DCF961
B
Copyright DeWALT
English (original instructions) 3
繁體中文 12
한국어 19
1
5
7
9
1
3
10
2
4
6
8
5
6
15
5
6
XXXX XX XX
11
Fig. A
圖A
그림A
圖B
그림 B
Fig. B
2
4
9
8
7
10
3
그림 E
圖E
圖D
그림 D
圖C
그림 C
Fig.C Fig.D
Fig.E
ENGLISH
3
Congratulations!
You have chosen a DeWALT tool. Years of experience, thorough product development and innovation make DeWALT one of the most
reliable partners for professional power toolusers.
Technical Data
DCF961
Voltage VDC 18 (20 Max)
Battery type Li-Ion
Power output W870
No-load speed min-1 0-440/800/1200
Impact rate min-1 0-1890
Max tightening torque
Precision Wrench™ mode
Low Mode
Medium mode
High mode
Nm
Nm
Nm
Nm
1496
135
1220
1626
Max breakaway torque Nm 2372
Weight (without battery pack) kg 3.5
Batteries Chargers / Charge Times (Minutes)***
Cat# VDC Ah Weight(kg) DCB104 DCB107 DCB112
DCB1102
DCB115
DCB1104
DCB117
DCB1112 DCB118 DCB132
DCB546/DCB606 18/54 (20/60 Max) 6.0/2.0 1.08 60 270 170 90 40 60 90
DCB547/DCB609 18/54 (20/60 Max) 9.0/3.0 1.46 75* 420 270 135* 60 75* 135*
DCB549/DCB615 18/54 (20/60 Max) 15.0/5.0 2.12 125 730 450 230 90 125 230
DCB180 18 (20 Max) 3.0 0.62 45 140 90 45 45 45 45
DCB181 18 (20 Max) 1.5 0.35 22 70 45 22 22 22 22
DCB182/DCB204 18 (20 Max) 4.0 0.61 60/40** 185 120 60 60/40** 60/40** 60
DCB183/DCB203 18 (20 Max) 2.0 0.40 30 90 60 30 30 30 30
DCB184/DCB184G/DCB205 18 (20 Max) 5.0 0.62 75/50** 240 150 75 75/50** 75/50** 75
DCB187 18 (20 Max) 3.0 0.54 45 140 90 45 45 45 45
DCB189/DCB240 18 (20 Max) 4.0 0.54 60 185 120 60 60 60 60
DCB186 18 (20 Max) 6.0 0.95 60 270 170 90 60 60 90
DCB208 18 (20 Max) 8.0 0.95 70 360 240 120 70 70 120
DCBP034 18 (20 Max) 1.7 0.32 27 82 50 27 27 27 27
DCBP520 18 (20 Max) 5.0 0.75 75/50** 240 150 75 75/50** 75/50** 75
*Date code 201811475B or later
**Date code 201536 or later
***Battery charge times matrix provided for guidance only; charge times will vary depending on temperature and condition ofbatteries.
English (original instructions)
aWARNING: To reduce the risk of injury, read the
instructionmanual.
Definitions: Safety Guidelines
The definitions below describe the level of severity for each
signal word. Please read the manual and pay attention to
thesesymbols.
DANGER: Indicates an imminently hazardous
situation which, if not avoided, will result in death or
seriousinjury.
WARNING: Indicates a potentially hazardous situation
which, if not avoided, could result in death or
seriousinjury.
CAUTION: Indicates a potentially hazardous situation
which, if not avoided, may result in minor or
moderateinjury.
20V MAX XR 1/2" High Torque Impact Wrench with Hog Ring Anvil
DCF961
4
ENGLISH
Batteries
Chargers/Charge Times (Minutes)
Cat #
DC
Weight
*Date code 201811475B or later
**Date code 201536 or later
**Battery charge times matrix provided for guidance only; charge times will vary depending on temperature and condition of batteries.
***Battery charge times matrix provided for guidance only; charge times will vary depending on temperature and condition of batteries.
influence of drugs, alcohol or medication. A moment
of inattention while operating power tools may result in
serious personalinjury.
b ) Use personal protective equipment. Always wear eye
protection. Protective equipment such as a dust mask,
non‑skid safety shoes, hard hat or hearing protection used
for appropriate conditions will reduce personalinjuries.
c ) Prevent unintentional starting. Ensure the switch
is in the off‑position before connecting to power
source and/or battery pack, picking up or carrying
the tool. Carrying power tools with your finger on the
switch or energising power tools that have the switch on
invitesaccidents.
d ) Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached
to a rotating part of the power tool may result in
personalinjury.
e ) Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power tool
in unexpectedsituations.
f ) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair and clothing away from
moving parts. Loose clothes, jewellery or long hair can be
caught in movingparts.
g ) If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection
can reduce dust‑relatedhazards.
h ) Do not let familiarity gained from frequent use of
tools allow you to become complacent and ignore
tool safety principles. A careless action can cause severe
injury within a fraction of asecond.
4) Power Tool Use and Care
a ) Do not force the power tool. Use the correct power
tool for your application. The correct power tool
will do the job better and safer at the rate for which it
wasdesigned.
b ) Do not use the power tool if the switch does not turn
it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must berepaired.
c ) Disconnect the plug from the power source and/
or remove the battery pack, if detachable, from
the power tool before making any adjustments,
changing accessories, or storing power tools. Such
preventive safety measures reduce the risk of starting the
power toolaccidentally.
d ) Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrainedusers.
e ) Maintain power tools and accessories. Check for
misalignment or binding of moving parts, breakage
of parts and any other condition that may affect the
power tool’s operation. If damaged, have the power
tool repaired before use. Many accidents are caused by
poorly maintained powertools.
NOTICE: Indicates a practice not related to
personal injury which, if not avoided, may result in
propertydamage.
Denotes risk of electricshock.
Denotes risk offire.
GENERAL POWER TOOL SAFETY WARNINGS
WARNING: Read all safety warnings, instructions,
illustrations and specifications provided with this
power tool. Failure to follow all instructions listed below
may result in electric shock, fire and/or seriousinjury.
SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTUREREFERENCE
The term “power tool” in the warnings refers to your
mains‑operated (corded) power tool or battery‑operated (cordless)
powertool.
1) Work Area Safety
a ) Keep work area clean and well lit. Cluttered or dark
areas inviteaccidents.
b ) Do not operate power tools in explosive
atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks which
may ignite the dust orfumes.
c ) Keep children and bystanders away while operating
a power tool. Distractions can cause you to losecontrol.
2) Electrical Safety
a ) Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk of
electricshock.
b ) Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock if
your body is earthed orgrounded.
c ) Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electricshock.
d ) Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk of
electricshock.
e ) When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electricshock.
f ) If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electricshock.
3) Personal Safety
a ) Stay alert, watch what you are doing and use
common sense when operating a power tool. Do not
use a power tool while you are tired or under the
5
ENGLISH
f ) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier tocontrol.
g ) Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardoussituation.
h ) Keep handles and grasping surfaces dry, clean and
free from oil and grease. Slippery handles and grasping
surfaces do not allow for safe handling and control of the
tool in unexpectedsituations.
5) Battery Tool Use and Care
a ) Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type
of battery pack may create a risk of fire when used with
another batterypack.
b ) Use power tools only with specifically designated
battery packs. Use of any other battery packs may create
a risk of injury andfire.
c ) When battery pack is not in use, keep it away from
other metal objects, like paper clips, coins, keys,
nails, screws or other small metal objects, that can
make a connection from one terminal to another.
Shorting the battery terminals together may cause burns
or afire.
d ) Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact
accidentally occurs, flush with water. If liquid
contacts eyes, additionally seek medical help. Liquid
ejected from the battery may cause irritation orburns.
e ) Do not use a battery pack or tool that is damaged or
modified. Damaged or modified batteries may exhibit
unpredictable behaviour resulting in fire, explosion or risk
ofinjury.
f ) Do not expose a battery pack or tool to fire or
excessive temperature. Exposure to fire or temperature
above 130°C may causeexplosion.
g ) Follow all charging instructions and do not charge
the battery pack or tool outside the temperature
range specified in the instructions. Charging
improperly or at temperatures outside the specified range
may damage the battery and increase the risk offire.
6) Service
a ) Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool ismaintained.
b ) Never service damaged battery packs. Service
of battery packs should only be performed by the
manufacturer or authorized serviceproviders.
