI – POVEZOVALNI KABLI 20

11. KORAK: USMERJENOST ZGORNJEGA DELA ČRPALKE 21

IZBIRNI KORAK! NANAŠANJE TERMIČNE SPOJINE 21

5. NAMESTITEV  PODNOŽJE INTEL LGA 20XX 21

1. KORAK: NAMESTITEV PRITRDILNIH VIJAKOV (LGA 20XX) 21

6. NAMESTITEV  PODNOŽJE AMD AM4/AM5 21

1. KORAK: ODSTRANITEV ORIGINALNIH PLASTIČNIH PRITRDILNIH SPONK (AMD) 21

2. KORAK: NAMESTITEV PRITRDILNIH VIJAKOV (AMD) 21

3. KORAK: NAMESTITEV VENTILATORJEV NA HLADILNIK (AMD) 21

4. KORAK: ODSTRANITEV ZAŠČITNEGA POKROVA HLADILNE PLOŠČE (AMD) 22

5. KORAK: NAMESTITEV NOSILNE KONZOLE (AMD) 22

6. KORAK: NAMESTITEV ENOTE ČRPALKE (AMD) 22

7. KORAK: NAMESTITEV SKLOPA VENTILATORJA IN HLADILNIKA V OHIŠJE RAČUNALNIKA (AMD) 22

8. KORAK: ČRPALKA – POVEZOVALNI KABLI (AMD) 23

9. KORAK: VENTILATORJI – POVEZOVALNI KABLI (AMD) 23

10. KORAK: USMERJENOST ZGORNJEGA DELA ČRPALKE (AMD) 24

IZBIRNI KORAK! NANAŠANJE TERMIČNE SPOJINE 24

7. SPLOŠNA VARNOSTNA OPOZORILA 24

8. PODPORA IN STORITVE 25

9. DRUŽBENA OMREŽJA 25

- 16 -

Za pravilno namestitev upoštevajte navodila v tem priročniku. Neustrezna namestitev lahko povzroči

škodo na vaši opremi. Podjetje EK Water Blocks ne prevzema nobene odgovornosti, izrecne ali

implicitne, za uporabo teh izdelkov in njihovo namestitev. Spodnja navodila se lahko spremenijo brez

predhodnega obvestila. Za posodobitve obiščite našo spletno stran www.ekwb.com.

1. VARNOSTNI UKREPI

1. Izdelek hranite zunaj dosega otrok.

2. Pred namestitvijo preverite seznam komponent in stanje izdelka. V primeru težav se obrnite na

prodajalno, v kateri ste kupili izdelek, da se dogovorite za zamenjavo ali vračilo kupnine.

3. Podjetje EKWB d.o.o. ne odgovarja za kakršno koli škodo, nastalo zaradi zunanjih vzrokov, kar med

drugim vključuje nepravilno uporabo, težave z električnim napajanjem, nesrečo, malomarnost,

spreminjanje, popravila, nepravilno namestitev in nepravilno testiranje.

4. Procesor in matična plošča se lahko poškodujeta, če je izdelek nameščen nepravilno.

5. Čezmerna sila na ventilator lahko poškoduje ventilator in/ali sistem.

6. Ta izdelek je komplet za vodno hlajenje procesorja, sestavljen iz posameznih originalnih delov

EKWB. Kombiniranje te enote za vodno hlajenje z deli, ki niso izdelki podjetja EK Water Blocks,

lahko povzroči izgubo garancije.

7. Oblika in speciﬁ kacije izdelkov se lahko spremenijo za izboljšanje kakovosti in delovanja.

8. Črpalke ne smete zagnati z manj kot 20 % vrtilne frekvence. Črpalka mora ves čas ostati v

obratovalnem ciklu 20–100 % pulznoširinske modulacije. Priporočamo, da črpalka vedno obratuje

na 100 %. (Za pomoč pri nadzoru PWM si oglejte navodila za uporabo vaše matične plošče.)

