Red Sea 212158 RSK 300 Reefer Internal Protein Skimmer, REEFER Skimmer 300, REEFER Skimmer 600, REEFER Skimmer 900 ユーザーマニュアル

  • Red Sea REEFERシリーズプロテインスキマー(300、600、900)のユーザーマニュアルの内容を理解しています。設置方法、操作方法、メンテナンス方法、トラブルシューティングなど、このスキマーに関するご質問にお答えします。FoamViewウィンドウやネッククリーナーといった便利な機能についてもご説明できます。
  • スキマーの泡の調整方法は?
    スキマーのメンテナンス頻度は?
    ネッククリーナーの使い方を教えてください。
ENG DE FR CHNJP
User Manual
50-65JP
67-81CHN
35-49FR
19-33DE
3-17ENG
ENG
3
Efficient - Quiet - Ergonomic
User Manual
RED SEA REEFER™ Skimmer
4
Contents
Features of the REEFER Skimmers......................................7
Safety Instructions.................................................................8
Parts Diagram.........................................................................9
Assembly..............................................................................10
Installation...........................................................................13
Operation.............................................................................13
Maintenance........................................................................14
Troubleshooting...................................................................15
Warranty...............................................................................16
ENG
5
Welcome
Congratulations on the purchase of your
Red Sea REEFER Skimmer.
The REEFER Skimmer combine high performance with innovative design
features, super quiet operation and ease of use.
To get the maximum benefit from your new skimmer follow the
instructions and recommendations contained in this manual.
If you have any difficulties installing or operating this product please
contact our after sales service team through our web-site.
Wishing you successful reefing,
Red Sea Team.
RED SEA REEFER™ Skimmer
6
Introduction to protein skimming
Protein skimming (also called foam fractionation) can be considered as a
form of fine mechanical filtration since it is a physical process of removing
substances from the water. Whilst a mechanical filter removes large
particles such as uneaten fish food, a protein skimmer removes suspended
or dissolved organic waste and invisible particles from the aquarium water.
The advantage of protein skimming lies in the fact that waste material
is continuously removed, separating it from the water flow. The waste,
suspended in foam, is then collected into a cup where it is no longer
in contact with the aquarium water. In contrast, the dirt collected in
an ordinary mechanical filter stays in contact with the water flow. A
mechanical filter should therefore be cleaned very regularly; otherwise
bacteria will decompose the collected dirt into harmful dissolved organic
material.
A successful reef aquarium should have both a regularly cleaned
mechanical filter and an efficient protein skimmer as the first and second
stage of the water treatment process.
Why is protein skimming important?
Protein skimming plays a very important role in reducing the amount of
dissolved organic material in your aquarium water. This material consists
of protein, carbohydrate and fat fragments together with other waste
produced by the living organisms in the aquarium.
Since these could break down to potentially harmful materials to the
aquarium inhabitants, rapid removal is essential.
Efficient removal of dissolved waste also helps to:
Limit the build-up of harmful organic compounds including dissolved
organic carbon, nitrogenous components (ammonia, nitrite, nitrate)
and phosphates.
Reduce the quantity of harmful floating bacteria, since bacteria need
dissolved organic material in order to grow and reproduce.
Increase ORP (Oxidation, Reduction potential also known as REDOX) and
dissolved oxygen levels.
Prevent the development of slime algae (Cyanobacteria or blue green
algae). The main food source of these primitive algae (dissolved
organic material, nitrate and phosphate) is kept at a very low
concentration.
REEFER Skimmer Ratings
The REEFER Skimmers are rated according to Red Sea’s REEF-SPEC®
criteria that includes a water throughput, water to air ratio and contact
time necessary to efficiently strip pollutants from the water. Powered
by the Sicce PSK pumps, the stated air and water flow rates are actual
measurements of these pumps when running on the REEFER Skimmers.