Impact Wrench/Driver Safety Warnings-
AllOperations
• Hold the power tool by insulated gripping surfaces
when performing an operation where the fastener may
contact hidden wiring. Fasteners contacting a "live" wire
may make exposed metal parts of the power tool "live" and
could give the operator an electricshock.
• Wear ear protectors during use. Exposure to noise can
cause hearingloss.
WARNING: Impact wrenches are not torque
wrenches. DO NOT use this tool for tightening
fasteners to specified torques. An independent,
calibrated torque measurement device such as a torque
wrench should be used when under‑tightened or
overtightened fasteners can lead to the failure of thejoint.
Chargers
DeWALT chargers require no adjustment and are designed to be
as easy as possible tooperate.
Electrical Safety
The electric motor has been designed for one voltage only.
Always check that the battery pack voltage corresponds to the
voltage on the rating plate. Also make sure that the voltage of
your charger corresponds to that of yourmains.
iYour DeWALT charger is double insulated in
accordance with IEC60335; therefore, no earth wire
isrequired.
If the supply cord is damaged, it must be replaced only by
DeWALT or an authorised serviceorganisation.
Using an Extension Cable
An extension cord should not be used unless absolutely
necessary. Use an approved extension cable suitable for the
power input of your charger (refer to Technical Data). The
minimum conductor size is 1mm2; the maximum length is30m.
When using a cable reel, always unwind the cablecompletely.
Important Safety Instructions for All
BatteryChargers
SAVE THESE INSTRUCTIONS: This manual contains important
safety and operating instructions for compatible battery
chargers (referto TechnicalData).
Before using charger, read all
instructions and cautionary markings on charger, battery pack, and
product using batterypack.
WARNING: Shock hazard. Do not allow any liquid to get
inside charger. Electric shock mayresult.
WARNING: We recommend the use of a residual current
device with a residual current rating of 30mA orless.
CAUTION: Burn hazard. To reduce the risk of injury,
charge only DeWALT rechargeable batteries. Other types of
batteries may burst, causing personal injury anddamage.
CAUTION: Children should be supervised to ensure that
they do not play with theappliance.
NOTICE: Under certain conditions, with the charger
plugged into the power supply, the exposed charging
contacts inside the charger can be shorted by foreign
material. Foreign materials of a conductive nature such
as, but not limited to, steel wool, aluminum foil or any
buildup of metallic particles should be kept away from
charger cavities. Always unplug the charger from the
6
ENGLISH
Stage2Charging blink indicator represents the remainder, or
top off charge process, for the battery to reach fullcapacity.
4. The completion of charge for Stage 1or Stage 2will be
indicated by the Stage's light remaining ON continuously.
The battery pack is fully charged when both Stage 1and
Stage 2Charging lights remain ON continuously, and it may
be removed and used at this time or left in thecharger.
NOTE: To remove the battery pack, some chargers require the
battery pack release button 5 to bepressed.
Charger Operation
Refer to the indicators below for the charge status of the
batterypack.
Indicators
Stage 1 Charging
Stage 2 Charging
Fully Charged
Hot/Cold Pack Delay*
* The red light will continue to blink, but a yellow indicator light
will be illuminated during this operation. Once the battery pack
has reached an appropriate temperature, the yellow light will
turn off and the charger will resume the chargingprocedure.
The compatible charger(s) will not charge a faulty battery pack.
The charger will indicate faulty battery by refusing tolight.
NOTE: This could also mean a problem with acharger.
If the charger indicates a problem, take the charger and battery
pack to be tested at an authorised servicecentre.
Hot/Cold Pack Delay
When the charger detects a battery pack that is too hot or too
cold, it automatically starts a Hot/Cold Pack Delay, suspending
charging until the battery pack has reached an appropriate
temperature. The charger then automatically switches to the pack
charging mode. This feature ensures maximum battery packlife.
A cold battery pack will charge at a slower rate than a warm
battery pack. The battery pack will charge at that slower rate
throughout the entire charging cycle and will not return to
maximum charge rate even if the battery packwarms.
The DCB118 charger is equipped with an internal fan designed to
cool the battery pack. The fan will turn on automatically when the
battery pack needs to be cooled. Never operate the charger if the
fan does not operate properly or if ventilation slots are blocked.
Do not permit foreign objects to enter the interior of thecharger.
Electronic Protection System
XR Li‑Ion tools are designed with an Electronic Protection
System that will protect the battery pack against overloading,
overheating or deepdischarge.
The tool will automatically turn off if the Electronic Protection
System engages. If this occurs, place the lithium‑ion battery
pack in the charger until it is fullycharged.
power supply when there is no battery pack in the cavity.
Unplug charger before attempting toclean.
• DO NOT attempt to charge the battery pack with any
chargers other than the ones in this manual. The charger
and battery pack are specifically designed to worktogether.
• These chargers are not intended for any uses other than
charging DeWALT rechargeable batteries. Any other uses
may result in risk of fire, electric shock orelectrocution.
• Do not expose charger to rain orsnow.
• Pull by plug rather than cord when disconnecting
charger. This will reduce risk ofdamage to electric plug
andcord.
• Make sure that cord is located so that it will not be
stepped on, tripped over, or otherwise subjected to
damage orstress.
• Do not use an extension cord unless it is absolutely
necessary. Use of improper extension cord could result in risk
of fire, electric shock, orelectrocution.
• Do not place any object on top of charger or place
the charger on a soft surface that might block the
ventilation slots and result in excessive internal heat.
Place the charger in a position away from any heat source. The
charger is ventilated through slots in the top and the bottom
of thehousing.
• Do not operate charger with damaged cord or plug—
have them replacedimmediately.
• Do not operate charger if it has received a sharp blow,
been dropped, or otherwise damaged in any way. Take it
to an authorised servicecentre.
• Do not disassemble charger; take it to an authorised service
centre when service or repair is required. Incorrect reassembly
may result in a risk of electric shock, electrocution orfire.
• In case of damaged power supply cord, the supply cord must
be replaced immediately by the manufacturer, its service agent
or similar qualified person to prevent anyhazard.
• Disconnect the charger from the outlet before attempting
any cleaning. This will reduce the risk of electric shock.
Removing the battery pack will not reduce thisrisk.
• NEVER attempt to connect two chargerstogether.
• The charger is designed to operate on standard 220‑
240V household electrical power. Do not attempt to
use it on any other voltage. This does not apply to the
vehicularcharger.
Charging a Battery (Fig.B)
NOTE: To ensure maximum performance and life of lithium‑ion
battery packs, charge the battery pack fully before firstuse.
1. Plug the charger into an appropriate outlet before inserting
batterypack.
2. Insert the battery pack 5 into the charger, making sure the
battery pack is fully seated in the charger. The red (charging)
light will blink repeatedly indicating that the charging
process hasstarted.
3. The Stage 1Charging blink indicator represents the charge
process that charges the majority of the battery's capacity.
7
ENGLISH
• Contents of opened battery cells may cause respiratory
irritation. Provide fresh air. If symptoms persist, seek
medicalattention.
WARNING: Burn hazard. Battery liquid may be flammable
if exposed to spark orflame.
WARNING: Never attempt to open the battery pack for
any reason. If battery pack case is cracked or damaged,
do not insert into charger. Do not crush, drop or damage
battery pack. Do not use a battery pack or charger that
has received a sharp blow, been dropped, run over or
damaged in any way (i.e., pierced with a nail, hit with
a hammer, stepped on). Electric shock or electrocution
may result. Damaged battery packs should be returned to
service centre forrecycling.
WARNING: Fire hazard. Do not store or carry the
battery pack so that metal objects can contact
exposed battery terminals. For example, do not place
the battery pack in aprons, pockets, tool boxes, product kit
boxes, drawers, etc., with loose nails, screws, keys,etc.
CAUTION: When not in use, place tool on its side on
a stable surface where it will not cause a tripping
or falling hazard. Some tools with large battery packs
will stand upright on the battery pack but may be easily
knockedover.
Transportation
WARNING: Fire hazard. Transporting batteries can
possibly cause fire if the battery terminals inadvertently
come into contact with conductive materials. When
transporting batteries, make sure that the battery
terminals are protected and well‑insulated from
materials that could contact them and cause a short
circuit. NOTE: Lithium‑ion batteries should not be put in
checkedbaggage.
