INSTRUCTION MANUAL
GP BLUESTREAK 800
*SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
No. 41901
REQUIRED FOR OPERATION
BEFORE YOU BEGIN
RADIO PREPARATION
ASSEMBLY
OPERATING YOUR MODEL SAFELY
HOW TO HANDLE ENGINE POWERED BOATS
SPARE PARTS & OPTIONAL PARTS
2
2 3
3
4 19
20
21 23
24
INDEX
Before commencing assembly, please read these instructions thoroughly!
LENGTH : 930mm
THE FINEST RADIO CONTROL MODELS
R
SAFETY PRECAUTIONS
This radio control model is not a toy!
First-time builders should seek advice from people having building
experience in order to assemble the model correctly and to produce
its performance to full extent.
Assemble this kit only in places out of childrenÕs reach!
Take enough safety precautions prior to operating this model.
You are responsible for this modelÕs assembly and safe operation!
Always keep this instruction manual ready at hand for quick
reference, even after completing the assembly.
RADIO CONTROLLED .16 ENGINE POWERED RACING BOAT
GPVERSION
TOOLS REQUIRED
Sharp Hobby KnifePhillips Screwdriver (L.M.S) Needle Nose Pliers
Awl
Scissors
Wire Cutters
Instant Glue
Epoxy Glue
Sand Paper
1
Read through the manual before you begin, so
you will have an overall idea of what to do.
1 BEFORE YOU BEGIN (1)
Check all parts. If you find any defective or missing parts,
contact your local dealer or our Kyosho Distributor.
2
3
Symbols used throughout the instruction manual, comprise:
Do not do that!
REQUIRED FOR OPERATION
Apply epoxy glue.
Apply instant glue (CA glue, super glue).
Apply grease.Assemble as many times as specified
(here: twice).
x2
Assemble left and right sides the
same way.
Must be purchased separately!
Tentatively tighten.
Cut off excess.
Drill holes with the specified diameter
(here: 2mm).
Ensure smooth non-binding movement
while assembling.
Pay close attention here!
Assemble in the specified order.
2mm
Do not overlook this symbol!
Warning!
Epoxy A
Epoxy B
Silicone Glue
SILICONE
Cut off shaded portion.
1
2
2 channel radio
3 8
AA-size Batteries
(For Transmitter) 8 pcs.
For proper radio handling, refer to its manual.
2 2
2 channel & 2 servo radio for R/C models, and battery box.
2
Required for engine starting:
3
Fuel-proof paint
Battery Box
AAAAAA
4
AA-size Batteries
(For Receiver) 4 pcs.
If already supplied with the radio,
there is no need to purchase a battery
box separately.
( )
Explanations on the radio are based on the FUTABA radio.
WARNING: Gasoline
or kerosene cannot
be used.
Glow Fuel &
Fuel Pump
Plug Wrench
HANDY
FUEL
No.73301
Booster Cord
If you are using your own radio, ensure its servos correspond in size
to the servos in the diagram below.
< Suitable servo dimensions >
With any other radio:
KYOSHO SPRAY COLOR
No.76301 76403
CAUTION: Before using spray colors,
always read their explanations!
S
P
R
A
Y
C
O
L
O
R
R
K
Y
O
S
H
O
S
P
R
A
Y
C
O
L
O
R
R
K
Y
O
S
H
O
If greater fuel resistance is required, use a urethane paint.
Fuel Pump
2
2 BEFORE YOU BEGIN (2)
5
The threads are stripped.Overtightened.
4
How size of screw is given:
Screw
3mm
12mm
TP
Self-tapping (TP) screws cut threads into the parts
when being tightened. Excessive force may
permanently damage parts when tightening TP
screws. It is recommended to stop tightening when
the part is securely attached or when some resistance
is felt after the threaded portion enters the plastic.
This kit contains many screws in and other hardware
different metric sizes and shapes. For your reference,
the figures in the manual show actual sizes. (Some
screws are extras.)