Model RSK-300 RSK-600 RSK-900
SPS rating (L/Gal) 300 / 80 600 / 160 900 / 240
Mixed Reef rating (L/Gal) 600 / 160 1200 / 320 1800 / 500
Fish Only rating (L/Gal) 900 / 240 1800 / 500 2700 / 740
Pump (Sicce) PSK-600 PSK-1000 PSK-1200
Air flow (lph/gph) 500 / 130 750 / 195 900 / 235
Water flow (lph/gph) 1000 / 265 1500 / 400 2000 / 530
Total Height (cm/inch) 53cm / 2156cm / 2259cm / 23
Recommended Water Height 16-20cm
6-8
18-20cm
7-8”
20-24cm
8-9”
ENG
7
Features of the REEFER Skimmers Unique Features
The neck of the protein skimmer is the section where the dense bubbling
air/water mixture gradually transforms into a stable foam.
The FoamView window built into the front of the collection cup provides
a clear view of the foam formation inside the skimmer neck, enabling easy
adjustment to reach the desired consistency of the foam.
Over time, if not cleaned regularly, a thick layer of organic sludge will form
on the inside of the neck, reducing foam production by 30-40%.
The integrated manual neck cleaning system of the REEFER Skimmer
provides a simple and effective solution by scraping the organic deposits
from the neck. Any of the organics that fall back into the top of the reaction
chamber are immediately ushed back up into the collection cup.
FoamView window
for ease of
foam regulation
Highly effective
air intake
silencer
Drainage port
with 1m / 39"
valved hose
Graduated cup for
easy monitoring of
waste production
Integrated
neck cleaner
High volume
reaction chamber
for optimal air /
water
contact time
Hydrodynamically
efcient bubble
diffusion chamber
Sicce PSK
skimmer pump
Easy maintenance Click in/out
pump holder
Precision
geared
skim
regulator
3 position
base assembly to set pump inlet/
regulator position according to sump
Vibration
reducing
connectors
and feet
RED SEA REEFER™ Skimmer
8
Important Safety Instructions
PLEASE READ AND FOLLOW ALL SAFETY
INSTRUCTIONS
DANGER: To avoid possible electric shock, special care should be taken
when handling a wet aquarium. For each of the following situations, do
not attempt repairs yourself; return the appliance to an authorized service
facility for service or discard the appliance.
WARNING: To guard against injury, basic safety precautions should be
observed, including the following:
a. Do not operate any appliance if it has a damaged cord or plug, if it is
malfunctioning, or if it is dropped or damaged in any manner.
b. To avoid the possibility of the appliance, plug or receptacle getting
wet, position the Skimmer to one side of a wall mounted receptacle to
prevent water from dripping onto the receptacle or plug. A “drip loop”,
as shown in the diagram should be arranged for each cord connecting
an aquarium appliance to a receptacle. The drip loop is that part of
the cord below the level of the receptacle or the connector. Use an
extension cord if necessary to prevent water traveling along the cord
and coming into contact with the receptacle.
c. If the plug or receptacle does get wet, DO NOT un-plug the cord.
Disconnect the fuse or circuit breaker that supplies power to the
appliance. Then, unplug the device and examine for presence of water
in the receptacle.
d. Close supervision is necessary when any appliance is used by
or near children.
e. To avoid injury, do not contact moving parts.
f. Always unplug an appliance from an outlet when not in use, before
putting on or taking off parts, and before cleaning. Never pull the cord
itself to remove the plug from the outlet.
Grasp the plug rmly and pull to disconnect.
g. Do not use an appliance for anything other than its intended use.
The use of attachments not recommended or sold by the appliance
manufacturer may cause an unsafe condition.
h. Do not install or store the appliance where it will be exposed to the
weather or to temperatures below freezing point.
i. Make sure an appliance mounted on a tank is securely installed before
operating it.
j. Read and observe all IMPORTANT notices on the appliance.
k. If an extension cord is necessary, a cord with a proper rating should be
used.
SAVE THESE INSTRUCTIONS
Drip loop
ENG
9
REEFER Skimmer Parts Diagram
Part Identication Part Description
REEFER
Skimmer 300
R50503
REEFER
Skimmer 600
R50506
REEFER
Skimmer 900
R50509
Qty.