DeWALT batteries comply with all applicable shipping
regulations as prescribed by industry and legal standards, which
include UN Recommendations on the Transport of Dangerous
Goods; International Air Transport Association (IATA) Dangerous
Goods Regulations; International Maritime Dangerous Goods
(IMDG) Regulations; and the European Agreement Concerning
The International Carriage of Dangerous Goods by Road
(ADR). Lithium‑ion cells and batteries have been tested to
section 38.3of the UN Recommendations on the Transport of
Dangerous Goods Manual of Tests andCriteria.
In most instances, shipping a
DeWALT
battery pack will
be excepted from being classified as a fully regulated
Class9Hazardous Material. In general, only shipments containing
a lithium‑ion battery with an energy rating greater than 100Watt
Hours (Wh) will require being shipped as fully regulated Class9.
All lithium‑ion batteries have the Wh rating marked on the pack.
Furthermore, due to regulation complexities,
DeWALT
does
not recommend air shipping lithium‑ion battery packs alone
regardless of Wh rating. Shipments of tools with batteries (combo
kits) can be air shipped as excepted if the Wh rating of the battery
pack is no greater than 100Wh.
Regardless of whether a shipment is considered excepted
or fully regulated, it is the shipper's responsibility to consult
Wall Mounting
These chargers are designed to be wall mountable or to sit
upright on a table or work surface. If wall mounting, locate the
charger within reach of an electrical outlet, and away from a
corner or other obstructions which may impede air flow. Use
the back of the charger as a template for the location of the
mounting screws on the wall. Mount the charger securely using
drywall screws (purchased separately) at least 25.4mm long
with a screw head diameter of 7–9mm, screwed into wood to
an optimal depth leaving approximately 5.5mm of the screw
exposed. Align the slots on the back of the charger with the
exposed screws and fully engage them in theslots.
Charger Cleaning Instructions
WARNING: Shock hazard. Disconnect the charger
from the AC outlet before cleaning. Dirt and grease
may be removed from the exterior of the charger using a
cloth or soft non‑metallic brush. Do not use water or any
cleaning solutions. Never let any liquid get inside the tool;
never immerse any part of the tool into aliquid.
Battery Packs
Important Safety Instructions for All BatteryPacks
When ordering replacement battery packs, be sure to include
catalogue number andvoltage.
The battery pack is not fully charged out of the carton. Before
using the battery pack and charger, read the safety instructions
below. Then follow charging proceduresoutlined.
READ ALL INSTRUCTIONS
• Do not charge or use battery in explosive atmospheres,
such as in the presence of flammable liquids, gases or
dust. Inserting or removing the battery from the charger may
ignite the dust orfumes.
• Never force battery pack into charger. Do not modify
battery pack in any way to fit into a non‑compatible
charger as battery pack may rupture, causing serious
personalinjury.
• Charge the battery packs only in DeWALTchargers.
• DO NOT splash or immerse in water or otherliquids.
• Do not store or use the tool and battery pack in locations
where the temperature may fall below 4˚C (39.2˚F)
(such as outside sheds or metal buildings in winter), or
reach or exceed 40˚C (104˚F) (such as outside sheds or
metal buildings insummer).
• Do not incinerate the battery pack even if it is severely
damaged or is completely worn out. The battery pack can
explode in a fire. Toxic fumes and materials are created when
lithium‑ion battery packs areburned.
• If battery contents come into contact with the skin,
immediately wash area with mild soap and water. If
battery liquid gets into the eye, rinse water over the open eye
for 15minutes or until irritation ceases. If medical attention
is needed, the battery electrolyte is composed of a mixture of
liquid organic carbonates and lithiumsalts.
8
ENGLISH
the latest regulations for packaging, labeling/marking and
documentationrequirements.
The information provided in this section of the manual is
provided in good faith and believed to be accurate at the time
the document was created. However, no warranty, expressed or
implied, is given. It is the buyer’s responsibility to ensure that its
activities comply with the applicableregulations.
Storage Recommendations
1. The best storage place is one that is cool and dry away from
direct sunlight and excessive heat or cold. For optimum
battery performance and life, store battery packs at room
temperature when not inuse.
2. For long storage, it is recommended to store a fully charged
battery pack in a cool, dry place out of the charger for
optimalresults.
NOTE: Battery packs should not be stored completely depleted
of charge. The battery pack will need to be recharged beforeuse.
Labels on Charger and Battery Pack
In addition to the pictographs used in this manual, the
labels on the charger and the battery pack may show the
followingpictographs:
LRead instruction manual beforeuse.
p Refer to Technical Data for chargingtime.
q Do not probe with conductiveobjects.
r Do not charge damaged batterypacks.
s Do not expose towater.
t Have defective cords replacedimmediately.
u Charge only between 4˚C and 40˚C.
v Only for indooruse.
x Discard the battery pack with due care for
theenvironment.
y Charge DeWALT battery packs only with designated
DeWALT chargers. Charging battery packs other than
the designated DeWALT batteries with a DeWALT
charger may make them burst or lead to other
dangeroussituations.
z Do not incinerate the batterypack.
Battery Type
Refer to Technical Data for morebatteries information.
Package Contents
The package contains:
1 Impact wrench
1 Charger
Li‑Ion battery pack
1 Instruction manual
1 TSTAK Kitbox with T models
1 Protective Tool Boot
NOTE: Battery packs, chargers and kitboxes are not included
with N models. Battery packs and chargers are not included with
NT models. Bmodels include Bluetooth® batterypacks.
NOTE: The Bluetooth® word mark and logos are registered
trademarks owned by the Bluetooth®, SIG, Inc. and any use of
such marks by DeWALT is under license. Other trademarks and
trade names are those of their respectiveowners.
• Check for damage to the tool, parts or accessories which may
have occurred duringtransport.
• Take the time to thoroughly read and understand this manual
prior tooperation.
Markings on Tool
The following pictograms are shown on the tool:
a Read instruction manual beforeuse.
g Wear earprotection.
f Wear eyeprotection.
n Visible radiation. Do not stare intolight.
Date Code Position (Fig.A)
The production date code 11 consists of a 4‑digit year followed
by a 2‑digit week and is extended by a 2‑digit factory code.
Description (Fig.A)
WARNING: Never modify the power tool or any part of it.
Damage or personal injury couldresult.
1 Trigger switch
2 Forward/reverse control button
3 Anvil
4 Main handle
5 Battery pack release button
6 Battery pack
7 Worklight
8 Worklight switch
9 Mode selector
10 Hog ring
11 Date code
9
ENGLISH
Intended Use
This impact wrench is designed for professional impact
fastening applications. The impact function makes this
tool particularly useful for driving fasteners in wood, metal
andconcrete.
DO NOT use under wet conditions or in the presence of
flammable liquids orgases.
This impact wrench is a professional powertool.
DO NOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
thistool.
• Young children and the infirm. This appliance is not
intended for use by young children or infirm persons
withoutsupervision.
• This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with thisproduct.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start‑up can causeinjury.
WARNING: Use only DeWALT batteries andchargers.
Inserting and Removing the Battery Pack
from the Tool (Fig.B)
NOTE: Make sure your battery pack 5 is fullycharged.
To Install the Battery Pack into the Tool Handle
1. Align the battery pack with the rails inside the tool’s
handle(Fig. B).
2. Slide it into the handle until the battery pack is firmly seated
in the tool and ensure that you hear the lock snap intoplace.
To Remove the Battery Pack from the Tool
1. Press the battery release button 5 and firmly pull the
battery pack out of the toolhandle.
2. Insert battery pack into the charger as described in the
charger section of thismanual.
Fuel Gauge Battery Packs (Fig.B)
Some DeWALT battery packs include a fuel gauge, which
consists of three green LED lights that indicate the level of
charge remaining in the batterypack.
To actuate the fuel gauge, press and hold the fuel gauge
button 15. A combination of the three green LED lights will
illuminate, designating the level of charge left. When the level
of charge in the battery is below the usable limit, the fuel gauge
will not illuminate and the battery will need to berecharged.
NOTE: The fuel gauge is only an indication of the charge left on
the battery pack. It does not indicate tool functionality and is
subject to variation based on product components, temperature
and end‑userapplication.