CH-2 CH-1
BATT.
RADIO PREPARATION
Set up a radio control system as indicated below.
1
Plug in connectors.
2
Install the AA-size batteries.
3
Extend the transmitter antenna. If not, the
range of the transmitter will not be sufficient!
4
Undo the receiver antenna. If not, the
range of the receiver will not be sufficient!
5
Center all trims. (Transmitter)
6
Switch on. (Transmitter)
7
Switch on. (Receiver)
8
Check that the servos move according
to your inputs. (Transmitter)
10
Switch off. (Transmitter)
11
Retract the antenna. (Transmitter)
9
Switch off. (Receiver)
Antenna
Connector
Receiver
Connector
Rudder Stick
Rudder Servo
Speed Control Servo
Switch
Battery Box
CH.2
CH.1
BATT
Rudder Trim
Speed Control Stick
Speed Control Trim
For forward move-
ment & stop.
Adjust so boat will not
speed off at once.
Rudder Stick
In addition to this page, read the instruc-tion
manual supplied with your radio as well.
For steering (left and
right bends).
CH-2 CH-1
BATT.
CH-2 CH-1
BATT.
Rudder Trim
For adjusting straightline
running.
Speed Control Stick
Speed Control Trim
Battery Cover
Handle
Antenna
Switch
3
Types of screws:
Screw
Set Screw Cap ScrewSelf-tapping (TP) Screw
Pay close attention here!
Rudder
1
2
Note the direction.
Top
3x14mm
5
4
5
1
2
3
3mm
E-ring
E-ring
2
E3
E-ring
2
5 4 x 8mm
Metal Bushing
2
3mm
Nut
3 x 14mm
Screw
2
Rudder
3
1
2
Assemble in the specified order.
3
Rudder
52
52
6
7
6 8 9
10
8
9
10
4x4mm
4x4mm
0.5mm
Hex Wrench (2.0mm)
Note the direction.
Long Short
6
4 x 9 x 4mm
Collar
1
2
52
4 x 8x 3mm
Stainless Bearing
2
4 x 4mm
Set Screw
Firmly tighten the set screw onto the flat spot.
Apply grease.
Make sure that
there is no gap.
2.0mm
E3 E
E3 E
E
4
Pay close attention here!
Apply instant glue (CA glue, super glue).
4
Fuel Tank Mount
Fuel Tank
5
6
Engine Cowling
12
Cut off shaded portion.
5mm
32
Silicon Tube (130mm)
32
Silicon Tube (120mm)
38
Silicon Tube
34
35
36
39
40
Sponge Tape
21
Rubber Sheet
Abrade the glued surface
with sandpaper.
Glued surface should be free
from any oil residues and dirt.
Close gaps with CA adhesive.
Tighten the 5mm Nut and
make sure the movement
of to the directions as
arrows show.
Remove the flashing.
Remove the protective film.
Ensure smooth non-binding movement while assembling.
Drill holes with the specified diameter.
3mm
40
39
39
1
5mm
5mm Nut
1
Washer
34
3mm
3mm
5mm
5mm
120mm 130mm
32
Silicone Tube
Cut off.
51
11
39
130mm
120mm
11
3mm
5
Engine Mount
Engine Mount
7
8
12
13
14
15
16
16
16
16
17
18
Hex Wrench (2.5mm)
Hex Wrench (2.5mm)
3x10mm
3x10mm
3x10mm
3x10mm
3x6mm
3x6mm
2.6x25mm
1
1
2
1
1
1
1
2
2
2
2
3
4
4
Link to the bottom hole.
Pre-assembled.
Firmly tighten in step .
Note the direction.
4
3 x 10mm
Cap Screw
2
2.6 x 25mm
Cap Screw
Assemble in the specified order.
4
3 x 6mm
F/H Screw
4
Antivibration Rubber
16
Note the direction.