ACollection Cup
& Lid R50523 R50533 R50543 1
B Wiper & Blades R50527 R50537 R50547 1
CWaste Tube &
Valve R50564 R50564 R50564 1
D Body R50524 R50534 R50544 1
E Silencer R50560 R50560 R50560 1
F Screw Pack R50567 R50567 R50567 9
G Venturi Tube R50563 R50563 R50563 1
H Venturi R50528 R50538 R50548 1
J Diffuser R50526 R50536 R50546 1
K Pump R50520 R50530 R50540 1
L Base R50525 R50535 R50545 1
M Rubber Pack R50566 R50566 R50566 1
N Pump Holder R50561 R50561 R50561 1
A
C
E
G
H
K
M
L
F
J
D
B
N
RED SEA REEFER™ Skimmer
10
Assembly
Remove the components from the protective packaging and familiarize
yourself with them.
Note: The skimmer body has been assembled in a unique position for
transportation purposes only.
Placement & Orientation:
The REEFER Skimmers are designed to allow 3 distinct orientations of
the venturi pump inlet relative to the Skim regulator (left/center/right)
enabling the skimmer to be customized for the specic layout of your
sump. There must be at least 2.5cm (1”) of unobstructed water column in
front of the venturi inlet. There must be at least 2.5cm (1”) of free space
above the collection cup to allow it to be removed for cleaning.
The collection cup can be freely rotated so that the FoamView window
can be set to whatever angle is best for you when regulating the skimmer.
Unscrew the skimmer body from the base and if necessary reposition the
pump holder to suit the desired orientation of the pump inlet. Turn the
skimmer base upside-down and push the rubber feet rmly into position.
.
ENG
11
Skimmer Regulator - Rotating the regulator in the “Minus” direction will
increase the opening in the base, lowering the foaming point or to produce
a drier foam. Rotating in the “Plus” direction decreases the opening in the
base, raising the foaming point or to produce a wetter foam.
Skimmer pumps need to be cleaned on a regular basis to remove calcium
and other deposits and therefore it is recommended to familiarize yourself
with the pump by disassembling/reassembling it before assembling it
for the rst time in the skimmer. Before pushing the pump into the pump
holder make sure that the rubber damper pad is in position.
Remove the cable restraint from the base.
Run the pump cable around the pump and insert it through
the cable channel and under the base.
Push the cable restraint back into position.
Note: Not using the cable restraint may affect the
regulation of the skimmer
Disassemble the bubble diffusion chamber and
temporarily position it above the pump. If necessary
reposition the return-ow plug so that it is above the regulated outlet
in the base (it is easier to do this before the diffusor is attached to
the pump). Secure the diffusor to the pump with the nut provided and
attach the diffusor plate with the center screw. Make sure that diffusor is
concentric with the base.Push the rubber connector onto the pump inlet.
RED SEA REEFER™ Skimmer
12
Familiarize yourself with the operation and assembly/
disassembly of the manual neck cleaner.
To operate the cleaner, use the handle recess in the lid to
rotate it either in the clockwise or anti-clockwise direction.
This may be slightly stiff when dry however it will rotate
easily when in regular use.
The lid/wiper can be removed as a single unit by pulling
it up and out of the foaming section of the neck.
Due to the conical shape of the foaming section a small
force may be required to reinsert the wiper/lid to the cup.
The wiper is held in the lid by snap connectors on both
sides of the handle and can be removed for cleaning.
Should it become necessary the wiper blades can also be
removed for more thorough cleaning and/or replacement.
With all of the internal components assembled, lower the skimmer body
onto the base so that the hole on the side is aligned with the pump inlet.
Secure the body in position tightly with the 4 screws provided.
Manual Neck Cleaner
The REEFER Skimmers are provided with an extra-long
drainage tube with an elbow connector and a watertight
valve. Push the rubber tube onto the drainage outlet at
the bottom of the collection cup and set the angle of the
elbow to give a convenient path for the drainage tube to
the front of your sump for easy periodic collection of the
accumulated waste.
Ensure that the O-ring is in position and assemble the collection cup by
pushing it down into the neck of the skimmer body. This will be easier if
the O-ring is wet.
ENG
13
Assemble the venturi by simultaneously pushing
and rotating it through the rubber grommet in
the wall of the skimmer body and into the rubber
connector that you previously put onto the pump
inlet. When fully inserted ensure that the venturi
air inlet is facing up. (This will be easier if you wet
the external surface of the venturi with water –
do not use any type of grease.)
Attach the air tube to the inlet of the silencer
making sure that the loop of the silencer drainage
port plug is in place. Also check that the drainage
port plug is properly inserted in the drainage port.
