Tascam MZ-123BT 取扱説明書

ENGLISH

FRANÇAIS

ESPAÑOL

DEUTSCH

ITALIANO

日本語

OWNER'S MANUAL

MODE D’EMPLOI

MANUAL DEL USUARIO

BEDIENUNGSANLEITUNG

MANUALE DI ISTRUZIONI

取扱説明書

OPZM100TEA04

MZ-123BT

INSTALLATION MIXER

2 TASCAM MZ-123BT

• TASCAMisaregisteredtrademarkofTEACCorporation.

• TheBluetooth®wordmarkandlogoarethepropertyof

BluetoothSIG,Inc.andareusedbyTEACCorporationwith

permission.

• QualcommaptXisaproductofQualcommTechnologies,Inc.

and/oritssubsidiaries.

• QualcommisatrademarkofQualcommIncorporated,

registeredintheUnitedStatesandothercountries.aptXis

atrademarkofQualcommTechnologiesInternational,Ltd.,

registeredintheUnitedStatesandothercountries.

• Othercompanynames,productnamesandlogosinthis

documentarethetrademarksorregisteredtrademarksof

theirrespectiveowners.

TEACCORPORATION

https://tascam.jp/jp/

Phone:+81-42-356-9143

1-47Ochiai,Tama-shi,Tokyo206-8530Japan

TEACAMERICA,INC.

https://tascam.com/us/

Phone:+1-323-726-0303

10410PioneerBlvd.Suite #1SantaFeSprings,California90670,

U.S.A.

TEACUKLtd.

https://www.tascam.eu/en/

Phone:+44-1923-797205

MeridienHouse,69-71ClarendonRoad,Watford,Herts,WD17

1DS,UnitedKingdom

TEACEUROPEGmbH

https://www.tascam.eu/de/

Phone:+49-611-71580

Bahnstrasse12,65205Wiesbaden-Erbenheim,Germany

TEACSALES&TRADING(SHENZHEN)CO.,LTD

https://tascam.cn/cn/

Phone:+86-755-88311561~2

Room817,XinianCenterA,TairanNineRoadWest,Shennan

Road,FutianDistrict,Shenzhen,GuangdongProvince518040,

China

TASCAM MZ-123BT 3

IMPORTANT SAFETY INSTRUCTIONS

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO

USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within equilateral triangle, is intended to alert the

user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may

be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence

of important operating and maintenance (servicing) instructions in the literature accompanying

the appliance.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT

EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

For U.S.A.

Declaration of Conformity

Model Number: MZ-123BT

Trade Name: TASCAM

Responsible party: TEAC AMERICA, INC.

Address: 10410 Pioneer Blvd. Suite #1, Santa Fe Springs,

California 90670, U.S.A.

Telephone number: 1-323-726-0303

This device complies with Part 15 of the FCC Rules. Operation

is subject to the following two conditions: (1) this device may

not cause harmful interference, and (2) this device must accept

any interference received, including interference that may

cause undesired operation.

INFORMATION TO THE USER

This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful

interference to radio communications. However, there is

no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference

to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to

try to correct the interference by one or more of the following

measures.

a) Reorient or relocate the receiving antenna.

b) Increase the separation between the equipment and

receiver.

c) Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

d) Consult the dealer or an experienced radio/TV technician

for help.

CAUTION

Changes or modifications to this equipment not expressly

approved by TEAC CORPORATION for compliance could void

the user’s authority to operate this equipment.

IN USA/CANADA, USE ONLY ON 120 V SUPPLY.

For Canada

THIS CLASS B DIGITAL APPARATUS COMPLIES WITH CANADIAN

ICES-003.

CET APPAREIL NUMERIQUE DE LA CLASSE B EST CONFORME A

LA NORME NMB-003 DU CANADA.

This product complies with the European

Directives request and the other Commission

Regulations.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance

with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat

registers, stoves, or other apparatus (including amplifiers)

that produce heat.

9. Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades with

one wider than the other. A grounding type plug has two

blades and a third grounding prong. The wide blade or the

third prong are provided for your safety. If the provided

plug does not fit into your outlet, consult an electrician for

replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the

point where they exit from the apparatus.

11. Only use attachments/accessories specified by the

manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table

specified by the manufacturer, or sold with the apparatus.

When a cart is used, use caution when moving the cart/

apparatus combination to avoid injury from tip-over.

OWNER’S MANUAL

4 TASCAM MZ-123BT

13. Unplug this apparatus during lightning storms or when

unused for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing

isrequired when the apparatus has been damaged in any

way, such as power-supply cord or plug is damaged, liquid

has been spilled or objects have fallen into the apparatus,

the apparatus has been exposed to rain or moisture, does

not operate normally, or has been dropped.

• The apparatus draws nominal non-operating power from the

AC outlet with its POWER or STANDBY/ON switch not in the

ON position.

• The mains plug is used as the disconnect device, the

disconnect device shall remain readily operable.

• Caution should be taken when using earphones or

headphones with the product because excessive sound

pressure (volume) from earphones or headphones can cause

hearing loss.

• If you are experiencing problems with this product, contact

TEAC for a service referral. Do not use the product until it has

been repaired.