2mm
71
72
32
32
Drill holes with the specified diameter.
2mm
2mm
2.5mm
2.5mm
6
Pay close attention here!
Apply instant glue (CA glue, super glue).
9
Engine Mount
Assemble left and right sides the same way.
Cut off shaded portion.
Rubber Sheet
19
Abrade the glued surface
with sandpaper.
Glued surface should be free
from any oil residues and dirt.
Close gaps with CA adhesive.
20
19
Note the direction.
10
Radio Bpx
47
46
46
45
48
49
3x8mm
3x8mm
3x8mm
3 x 8mm
TP Screw
6
4
46
8 x 3 x 3.5mm
Collar
Note the direction.
Align with the top mark.
Align with the second mark
from the top.
21
Rubber Sheet
44
Abrade the glued surface
with sandpaper.
Glued surface should be free
from any oil residues and dirt.
Ensure smooth non-binding movement while assembling.
21
Close gaps with CA adhesive.
19
2
TP
44
7
Apply instant glue (CA glue, super glue).
Radio Box
12
4
3 x 8mm
TP Screw
3x8mm
3x8mm
52
Supplied with the servo.
Rudder
Servo
2mm
2mm
Use this hole.
8mm8mm
53
Drill holes with the specified diameter.
3mm
Must be purchased separately!
13
Radio Box
54
54
52
54
54
54
54
5
54
Cap
Cut off shaded portion.
Radio Box
11
Sponge Tape
51
1
50
Antenna Grommet
Apply sponge tape
around the entire rim,
leaving no gaps.
Sponge Tape
51
50
50
3mm
TP
8
Radio Box
14
Throttle servo.
5
3 x 8mm
TP Screw
55
3x8mm
3x8mm
3x8mm
15
Radio Box
Nylon Strap
60
Nylon Strap
60
Receiver
Battery Box
Antenna
Cut off excess.
Radio Box
16
<OFF>
OFF
ON
<ON>
Switch
1
66
O-ring P2
1
61
O-ring P5
Note the direction.
66
67
66
65
61
62
63
64
61
65
Supplied with the switch.
2
3
1
Assemble in the specified order.
Must be purchased separately!
TP
O P2
O P5
9
Hex Wrench (1.5mm)
Hex Wrench (1.5mm)
Radio Box
17
Connect as per radio
instruction manual.
Switch
Supplied with
the servo.
13mm
18
Radio Box
Close. Open.
Cut off shaded portion. Drill holes with the specified diameter.
3mm
Must be purchased separately!
2mm
Nylon Nut
2
3 x 3mm
Set Screw
1
23
Rod Stopper
1
22
23
23
3mm
10mm
3x3mm
24
24
22
22
3x3mm
3x3mm
2mm
2mm
Assemble left and right sides the same way.
1.5mm
1.5mm
3mm
10
Apply instant glue (CA glue, super glue).
19
Hull
20
Hull
21
Hull
27
28
29
30
26
4x4mm
Hex Wrench (2.0mm)
1
4 x 4mm
Set Screw
26
2
Rod Guide
37
Linkage Post
33
1
4 x 4mm
Set Screw
4x4mm
Hex Wrench (2.0mm)
33
27 28
4x4mm
37
37
3x12mm
3x12mm
2mm
2mm
3 x 12mm
TP Screw
4
2
2mm
Nylon Nut
2
2.6mm
Nut
2
2.6 x 8mm
Screw
Apply grease. Tentatively tighten.Ensure smooth non-binding movement while assembling.
27
29
4x4mm
Firmly tighten the set screw onto
the flat spot.
Firmly tighten the set screw onto
the flat spot.
2.6x8mm
2.6mm
A-5
2
2.0mm
2.0mm
TP
11
Hull
22
23
Hull
29
Abrade the glued surface
with sandpaper.
After positioning, pour instant
glue into the space around .
Close gaps with CA adhesive.