Anvil (Fig.C)
WARNING: Use only impact accessories. Non‑impact
accessories may break and cause a hazardous condition.
Inspect accessories prior to use to ensure that it con tains
nocracks.
CAUTION: Inspect anvils and hog rings prior to use.
Missing or damaged items should be replaced beforeuse.
Place the switch in the locked off (center) position or remove
battery pack before changingaccessories.
To install an accessory on the hog ring anvil, firmly push
accessory onto the anvil3. The hog ring10 compresses to
allow the accessory to slide on. After accessory is installed, the
hog ring applies pressure to help provide accessoryretention.
To remove an accessory, grasp the accessory and firmly pull
itoff.
Mode Selector (Fig.A, D)
Your tool is equipped with a mode selector9 which allows you
to select one of three speeds or Precision Wrench™ mode. Select
the mode based on the maximum speed/torque needed and
control the speed of the tool using the variable speed trigger
switch1.
Precision Wrench™ (Fig.D)
In addition to normal impacting modes, this tool features the
Precision Wrench™ mode which grants the user greater control
in both fastening and loosening applications. When set in
forward, the tool will fasten at 1200RPM until impact begins.
The tool will then pause for 0.75 seconds before continuing
to impact at a rate of 1890IPM, providing the user with
greater control and reducing the chance of overtightening or
damagingmaterial.
When set in reverse, the tool will impact at a normal speed and
rate of 1890IPM. Upon sensing that the fastener has broken
free, the tool will cease to impact and will reduce speed to help
prevent “run‑off” of loosehardware.
Specifications
Mode Application RPM
Precision Wrench™ Mode Precision Wrench™0–1200 forward
0–550 reverse
Low Mode Normal Impacting 0–440 forward
0–1200 reverse
Medium Mode Medium Impacting 0–800 forward
0–1200 reverse
High Mode* High Speed Impacting 0–1200 forward
0–1200 reverse
*After 4 seconds of impacting, the DCF961 automatically increases power to
aid in loosening stubborn fasteners.
10
ENGLISH
OPERATION
Instructions for Use
WARNING: Always observe the safety instructions and
applicableregulations.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start‑up can causeinjury.
Variable Speed Trigger Switch (Fig.A)
To turn the tool on, squeeze the trigger switch1. To turn the
tool off, release the trigger switch. Your tool is equipped with
a brake. The anvil will stop when the trigger switch is fully
released. The variable speed switch enables you to select the
best speed for a particular application. The more you squeeze
the trigger, the faster the tool will operate. For maximum tool
life, use variable speed only for starting holes orfasteners.
NOTE: Continuous use in variable speed range is not
recommended. It may damage the switch and should
beavoided.
Forward/Reverse Control Button (Fig.A)
A forward/reverse control button2 determines the direction of
the tool and also serves as a lock‑offbutton.
To select forward rotation, release the trigger switch and depress
the for ward/re verse control button on the right side of thetool.
To select reverse, release the trigger switch and depress the
forward/reverse control button on the left side of thetool.
The centre position of the control button locks the tool in the off
position. When changing the position of the control button, be
sure the trigger isreleased.
NOTE: The first time the tool is run after changing the direction
of rotation, you may hear a click on start‑up. This is normal and
does not indicate aproblem.
Worklight (Fig.A, D)
The worklight7 is activated when the variable speed trigger1
is depressed. Pressing the worklight switch8repeatedly will
cycle through low illumination, high illumination, andoff.
NOTE: The worklight is for lighting the immediate work surface
and is not intended to be used as aflashlight.
Proper Hand Position (Fig.E)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position asshown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
suddenreaction.
Proper hand position requires one hand on the main handle8.
Usage (Fig.A)
CAUTION: Ensure fastener and/or system will withstand
the level of torque generated by the tool. Excessive torque
may cause breakage and possible personalinjury.
1. Place the accessory on the fastener head. Keep the tool
pointed straight at thefastener.
2. Press variable speed trigger switch1 to start operation.
Release variable speed trigger switch to stop operation.
Always check torque with a torque wrench, as the fastening
torque is affected by many factors including the following:
‑Voltage: Low voltage, due to a nearly discharged
battery, will reduce fasteningtorque.
‑Accessory size: Failure to use the correct accessory size
will cause a reduction in fasteningtorque.
‑Bolt size: Larger bolt diameters generally require
higher fastening torque. Fastening torque will also vary
according to length, grade, and torquecoefficient.
‑Bolt: Ensure that all threads are free of rust and other
debris to allow proper fasteningtorque.
‑Material: The type of material and surface finish of the
material will affect fasteningtorque.
‑Fastening time: Longer fasten ing time results in
increased fastening torque. Using a longer fastening
time than recommended could cause the fasteners to
be overstressed, stripped ordamaged.
MAINTENANCE
Your power tool has been designed to operate over a long
period of time with a minimum of maintenance. Continuous
satisfactory operation depends upon proper tool care and
regularcleaning.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start‑up can causeinjury.
The charger and battery pack are notserviceable.
Lubrication
Your power tool requires no additionallubrication.
Cleaning
WARNING: Electrical shock and mechanical hazard.
Disconnect the electrical appliance from the power source
beforecleaning.
WARNING: To ensure safe and efficient operation,
always keep the electrical appliance and the ventilation
slotsclean.
WARNING: Never use solvents or other harsh chemicals
for cleaning the non‑metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into aliquid.
Ventilation slots can be cleaned using a dry, soft non‑metallic
brush and/or a suitable vacuum cleaner. Do not use water or
any cleaning solutions. Wear approved eye protection and an
approved dustmask.
11
ENGLISH
Optional Accessories
WARNING: Since accessories, other than those offered
by DeWALT, have not been tested with this product, use
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only DeWALT recommended
accessories should be used with thisproduct.
Consult your dealer for further information on the
appropriateaccessories.
Protecting the Environment
w
Separate collection. Products and batteries marked
with this symbol must not be disposed of with normal
householdwaste.
Products and batteries contain materials that can be
recovered or recycled, reducing the demand for raw materials.
Please recycle electrical products and batteries according to local
provisions. Further information is available at
www.2helpU.com.
Rechargeable Battery Pack
This long‑life battery pack must be recharged when it fails to
produce sufficient power on jobs that were easily done before.
At the end of its technical life, discard it with due care for
ourenvironment:
• Run the battery pack down completely, then remove it from
thetool.
• Li‑Ion cells are recyclable. Take them to your dealer or a
local recycling station. The collected battery packs will be
recycled or disposed ofproperly.
After Service and Repair
DeWALT service centers are staffed with trained personnel to
provide customers with efficient and reliable product service.
We do not take any responsibility when you have repaired
in unauthorized service center. You can refer to the leaflet of
CONTACT CENTER LOCATOR in product package and contact
us through hotline, website or social media to find the nearest
DeWALT service center around you.