WARNING

• Products with Class ! construction are equipped with a

power supply cord that has a grounding plug. The cord of

such a product must be plugged into an AC outlet that has

a protective grounding connection.

WARNING

• To prevent possible hearing damage, do not listen

at high volume levels for long periods.

CAUTION

• Do not expose this apparatus to drips or splashes.

• Do not place any objects filled with liquids, such as vases,

on the apparatus.

• Do not install this apparatus in a confined space such as a

book case or similar unit.

• The apparatus should be located close enough to the AC

outlet so that you can easily grasp the power cord plug at

any time.

• If the product uses batteries (including a battery pack

or installed batteries), they should not be exposed to

sunshine, fire or excessive heat.

• CAUTION for products that use replaceable lithium

batteries: there is danger of explosion if a battery is

replaced with an incorrect type of battery. Replace only

with the same or equivalent type.

RACK-MOUNTING THE UNIT

Use the supplied rackmount screw kit to mount the unit in a

standard 19-inch rack, as shown below.

ATTENTION

iLeave 1U of space above the unit for ventilation.

iAllow at least 10 cm (4 in) at the rear of the unit for

ventilation.

For European Customers

Disposal of electrical and electronic equipment and

batteries and/or accumulators

(a) All electrical/electronic equipment and waste batteries/

accumulators should be disposed of separately from the

municipal waste stream via collection facilities designated

by the government or local authorities.

(b) By disposing of electrical/electronic equipment and

waste batteries/accumulators correctly, you will help save

valuable resources and prevent any potential negative

effects on human health and the environment.

(c) Improper disposal of waste electrical/electronic equipment

and batteries/accumulators can have serious effects on the

environment and human health because of the presence

of hazardous substances in the equipment.

(d) The Waste Electrical and Electronic Equipment

(WEEE) symbols, which show wheeled bins that

have been crossed out, indicate that electrical/

electronic equipment and batteries/accumulators

must be collected and disposed of separately from

household waste.

(e) Return and collection systems are available to end users.

For more detailed information about the disposal of old

electrical/electronic equipment and waste batteries/

accumulators, please contact your city office, waste

disposal service or the shop where you purchased the

equipment.

TASCAM MZ-123BT 5

Wireless equipment precautions

Compliance of radio transmitter and

interference

This product has the function of broadband transmitter using

2.4GHz Band.

Use frequency range: 2400 MHz - 2480 MHz

Maximum output power: Bluetooth® Class 2 (less than 2.5

mW) Please use only in the country where you purchased the

product. Depending on the country, restrictions on the use of

Bluetooth wireless technology might exist.

Model for USA

Declaration of Conformity

Responsible party: TEAC AMERICA, INC.

Address: 10410 Pioneer Blvd. Suite #1, Santa Fe

Springs, California 90670, U.S.A.

Telephone number: 1-323-726-0303

This device complies with Part.15 of FCC Rules. Operation is

subject to the following two conditions: (1) this device may

not cause harmful interference, and (2) this device must accept

any interference received, including interference that may

cause undesired operation.

Labeling of authorization

FCC ID: XEG-MZ123BT

Model for Canada

Compliance of radio transmitter

This device complies with Industry Canada’s licence-exempt

RSSs.

Operation is subject to the following two conditions:

1) This device may not cause interference

2) This device must accept any interference, including

interference that may cause undesired operation of the

device.

Labeling of authorization

IC: 1559C-MZ123BT

Modèle pour le Canada

Conformité de l’émetteur radio

Ce dispositif est conforme à la norme CNR-210 d’Industrie

Canada applicable aux appareils radio exempts de licence. Son

fonctionnement est sujet aux deux conditions suivantes:

1)

Le dispositif ne doit pas produire de brouillage préjudiciable, et

2) Ce dispositif doit accepter tout brouillage reçu, y compris

un brouillage susceptible de provoquer un fonctionnement

indésirable.

Référence d’autorisation

IC: 1559C-MZ123BT

Compliance of interference

This Class B digital apparatus complies with Canadian ICES-003.

This equipment complies with FCC/IC radiation exposure

limits set forth for an uncontrolled environment and meets

the FCC radio frequency (RF) Exposure Guidelines and RSS-102

of the IC radio frequency (RF) Exposure rules. This equipment

has very low levels of RF energy that it deemed to comply

without maximum permissive exposure evaluation (MPE). But

it is desirable that it should be installed and operated keeping

the radiator at least 20 cm or more away from person’s body

(excluding extremities: hands, wrists, feet and ankles).

Conformité de brouillage

Cet appareil numérique de la classe B est conforme à la norme

NMB-003 du Canada.

Cet équipement est conforme aux limites d’exposition au

rayonnement fixées par la FCC/IC pour un environnement non

contrôlé, et répond aux Directives d’exposition aux fréquences

radio (RF) de la FCC et aux Règles CNR-102 d’exposition aux

radiofréquences de l’IC. Cet équipement émet une énergie

RF très faible qui est considérée conforme sans évaluation de

l’exposition maximale autorisée. Cependant, cet équipement

doit être installé et utilisé en gardant une distance de 20 cm ou

plus entre le dispositif rayonnant et le corps (à l’exception des

extrémités : mains, poignets, pieds et chevilles).