Click the silencer into its holder on the skimmer
neck and attach the free end of the air tube to
the venturi air inlet.
Installation:
Congratulations, your REEFER Skimmer is now fully assembled and ready
to be placed in the sump.
Read the following section about skimming and regulation before
switching on the pump.
Before placing the skimmer in the sump, rotate the skim regulator
fully in the minus direction. This will open the water outlet in the base
allowing sump water to more freely enter the skimmer body and
prevent it oating due to air trapped inside. This will also prevent over-
skimming on start-up.
The rubber feet hold the bottom of the skimmer 13mm (1/2”) above
the bottom of the sump therefore the power cable can safely be run
under the skimmer if it helps with your cable management.
Make sure that you prevent the power plug of the pump from getting
wet during initial placement or future maintenance of the skimmer in
the sump.
Check that there is at least 2.5cm (1/2”) of unobstructed water column
in front of the venturi inlet.
Check that the water height in the skimmer compartment of your sump
is correct for your model of skimmer.
For best results the water level in your skimmer chamber should be
maintained at a constant height. This is normally achieved when your
sump has an Automatic-Top-Off unit installed.
Check that there is at least 2.5cm (1”) of free space above the
collection cup to allow it to be removed for cleaning.
Find a convenient place at the front of the sump to place the valve of
the drainage tube.
Rotate the collection cup so that you have a clear line of sight to the
Foamview®.
Operation of the REEFERSkimmer
Skimmers produce foam as the protein from the water sticks to the
surface of the air bubbles giving them the structural rigidity they need
to ascend the neck of the skimmer and settle in the collection cup. Since
foam production is proportional to the density of organic material in the
aquarium water which varies over time, the foam point in the neck will
need to be adjusted to ensure an efcient removal of the proteins without
an excessive amount of seawater.
The REEFER Skimmers have a precision geared skim regulator for a very
ne control of the foam point ensuring high skimming efciency. Rotating
the regulator in the “Minus” direction lowers the foaming point in the neck
to produce a drier foam. Rotating in the “Plus” direction raises the foaming
..
Click
RED SEA REEFER™ Skimmer
14
point to produce a wetter foam.
Adjust the skim regulator so that the water level in the skimmer body is
approximately at the base of the neck. If the foam is too dry or it starts
to accumulate lower in the neck, gradually rotate the Skim Regulator
in the “Plus” direction until the desired foam consistency is achieved.
Alternatively, if the foam is too wet, gradually rotate the Skim Regulator in
the “Minus” direction.
New set-ups typically have a negligible amount of organic matter in the
water and therefore is may take some time for a skimmate to be produced.
New skimmers sometimes need a short break-in period of a few days
before they begin to function efciently. Over-skimming (an uncontrollable
ow of aerated water into the collection cup) is common while harmless
chemical residues that affect the surface tension of the water are
neutralized. In case of over-skimming rotate the regulator fully in the Minus
direction and allow the over-skimming to naturally reduce in intensity.
Feeding and Supplementing
Skimmers are very susceptible to the effect of surface-active compounds
such as foods and supplements that are added regularly to the aquarium.
Such materials can signicantly affect the foam production and in some
cases cause over-skimming. Immediately before adding such materials
switch the skimmer off and leave off for 30 minutes or however long it
takes until the skimmer will return to its normal foaming action without
repositioning the Skim Regulator.
Maintenance
Collection Cup
Monitor the amount of skimmate that accumulates in the collection cup
and drain the cup on a regular basis. Skimmer performance will benet
from using the neck cleaner on a daily basis and will enable you to only
remove and wash the cup and wiper every 7 – 10 days. If you wash the
cup with detergent make sure to rinse it thoroughly before returning it to
the skimmer.
Skimmer Pump & Impeller
Over time mineral and organic deposits will form inside the pump affecting
its performance and longevity. For best results it is recommended to
remove the pump from the skimmer once a month for cleaning.
Open the pump impeller chamber, pull out the impeller and rinse all parts
under the tap.
If you see any buildup of scale on the inside of the pump housing or on the
impeller magnet, use hot water or vinegar/scale remover to dissolve it.
Make sure that you rinse off all residues of any cleaning materials before
reassembling the pump.
