173
最小 /
min. 50
490
+2
r3
最小 /
min. 100
270
zh
en
1.
x4
Ø6
90
°
9000738205
9006
安装说明
请保存
2. 3.
Installation Instructions
please keep
4. 5.
6. 7.
zh en
重要说明
这款嵌入式电烤灶台用于嵌入橱柜操作
面上的切口。仅当按照所提供的安装说
明使用时才能保证电器安全。
由于安装不当导致的损坏，应由安装人
员承担责任。
只能由持有证书的专业人员连接本电器。
请遵守当地供电商规范及建筑规范。
检查电器是否有任何运输损坏。
安装时断开电器电源。
准备橱柜
在要安装电器的橱柜上，必须使用防热
粘合剂处理塑料涂层和 / 或面板。切口处
的粗糙边缘必须使用硅树脂等防水材料
进行密封。在嵌入式电磁灶后面的厨柜
操作面表面上不得使用塑料填充胶条。
安装
将电烤灶台插入切口，使控件朝前，然
后使用夹紧元件将其安装到位。
说明：请确保电烤灶台下方有充足的空
间，用于放置收集水滴的容器。
电气连接
本电器连接不带插头的电源线。遵守安
装地国家有关电器连接规定。
检查铭牌上的电压和总输出。本电器必
须接地。
安装后，如果插头无法触及，则必须在
安装侧安装一个全电极隔离开关，触点
间隙至少为 3 mm。
电源线必须为 H05VV-F 或 H05VVH2-F
型或更高型号。横截面：3G1.5 mm
2
连接导线若有损坏则必须更换。只能由
我公司派出的售后服务技术人员进行更
换。
进行修理之前必须断开电器的电源。如
果需要修理，切勿自行打开电器，请联
系我们的售后服务人员。
成套安装组件
如果要将两个或更多个单元相邻安装，
需要一个或更多安装套件。
Important notes
This built-in grill is intended for insertion
into a cutout in the worktop. The
appliance is only guaranteed safe to
use if installed in accordance with these
installation instructions.
The installer is liable for any damage
resulting from incorrect installation.
The appliance may only be connected
by a licensed specialist. The local
electricity supplier’s regulations and
construction regulations apply.
Check the appliance for any transport
damage.
Disconnect the appliance during
installation.
Preparing the cabinet
On the furniture into which the appliance
is to be installed, the plastic coating and/
or veneer must have been treated with
a heat-resistant adhesive. The rough
edges of the cutout must be sealed
using a watertight material, e.g. silicone.
The use of plastic filler strips on the
worktop surface behind the built-in hob
is not permitted.
Installation
Insert the grill into the cutout with the
controls facing the front and attach it
using the clamping elements.
Note: Please ensure that there is
sufficient room underneath the grill for a
container to collect the water.
Electrical connection
The appliance is fitted with a mains
connecting cable without plug. Observe
the current national regulations when
connecting the appliance.
Check the voltage and total output on
the rating plate. It is obligatory that this
appliance be earthed.
If the plug is no longer accessible after
installation, an all pin isolating switch
with a contact gap of at least 3 mm must
be installed.
The mains connecting cable must be
of the H05VV-F or H05VVH2-F type or
higher. Cross-section: 3G1,5 mm
2
The connecting lead must be replaced
if it has been damaged. This can only
be carried out by one of our after-sales
service technicians.
The appliance must always be
disconnected from the mains before
repairs are carried out. If repairs are
needed, never open the appliance
yourself, but call our after-sales service.
Installation set
When installing two or more units next
to each other, one or more installation
kits will be required.
nl it es
-
1
-
2
-
3
-
4
