Yamaha RX-V2083 クイックスタートガイド

Safety Instructions ................................................ 3

Connections .......................................................... 5

Basic operations ................................................. 16

English

安全说明 ........................................................... 20

连接 ................................................................... 25

基本操作 ........................................................... 37

中文

AV Receiver

Ampli-tuner audio-vidéo

Quick Start Guide

快速启动指南

EN

ZH

TA

2 En

English

A (power) key

Turns on the power of this unit or sets it to the standby mode.

This product is for ordinary homes. Do not use for applications requiring high reliability, such as

managing lives, health care or high-value assets.

For more detailed information, refer to the Owner’s Manual on the CD-ROM. To view the Owner’s

Manual, click on “English” in the screen displayed automatically when you insert the CD-ROM

into your PC, or click on the model name if the screen to select models is displayed, and then click

on “English” in the next screen. Then, follow the onscreen instructions.

If the screen is not displayed automatically, open the “index.html” in the CD-ROM.

Caution: Do not attempt to play this CD-ROM in an audio player.

The Owner’s Manual contained in the CD-ROM can be downloaded from the following website.

http://download.yamaha.com/

Do not use this unit within 22 cm (9 inches) of persons with a heart pacemaker implant or

defibrillator implant.

Caution

Do not touch the surface marked with this label.

The surface may become hot during operation.

En 3

1 To assure the finest performance, please read this manual carefully. Keep it in a safe place for future

reference.

2 Install this sound system in a well ventilated, cool, dry, clean place - away from direct sunlight, heat

sources, vibration, dust, moisture, and/or cold. For proper ventilation, allow the following minimum

clearances.

Top: 30 cm, Rear: 20 cm, Sides: 20 cm

3 Locate this unit away from other electrical appliances, motors, or transformers to avoid humming

sounds.

4 Do not expose this unit to sudden temperature changes from cold to hot, and do not locate this unit in

an environment with high humidity (i.e. a room with a humidifier) to prevent condensation inside

this unit, which may cause an electrical shock, fire, damage to this unit, and/or personal injury.

5 Avoid installing this unit where foreign object may fall onto this unit and/or this unit may be exposed

to liquid dripping or splashing. On the top of this unit, do not place:

– Other components, as they may cause damage and/or discoloration on the surface of this unit.

– Burning objects (i.e. candles), as they may cause fire, damage to this unit, and/or personal injury.

– Containers with liquid in them, as they may fall and liquid may cause electrical shock to the user

and/or damage to this unit.

6 Do not cover this unit with a newspaper, tablecloth, curtain, etc. in order not to obstruct heat

radiation.

If the temperature inside this unit rises, it may cause fire, damage to this unit, and/or personal injury.

7 Do not plug in this unit to a wall outlet until all connections are complete.

8 Do not operate this unit upside-down. It may overheat, possibly causing damage.

9 Do not use force on switches, knobs and/or cords.

10 When disconnecting the power cable from the wall outlet, grasp the plug; do not pull the cable.

11 Do not clean this unit with chemical solvents; this might damage the finish. Use a clean, dry cloth.

12 Only voltage specified on this unit must be used. Using this unit with a higher voltage than specified

is dangerous and may cause fire, damage to this unit, and/or personal injury. Yamaha will not be

held responsible for any damage resulting from use of this unit with a voltage other than specified.

13 To prevent damage by lightning, keep the power cable and outdoor antennas disconnected from a

wall outlet or this unit during a lightning storm.

14 Do not attempt to modify or fix this unit. Contact qualified Yamaha service personnel when any

service is needed. The cabinet should never be opened for any reasons.

15 When not planning to use this unit for long periods of time (i.e. vacation), disconnect the AC power

plug from the wall outlet.

16 Be sure to refer to the “Troubleshooting” section of the Owner’s Manual on the CD-ROM for

common operating errors before concluding that this unit is faulty.

17 Before moving this unit, press z to set it to standby mode and disconnect the AC power plug from

the wall outlet.

18 VOLTAGE SELECTOR (Taiwan, Brazil and General models)

The VOLTAGE SELECTOR on the rear panel of this unit must be set for your local main voltage

BEFORE plugging into the AC wall outlet. Voltages are:

........................................................................................................... AC 110-120/220-240V, 50/60Hz

19 Condensation will form when the surrounding temperature changes suddenly. Disconnect the power

cable from the outlet, then leave this unit alone.

20 When using this unit for a long time, this unit may become warm. Turn the power off, then leave this

unit alone for cooling.