2. SPECIFIKACIJE

Model EK-Nucleus AIO CR240 Lux

D-RGB

EK-Nucleus AIO CR360 Lux

D-RGB

Hladilnik Mere 281 × 124 × 27 mm 400 × 124 × 27 mm

Material lamel Al Al

Ventilator

Mere 120 × 120 × 25 mm (2x) 120 × 120 × 25 mm (3x)

Hitrost

550–2300 ±10 % vrtilne frekvence

(pulznoširinska modulacija: 20–100 %)

550–2300 ±10 % vrtilne frekvence

(pulznoširinska modulacija: 20–100 %)

Zračni pretok 72 cfm 72 cfm

Življenjska doba 70.000 ur 70.000 ur

Raven hrupa 36 dB 36 dB

Vrsta ležaja Ležaj FDB Ležaj FDB

Vezni element za ventilator

4 kontakti 4 kontakti

Nazivna napetost ventilatorja 12 V 12 V

Vezni element D-RGB 3 kontakti 3 kontakti

Nazivna napetost elementa D-RGB

5 V 5 V

Črpalka

Mere (mm) 82,3 × 69,2 x 61,6 mm 82,3 × 69,2 x 61,6 mm

Vrtilna frekvenca

3100 vrt./min ± 10 % (pulznoširinska

modulacija: 20–100 %)

3100 vrt./min ± 10 % (pulznoširinska

modulacija: 20–100 %)

Življenjska doba 70.000 ur 70.000 ur

Raven hrupa 18,5 dB 18,5 dB

Vhodni tok 0,37 ± 10 % A 0,37 ± 10 % A

- 17 -

3. VKLJUČENO V TEM PAKIRANJU

Ve n t i l a t o r E K - F P T F A N 1 2 0 D - R G B F u l l P r e s s u r e Te c h n o l o g y

(2x/3x – število ventilatorjev je odvisno od različice sistema AIO)

EK-Nucleus AIO CR240 Lux D-RGB /

EK-Nucleus AIO CR360 Lux D-RGB

(1x)

ŠKATLA Z DODATNO OPREMO

Vijak z glavo Phillips

UNC 6–32 x 30 mm

(dolžina navoja 4 mm)

8x/12x

Vijak z glavo Phillips

UNC 6–32 x 34 mm

8x/12x

Vijak z glavo Phillips

UNC 6–32 x 6 mm

8x/12x

Matica za pritrditev z glavo

Phillips M3 x 4 mm

(za namestitev nosilnih konzol)

4x

Vijak za pritrditev na podnožje

Intel LGA 115x/LGA1200/

LGA1700/AMD AM4/AM5

4x

Vijak za pritrditev na podnožje

Intel LGA 20XX

4x

Matica (Intel/AMD)

4x

Vzmet

4x

Hrbtna plošča Intel

LGA 115x/1200

1x

Nosilna konzola Intel

1x

Hrbtna plošča Intel

LGA 1700

1x

Nosilna konzola AMD

1x

Podaljševalni kabel 500 mm

Škatla z dodatno opremo

(1x)

Uporabniški priročnik

(1x)

Tuba termalne paste

1x

Orodje za pritrdilne vijake

1x

INSTALLATION MANUAL

EKNucleus AIO

CR360 Lux D-RGB / CR240 Lux D-RGB

Compatible with:

Intel Socket 115X/1200/1700/20xx CPUs

AMD Socket AM4/AM5 CPU

To ensure safe and easy installation, please carefully read

this manual before beginning the installation process!

2nd Revision

- 18 -

4. NAMESTITEV  PODNOŽJE INTEL LGA 115X/1200/1700

1. KORAK: ODSTRANITEV MATIČNE

PLOŠČE

Če ohišje vašega računalnika nima izreza na

spodnji strani procesorja na matični plošči,

je treba najprej odstraniti matično ploščo z

računalnika.

2. KORAK: NAMESTITEV HRBTNE

PLOŠČE NA MATIČNO PLOŠČO

Namestite hrbtno ploščo Intel za podnožje

LGA 115x/1200/1700 na hrbtno stran matične

plošče. Izberite ustrezno hrbtno ploščo glede

na nabor vezij, ki ga uporabljate. Poravnajte

odprtine matične plošče z odprtinami hrbtne

plošče.

Hrbtna plošča za Intel

LGA 115x/1200 ali 1700

3. KORAK: S PRITRDILNIMI VIJAKI

Namestite 4 pritrdilne palčne vijake skozi

matično ploščo na hrbtno ploščo. Pritrdilne

vijake lahko pri vijačite s pomočjo orodja za

pritrdile vijake. Ne uporabljajte drugih orodij, ker

lahko poškodujete matično ploščo. (tj. klešče)

6. KORAK: NAMESTITEV NOSILNE

KONZOLE

Uporabite 4 vijake M3 x 4 za namestitev

konzole Intel na enoto črpalke.

Pazite, da se ne dotaknete ali poškodujete

predhodno nanesene termične spojine.