繁體中文
12
繁體中文
3
恭喜！
感謝您選購
DEWALT
工具。憑藉多年的產品開發和創新經驗，
DEWALT
已經成為專業電動工具用戶最可靠的合作夥伴之一。
技術資料
請注意！各地區上市產品/配件不盡相同，請依台灣繁體中文說明書的內容為主。
DCF961
電壓 VDC 18 (20 Max)
電池類型 鋰離子
輸出功率 瓦870
無負荷轉速 min-1 0-440/800/1200
衝擊速率 min-1 0-1890
最大緊固扭矩
Precision Wrench™ 模式
低模式
中模式
高模式
Nm
Nm
Nm
Nm
1496
135
1220
1626
最大起動扭矩 Nm 2372
重量（不含電池組） 千克 3.5
電池 充電器 / 充電時間（分鐘）***
型號 電壓 Vdc 電池容量 (AH)重量 (kg) DCB107 DCB115
DCB1104 DCB118 DCB1112
DCB606 18/54 ( 最大 20/60) 6.0/2.0 1.05 270 90 60 40
DCB609 18/54 ( 最大 20/60) 9.0/3.0 1.46 420 135* 75* 60
DCB612 18/54 ( 最大 20/60) 12.0/4.0 1.44 540 180 120 80
DCB203 18 ( 最大 20) 2.0 0.40 90 30 30 30
DCB205 18 ( 最大 20) 5.0 0.62 240 75 75/50** 75/50**
DCB240 18 ( 最大 20) 4.0 0.54 185 60 60 60
DCBP034 18 ( 最大 20) 1.7 0.32 82 27 27 27
DCBP520 18 ( 最大 20) 5.0 0.75 240 75 75/50** 75/50**
*日期碼201811475B或之後
**日期碼201536或之後
***電池充電時間僅供指導；具體充電時間取決於溫度和電池的實際情況。
a
警告：為降低受傷的風險，用戶必須仔細閱讀使用手冊。
定義：安全指南
以下定義描述了每個信號詞的嚴重程度。請閱讀手冊並留意這些
符號。
危險：表示緊急的危險情況，如不加以避免，將導致死亡或
嚴重傷害。
警告：表示潛在的危險情況，如不加以避免，將導致死亡或
嚴重傷害。
小心：表示潛在的危險情況，如不加以避免，將導致輕度或
中度傷害。
注意：表示不涉及人身傷害的情況，如不加以避免，可能導
致財產損失。
表示存在觸電風險。
表示存在火災風險。
電動工具通用安全警告
警告：請閱讀本電動工具隨附的所有安全警告、指示、圖示
和規格。不遵循下列的所有指示可能會導致觸電、火災及/
或嚴重傷害。
保存所有警告和說明書以備今後查閱
警告中的名詞「電動工具」是指電源驅動（插電）電動工具，或者電池
驅動（充電）電動工具。
1 ) 工作場地安全
a )
請保持工作場地清潔明亮。混亂或昏暗的場地會引發事故。
20V MAX XR 1/2"
大扭力衝擊扳手
DCF961
繁體中文
13
繁體中文
4
b )
請勿在易爆環境，如有易燃液體、氣體或粉塵的環境中操作
電動工具。電動工具產生的火花會點燃粉塵或氣體。
c )
請等待兒童和旁觀者離開之後才操縱電動工具。分心會讓
您失去對工具的控制。
2 ) 電氣安全
a )
電動工具插頭必須與插座相符。不得以任何方式改裝插頭。
需接地的電動工具不能使用任何配接器插頭。未經改裝的
插頭和相符的插座可以減少觸電危險。
b )
避免人體接觸接地表面，如管道、散熱片、爐灶和冰箱。若您
的身體接地，會增加觸電危險。
c )
不得將電動工具暴露在雨中或潮濕環境中。水進入電動工
具會增加觸電危險。
d )
請勿濫用電線。請勿使用電線來搬運、拉動電動工具或拔出
插頭。請讓電線遠離熱、油、銳邊和轉動部件。受損或纏繞的
電線會增加觸電危險。
e )
若要在戶外使用電動工具，請使用適合戶外使用的延長電
線。使用適合戶外使用的電線可減少觸電危險。
f )
若必須在潮濕場合使用電動工具，請使用漏電保護器
(RCD)。使用 RCD 可降低觸電危險。
3 ) 人身安全
a )
保持警覺；在操作電動工具時，請留意所執行的操作並按照
一般的程式執行。請勿在疲倦或在受到毒品、酒精或藥品的
影響時使用電動工具。操作電動工具期間注意力分散會導
致嚴重人身傷害。
b )
請使用個人防護裝置。始終佩戴護目裝置。防護裝置，例如
在適當條件下使用的防塵面具、防滑安全鞋、安全帽或聽力
保護等裝置可減少人身傷害。
c )
避免意外啟動。連接電源及/或電池組、舉抬或搬運電動工
具之前，請確定開關處於關閉位置。若搬運電動工具時將手
指放在開關上，或者在電動工具開關開啟時將插頭插入電
源插座，這兩種行為都會引發事故。
d )
啟動電動工具之前，請卸下所有的調整鑰匙或扳手。遺留在
電動工具旋轉部件上的扳手或鑰匙會導致人身傷害。
e )
請勿過度伸展雙手。時刻注意腳下與身體的平衡。如此即可
在發生意外的情況下更好地控制電動工具。
f )
適當穿著。請勿穿寬鬆衣服或佩戴飾品。讓頭髮、衣服和
手套遠離活動部件。寬鬆衣服、佩飾和長髮可能會捲入轉
動部件。
g )
若配備用於連接排屑裝置和集塵設備的裝置，請確定正
確連接和使用這些裝置。使用集塵設備可減少與粉塵有關
的危險。
h )
請勿因為頻繁使用工具而產生的熟悉感而掉以輕心，忽
視工具的安全準則。某個粗心的動作可能會在瞬間導致嚴
重傷害。
4 ) 電動工具的使用和注意事項
a )
請勿超負荷使用電動工具。請根據不同應用需求選用合適
的電動工具。若使用的電動工具正確無誤，該工具能以設計
額定值更有效、更安全地執行工作。
b )
若開關不能開啟或關閉電源，請勿使用該電動工具。若開關
無法控制電動工具，則電動工具存在危險，必須予以維修。
c )
在執行任何調整、更換配件或儲存工具之前，必須從電源上
拔掉插頭及/或卸下電池組。這類防護性措施可降低電動工
具意外啟動的風險。
d )
請將閒置的電動工具存放在兒童無法觸及的地方，同時請
勿讓不熟悉電動工具或對這些使用說明不瞭解的人員操作
電動工具。電動工具在未經培訓的使用者手中會發生危險。
e )
維護電動工具和附件。檢查活動部件是否對準或卡住、破損
情況以及是否存在影響電動工具運行的其他情況。若有損
壞，這必須在使用之前修理電動工具。許多事故都是由於電
動工具欠缺維護所導致。
f )
保持刀具鋒利和清潔。妥善維護的帶利刃的切削工具不會
被輕易卡住，而且更易控制。
g )
使用電動工具、配件和工具刀頭等時，請遵循這些指示使
用，並且亦需考慮工作環境和有待執行的工作。不按照設計
目的使用電動工具會導致危險。
h )
保持手柄和握持面乾燥、清潔、不油膩。在意外情況下，濕滑
的手柄不能保證握持的安全以及對工具的控制。
5 ) 電池工具的使用與注意事項
a )
只能使用製造商指定的充電器為電池充電。使用僅適合
一種電池組的充電器為其他類型的電池組充電會導致火
災風險。
b )
請为電動工具使用指定的電池組。使用其他電池組會導致
人身傷害和火災危險。
c )
不使用電池組時，請將其遠離如迴紋針、硬幣、鑰匙、釘子、
螺釘以及其他可連通電池兩極的金屬物品。短接電池端子
可能會引發燃燒或火災。
d )
濫用電池的情況下，液體會從電池中噴出；避免與液體接
觸。如果不慎接觸到電池液，請用水沖洗。如果電池液接
觸到雙眼，請就醫。從電池噴出的液體會刺激皮膚或造成
灼傷。
e )
請勿使用已經損壞或改動的電池組或工具。損壞或改動
的電池可能表現出不可預計的行為，導致火災、爆炸或傷
害風險。
f )