21 Install this unit near the AC outlet and where the AC power plug can be reached easily.

22 Excessive sound pressure from earphones and headphones can cause hearing loss.

■ Notes on remote controls and batteries

• Do not spill water or other liquids on the remote control.

• Do not drop the remote control.

• Do not leave or store the remote control in the following conditions:

– places of high humidity, such as near a bath

– places of high temperatures, such as near a heater or stove

– places of extremely low temperatures

– dusty places

• Insert the battery according to the polarity markings (+ and –).

• Change all batteries if you notice the following conditions:

– the operation range of the remote control narrows

– the transmit indicator does not flash or is dim

• If the batteries run out, immediately remove them from the remote control to prevent an explosion

or acid leak.

• If you find leaking batteries, discard the batteries immediately, taking care not to touch the leaked

material. If the leaked material comes into contact with your skin or gets into your eyes or mouth,

rinse it away immediately and consult a doctor. Clean the battery compartment thoroughly before

installing new batteries.

• Do not use old batteries together with new ones. This may shorten the life of the new batteries or

cause old batteries to leak.

• Do not use different types of batteries (such as alkaline and manganese batteries) together.

Specification of batteries may be different even though they look the same.

• Before inserting new batteries, wipe the compartment clean.

• If the remote control is without batteries for more than 2 minutes, or if exhausted batteries remain in

the remote control, the contents of the memory may be cleared. In such a case, install new batteries

and set the remote control code.

• Dispose of batteries according to your regional regulations.

• Keep batteries away from children. If a battery is accidentally swallowed, contact your doctor

immediately.

• When not planning to use the remote control for long periods of time, remove the batteries from the

remote control.

• Do not charge or disassemble the supplied batteries.

• The batteries shall not be exposed to excessive heat such as sunshine, fire or like.

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

This unit is not disconnected from the AC power source as long as it is connected to the wall outlet,

even if this unit itself is turned off by A. This state is called the standby mode. In this state, this unit

is designed to consume a very small quantity of power.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO

RAIN OR MOISTURE.

4 En

This document explains 7.1-channel system setup, 7.1.2-channel system

setup using the front presence speakers, and unit configuration, followed by

step-by-step instructions. Basic operations, such as playing Blu-ray Discs,

DVDs, and radio content, are also explained.

In this document, the RX-V3083 is used for illustration purposes. Some parts

or components, such as jacks or remote control keys, may vary by specific

model. Such differences are indicated as required.

The unit is equipped with a number of other functions not described in this

booklet. For more information about this product, refer to the Owner’s Manual

included on the supplied CD-ROM. The latest Owner’s Manual can be

downloaded from the following website.

http://download.yamaha.com/

The Owner’s Manual in HTML format can be viewed on your smartphone,

tablet, or PC. Visit the following website.

RX-V3083/RX-V2083

http://avpro.global.yamaha.com/manual/avr/rxv3083/

[For U.S. customers only]

Visit the following website for additional information, FAQ’s, downloads such

as “Owner’s Manual” and product updates.

http://usa.yamaha.com/support/

Opening and closing the front panel door

Press the bottom of the door gently to open it when using controls or jacks

behind the front panel door. Keep the door closed when controls or jacks

behind the front panel door are not in use. (Be careful not to trap your fingers.)

AV SETUP GUIDE

AV SETUP GUIDE is an app that guides you

through the process of connecting a TV or playback

device, such as a BD/DVD or CD player, and

speakers to the AV receiver. Search “AV SETUP

GUIDE” on the App Store or Google Play for

details.

En 5

1

Preparation

Confirming package contents

Preparing cables

The following cables (not supplied) are required to build the system described in this document.

• Speaker cables (depending on the number of speakers)

• Audio pin cable (x1)

• HDMI cables (x3)

• Network cable (x1) (when connecting to a router via a network cable)

Remote control

Batteries (AAA, R03, UM-4)

(x2)

CD-ROM (Owner’s Manual)

Quick Start Guide (this booklet)

YPAO microphone

AM antenna

(except for U.K., Europe, Australia

and Russia models)

Power cable

The supplied power cable varies

depending on the region of purchase.

FM antenna

(except for U.K., Europe, Australia

and Russia models)

One of the above is supplied depending

on the region of purchase.

DAB/FM antenna

(U.K., Europe, Australia and

Russia models)

Microphone base Pole

Use to measure angle/height

during YPAO.