Référence d’autorisation

CAN ICES-3(B)/NMB-3(B)

Model for EEA (European Economic Area)

Hereby, TEAC Corporation declares that the

radio equipment type is in compliance with

Directive 2014/53/EU., and the other Directives,

and Commission Regulations.

The full text of the EU declaration of conformity is available at

the following internet address: Please contact us by e-mail.

https://www.tascam.eu/en/kontakt.html

EU Importer: TEAC Europe GmbH

Bahnstrasse 12, 65205 Wiesbaden-Erbenheim, Germany

Radiation Exposure requirements

This equipment meets the regulation, which is recognized

internationally, for the case of human exposure to radio waves

generated by the transmitter.

Statement of compliance

Model for USA

This equipment complies with FCC radiation exposure limits set

forth for an uncontrolled environment and meets the FCC radio

frequency Exposure Guidelines.

Model for Canada

This equipment complies with IC RSS-102 radiation exposure

limits set forth for an uncontrolled environment.

Model for USA/Canada

This Class B digital apparatus complies with Canadian ICES-003.

This equipment complies with FCC/IC radiation exposure

limits set forth for an uncontrolled environment and meets

the FCC radio frequency (RF) Exposure Guidelines and RSS-102

of the IC radio frequency (RF) Exposure rules. This equipment

has very low levels of RF energy that it deemed to comply

without maximum permissive exposure evaluation (MPE). But

it is desirable that it should be installed and operated keeping

the radiator at least 20 cm or more away from person’s body

(excluding extremities: hands, wrists, feet and ankles).

Model for EEA (European Economic Area)

This equipment complies with EN.62311; Assessment of

electronic and electrical equipment related to human exposure

restrictions for electromagnetic fields; the harmonised standard

of DIRECTIVE 2014/53/EU.

6 TASCAM MZ-123BT

Introduction

Thank you very much for purchasing the TASCAM MZ-123BT.

Before using this unit, read this Owner’s Manual carefully so that

you will be able to use it correctly and enjoy working with it for

many years. After you have finished reading this manual, please

keep it in a safe place for future reference.

You can also download this Owner’s Manual from the TEAC

Global Site (http://teac-global.com/).

Features

pRackmount mixer that enables assignment of background

music and mic announcements to three zones

pProvides convenient background music playback setup

oBuilt-in Bluetooth® receiver enables music input from

smartphones, tablets and other devices

oBuilt-in AUX input enables music input from portable

music players and other devices that do not support

Bluetooth®

pNecessary controls for daily use have been carefully selected

and placed on the front, making operation also easy for

endusers

pThe Bluetooth® antenna on the front makes stable Bluetooth®

connection possible even in environments with many

obstacles

pDifferent input sources can be assigned to each of the three

sets of outputs

oEach output has a mono/stereo switch 1

oEuroblock terminals are ideal for permanent installations

pThree sets of line input channels

oChannel 1: line input (RCA, unbalanced)

oChannel 2: line input (RCA, unbalanced)

oChannel 3: AUX input/Bluetooth® 2

pTwo mic input channels ideal for announcements

oMic 1 can be connected to the XLR/TRS combo jack on

the front or the Euroblock terminal for installed use on the

back

oTalkover function automatically lowers background music

volume according to mic volume

oFlexible audio tone adjustment is possible using the

3-band equalizer and high-pass filter

o+48V phantom power supported

pHeadphone jack can be used to monitor every output

pCompact 1U rackmount size

1 When mono output is selected, a stereo input source will

be output as a mono mix.

2 During operation, select AUX input or a Bluetooth® source.

Contents

IMPORTANT SAFETY INSTRUCTIONS ..................................... 3

Wireless equipment precautions ........................................... 5

Introduction ............................................................................. 6

Features .................................................................................... 6

Included items ......................................................................... 7

Conventions used in this manual ........................................... 7

Precautions for placement and use ........................................ 7

Notes about power supply ...................................................... 7

Beware of condensation ......................................................... 7

Cleaning the unit ..................................................................... 7

Bluetooth® ................................................................................ 7

Profiles .........................................................................................................7

Codecs .........................................................................................................7

Content protection .................................................................................8

Transmission security ............................................................................. 8

Using the TEAC Global Site ..................................................... 8

Product registration ................................................................ 8

About TASCAM customer support service ............................. 8

Names of parts ......................................................................... 9

Front panel ................................................................................................. 9

Rear panel ................................................................................................ 11

Preparation ............................................................................ 12

Connecting Euroblock plugs ............................................................ 12

Attaching the Bluetooth antenna ................................................... 12

Connecting other equipment ............................................... 13

Connecting microphones .................................................................. 14

Connecting electronic devices and other audio equipment

.. 14

Connecting headphones ................................................................... 14

Connecting stereo amplifiers ........................................................... 14

Connecting with Bluetooth devices .............................................. 14

Turning the power on and off ...............................................15

Operation procedures ........................................................... 15

Adjusting line input channels 1-2 ................................................... 15

Adjusting the input of a mic connected to a mic input

connector (rear panel) ........................................................................ 15

Adjusting input from the mic connected to the front INPUT

jack ............................................................................................................. 15

Output channels ................................................................................... 16

Using the talkover function .............................................................. 16

Monitoring .............................................................................................. 16

Troubleshooting .................................................................... 16

Specifications .........................................................................17

Audio inputs ........................................................................................... 17

Audio outputs ........................................................................................ 17

Audio performance .............................................................................. 18

Bluetooth ................................................................................................. 18

Other ......................................................................................................... 18

TASCAM MZ-123BT 7

Included items

This product includes the following items.