ENG
15
Troubleshooting
Q. The bubbles in the skimmer are too large.
A. Ensure that you are using the skimmer in saltwater at the correct specic
gravity. Freshwater cannot be efciently skimmed using a protein skimmer.
Q. My skimmer is new (or just cleaned) and doesn't seem to be skimming.
A. If your skimmer is new, clean it with fresh water and rinse thoroughly
with hot water. Allow the skimmer to run for 48 hours to remove any
harmless residues from the production process. These materials are safe for
your aquarium, but impede the skimmer's ability to foam efciently for a
couple of days.
Q. My aquarium is full of micro bubbles or air mist.
A. All skimmers release some air bubbles to the sump and therefore it is
best to have a bubble trap between the skimmer chamber and the return
pump. If your skimmer is new allow a few days for the skimmer to settle
in.
Tip: You might be getting micro bubbles if you are using tap water with
water conditioners or natural seawater. Many conditioners/impurities found
in natural seawater increase the surface tension of the water and cause a
small proportion of the bubbles to escape the skimmer chamber.
Q. My skimmer is producing a lot of weak, watery foam.
A. Rotating the regulator in the “Minus” direction lowers the foaming point
in the neck to produce a drier foam.
Tip: Production of an excessive amount of weak, watery foam is also
referred to as over-skimming. This often indicates the presence of chemical
substances that need to be removed by the skimmer. Many water
conditioners/impurities found in natural seawater increase the surface
tension of the water and cause serious over-skimming.
Tip: If you are using natural seawater, you should be aware that most
seawater today contains traces of pollutants, e.g. phenols, carbohydrates,
oils, etc.
Therefore, natural seawater is not recommended for use in reef aquaria.
We strongly recommend NOT using tap water. If you intend to use it,
however, DO NOT add conditioners/de-chlorinators. Instead, allow the
water to settle for 24 hours for the chlorine to evaporate naturally before
introducing it to the aquarium.
Tip: Some brands of synthetic salt contain binding substances, such as
EDTA, that increases surface tension and causes over-skimming.
Q. There is a reduction in the quantity of air bubbles in my skimmer.
A. Check for blockages in the silencer, air tube or venturi. If the problem
persists, clean the skimmer pump.
Q. I cannot regulate my skimmer.
A. Check that the water level in skimmer chamber of your sump is as
recommended. Try raising or lowering the water level by approximately
12mm (1/2”). Check that the water outlet on the bottom of the skimmer
has not become blocked. Clean the skimmer pump.
Q. The aspiration pump is making a rattling noise.
A. Clean the skimmer pump and check for damage to the impellor.
Q. The skimmer is making a gurgling noise.
A. There may be water trapped in the silencer. Remove the drain plug and
let out any accumulated water. Remember to return the plug.
RED SEA REEFER™ Skimmer
16
Warranty
Red Sea Fish Pharm Aquarium Products Limited Warranty
The limited warranty sets forth all Red Sea Fish Pharm Ltd (Red Sea)
responsibilities regarding this product. There are no other express or
implied warranties from Red Sea. Red Sea warrants your product against
defects in materials and workmanship for a period of 24 months, valid from
the date of original purchase and will repair this product free of charge (not
including shipping costs) with new/rebuilt parts. The precondition for the
warranty is that the stipulated set- up routine is observed. In the event that
a problem develops with this product during or after the warranty period,
contact your local dealer or Red Sea (at the company address indicated) for
details of your nearest authorized service center.
The warranty is extended only to the original purchaser. Proof of date of
purchase will be required before warranty performance is rendered. This
warranty only covers failures due to defects in materials or workmanship
which occur during normal use. It does not cover damage which occurs in
shipment or failures which result from misuse, abuse, neglect, improper
or service by anyone other than an authorized Red Sea service center. Red
Sea shall not be liable for incidental or consequential damages resulting
from the use of this product, or arising out of any breach of this warranty.
All express and implied warranties, including the warranties of salability
period set forth above. These statements do not affect the statutory rights
of the consumer. USA Some states do not allow the exclusion or limitation
of incidental or consequential damages, or limitations on how long an
implied warranty lasts, so the above exclusion or limitations may not apply.
ENG
17
RED SEA REEFER™ Skimmer
18
1/84