6 En

2

Connecting speakers/subwoofer

When connecting 6-ohm speakers

Set the unit’s speaker impedance to “6 Ω MIN”. For details, see “Setting the

speaker impedance” in the Owner’s Manual.

Precautions for connecting speaker cables

• Be sure that the unit and subwoofer are turned off.

• Prepare speaker cables in a place away from the unit, to avoid accidentally

dropping wire strands into the unit's interior which could result in a short

circuit or malfunction of the unit.

• Improper connection of speaker cables could cause a short circuit resulting

in damage to, or malfunctioning of, the unit or speakers.

– Carefully remove approximately 10 mm

(3/8") of insulation from the speaker-

connection ends of the cables, and twist

the bare wires of each speaker cable

together firmly.

– Do not allow the bare wires of separate speaker

cables to come into contact with one another.

– Do not allow speaker cable bare wires to come into

contact with metal parts on the unit (rear panel and

screws).

If “Check SP Wires” is shown on the front display when the unit is turned on,

turn off the unit and be sure that speaker cables have not caused a short

circuit.

Positioning speakers

Use the diagram as a reference for positioning speakers.

1 Front speaker (L)

2 Front speaker (R)

3 Center speaker

4 Surround speaker (L)

5 Surround speaker (R)

6 Surround back speaker (L)

7 Surround back speaker (R)

E Front presence speaker (L)*

R Front presence speaker (R)*

9 Subwoofer

* For 7.1.2-channel system

*

RE

3

1

2

9

54

76

10° to 30° 10° to 30°

0.5 to 1 m

(1.6 to 3.3 ft)

0.5 to 1 m

(1.6 to 3.3 ft)

1.8 m

(5.9 ft)

1.8 m

(5.9 ft)

0.3 m (1 ft)

or more

10 mm

(3/8")

En 7

R L R L

R

L

4321

R

5

6

L R RL L

B

A

R

L

CENTER FRONT

R L R L

ZONE 2/ZONE 3/BI-AMP

F.PRESENCE

EXTRA SP1

1

2

SPEAKERS

SURROUND BACK

SURROUND

R.PRESENCE

R L R RL L

SINGLE

ZONE 2/ZONE 3/F.PRESENCE

PRE OUT

(REAR)

SUBWOOFER

CENTERFRONT

SURROUND SUR. BACK

(SINGLE) (FRONT)

EXTRA SP2

2

34

1

Subwoofer

9

2

Front speaker (R)

10 mm

(3/8")

1

Front speaker (L)

3

Center speaker

Surround speaker (R)

5

Surround speaker (L)

4

Use a subwoofer equipped

with built-in amplifier.

Audio pin cable

R

Front presence speaker (R)

E

Front presence speaker (L)

For 7.1.2-channel system

Surround back speaker (R)

7

Surround back speaker (L)

6

8 En

3

Connecting external devices

R L R L

R

L

4321

R

5

6

L R RL L

B

A

R

L

HDMI

HDMI HDMI

HDMI OUT

ARC

(ZONE OUT)

1

2

HDMI

(1 BD/DVD)

AV 1 AV 2 AV 3 AV 4

(HDCP2.2)

AV 5 AV 6 AV 7

(HDCP2.2)

HDMI HDMI HDMI

HDMI

TV BD/DVD player Satellite/cable set top box

HDMI input

HDMI output HDMI output

En 9

4

Connecting the radio antennas

FM/AM antennas (except for U.K., Europe,

Australia and Russia models)

DAB/FM antenna (U.K., Europe, Australia and

Russia models)

R L R L

R

L

4321

R

5

6

L R RL L

B

A

R

L

FM antenna (supplied) AM antenna (supplied)

Hold down Insert Release

Assembling the AM antenna

Place the AM

antenna on a

flat surface.

Fix the end of the

FM antenna to a

wall.

R L R L

R

L

4321

R

5

6

L R RL L

B

A

R

L

DAB/FM antenna (supplied)

Fix the antenna

ends to a wall.

10 En

5

Preparing a network connection

Prepare a wired or wireless network connection in accordance with your network environment.

Note

The wireless antenna must be raised if the unit will be connected to a Bluetooth device.

R L R L

R

L

4321

R

5

6

L R RL L

B

A

R

L

NETWORK

( 3

NET

)

LAN

Raise the wireless

antenna so that it is

standing up straight.

(Procedures for

connecting the unit to a

wireless router are

described in step

7

.)

Notice

Do not apply excessive force

on the antenna. Doing so

may damage it.