Take care when opening the package to avoid damaging the

items. Keep the box and packing materials for transportation in

the future.

Please contact the store where you purchased this unit if any

of these items are missing or have been damaged during

transportation.

pMain unit ................................................................................................x 1

pPower cord set ......................................................................................x 1

pBluetooth antenna ..............................................................................x 1

pEuroblock plug .....................................................................................x 8

pCable band kit ......................................................................................x 1

pXLR cover ................................................................................................x 1

pRackmount screw kit ..........................................................................x 1

pOwner’s Manual (this document) including warranty ...........x 1

Conventions used in this manual

pComputers, portable audio devices and other equipment

connected to this unit using Bluetooth are called “Bluetooth

devices”.

pAs necessary, additional information is provided under TIP,

NOTE and CAUTION headings.

TIP

These are tips about how to use the unit.

NOTE

These provide additional explanations and describe special

cases.

ATTENTION

Failure to follow these instructions could result in damage to

equipment or lost data, for example.

VCAUTION

Failure to follow these instructions could result in injury.

Precautions for placement and use

pThe operating temperature range of this unit is 0 - 40 °C.

pDo not install this unit in the following types of locations.

Doing so could make the sound quality worse or cause

malfunction.

Places with significant vibrations

Next to a window or in another location exposed to direct

sunlight

Near heaters or other extremely hot places

Extremely cold places

Very humid or poorly ventilated places

Very dusty places

pTo enable good heat dissipation, do not place anything on

top of the unit.

pDo not place this unit on top of a power amplifier or other

device that generates heat.

Notes about power supply

pInsert the included power cord all the way into the AC IN

connector.

pDo not connect a power supply other than one that is

AC100V - 240V (50/60Hz).

pHold the power cord by its plug when connecting or

disconnecting it.

Beware of condensation

Condensation could occur if the unit is moved from a cold place

to a warm place, it is used immediately after a cold room has

been heated or it is otherwise exposed to a sudden temperature

change.

To prevent this, or if this occurs, let the unit sit for one or two

hours at the new room temperature before using it.

Cleaning the unit

Use a dry soft cloth to wipe the unit clean. Do not wipe

with chemical cleaning cloths, thinner, alcohol or other

chemical agents. Doing so could damage the surface or cause

discoloration.

Bluetooth®

This unit has a built-in Bluetooth audio receiver, and can input

sound played on a computer or portable audio device that

supports Bluetooth (Bluetooth device).

ATTENTION

The Bluetooth function of this unit is not guaranteed to

enable connection or operation with all Bluetooth devices.

Profiles

This unit supports the following Bluetooth profiles.

pA2DP (Advanced Audio Distribution Profile)

In order to transfer audio by Bluetooth, the Bluetooth device

must support A2DP.

Even if a Bluetooth device supports the same profiles, though,

its functions might differ according to its specifications.

Codecs

This unit supports the following codecs. It will automatically

select one of them during audio transfer.

pSBC

pAAC

pQualcomm®aptX ™ audio

The unit will select the appropriate codec to use according

to the codec compatibility of the other Bluetooth device and

communication conditions.

NOTE

iYou cannot select the codec to be used by pressing a

button,for example.

iDue to characteristics of Bluetooth wireless technology,

playback from this unit will be slightly delayed compared to

playback from the Bluetooth device.

8 TASCAM MZ-123BT

Content protection

This unit supports SCMS-T as a form of content protection when

transmitting audio, so it can play protected audio.

Transmission security

This unit supports security functions during Bluetooth

transmission in accordance with the Bluetooth standard

specifications, but it does not guarantee the privacy of such

transmissions.

TEAC CORPORATION will bear no responsibility should an

information leak occur during transmission by Bluetooth.

Using the TEAC Global Site

You can download updates for this unit from the TEAC Global

Site:

http://teac-global.com/

In the TASCAM Downloads section, select the desired language

to open the Downloads website page for that language.

Product registration

Customers in the USA, please visit the following TASCAM

website to register your TASCAM product online.

https://tascam.com/us/

About TASCAM customer support

service

TASCAM products are supported and warrantied only in their

country/region of purchase.

To receive support after purchase, on the TASCAM Distributors

list page of the TEAC Global Site (http:// teac-global.com/),

search for the local company or representative for the

region where you purchased the product and contact that

organization.

When making inquiries, the address (URL) of the shop or

web shop where it was purchased and the purchase date are

required.

Moreover, the warranty card and proof of purchase might also

be necessary.

TASCAM MZ-123BT 9

Names of parts

Front panel

1 INPUT jack

This is an XLR/TRS combo jack for mic input.

oXLR (1: GND, 2: HOT, 3: COLD)

oTRS (Tip: HOT, Ring: COLD, Sleeve: GND)

Use the INPUT GAIN knob (2) to set the input level.