請勿讓電池組或工具暴露於火中或過高溫度的環境中。暴
露於火中或溫度超過130°C的環境中可能導致爆炸。
g )
請遵循所有充電說明，請勿在說明中規定的溫度範圍以外
的環境對電池組或工具充電。不當充電或在指定範圍以外
的溫度下充電，可能導致電池損壞並增加火災風險。
6 ) 檢修
a )
維修本電動工具時，必須由合格的維修人員執行，而且只能
使用完全一致的更換件。這樣將確保電動工具的安全。
b )
切勿維修損毀的電池組。電池組的維修應僅由製造商或授
權服務提供商進行。
衝擊扳手/起子安全警告
⸺ 全部操作
•
若在操作中，緊固件會觸及隱藏在墻內的電線，請握住電動工
具的絕緣握持面 。緊固件碰到帶電導線可能會使電動工具的外
露金屬零件帶電，並讓操作人員面臨觸電危險。
•
在使用時，請佩戴聽力保護裝置。暴露在噪聲中會引起聽力
損傷。
警告：衝擊扳手並非扭矩扳手。請勿 使用該工具將緊固件
擰到特定扭矩。若緊固件不夠緊固或過於緊固，會導致結
合處出現故障，應使用警告校準的獨立扭矩測量設備，例
如扭矩扳手。
繁體中文
14
繁體中文
5
充電器
DEWALT
充電器無需調節。它的設計十分簡便，易於操作。
電氣安全
電機只適用一種工作電壓。請務必檢查電池組的電壓是否和銘牌上
的電壓一致。還要確保充電器的電壓與電源電壓一致。
i您的
DEWALT
充電器已按照IEC60335實現雙層絕緣；因
此無需接地線。
如果電線損壞，必須只能由
DEWALT
或授權服務中心負責更換。
使用延長線
除非絕對必要，否則請勿使用延長線。使用適合您的充電器輸入功
率的合格延長線（見
技術數據
）。最小的導線尺寸為1平方公釐；最大
長度為30米。
使用電纜捲筒時，請務必拉出所有的電纜。
面向所有電池充電器的重要安全說
明
請妥善保管好這些說明:
本手冊包含重要的相容電池充電器安全和
操作說明（請參閱
技術數據
）。
在使用充電器之前，請先閱讀所有指示
以及充電器、電池組和使用電池組的產品上的警告標記。
警告：觸電危險請勿讓任何液體進入充電器。否則可能會
導致觸電。
警告：我們建議使用漏電保護額定電流為30毫安或以下的
漏電保護裝置。
小心：灼燒危險。為降低人身傷害風險，請僅使用
DEWALT
充
電式電池充電。其它類型電池可能會引起爆裂並導致人身
傷害和損壞。
小心：應看管好兒童，確保他們不會將此設備當做玩具來
玩。
注意：在某些情況下，當充電器的插頭插入電源插座時，充
電器內部裸露的充電接觸點可能因為異物而短路。請勿讓
能導電的異物靠近充電器腔，這些異物包括但不限於鋼棉、
鋁箔或任何金屬顆粒的堆積物。充電器內沒有電池組時，請
斷開充電器與電源的連接。清洗前，務必拔掉充電器。
•
請勿試圖使用本手冊指定的充電器以外的其他任何充電器為
電池組充電。充電器和電池組都是專門設計的，互相配合使用。
•
除了為
DEWALT
充電式電池充電以外，這些充電器並非設計用
於其他用途。否則，可能會導致火災、觸電或電擊致死。
•
請勿將充電器暴露於雨中或雪中。
•
斷開充電器連接時，應捏住插頭將其拔下，而非通過拉拽電源線
拔下插頭。這將降低對電插頭和電線的損害風險。
•
確保電源線佈置在不易踩踏、踢絆、拉扯或會受到損害或壓力
的位置。
•
除非絕對必要，否則請勿使用延長線。使用不合適的延長線可
能導致火災、觸電或電擊致死的風險。
•
請勿將任何物件放在充電器上面，或是把充電器放在可能會
堵住通風槽的柔軟表面，導致充電器的內部過熱。請將充電器
放置在遠離任何熱源的地方。充電器通過外殼頂端和底端的
槽進行通風。
•
請勿使用電源線或插頭已損壞的充電器，請立即更換這些充
電器。
•
如果充電器受到強烈重擊、掉落或出現其他損壞情況，請勿使
用充電器。請將損壞的充電器送到授權服務中心。
•
請勿自行拆卸充電器。請將需要檢修或修理的充電器送到授權服
務中心。重裝不正確可能導致觸電、電擊致死或火災風險。
•
必須立即將已損壞的電源線交由製造商、服務代理或類似的具
備資質的人員進行更換，以防止安全隱患。
•
清潔前，請先斷開充電器和插座的連接。這樣可降低觸電危險。
取出電池組不會降低此風險。
•
不得將兩個充電器連接在一起。
•
充電器是為 110伏特的標準家用電源而設計。請勿試圖在任何
其他電壓下使用充電器。此規則不適用於車載充電器。
為電池充電（圖B）
注意：為了確保鋰電池組的效能及使用壽命最大化，在第一次使用
電池組之前必須完全充電。
1. 先將充電器插入適當的插座中，再插入電池組 。
2. 將電池組 5 插入到充電器中，確定電池組完全就位。紅色的充
電指示燈會持續閃爍，表示充電已經開始。
3. 階段 1 充電閃爍指示燈，表示該充電過程能補充電池的大部分
電量。階段 2 充電閃爍指示燈，表示該充電過程能讓電池電量
達到滿格。
4. 充電指示燈常亮，表示階段 1 或階段 2 的充電已經完成。當階
段 1 和階段 2 的充電指示燈常亮，表示電池組電量已經充滿，
可將其從充電器上取下使用，或將其留在充電器上。
注意：如需取下電池組，在一些充電器上，需要按壓 5 釋放按鈕。
充電器操作
關於電池組的充電狀態，請參閱以下有關指示燈的說明。
指示燈
階段 1 充電中
階段 2 充電中
電量已充滿
熱 / 冷電池組延遲 *
* 紅色指示燈會繼續閃爍，但黃色指示燈在本次操作過程中會亮
起。電池組達到適當溫度後，黃色指示燈會熄滅，充電器將恢復
充電程式。
此兼容充電器不能為故障的電池組充電。充電器指示燈不亮時表
示電池有故障。
注意：亦有可能是充電器發生故障。
如果充電器提示存在故障，請將充電器和電池組送到授權的服務
中心進行測試。
熱/冷電池組延遲
當充電器檢測到電池组過熱或過冷時，它會自動啟動熱/冷電池延
遲模式，暫停充電，直到電池組達到適當的溫度。然後，充電器將自
動切換到電池組充電模式。該特色功能可以最大程度地延長電池組
的使用壽命。
冷電池組的充電速度比熱電池組的充電速度慢。電池組在整個充
電週期的充電速度都比較慢，及時電池組升溫，也不會恢復到最
大速度。
繁體中文
15
繁體中文
6
DCB118充電器配備專用於冷卻電池組的內部風扇。當電池組需要冷
卻時，風扇會自動啟動。如果風扇運轉不正常或通風槽堵塞，不得操
作充電器。請勿讓任何異物進入充電器內。
電子保護系統
XR 鋰電池工具在設計時採用了電子保護系統，可讓電池組免受過
載、過熱或過度放電之害。
如果電子保護系統處於運作狀態，該工具將自動停止運轉。如果發
生這種情況，請將鋰電池組放在充電器上，直至電量已充滿。
壁掛式安裝
這些充電器被設計為可安裝在墻面上，也可以直立在桌面或工作台
上。如果安裝在牆上，請確保充電器的位置可以連接到電源插座，並
且遠離牆角或其他可能妨礙空氣流通的障礙物。將充電器的背面作
為範本，在牆上確定安裝螺釘的位置。使用至少25.4毫米長、螺釘帽
直徑至少7-9毫米的石膏板螺釘（單獨購買）牢牢固定充電器，將螺
釘最大限度地釘入木材，在牆外預留約5.5毫米的長度。將充電器背
面的安裝槽對準露出的螺釘，同時讓螺钉與安裝槽完全吻合。
充電器清潔說明
警告：觸電危險清潔前，請先斷開充電器和交流電插座的連
接。可用布或非金屬軟刷清除充電器外部的污垢和油脂。請
勿使用水或任何清潔劑。不得讓任何液體滲入工具；不得將
工具的任何部件浸沒在液體中。
電池組
面向所有電池組的重要安全說明
在訂購更換電池組時，請務必附上型號和電壓。
包裝箱內的電池組電量並未充滿。使用電池組和充電器之前，請閱
讀下列安全說明。然後遵循所述的充電流程。
請閱讀所有說明
•
請勿在易爆環境（如含有易燃液體、氣體或粉塵的環境）中操作
電動工具，或爲其充電。在充電器中插入或取出電池時，可能會