Wireless network connection

Internet

Network cable

Router Modem

Wired network connection

En 11

6

Connecting the power cable to an AC wall outlet,

and turning on the unit

1 Plug the power cable into an

AC wall outlet.

2 Press RECEIVER z to turn on

the unit.

3 Turn on the TV and switch the

TV input to display video from

the unit (HDMI OUT jack).

The Network Setup screen shown below will be

displayed on the TV when the unit is turned on for

the first time after purchase. It may take several

tens of seconds for the screen to be displayed

(WAC: Wireless Accessory Configuration).

See “Sharing the iOS device setting” under

“Connecting the unit to a wireless network” in the

Owner’s Manual when using this function to

connect the unit to a network.

This document explains wireless connection

using methods other than this function. Follow

the procedure described under “Connecting the

unit to a network” on the next page.

Note

This screen will not be displayed if the unit is connected

to a router via its NETWORK jack (wired connection).

Before connecting the power cable

(Taiwan, Brazil and General models only)

Set the switch position of VOLTAGE

SELECTOR according to your local voltage.

Voltages are AC 110–120/220–240 V,

50/60 Hz.

R L R L

R

L

4321

R

5

6

L R RL L

B

A

R

L

VOLTAGE SELECTOR

220V-

240V

110V-

120V

AC IN

To an AC

wall outlet

VOLTAGE SELECTOR

(Taiwan, Brazil and General models only)

4321

AUD IO

2 431

6 75

AV

V-AU X

BLUETOOTH

NET

USB

PHONO

TUNER

MAIN 234

HDMI OUTPART Y

RECEIVER

SOURCE

4

3

2

1

AUD

I

O

2

4

3

1

6

7

5

AV

V

-A

UX

B

L

U

ET

OO

TH

N

ET

US

B

PH

O

N

O

TU

NER

MAIN

2

3

4

HDMI OUT

PART Y

S

OURC

E

z

12 En

7

Connecting the unit to a network

Connecting the unit to a wireless network

• The unit can be connected to a wireless network using the MusicCast

CONTROLLER app* installed on your smartphone or other mobile device.

Follow procedure

A .

• If a mobile device will not be used, follow procedure

B to connect the unit

to a wireless router (access point) that supports WPS. Refer to the Owner’s

Manual for details on other wireless connection methods.

Connecting the unit to a router via a network cable

• Follow procedure

A to use the MusicCast CONTROLLER app* installed on

your smartphone or other mobile device to connect to the MusicCast

network to play music over a network.

• If a mobile device will not be used, skip this step and proceed to step

8

.

* MusicCast CONTROLLER, an app for mobile devices, can be used to

easily configure network settings for not only this unit, but also for other

MusicCast-enabled devices. This app allows you to listen to music stored

on your smartphone or other mobile device, or on servers, and to listen to

Internet radio stations. It also allows you to play this rich variety of music

content on all devices in the MusicCast network at the same time.

Visit the following website for details.

http://www.yamaha.com/musiccast/

A Connecting with the MusicCast

CONTROLLER app

Connect the unit to a network and register it as a MusicCast-enabled device.

Note

• Confirm that your mobile device is connected to your home router before beginning.

• You will need the router’s SSID and security key to connect the unit to a wireless

network.

• The MusicCast CONTROLLER app screens in this section show the English

interface. The screen appearance may vary depending on the app version.

1 Install the MusicCast CONTROLLER app on

your mobile device, and open the app.

Search for “MusicCast CONTROLLER” on the App Store or Google Play.

2 Tap “Setup”.

En 13

3 Confirm that the unit is turned on, and tap “Next”.

4 Press and hold the CONNECT button on the front

panel of the unit for 5 seconds, as instructed by

the app.

5 Follow the app’s on-screen instructions to

configure network settings.

When a connection has been established, “Completed” will be displayed

in the front display of the unit.

Network connection with the MusicCast CONTROLLER app is now complete,

and the unit has been registered as a MusicCast-enabled device.

B Using WPS push-button

configuration

Wireless connection can be configured with one push of the WPS button on

the wireless router (access point).

1 Press and hold INFO (WPS) on the unit’s front

panel for more than 3 seconds.

“Press WPS button on Access Point” will be displayed in the front display.

2 Push the WPS button on the wireless router.

When a connection has been established, “Completed” will be displayed

in the front display.

Note

If “Not connected” is displayed, repeat the process from step 1 or try another

connection method.