To send the mic input from the front INPUT jack (1) to the

mic input channel, set the mic input channel 1 input source

switch (8) to FRONT LOW or FRONT HIGH.

2 INPUT GAIN knob

Use to adjust the mic input level from the INPUT jack (1).

3 Mic input OUTPUT SELECT switches/indicators

These select the mic buses to which the mic input sounds

from the rear mic input connectors (b) and the INPUT jack

(1) are sent.

The indicators for the selected outputs light.

4 Line input OUTPUT SELECT switches/indicators

These select the stereo busses to which the line input signals

from the rear line input connectors (l) and the AUX IN jack

(y) or a paired Bluetooth device are sent.

The indicators for the selected outputs light.

5 Monitoring switches/indicators

Use these to set whether signals are output from the PHONES

jack (d).

The indicators for the selected outputs light.

6 Bluetooth antenna connector

Connect the included Bluetooth antenna here.

7 POWER indicator

This shows the status of the unit.

When the POWER (g) switch on the back of the unit is on,

the POWER indicator lights.

8 Mic input channel 1 input source switch

Use this to select the input source for mic input channel 1.

This is set to REAR when shipped new from the factory.

Option Meaning

FRONT LOW

(PAD ON)

This selects input from the front INPUT jack

(1).

Use this setting when the connected mic

input level is high. (24dB attenuation)

FRONT HIGH

(PAD OFF)

This selects input from the front INPUT jack

(1).

REAR This selects input from the rear mic input

connector (b).

9 PHANTOM switch for the INPUT jack

Use this switch to supply +48V phantom power to the INPUT

jack (1) on the front of the unit.

The PHANTOM switch for the INPUT jack provides +48V

phantom power. (See “Connecting microphones” on page

14)

This is set to OFF when shipped new from the factory.

0 Mic input PEAK indicators

These light when signals from mic input channels 1-2 are

about to distort.

Adjust the rear mic GAIN knobs (c) so that the mic input

PEAK indicators do not light.

If a connected mic input level is high, set the PAD switches

(n) to ON, and then adjust the mic GAIN knobs (c).

When using INPUT jack (1), adjust the INPUT GAIN knob (2).

If the connected mic input level is high, set the mic input

channel 1 input selection switch (8) to FRONT LOW, and

then adjust the INPUT GAIN knob (2).

NOTE

Adjusting the mic input VOLUME knobs (w) will not change

the level that these light. Adjust the MIC gain knobs (c) or

the INPUT GAIN knob (2).

q Mic input signal (SIG) indicators

These light when signals are input through mic input

channels 1-2.

NOTE

Adjusting the mic input VOLUME knobs (w) will not change

the level that these light.

w Mic input VOLUME knobs

These adjust the levels of mic input channel 1-2 signals sent

to the mic bus.

NOTE

The thick line indicates approximately 0dB gain.

e Line input PEAK indicators

These light when signals from line input channels 1-2 are

about to distort (+3 dBV or higher).

Adjust the rear input GAIN knobs (k) so that the line input

PEAK indicators do not light.

NOTE

Adjusting the line input VOLUME knobs (t) will not change

the level that these light. Adjust the line input GAIN knobs

(k).

10 TASCAM MZ-123BT

r Line input signal (SIG) indicators

These light when signals are input through line input

channels 1-2.

NOTE

Adjusting the line input VOLUME knobs (t) will not change

the level that these light.

t Line input VOLUME knobs

These adjust the levels sent to the line input channel 1-2

stereo bus.

NOTE

The thick line indicates approximately 0dB gain.

y AUX IN jack (stereo mini jack)

This stereo mini jack is a line input jack.

Use this to connect with the line output jack of a tablet or

other external device.

VCAUTION

iBefore connecting another device to the AUX IN jack,

minimize the volume of that device. Failure to do so could

result in a sudden loud noise that could harm hearing, for

example.

iTurn the unit off before connecting or disconnecting with the

AUX IN jack.

u AUX IN - Bluetooth switch

This sets the input for line input channel 3 to the AUX IN jack

(y) or a Bluetooth device.

This is set to Bluetooth when shipped new from the factory.

NOTE

iThe input signal cannot be set to both the AUX IN jack (y)

and a Bluetooth device at the same time.

iSetting this switch to AUX IN will end connection with a

Bluetooth device.

iThis switch must be set to Bluetooth in order to pair with a

Bluetooth device.

iWhen this is set to Bluetooth, it will automatically try to

connect with the Bluetooth device to which it was previously

connected. In this case, pairing will automatically end if

connection is not possible because that Bluetooth device is

not turned on or its Bluetooth function is turned off.

i Analog output PEAK indicators

These light when signals output from the analog output jacks

(h) are about to distort (+20 dBu or higher).

Use the VOLUME knobs (p) to adjust so that the mic input

PEAK indicators do not light.

o Analog output signal (SIG) indicators

These light when sound is being output through the rear

analog output jacks (h).

p Line output VOLUME knobs

Use to adjust the output levels of the rear analog output

jacks (h).