點燃粉塵或氣體。
•
不得強行將電池放進充電器。請勿以任何方式改裝電池組並將
電池組插入不相容的充電器，這種操作可能會導致電池組破
裂，造成嚴重的人身傷害。
•
僅使用
DEWALT
充電器為電池充電。
•
請勿讓液體噴濺到電池組上或將電池組浸沒到水或其他液
體中。
•
請勿在溫度可能低於4˚C (39.2˚F)（如冬天戶外的棚子或金屬
建築物中）, 或在溫度可能達到或超過40˚C (104˚F) 的地方（如
夏天戶外的棚子或金屬建築物中）存放或使用工具和電池組。
•
即使電池組嚴重受損或完全損壞，也請勿焚燒電池組。電池組
在火中會發生爆炸。鋰電池組在燃燒時會釋放有毒的氣體和
物質。
•
如果電池液接觸到皮膚，請立即用中性肥皂和清水沖洗接觸的
地方。如果電池液不慎進入眼睛，應睜開眼睛並用清水沖洗至
少15分鐘或直到刺激感消失為止。如需醫療救助，請告知醫護
人員。電池電解質由液態有機碳酸鹽和鋰鹽的混合物組成。
•
電池被打開後，其內容物可能會刺激呼吸道。引入新鮮空氣。若
症狀持續，請盡快就醫。
警告：灼燒危險。電池液如果接觸到火花或火焰可能會燃
燒。
警告：無論何種原因，均不得嘗試打開電池。電池組外殼破
裂或損壞時，請勿將電池組插入充電器。請勿擠壓、掉落或
損壞電池組。請勿使用受過強烈重擊、掉落、碾壓或以任何
其他方式（如被釘子穿破、受到錘子重擊、踩踏）受損的電池
組或充電器。否則可能會導致觸電。損壞的電池組應送回服
務中心進行回收。
警告：火災危險。請勿在存儲或搬運電池組時，讓金屬物品
接觸暴露的電兩極。例如，請勿將電池組放在圍裙、口袋、
工具箱、產品套件箱、抽屜等可能存在散釘、螺釘、鑰匙等
物品的地方。
小心：不用時，請將工具側放在平穩的表面上，確保不存在
踢絆或掉落的危險。一些具有大型電池組的工具將直立於
電池組上，但可能會輕易被撞倒。
運輸
警告：火災危險。若電池在運輸過程中，其終端不慎接觸導
電材料，則會引發火災。在運輸電池時，請確保電池終端保
護得當，充分絕緣，不會接觸可能引發短路的材料。注意：不
應將鋰電池放入託運行李中。
DEWALT
電池符合所有適用的行業和法律標準規定的運輸規範，包
括《聯合國危險品運輸建議規章範本》(UN Recommendations on
the Transport of Dangerous Goods)、《 國際航空運輸協會 (IATA)
危險品規則》(International Air Transport Association(IATA)
Dangerous Goods Regulations) 、《國際海運危險品(IMDG) 規則》
(International Maritime Dangerous Goods (IMDG)Regulations)
和《歐洲危險貨物國際公路運輸協定》(European Agreement
Concerning The International Carriage of Dangerous Goods
by Road) (ADR)。已按照《聯合國危險品運輸建議規章範本》(UN
Recommendations on the Transport of Dangerous Goods)第
38.3條之規定對鋰電池和電池進行測試。
大多數情況下，發運
DEWALT
電池組不屬於完全管制的9類危險品。
通常情況下，只有當運輸包含一個能量等級大於100瓦時(Wh)的鋰
電池時，才需要作為完全管制的9類危險品發運。所有鋰電池外殼
上均標注有瓦時等級。此外，由於法規比較複雜，無論瓦時等級是多
少 ，
DEWALT
都不建議單獨空運鋰電池組。
發運包含電池的工作（組
合套件）時，如果電池組的能量等級不大於100瓦時(Wh)，則可以按
計畫空運。
無論發運是否納入完全管制範圍內，運輸公司均有責任遵循最新法
規中關於包裝、標籤/標記和單據的要求。
本手冊中本節的資訊是出於善意提供，且認為在編制文檔時準確無
誤。不過，我們不提供直接或間接的擔保。購買方負有確保其行為
遵守適用法規的責任。
存放建議
1. 最好將電池存放在陰涼、乾燥、遠離陽光直射、不會過熱或過冷
的地方。了獲得最佳的電池性能和使用壽命，請您在不使用電
池組時將其存放在室溫下。
2. 長期存放時，建議將電量充滿的電池組從充電器取出，存放在
陰涼、乾燥的地方，以達到最佳效果。
注意：電池組不應在電量耗盡的狀態下存放。使用電池組之前，必
須重新為電池組充電。
充電器和電池組上的標籤
除了在本手冊中所使用的標誌，充電器和電池組的標籤還包括：
繁體中文
16
繁體中文
7
L
請在使用前閱讀使用手冊。
p 請參見
技術數據
，了解充電時間。
q 請勿使用導電物體戳刺。
r 請勿對損壞的電池組充電。
s 請勿將其暴露於水中。
t 應立即更換受損電線。
u 請只在4°C和40°C之間的溫度下充電。
v 僅在室內使用。
x 棄置电池组時，請妥善處理，保護環境。
y 只使用指定的
DEWALT
充 電 器 為
DEWALT
電池組充電。使
用
DEWALT
充電器為非
DEWALT
電池組充電可能會導致爆
炸或引發危險。
z 請勿焚化電池組。
電池類型
更多資訊，請參閱
技術數據
。
包裝內的物品
包裝內的物品包括：
1 衝擊扳手
1 充電器
鋰電池組
1 說明手冊
1 TSTAK工具箱，帶有T型號
1 保護性工具靴
注意：N型號不包含電池組、充電器和工具箱NT型號不包含電池組
和充電器B型號包含Bluetooth®電池組。
注意：Bluetooth®的字樣和徽標是歸Bluetooth®, SIG公司所有的註
冊商標。
DEWALT
對該商標的任何使用均已獲得該公司的許可。其
他商標和商標名稱均歸屬於各自的所有者。
•
檢查工具、部件或配件是否在運輸過程中損壞。
•
操作前，請抽空仔細閱讀本說明書並理解其中的內容。
工具上的標記
工具上有以下圖像：
a 請在使用前閱讀使用手冊。
g
佩戴耳罩。
f 佩戴護目裝置。
n 可見輻射請勿直視燈光
日期碼位置（圖A）
生產日期碼 11 包含4位數的年份，之後是2位數的周數以及2位數
的工廠代碼。
說明（圖A）
警告：不得改裝本電動工具或其任何部件。否則可能造成人
身傷害或工具損壞。
1 觸發開關
2 正反轉切換按鈕
3 鐵砧
4 主手柄
5 電池組釋放按鈕
6 電池組
7 工作燈
8 工作燈開關
9 模式選擇器
10 弓形環
11 日期碼
設計用途
該衝擊扳手適用於專業衝擊緊固應用。在將緊固件打入木材、金屬
和混凝土中時，本產品的衝擊功能十分有用。
請勿在潮濕或存在易燃液體或氣體的環境下使用本工具。
這款衝擊扳手是專業電動工具。
請勿讓兒童接觸本工具。缺乏經驗的操作人員需要在接受監督的情
況下才可使用該工具。
• 兒童和體弱者。在沒有他人監督的情況下，兒童或體弱者不適
宜使用本工具。
• 本產品不適合體力、感官或智力不足以及缺乏經驗、知識或技
能的人員（包括兒童）使用，除非一旁有能為他們的安全負責的
監督人員。不得在無人監管的情況下讓兒童接觸本產品。
組裝與調整
警告：為降低造成嚴重人身傷害的風險，在進行任何調整、
拆卸 /安裝附件或配件前，切記關閉工具並斷開工具電源。
意外啟動可能會造成傷害。
警告：僅使用
DEWALT
電池和充電器。
插入和取出工具上的電池組（圖B）
注意：請確保您的電池組 5 電量已充滿。
將電池組安裝到工具手柄中
1. 將電池組與工具手柄內的軌道對齊 （圖B）。
繁體中文
17
繁體中文
8
2. 將電池組滑入手柄中，直到電池組被牢固地安裝在工具中，同
時確保聽見鎖定到位的咔噠聲。
從工具中取出電池組