Close gaps with CA adhesive.
Make sure that runs parallel
to the center line of the boat.
21
21
28
Bottom
<
CHECK 2
> <
CHECK 3
> <
CHECK 4
><
CHECK 1
>
4mm
12mm
28
Make sure that there
is no gap.
21
Glued surface should be free
from any oil residues and dirt.
Don't pour instant glue at here.
21
Apply instant glue (CA glue, super glue). Pay close attention here!
Assemble left and right sides the same way.
2mm
29
21
CHECK1 4
21
28
12
Pay close attention here!
Apply instant glue (CA glue, super glue).
24
Hull
25
Hull
Assemble left and right sides the same way.
185mm
1
3
3
Make sure the position is correct;
then, glue into place.
Bottom
21
Abrade the glued surface with sandpaper.
Make sure that there is no gap.
Glued surface should be free
from any oil residues and dirt.
2
Abrade the glued surface with sandpaper.
Glued surface should
be free from any oil
residues and dirt.
50mm
50mm
Make sure the position is
correct; then, glue into place.
Radio Box
19
40
11
11
19
11
11
Assemble in the specified order.
21
Close gaps with CA adhesive.
Close gaps with CA adhesive.
13
Hull
26
27
Hull
45
45
41
28
28
41
41
12mm
33
Note the direction.
Abrade the glued surface
with sandpaper.
Apply instant glue (CA glue, super glue).Pay close attention here! Cut off shaded portion. Apply epoxy glue.
1
2
3
2
1
3
2
Assemble in the specified order.
28
41
14
28
Hull
29
29
29
Painting
Assemble left and right sides the same way.
Be sure to paint using a fuel proof
paint. Leaving unpainted may result
in damage.
4
3 x 12mm
TP Screw
1
4 x 4mm
Set Screw
20
29
29
1
1
2
3
2
3
5
3x12mm
3x12mm
Assemble in the specified order.
4x4mm
28
30
58
59
Hex Wrench (2.0mm)
4
27
Remove the rudder, drive shaft and engine.
Re-install them after painting in step .
Pay close attention here!
TP
30
30
59
28
28
2.0mm
Wash the parts with a synthetic detergent
and dry them well. Then, cover with
masking tape on both ends of to keep
out paint.
58
58 59
Paint with a fuelproof paint. Paint the
inside of and the backs of & .
Re-install the rudder, drive shaft and engine .
Masking Tape
15
Hull
30
31
Hull
460mm
32
Silicone Tube
Silicone Tube
(140mm)
Cut off.
140mm
32
Silicone Tube
Cut off.
1
31
Pipe Joint
25
3mm
Grommet
2
32
25
25
32
52
60
31
Silicone Tube (460mm)
2
3 x 3mm
Set Screw
3x3mm
69
1
2
2
3
Adjust the angle as
shown, and then tighten
the set screws.
B
A
Hex Wrench (1.5mm)
A
=
B
Apply instant glue (CA glue, super glue). Cut off excess.
Assemble in the specified order.
Assemble left and right sides the same way.
45
Tighten the 3x12 TP Screws and make sure the
easy movement of rudder to the directions as arrows show.
3x12mmTP 4
3x12mm
3x12mm
Ensure smooth non-binding movement while assembling.
140mm
460mm
1.5mm
16
Apply instant glue (CA glue, super glue).
32
Hull
33
Hull
Assemble left and right sides the same way.
130mm
5mm
32
Silicone Tube
Cut off.
Fix with silicon sealant.
31
32
25
68
4x4mm
Firmly tighten the set screw onto
the flat spot.
4x4mm
19
Hex Wrench
(2.0mm)
25
31
57
Silicone Tube
(5mm)
32
Silicone Tube
(460mm)
Silicone Tube
(130mm)
32
11
11
40
42
42
40
Rubber Band
Place as shown.
40
Cut off excess.