ENTER

OPTION

ON SCREEN

DISPLAYRETURN

YPAO MIC

PHONES

USB

SILENT CINEMA

TONE CONTROL

STRAIGHT

PROGRAM

MULTI ZONE

VIDEO AU

X

ZONE 2

ZONE 3

ZONE 4

ZONE CONTROL

5V

1A

SCENE

1234

RL AUDIO

(

CONNECT

)

MULTI ZONE

VIDEO AUX

ZONE 2

ZONE 3

ZONE 4

ZONE CONTROL

SCENE

1234

RL AUDIO

HDMI IN

INFO

(

WPS

)

MEMORY

FM AM

TUNING

PRESET

14 En

8

Optimizing the speaker settings automatically

(YPAO)

The Yamaha Parametric room Acoustic Optimizer (YPAO) function detects speaker connections, measures the distances from them to your listening position(s),

and then automatically optimizes the speaker settings, such as volume balance and acoustic parameters, to suit your room.

YPAO MIC

12

3

9

54

ER

ENTER

RETURN

POP-UP/MENU

TOP MENU

INPUT

MUTE

TV VOL TV CH

TV

4321

8765

9 0

41 2 3

MUTE

OPTION

ON

SCREEN

DISPLAY

MODE

MOVIE MUSIC

INFO SLEEP

ENT

PRESETTUNING

VOLUME

PROGRAM

BAND

SUR. DECODE

STRAIGHT

ENHANCER PURE DIRECT

10

MEMORY

CODE SET

RETURN

P

O

P-UP

/

MEN

U

T

OP MEN

U

INPUT

MU

TE

TV

V

O

V

L

T

V CH

TV

4

3

2

1

8

7

6

5

9

0

4

1

2

3

MU

T

E

OPTION

O

N

SC

REEN

D

I

S

PLAY

MO

DE

M

OVIE MUSIC

I

NF

O

S

LEEP

ENT

P

RE

S

E

T

TU

NIN

G

VO

LUME

P

R

OG

RAM

BAND

S

UR. DE

CO

D

E

STRAIGH

T

ENHAN

C

ER

PU

RE DIRE

CT

10

MEM

O

R

Y

CO

DE

S

E

T

ENTER

Note the following regarding

YPAO measurement

• Test tones are output at high

volume and may surprise or

frighten small children.

• Test tone volume cannot be

adjusted.

• Keep the room as quiet as

possible.

• Stay in a corner of the room

behind the listening position

so that you do not become an

obstacle between speakers

and the YPAO microphone.

• Do not connect headphones.

Ear height

Listening position

YPAO microphone

Cursor keys

En 15

1 Turn on the subwoofer and set the volume to half.

If the crossover frequency is adjustable, set it to maximum.

2 Place the YPAO microphone at your listening

position and connect it to the YPAO MIC jack on

the front panel.

The screen below appears on the TV.

Note

Place the YPAO microphone at your listening position (same height as your ears).

We recommend the use of a tripod as a microphone stand. You can use the tripod

screws to stabilize the microphone.

3 Use the cursor keys to select “Measure” and press

ENTER.

The measurement will start in 10 seconds.

It takes about 3 minutes to measure.

The screen below appears on the TV when the measurement finishes.

Note

If an error message (such as E-1) or warning message (such as W-2) appears,

see “Error messages” or “Warning messages” under “Optimizing the speaker

settings automatically (YPAO)” in the Owner’s Manual.

4 Use the cursor keys to select “Save/Cancel” and

press ENTER.

5 Use the cursor keys to select “SAVE” and press

ENTER.

6 Use the cursor keys to select “YES” to enable

YPAO Volume and press ENTER.

7 Disconnect the YPAO microphone from the unit.

This completes optimization of the speaker settings.

VOLUME

CROSSOVER/

HIGH CUT

MIN MAX

16 En

Basic operations

This section describes basic operations such as playing Blu-ray Discs and DVDs, and tuning into radio stations. Most operations can be performed using the

remote control.

Operating the remote control

POP-UP/MENU

TOP MENU

4321

AUD IO

2 431

6 75

AV

V-AU X

BLUETOOTH

NET

USB

PHONO

TUNER

MAIN

ZONE

234

41 2 3

SCENE

MUTE

VOLUME

PROGRAM

HDMI OUTPART Y

RECEIVER

SOURCE

POP-UP/MENU

MAIN

ZONE

2

3

4

PROGRAM

HDMI OUT

PART Y

SOURCE

MODE

MOVIE MUSIC

INFO SLEEP

PRESETTUNING

SUR. DECODE

STRAIGHT

ENHANCER PURE DIRECT

MODE

INFO

SLEEP

TUNING

The unit is equipped with a variety of sound

programs and surround decoders that allow you to

enjoy playback sources in your favorite sound

mode.