NOTE

The thick line indicates approximately 0dB gain.

a PAIRING button and indicator

Press and hold this button to activate Bluetooth pairing

mode.

Press when pairing to end pairing. (See “Connecting with

Bluetooth devices” on page 14)

s PHONES VOLUME knob

Use this to adjust the headphone output level.

VCAUTION

Before connecting headphones, minimize the volume with

the PHONES knob. Failure to do so could result in a sudden

loud noise that could harm hearing, for example.

d PHONES jack

Use this standard stereo jack to connect stereo headphones.

Use an adapter to connect headphones with a mini plug.

TASCAM MZ-123BT 11

Rear panel

f AC IN connector

Connect the included power cord here.

g POWER switch

Press to turn the unit on and off.

When on, the POWER (7) indicator lights on the front of the

unit.

VCAUTION

Before turning the unit on, lower the volumes of connected

equipment to their minimum levels.

Failure to do so might cause sudden loud noises, which could

harm your hearing or result in other trouble.

h Analog output connectors

These are balanced Euroblock analog output connectors.

(HOT, COLD, GND from the left)

Mono signals will be output if MONO - STEREO (j) switches

are set to MONO.

j MONO - STEREO switches

Set whether the signals output from the analog output jacks

(h) are stereo or mono.

Set it to STEREO for stereo output or MONO for mono output.

During mono output, the same signal is output on both left

and right channels. Stereo input sources will be mixed to

mono signals and output.

Output channels that are set to MONO will be mono when

monitored with headphones.

These are set to MONO when shipped new from the factory.

k Line input GAIN knobs

Use to adjust the levels of the line input jacks (l).

NOTE

Use a small flathead screwdriver to adjust these.

l Line input jacks

These RCA pin jacks are analog line inputs.

Use RCA cables to connect CD players and similar devices to

these jacks.

; TALKOVER THRESHOLD knob

Set the input sensitivity (threshold level) for the talkover

function. (See “Using the talkover function” on page 16)

NOTE

This cannot be set separately for mic input channels 1-2.

z TALKOVER TIME knob

Use this to set the time until the talkover function deactivates

(release time). (See “Using the talkover function” on page

16)

NOTE

This cannot be set separately for mic input channels 1-2.

x Mic input EQ knobs

This is a 3-band equalizer (HIGH/MID/LOW) for the mic input

sound.

Setting range: ±15 dB

NOTE

Use a small flathead screwdriver to adjust these.

c Mic input GAIN knobs

Use to adjust the input levels of the mic input connectors (b,

Euroblock).

NOTE

Use a small flathead screwdriver to adjust these.

v Mic input connector PHANTOM switches

Use these switches to supply +48V phantom power to the

mic input connectors (b, Euroblock).

The PHANTOM switches for the mic input connectors provide

+48V phantom power. (See “Connecting microphones” on

page 14)

These are set to OFF when shipped new from the factory.

b Mic input connectors

These are balanced Euroblock mic input connectors. (HOT,

COLD, GND from the left)

Use the mic input GAIN knobs (c) to set the input levels.

To send mic input from the mic input connectors (b) to

mic input channel 1, set the front mic input channel 1 input

source switch (8) to REAR.

n PAD switches

Use to switch the input levels of the mic input jacks (b,

Euroblock). (24dB attenuation)

Set to ON if a connected mic input level is high.

This can be set for each input channel independently.

These are set to OFF when shipped new from the factory.

m HPF switches

Setting these switches to ON enables high pass filters that

cut noise and other sounds at low frequencies.

These are set to OFF when shipped new from the factory.

NOTE

When the MIC1 HPF switch is turned ON/OFF, the high pass

filter affects not only the rear mic input connectors (b,

Euroblock) but also the front INPUT jack (1).

, TALKOVER switches

These turn the talkover function on/off. (See “Using the

talkover function” on page 16)

These are set to OFF when shipped new from the factory.

NOTE

When the MIC1 TALKOVER switch is turned ON/OFF,

the talkover function affects not only the rear mic input

connectors (b, Euroblock) but also the front INPUT jack (1).

12 TASCAM MZ-123BT

Preparation

Connecting Euroblock plugs

Euroblock plug

Euroblock plug tab

Flat-blade screwdriver

Terminal screw

2.5 mm or less

1. Loosen the Euroblock plug terminal screws.

NOTE

Use a flat-blade screwdriver with a width of 2.5mm or less.

2. Insert wires.

NOTE

AWG16-AWG28 wires are compatible with the included

Euroblock plugs. Using wires within the compatible range,

trim about 7 mm of the protective sheaths from their ends.

3. Tighten the Euroblock plug terminal screws.

NOTE

Confirm that the wires cannot be pulled out.

4. Use an included wire band to attach the wires to the

Euroblock plug tab.

Attaching the Bluetooth antenna

Before connecting to a Bluetooth device, follow these

procedures to attach the included Bluetooth antenna.

NOTE

When this unit is shipped new, a cap is attached to the

Bluetooth antenna connector. Remove the cap before

attaching the Bluetooth antenna.

Nut

Bluetooth antenna connector

Bluetooth antenna

1. Attach the included Bluetooth antenna to the Bluetooth

antenna connector.