M3x4

Nosilna

konzola

Intel

4. KORAK: NAMESTITEV VENTILA-

TORJEV NA HLADILNIK

Namestite ventilatorje (2 ali 3 ... odvisno od različice

AIO) na hladilnik z vijaki UNC 6–32 × 30 mm.

UNC

6–32 x 30 mm

Ventilator

Hladilnik

5. KORAK: ODSTRANITEV

ZAŠČITNEGA POKROVA HLADILNE

PLOŠČE

Odstranite zaščitni pokrov na hrbtni strani

enote črpalke. Ta je nameščen zato, da prepreči

poškodbe hladilne plošče in predhodno

nanesene termične spojine na hladilni plošči.

Pri odstranjevanju zaščitnega pokrova

in nadaljnjem nameščanju pazite, da se

ne dotaknete ali poškodujete predhodno

nanesene termične spojine.

7. KORAK: NAMESTITEV ENOTE

ČRPALKE

Obrišite stično površino procesorja (z

neabrazivno krpo ali vatirano palčko, kot je

prikazano na sliki primera).

Enoto črpalke poravnajte s pritrdilnimi vijaki in

procesorjem, kot je prikazano na sliki.

Priložene tlačne vzmeti in matice namestite

na pritrdilne vijake (4x). Začnite pritrjevati dve

matici hkrati, po možnosti navzkrižno, in jih ne

privijte do konca, dokler niso vse delno privite.

Matica

Vzmet

Neabrazivna

tkanina IHS

Zaščitni pokrov

Predhodno

nanesena

toplotno

prevodna

spojina

Matica za pritrditev na

podnožje za Intel LGA

115x/1200/1700 in

vtičnica AMD AM4/

AM5

Orodje za pritrdilne vijake

- 19 -

D-RGB Connector

4-pin

PWM

9. KORAK: ČRPALKA – POVEZOVALNI

KABEL

KORAK A:

4-polni priključek PWM s črpalke priključite na

matično ploščo.

Korak B:

3-polni priključek z luči D-RGB LED črpalke priključite na

razdelilnik D-RGB na matični plošči. Dioda LED bo delovala,

če je razporeditev polov na razdelilniku naslednja: +5V,

Digital, prazno, Ground. Pri nekaterih matičnih ploščah lahko

kot alternativo namesto razdelilnika D-RGB za priključitev

diode LED uporabite priključek VDG.

Prepričajte se, da je puščica, označena

na priključku, priključena na linijo +5 V,

kot je prikazano na vaši matični plošči. Če

postavite diodo LED na razdelilnik RGB 12

V, lahko poškodujete diode LED.

Priključek je na različicah D-RGB in

RGB enak, vendar ima različica D-RGB

tri kable iz priključka na PCB, različica

RGB pa štiri kable. Če priključite LED

D-RGB na običajen razdelilnik RGB, lahko

poškodujete matično ploščo ali trak LED.

8. KORAK: NAMESTITEV SKLOPA

VENTILATORJA IN HLADILNIKA V

OHIŠJE RAČUNALNIKA

Sklop hladilnika in ventilatorja/-ev pritrdite na

ohišje računalnika z vijaki UNC 6–32 × 6 mm.

Hladilnik na vrhu (priporočeno)

Navpična namestitev hladilnika s cevmi na

dnu (priporočeno)

Nepriporočljiva navpična namestitev

hladilnika s cevmi na vrhu

Nepriporočljiva namestitev hladilnika na

dnu

EK-AIO Nucleus 240

EK-AIO Nucleus 360

UNC 6-32 x 6 mm

(8x)

UNC 6-32 x 6 mm

(12x)

- 20 -

KORAK A:

4-polni priključek za ventilator s

podaljševalnega kabla priključite neposredno

na razdelilnik za ventilator procesorja na

matični plošči. Vedno uporabite razdelilnik za

ventilator procesorja, kadar je to mogoče.

10. KORAK: VENTILATORJI –

POVEZOVALNI KABLI

KORAK B:

3-polni priključek D-RGB s podaljševalnega

kabla priključite na razdelilnik D-RGB na

matični plošči.

Prepričajte se, da je puščica, označena

na priključku, priključena na linijo+5 V,

kot je prikazano na vaši matični plošči. Če

postavite diodo LED na razdelilnik RGB

12 V, lahko poškodujete diode LED.

Priključek je na različicah D-RGB in

RGB enak, vendar ima različica D-RGB

tri kable iz priključka na PCB, različica

RGB pa štiri kable. Če priključite LED

D-RGB na običajen razdelilnik RGB, lahko

poškodujete matično ploščo ali trak LED.