STRAIGHT: Input sources will be played without any

sound field effects.

PURE DIRECT: Input sources will be played using only

those functions absolutely vital to playback to minimize

noise generated by electronic circuitry. Functions such

as the front panel display will be temporarily disabled to

achieve Hi-Fi sound quality.

ENHANCER: Compressed music stored on a

Bluetooth device or USB storage device will be played

with additional depth and breadth.

MOVIE, MUSIC, SUR. DECODE: Sound programs

suitable for movies and music can be selected using

MOVIE or MUSIC, and unprocessed multichannel

playback from 2-channel sources is enabled using

SUR. DECODE.

Unit input sources and settings that have been

assigned to SCENE keys can be selected with just

one touch (SCENE function).

The unit turns on automatically when it is in standby

mode. By default, the following settings assigned to

each SCENE key.

SCENE key

Input AV1 AUDIO1

NET

RADIO

TUNER

Audio Select Auto Auto — —

Sound program Sci-Fi

STRAIGHT

9ch Stereo 9ch Stereo

Compressed

Music Enhancer

OffOnOnOn

Pure Direct Mode Auto Auto Auto Auto

Enhancer

Hi-Res Mode

On On On On

HDMI output jack

HDMI OUT

1+2

HDMI OUT

1+2

HDMI OUT

1+2

HDMI OUT

1+2

1

2

3

4

Mute the audio output

Adjust the volume level

Select an input source

Turn on/off (standby) the unit

En 17

Playing a BD/DVD

We recommend playing back multichannel audio (5.1-

channel or more) to feel surround sound produced by

the unit.

1 Turn on the BD/DVD player.

2 Press AV 1.

The name of the connected device such as “BD

player” may be displayed.

3 Start playback on the BD/DVD

player.

4 Press STRAIGHT to select

“STRAIGHT”.

Note

When “STRAIGHT” (straight decode) is enabled, each

speaker produces each channel audio signal directly

(without sound field processing).

5 Press VOLUME to adjust the

volume.

Note

When sound is not heard, or no sound is output from a specific

speaker, see “Troubleshooting” in the Owner’s Manual.

Listening to FM/AM radio

(except for U.K., Europe, Australia and

Russia models)

1 Press TUNER to select “TUNER” as

the input source.

2 Press BAND to select FM or AM.

3 Use the following keys to set a

frequency.

TUNING: Increase/decrease the frequency. Hold

down the key for about a second to search stations

automatically.

Numeric keys: Enter a frequency directly. For

example, to select 98.50 MHz, press “9”, “8”, “5”

and “0” (or ENT).

“TUNED” lights up when the unit is receiving an FM/

AM radio station signal.

“STEREO” lights up when the unit is receiving a

stereo FM radio signal.

Blu-ray

STRAIGHT

VOL.

SL

SW

SR

FPL

CL R

FPR

OUT

1

IN

AV1

Input source Device name

FM 98.50MHz

VOL.

SBL SBR

SL SR

CL R

STEREO TUNED

SW1

ENTER

RETURN

POP-UP/MENU

TOP MENU

INPUT

MUTE

TV VOL TV CH

TV

4321

AUD IO

2 431

6 75

AV

V-AU X

BLUETOOTH

NET

USB

PHONO

TUNER

4321

8765

9 0

MAIN

ZONE

234

41 2 3

SCENE

MUTE

OPTION

ON

SCREEN

DISPLAY

MODE

MOVIE MUSIC

INFO SLEEP

ENT

PRESETTUNING

VOLUME

PROGRAM

HDMI OUTPART Y

BAND

SUR. DECODE

STRAIGHT

ENHANCER PURE DIRECT

10

MEMORY

CODE SET

RECEIVER

SOURCE

ENTER

RETURN

P

O

P-

U

P

/

MEN

U

TO

P MEN

U

INPUT

M

UTE

TV

V

O

VV

L

T

V

C

H

TV

4

3

2

1

AUD

I

O

2

4

3

6

7

5

AV

V

-A

UX

B

L

U

ET

OO

TH

NET

US

B

PH

O

N

O

MAIN

Z

O

N

E

2

3

4

1

2

3

SCENE

MUTE

O

PTI

O

N

O

N

SC

REEN

D

ISPLAY

MO

DE

MO

VIE M

US

I

C

I

NF

O

S

LEEP

P

RE

S

E

T

P

R

OG

RAM

H

DMI

O

U

T

PART Y

SUR. DECODE

E

NHAN

C

ER

P

URE DIRE

CT

C

ODE SE

T

RECEIVE

R

SOU

R

CE

VOLUME

( / )

AV 1

STRAIGHT

TUNER

BAND

TUNING

Numeric

keys

18 En

Listening to DAB radio

(U.K., Europe, Australia and Russia

models)

1 Press TUNER to select “TUNER” as

the input source.