2. Turn the Bluetooth antenna nut to secure it to the antenna

connector.

3. Raise the Bluetooth antenna.

ATTENTION

iUse the included antenna, which was designed for use with

the MZ-123BT.

iBe careful to bend the antenna in the correct direction.

iDo not forcefully bend the antenna.

TASCAM MZ-123BT 13

Connecting other equipment

This is an example of MZ-123BT connections.

Precautions before making connections

pCarefully read the operation manuals of the devices to be connected and then connect them correctly.

pBefore making connections, turn this unit and all equipment to be connected off (standby).

pInstall all connected devices, including this unit, so that they are powered from the same line. When using a power strip or similar

device, be sure to use one that has high current capacity (thick cable) in order to minimize fluctuations in power voltage.

pBefore connecting audio equipment, set the following knobs to their lowest values.

Failure to do so could cause sudden loud noises from monitoring equipment, and this could damage the equipment or harm hearing.

oINPUT GAIN knob (2)

oMic input VOLUME knobs (w)

oLine input VOLUME knobs (t)

oLine output VOLUME knobs (p)

oPHONES VOLUME knob (s)

oLine input GAIN knobs (k)

oMic input GAIN knobs (c)

pSet the front and rear PHANTOM switches to OFF.

Headphones

Amplifier and speakers (zone 1)

Mic

CD player

Portable audio player

Amplifier and speakers (zone 2)Amplifier and speakers (zone 3)

Examples of connections to an MZ-123BT

14 TASCAM MZ-123BT

Connecting microphones

Dynamic mics

Connect these to the front INPUT jack (1) or the rear mic

input connectors (b).

Condenser mics

When using a condenser mic that requires phantom power,

connect it to the front INPUT jack (1) or the rear mic input

connectors (b).

When connecting one to the front INPUT jack (1), set the

INPUT jack PHANTOM switch (9) to +48V.

When connecting one to a rear mic input connector (b), set

that mic input connector PHANTOM switch (v) to +48V.

VCAUTION

Set the following knobs to their minimum values before

changing an INPUT jack PHANTOM switch (9) or mic input

connector PHANTOM switch (v) setting.

Depending on the connected mics, sudden loud noises from

monitoring equipment could occur, and this could damage

the equipment or harm hearing.

oINPUT GAIN knob (2)

oMic input GAIN knobs (c)

oMic input VOLUME knobs (w)

oLine output VOLUME knobs (p)

oPHONES VOLUME knob (s)

ATTENTION

iBefore connecting condenser mics, turn this unit and all

equipment to be connected off (standby).

iPHANTOM switches can be set for each channel separately.

Do not set a switch to +48V when connecting a mic that does

not require phantom power.

iDo not connect or disconnect mics when a PHANTOM

switch is +48V. Doing so could cause a loud noise and might

damage this unit and connected equipment.

iSet a PHANTOM switch to +48V only when using a condenser

mic that requires phantom power. Setting a PHANTOM

switch to +48V when a dynamic mic or other mic that does

not require it is connected could damage this unit and

connected equipment.

iSupplying phantom power to some ribbon mics could break

them. If unsure, check the specifications of the ribbon mic.

NOTE

If not using the INPUT jack (1) for a long time, attach the

included XLR cover to it.

Connecting electronic devices and other

audio equipment

Connect electronic devices, audio devices and other equipment

to the rear line input connectors (l) or the front AUX IN jack

(y).

When connecting to the AUX IN jack, set the AUX IN - Bluetooth

switch (u) to AUX IN.

Connecting headphones

Connect headphones to the PHONES (d) jack (standard stereo).

Sound can be monitored before output through the analog

output connectors (h).

Use the monitoring switches (5) to select the outputs that you

want to monitor.

VCAUTION

Before connecting headphones, minimize the volume with

the PHONES VOLUME (s) knob. Failure to do so might cause

sudden loud noises, which could harm your hearing or result

in other trouble.

Connecting stereo amplifiers

When connecting stereo amplifiers, connect them to the analog

output connectors (h).

The outputs of the connectors are independent and have their

own dedicated line output VOLUME knobs (p), so you can set

their output levels separately.

Connecting with Bluetooth devices

This unit can input sound from a computer, portable audio

device or other equipment that supports Bluetooth (A2DP).

To input audio from Bluetooth, set the AUX IN - Bluetooth switch

(u) to Bluetooth.

Pairing

Follow the procedures below to enable communication with a

Bluetooth device.

NOTE

Pairing also requires operation of the Bluetooth device.

Refer to the operation manual of the Bluetooth device for

procedures.

1. Set the AUX IN - Bluetooth switch (u) to Bluetooth.

2. Press and hold the PAIRING (a) button for at least 3

seconds.

The PAIRING indicator blinks.

3. Select “MZ-123BT” (this unit) on the other Bluetooth device.

When pairing succeeds, the PAIRING indicator will stop

blinking and remain lit, and connection with the other

device will be complete.

NOTE

iSome older Bluetooth devices require the input of a passkey.