1. 按下釋放按鈕 5 ，將電池組從工具握柄中慢慢拉出。
2. 按本手冊充電器部分所述，將電池組插入充電器中。
電池組電量計（圖B）
一 些
DEWALT
電池組帶有一個包含三個綠色LED指示燈的電量計，
用於指示電池組內的剩餘電量。
按下電量計按鈕不鬆開，即可啟動電量計 15 。三個綠色LED指示燈
將以組合方式亮起，以指示剩餘電量。當電池內的電量低於可用限
制時，電量計將不會亮起，電池將需要重新充電。
注意：電量計僅指示電池組的剩餘電量。它並不表示該工具的功能，
且將根據產品組件、溫度和最終用戶的使用情況而有所不同。
鐵砧（圖C）
警告：僅使用衝擊配件。非衝擊配件可能會破損，造成危險。
請在使用前檢查配件，確保配件上沒有裂痕。
小心：請在使用前檢查鐵砧和弓形環。應先更換缺失或受損
的部件，再使用產品。
請先將開關置於鎖定（中央）位置，或取下電池，再更換配件。
如需在弓形環上安裝配件，請用力將配件推到鐵砧上 3 。壓縮弓
形環 10 ，使得配件能夠滑入。安裝配件後，弓形環會施加壓力，將
配件固定住。
如需拆除配件，請握住配件並用力將其拉下。
模式選擇器（圖A, D）
您的工具配有模式選擇器 9 ，您可以在三檔速度中任選一檔，或選
擇Precision Wrench™模式。基於所需的最大速度/扭矩選擇模式，
同時使用變速觸發開關來控制工具轉速 1 。
PRECISION WRENCH™（圖D）
除了普通衝擊模式，該工具還有Precision Wrench™模式，讓用戶
能夠在緊固和鬆開應用中更好地掌控工具。若設定為正向轉動，工
具會在1200RPM緊固，直至衝擊開始。之後，工具會暫停0.75秒，再
繼續以1890IPM的速率衝擊，讓用戶能夠更好地控制工具，同時降
低過度擰緊材料或損壞材料的可能性。
若設定為反向轉動，工具會按照正常速度進行衝擊，速率為
1890 IPM。當感應到緊固件脫離，工具會停止衝擊並減速，防止已
鬆動的五金件脫落。
規格
模式 應用 RPM
Precision Wrench™模式 Precision Wrench™0–1200正向轉動
0–550反向轉動
低模式 普通衝擊 0–440正向轉動
0–1200反向轉動
中模式 中衝擊 0–800正向轉動
0–1200反向轉動
高模式* 高速衝擊 0–1200正向轉動
0–1200反向轉動
*在衝擊4秒後，DCF961會自動增強功率，幫助鬆開頑固的緊固件。
操作
使用說明
警告：務必遵守安全指示和適用的規定。
警告：為降低造成嚴重人身傷害的風險，在進行任何調整、
拆卸 /安裝附件或配件前，切記關閉工具並斷開工具電源。
意外啟動可能會造成傷害。
變速觸發開關（圖A）
如需啟動工具，請按壓觸發開關 1 。如需關閉工具，請鬆開開關。您
的工具配有制動裝置。當完全鬆開觸發開關，鐵砧將停止。邊度開
關讓您能夠針對特定應用選擇適當速度。越是用力按壓觸發開關，
工具轉速越快。為充分延長工具壽命，僅在打洞或處理緊固件的開
始階段使用變速功能。
注意：不建議在不同的速度檔位上持續使用工具。這樣會損壞開
關，應注意避免。
正反轉切換按鈕（圖A）
正反轉切換按鈕 2 能夠決定工具轉向，同時它也是鎖定按鈕。
如需正向轉動，請鬆開觸發開關，並按下工具右側的正反轉切換
按鈕。
如需反向轉動，請鬆開觸發開關，並按下工具左側的正反轉切換
按鈕。
控制按鈕的中間位置能夠將工具鎖定在關閉位置。若要改變控制按
鈕的位置，務必要鬆開觸發開關。
注意：在改變轉向後首次運行工具時，您可能會在啟動時聽見咔噠
的聲響。這是正常情況，並非出現問題。
工作燈（圖A, D）
當鬆開變速觸發開關 1 ，工作燈 7 就會亮起。反復按壓工作燈開
關 8 ，就能夠按照低亮度、高亮度和關閉的順序，循環調節燈光亮度。
注意：工作燈能夠照亮近距離的工件表面，不可將其用作電筒。
正確的雙手放置位置（圖E）
警告：為了降低嚴重人身傷害的風險，請務必如圖所示，正
確放置雙手。
警告：為了降低造成嚴重人身傷害的風險，在預期有突然反
作用力時務必握緊工具。
正確放置雙手要求您一手握住主手柄 8 。
使用（圖A）
小心：請確保緊固件和/或系統能夠耐受工具產生的扭矩。
扭矩過大會導致斷裂並可能導致人員受傷。
1. 請將配件置於緊固件的頭部。請讓工具始終直指緊固件。
2. 若要開始運轉，請按壓變速觸發開關 1 。若要停止運轉，請鬆開
變速觸發開關。務必使用扭矩扳手檢查扭矩，因為緊固扭矩會
受到很多因素的影響，其中包括：
‑電壓：低電壓（電量幾乎耗盡）會降低緊固扭矩。
‑配件尺寸：未能使用正確的配件尺寸會降低緊固扭矩。
繁體中文
18
繁體中文
9
‑
螺栓尺寸：更大的螺栓直徑一般要求更大的緊固扭矩。緊固
扭矩也會根據長度、級別和扭矩係數而相應變化。
‑螺栓：確保所有螺紋均無鏽蝕和其他碎屑，確保適當的緊
固扭矩。
‑材料：材料類型和材料表面的飾面效果也會影響緊固扭矩。
‑緊固時間：更長的緊固時間會增加緊固扭矩。若緊固時間超
過建議時長，會導致緊固件受到過大壓力、滑牙或受損。
維護
您的電動工具只需簡單保養，即可長期使用。若要持續獲得滿意的
操作效果，需進行正確的工具維護和定期的清潔。
警告：為降低造成嚴重人身傷害的風險，在進行任何調整、
拆卸 /安裝附件或配件前，切記關閉工具並斷開工具電源。
意外啟動可能會造成傷害。
充電器和電池組是不可維修的。
潤滑
您的電動工具無需額外潤滑。
清潔
警告：觸電和機械危害請先切斷設備電源，再進行清潔。
警告：為確保操作安全、高效，請務必保持電動設備和通風
槽的清潔。
警告：不得使用溶劑或其他刺激性化學品來清潔工具的非
金屬部件。化學品可能會削弱製造零部件所用的材料。僅使
用蘸水濕布和溫和的肥皂擦拭。不得讓任何液體滲入工具；
不得將工具的任何部件浸沒在液體中。
可使用乾燥、柔軟的非金屬刷和/或恰當的吸塵器清潔器來清潔通
風槽。請勿使用水或任何清潔劑。請佩戴獲得批准的護目鏡和防
塵面具。
可選配件
警告：除了
DEWALT
提供的配件之外，其他配件都未接受過
此產品的兼容性測試。若將此類配件與本產品搭配使用，
將存在安全隱患。為降低人身傷害風險，本產品只可使用
DEWALT
推 薦 的 配 件 。
請咨詢您的經銷商，了解更多關於合適配件的信息。
保護環境
w分類回收。帶有此標誌的產品和電池必須與一般家庭廢
物分開處置。
產品和電池包含可重複使用或回收的材料，可降低對原材
料的需求。請根據當地法規回收電氣產品和電池。更多資
訊，請造訪
www.2helpU.com
可充電的電池組
如果這種壽命較長的電池組無法提供順利完成工作所需的功率，則
必須為其充電。當達到技術壽命的終點時，請在丟棄時務必多加小
心，注意保護環境。
• 請先徹底耗盡電池電量，然後將其從工具上拆下。
• 鋰電池可循環使用。將它們送至經銷商或當地的回收站。被回收
的電池組將被回收利用，或通過妥善方式處理。
售後服務和維修
DEWALT
維修中心擁有經過培訓的人員，能夠為顧客提供充分、可
靠的產品服務。如果您通過未獲授權的維修中心進行維修，我們不
會承擔任何責任。您可以參見產品包裝中的“聯繫中心定位器”宣
傳單頁，通過熱線電話、網站或社交媒體聯繫我們，找到距離您最
近的
DEWALT
服務中心。
進 口 商: 新加坡商百得電動工具 股)公司台灣分公司
地 址:台北市士林區德行西路33 號2 樓
電 話: 02-28341741
總 經 銷 商: 永安實業股份有限公司地址: 新北市三重區新北大道
二段137 號
電 話: 02-29994633
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
/