2 Press BAND to select the DAB

band.

The following message appears on the front panel if

you have not performed an initial scan yet.

3 Press ENTER to start an initial scan.

When the initial scan finishes, the unit automatically

tunes into the first DAB radio station as stored in

station order.

4 Press TUNING repeatedly to select

a DAB radio station.

Listening to Internet radio

1 Press NET repeatedly to select

“NET RADIO” as the input source.

The browse screen is displayed on the TV.

2 Use the cursor keys to select an

item and press ENTER.

When an Internet radio station is selected, playback

starts and the playback screen is displayed.

Note

Internet radio stations can also be selected using the

MusicCast CONTROLLER app installed on your mobile device.

Setting the frequency steps (Asia and General

models only)

At the factory, the frequency step setting is set to 50 kHz

for FM and 9 kHz for AM.

Depending on your country or region, set the frequency

steps to 100 kHz for FM and 10 kHz for AM.

1 Set the unit to standby mode.

2 Hold down STRAIGHT on the front panel and press

MAIN ZONE z.

3 Press PROGRAM on the front panel repeatedly to

select “TUNER FRQ STEP”.

4 Press STRAIGHT on the front panel to select

“FM100/AM10”.

5 Press MAIN ZONE z to set the unit to standby mode

and turn it on again.

FM50/AM9

TUNER FRQ STEP

Press

[ENTER]

Init Scan

VOL.

The MusicCast CONTROLLER app installed on

your mobile device can be used to play music from

streaming services. Refer to documentation

included on the supplied CD-ROM for more

information.

>>>-------

30%

Init Scan

VO L.

BBC Radio 4

DAB

VOL.

SL

SW

SR

CL R

SBL SBR

SW1

ENTER

RETURN

POP-UP/MENU

TOP MENU

INPUT

MUTE

TV VOL TV CH

TV

4321

AUD IO

2 431

6 75

AV

V-AU X

BLUETOOTH

NET

USB

PHONO

TUNER

4321

8765

9 0

MAIN

ZONE

234

41 2 3

SCENE

MUTE

OPTION

ON

SCREEN

DISPLAY

MODE

MOVIE MUSIC

INFO SLEEP

ENT

PRESETTUNING

VOLUME

PROGRAM

HDMI OUTPART Y

BAND

SUR. DECODE

STRAIGHT

ENHANCER PURE DIRECT

10

MEMORY

CODE SET

RECEIVER

SOURCE

RETURN

P

O

P-

U

P

/

MEN

U

TO

P MEN

U

INPUT

M

UTE

TV

V

O

VV

L

T

V

C

H

TV

4

3

2

1

AUD

I

O

2

4

3

1

6

7

5

AV

V

-A

UX

B

L

U

ET

OO

TH

US

B

PH

O

N

O

4

3

2

1

8

7

6

5

9

0

MAIN

Z

O

N

E

2

3

4

1

2

3

SCENE

MUTE

O

PTI

O

N

O

N

SC

REEN

D

ISPLAY

MO

DE

MO

VIE M

US

I

C

I

NF

O

S

LEEP

ENT

P

RE

S

E

T

VO

L

U

M

E

P

R

OG

RAM

H

DMI

O

U

T

PART Y

SUR. DECODE

S

TRAI

G

H

T

E

NHAN

C

ER

P

URE DIRE

CT

1

0

MEMOR

Y

C

ODE SE

T

RECEIVE

R

SOU

R

CE

NET

TUNER

BAND

TUNING

ENTER

Cursor

keys

En 19

Playing music stored on a

Bluetooth

®

device

1 Press BLUETOOTH to select

“Bluetooth” as the input source.

2 Select the unit (network name of the

unit) from the available device list

on the Bluetooth device.

If the pass key is required, enter the number “0000”.

When the connection is established, the

indicator will glow in the front display.

3 Select a song and start playback on

the Bluetooth device.