Razdelilnik D-RGB

Razdelilnik RGB

Priključek za

ventilator

Moški priključek

Ženski priključek

Priključek za ventilator

Vezni element D-RGB

Ženski priključek

KORAK C:

Povežite ženski priključek s podaljševalnega

kabla na moški priključek s prvega ventilatorja

v liniji.

Bodite pozorni, da ustrezno obrnete priključek

Micro-Fit.

Moški priključek

Ženski priključek

KORAK D:

Pri različicah EK-Nucleus AIO CR240 D-RGB in

EK-Nucleus AIO CR360 D-RGB povežite drugi

in tretji ventilator zaporedoma z »marjetičnim

povezovanjem«.

Bodite pozorni, da ustrezno obrnete priključek.

Moški

priključek

Ženski

priključek

- 21 -

5. NAMESTITEV  PODNOŽJE INTEL LGA 20XX

1. KORAK: NAMESTITEV PRI-

TRDILNIH VIJAKOV (LGA 20XX)

Matične plošče podnožja LGA 20xx

(2066/2011 V3 /2011) ne zahtevajo

namestitve hrbtne plošče. Namestite 4

pritrdilne palčne vijake LGA 20XX v navojne

čepe M4 na vgrajenem zaklepnem mehanizmu

podnožja LGA 20XX (ILM). Pritrdilne vijake

lahko pri vijačite s pomočjo orodja za pritrdile

vijake. Ne uporabljajte drugih orodij, ker lahko

poškodujete matično ploščo. (tj. klešče)

Nadaljujte z namestitvijo tako,

da sledite navodilom iz četrtega

koraka na strani 18!

IZBIRNI KORAK! NANAŠANJE

TERMIČNE SPOJINE

Ta korak je pomemben samo v primeru druge

namestitve sistema AIO ali če ste poškodovali

predhodno nameščeno pasto na hrbtni strani

enote črpalke. Pri prvi namestitvi vam ni treba

nanesti dodatne termične spojine na stično

površino procesorja.

Obrišite stično površino procesorja (z

neabrazivno krpo ali vatirano palčko, kot je

prikazano na sliki primera). Na čista hladilna

rebra nanesite linijo termične spojine in jo s

kreditno kartico ali podobnim predmetom

nanesite po vseh hladilnih rebrih procesorja

(IHS).

Za pomoč pri nadzoru luči D-RGB si oglejte

navodila za uporabo vaše matične plošče.

12 34

6. NAMESTITEV  PODNOŽJE AMD AM4/AM5

1. KORAK: ODSTRANITEV

ORIGINALNIH PLASTIČNIH

PRITRDILNIH SPONK (AMD)

S križnim izvijačem odstranite štiri vijake

UNC 6-32, ki pritrjujejo originalne plastične

pritrdilne sponke okrog podnožja, kot je

prikazano na skici. Obdržite originalno

hrbtno ploščo AMD® in odstranite pritrdilne

sponke ter jih shranite. Glejte sliko za nadaljnje

prepoznavanje delov.

2. KORAK: NAMESTITEV

PRITRDILNIH VIJAKOV (AMD)

Namestite 4 pritrdilne palčne vijake za

podnožje AMD AM4/AM5 na matično ploščo.

Pritrdilne vijake lahko pri vijačite s pomočjo

orodja za pritrdile vijake. Ne uporabljajte

drugih orodij, ker lahko poškodujete matično

ploščo. (tj. klešče)

Pritrdilne

sponke

Vijaki UNC 6-32

3. KORAK: NAMESTITEV VENTILA-

TORJEV NA HLADILNIK (AMD)

Namestite ventilatorje (2 ali 3 ... odvisno od različice

AIO) na hladilnik z vijaki UNC 6–32 × 30 mm.

11. KORAK: USMERJENOST

ZGORNJEGA DELA ČRPALKE

Dvignite zgornji del in ga vrtite, dokler ni logotip

EK ustrezno obrnjen, nato ga spustite nazaj.

Magneti bodo zadržali zgornji del na mestu.

Čestitamo! Uspešno ste namestili hladilni

sistem EK-Nucleus AIO.

Neabrazivna

tkanina

IHS

UNC

6-32 x 30 mm

Ventilator

Hladilnik

LGA 20XX M3,5

Vijak

Matica za pritrditev

na podnožje za Intel

LGA 115x/1200/1700

in vtičnica AMD AM4/

AM5

Orodje za pritrdilne vijake

ページを読み込んでいます...

ekwb EK-Nucleus AIO CR240 Lux D-RGB インストールガイド

関連論文

その他の書類