32
68
56
60
25
1
1
31
Pipe Joint
2
4 x 4mm
Set Screw
3mm
Grommet
31
68
2.0mm
5mm
130mm
460mm
17
Radio
34
Round off
corners.
Apply instant glue (CA glue, super glue).
35
Cabin
Pay close attention here!
Hull
36
43
43
2.6x8mm
1mm
70
71
70
Body Pin
1
70
Bend
Stand
2
2.6 x 8mm
TP Screw
59
58
59
58
1
3 x 3mm
Set Screw
Do not do that!Cut off shaded portion.
15
24
Hex Wrench
(1.5mm)
3x3mm
With the throttle stick in neutral. With the throttle stick pushed up.
"Astern" cannot be used.
Adjust the tightening position
of as shown above.
See the radio instruction
manual, too.
Abrade the glued surlace
with sandpaper.
15
10
mm
Drill holes with the specified diameter.
6mm
TP
1.5mm
15
6mm
18
Adjust Running
38
Adjusting the running posture and the speed by adjusting the angle of propeller.
Wind : light
Waves : low
Wind : strong
Waves : high
Bow will be up.
Bow will be down.
Decals
37
Decals with no number apply any place.
The decal numbers between brackets are only for the opposite side.
Apply the decals to the spots indicated.
R
23 11 21 33
5 7 1
27
3
25 31
9
4634
22
14
17
19 47
15
18
2048
16
10 32
4 6
26
2
24 30
8
35
( )
44 45
( )
38 39
( )
36 37
( )
42 43
( )
12 13
( )
28 29
( )
40 41
Make sure that there is no gap.
Adjust the angle by loosening the 3x14 screws.
Bow will be up.
Standard position.
Bow will be down.
Do not adjust the rudder beyond this point.
3x14mm
19
Always check the dry batteries in the radio!
When the radio batteries get weak, transmission and reception
decrease. You may lose control of your model when operating
it with weak radio batteries. This may lead to accidents!
Operate the model in spacious areas with no people
around! Do NOT operate it:
1. in places where children and many people gather!
2. in swollen rivers!
3. in rivers, lakes and other places
with strong currents!
*
Non-observance may account
for personal injury and
property damage!
When the model is behaving strangely . . .!
Immediately stop the model and check the reason. As long as the
problem is not cleared, do NOT operate it! This may lead to further
trouble and unforeseen accidents!
05
Handle fuel ONLY
outdoors!
Vapors and exhausts are
very noxious to health!
Fuel is highly inflammable and
high-explosive!
1. NEVER use fuel indoors or in places
with open fires and sources of heat!
2. Store fuel ONLY in cool, dry and dark
places out of childrenÕs reach! Tightly shut the cap!
3. Do NOT dispose of empty fuel cans into a fire! There is
danger of explosion!
NEITHER swallow fuel NOR let it into your eyes!
Immediate measures
should be taken:
if fuel is swallowed, in--
duce vomit-ing. If fuel
gets into eyes, rinse
them and consult an
orphamologist!
Do NOT put fingers or any objects inside
rotating and moving parts!
Rotating and moving at
high speed, you may be
seriously injured touching
them!
ONLY use glow fuel for radio control models!
Because the use of gasoline and kerosene in R/C models ac--
counts for fires, NEVER use them!
Right after use, do NOT
touch equipment on the
model such as the engine
and muffler, because they
generate high temperatures!
WARNING: Do NOT operate the model in the following places and situations:
(Non-observance may lead to accidents!)
WARNING: in order to avoid accidents and personal injury,
be sure to observe the following:
Keep in mind that people around you may also
operate a radio control model!
NEVER share the same frequency
with somebody else at the same
time! Signals will be mixed and
you will lose control of your model.
This may lead to accidents!
PROHIBITED
PROHIBITED
PROHIBITED
You may burn yourself seriously touching them!
PROHIBITED
OPERATING YOUR MODEL SAFELY
20
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
/