Note

Audio playing on the unit can be transmitted to Bluetooth

wireless speakers or headphones (except when Bluetooth is

selected as the unit’s input source). See “Enjoying audio using

Bluetooth speakers/headphones” in the Owner’s Manual for

more information.

Playing music stored on a

USB flash drive

1 Connect the USB flash drive to the

USB jack.

Note

Connect the USB flash drive directly to the USB jack. Do

not use an extension cable.

2 Press USB to select “USB” as the

input source.

The browse screen is displayed on the TV.

3 Use the cursor keys to select an

item and press ENTER.

When a song is selected, playback starts and the

playback screen is displayed.

ENTER

DISPLAYRETURN

YPAO MIC

PHONES

USB

SILENT CINEMA

PROGRAM

MULTI ZON

ZONE 2

ZONE 3

ZO

N

5V

1A

RL AUDIO

(

CONNECT

)

USB flash drive

ENTER

RETURN

POP-UP/MENU

TOP MENU

INPUT

MUTE

TV VOL TV CH

TV

4321

AUD IO

2 431

6 75

AV

V-AU X

BLUETOOTH

NET

USB

PHONO

TUNER

4321

8765

9 0

MAIN

ZONE

234

41 2 3

SCENE

MUTE

OPTION

ON

SCREEN

DISPLAY

MODE

MOVIE MUSIC

INFO SLEEP

ENT

PRESETTUNING

VOLUME

PROGRAM

HDMI OUTPART Y

BAND

SUR. DECODE

STRAIGHT

ENHANCER PURE DIRECT

10

MEMORY

CODE SET

RECEIVER

SOURCE

RETURN

P

O

P-

U

P

/

MEN

U

TO

P MEN

U

INPUT

M

UTE

TV

V

O

VV

L

T

V

C

H

TV

4

3

2

1

AUD

I

O

2

4

3

1

6

7

5

AV

V

-A

UX

NET

PH

O

N

O

T

UNER

4

3

2

1

8

7

6

5

9

0

MAIN

Z

O

N

E

2

3

4

1

2

3

SCENE

MUTE

O

PTI

O

N

O

N

SC

REEN

D

ISPLAY

MO

DE

MO

VIE M

US

I

C

I

NF

O

S

LEEP

ENT

P

RE

S

E

T

UNIN

G

VO

L

U

M

E

P

R

OG

RAM

H

DMI

O

U

T

PART Y

B

AN

D

SU

R. DE

CO

D

E

S

TRAI

G

H

T

E

NHAN

C

ER

P

URE DIRE

CT

1

0

MEMOR

Y

C

ODE SE

T

RECEIVE

R

SOU

R

CE

USB

BLUETOOTH

ENTER

Cursor

keys

20 Zh

产品中有害物质的名称及含量

本表格依据 SJ/T 11364 的规定编制。

○：表示该有害物质在该部件所有均质材料中的含量均在 GB/T 26572 规定的

限量要求以下。

×：表示该有害物质至少在该部件的某一均质材料中的含量超出 GB/T 26572

规定的限量要求。

中文

z （电源）键

打开本机的电源或将其设置为待机模式。

本产品适用于普通家庭。请勿用于需要高可靠性的应用，例如管理生命、医

疗保健或高价值资产。

有关详情，请参见 CD-ROM 上的使用说明书。

要查看使用说明书，请单击当 CD-ROM 插入 PC 时自动显示的屏幕中的

“ 中文 ”，或在显示型号选择屏幕的情况下单击相应型号，然后单击下一

屏幕中的 “ 中文 ”。之后，请遵照屏幕说明进行操作。

如果未自动显示相应屏幕，请打开 CD-ROM 中的 “index.html” 文件。

警告：切勿试图在音频播放机中播放此 CD-ROM。

此标识适用于在中华人民共和国销售的电子信息产品。

标识中间的数字为环保使用期限的年数。

部件名称

有害物质

铅

(Pb)

汞

(Hg)

镉

(Cd)

六价铬

(Cr(VI))

多溴联苯

(PBB)

多溴二苯醚

(PBDE)

电路板 × ○ ○ ○ ○ ○

外壳箱体 × ○ ○ ○ ○ ○

前部面板显示器 × ○ ○ ○ ○ ○

ページが読み込まれています...

Yamaha RX-V2083 クイックスタートガイド

このマニュアルも適しています

Yamaha RX-V2083 クイックスタートガイド

他の言語で

関連論文

その他のドキュメント