Enter “0000” in such cases.

iPairing will automatically end if connection is not confirmed

within two minutes.

iThis unit will automatically try to connect with the Bluetooth

device to which it was previously connected if the AUX IN -

Bluetooth switch (u) is set to Bluetooth when the unit is on

or if it is turned on when the switch is set to Bluetooth. At

this time, pairing will automatically end after five minutes if

connection is not possible because that Bluetooth device is

not turned on or its Bluetooth function is turned off.

TASCAM MZ-123BT 15

Unpairing

The Bluetooth device that is currently connected can be

unpaired from the unit.

1. Press and hold the PAIRING (a) button for at least 3

seconds.

2. This ends the pairing with the device. The PAIRING (a)

indicator will start blinking and the unit will be ready to

pair.

Turning the power on and off

VCAUTION

iTurn down the volume of the sound system connected to

the unit before starting up or shutting down the unit. Loud

noises could damage the speakers or harm your hearing.

iDo not wear connected headphones when turning the unit

on and off. Loud noises could damage the headphones and

harm your hearing.

Before turning the power on

1. Make the following settings on the front and rear of the

unit.

oFront panel knobs w MIN

oRear GAIN knobs w MIN

oRear TALKOVER knobs w center values

oRear EQ knobs w center values

oOUTPUT SELECT switches w off (not pushed in)

oMonitoring switches w off (not pushed in)

oPHANTOM switches w OFF

2. Minimize the output levels of audio sources and input levels

of amplifiers connected to this unit.

Turning the power on

1. Turn connected input audio source devices on.

2. Use the POWER (g) switch on the back of the unit to turn

its power on.

The POWER (7) indicator on the front of the unit will light

when on.

3. Finally turn amplifiers on.

Turning the power off

Follow the procedures above in reverse when turning the power

off.

Failure to follow the correct order could result in clicking noises,

for example, that might damage equipment.

Operation procedures

After turning the power on, adjust the levels of the input signals.

Adjusting line input channels 1-2

1. Set the line input GAIN knobs (k) and the line input

VOLUME knobs (t) to their center values.

2. Press the line input OUTPUT SELECT switches (4) to select

whether their input signals are sent to those stereo buses.

3. Adjust the line output VOLUME knobs (p) to low volumes.

4. Start playback on the connected audio device.

Use the rear input GAIN knobs (k) to adjust the input levels

so that the line input PEAK indicators (e) do not light.

5. Follow the above procedures to adjust other input channels

with connected audio devices.

NOTE

The level sent from the line input channel 3 AUX IN jack (y)

or Bluetooth device cannot be adjusted.

Adjusting the input of a mic connected to

a mic input connector (rear panel)

1. Set the mic input channel 1 input source switch (8) to

REAR.

2. Set the mic input GAIN (c), EQ (x) and VOLUME (w) knobs

to their center values.

3. Press the mic input OUTPUT SELECT switches (3) to select

which stereo buses their input sounds are sent to.

4. Adjust the line output VOLUME knobs (p) to low volumes.

5. Try speaking into the mic.

Use the mic input GAIN knobs (c) to adjust the input levels

so that the mic input PEAK indicators (0) do not light.

6. Use the mic input EQ knobs (x) to adjust the 3-band

(HIGH/MID/LOW) equalizers.

NOTE

iIf a connected mic input level is high, set its PAD switch (n)

to ON.

iThe HPF switch (m) can be set to ON as necessary to enable

the high-pass filter, which will cut low-frequency noise and

other sounds.

Adjusting input from the mic connected

to the front INPUT jack

1. Set the mic input channel 1 input source switch (8) to

FRONT HIGH.

2. Set the INPUT GAIN (2), mic input EQ (x) and mic input

VOLUME (w) knobs to their center values.

NOTE

iThe front INPUT jack (1) and the rear MIC 1 input connectors

(b) cannot be used at the same time.

iIf the input level from the connected mic is high, set the mic

input channel 1 input source switch (8) to FRONT LOW.

16 TASCAM MZ-123BT

Output channels

Output signals are sent to the analog output connectors (h)

from the stereo bus.

Adjusting analog outputs

Use the line output VOLUME knobs (p) to adjust the output

levels so that the analog output PEAK indicators (i) do not

light.

NOTE

Mono signals will be output if MONO - STEREO (j) switches

are set to MONO.

Using the talkover function

The signal levels from the stereo bus can be automatically

attenuated when the sound levels of connected mics exceed the

level set by the TALKOVER THRESHOLD knob (;), making the

sound from the mics easier to hear.

This only attenuates the levels of output channels to which that

mic is assigned.

Examples

If MIC 2 OUTPUT SELECT switch 3 (3) is on while switch 1

and 2 are off, when MIC 2 exceeds the set level, the other

inputs to output channel 3 will be automatically attenuated

before the sound of MIC 2 is mixed in and output. Output

channels 1 and 2 will not be attenuated and the sound of MIC

2 will not be mixed into them.

1. Enable the talkover function for the desired mic input

channels by setting their TALKOVER switches (,) to ON.

2. Select the output channels that will be affected by the

talkover function by setting the mic input OUTPUT SELECT

switches (3).

3. Use the TALKOVER THRESHOLD knob (;) to set the input

sensitivity (threshold level) for the talkover function.

4. Use the TALKOVER TIME knob (z) to set the time until the

talkover function deactivates (release time).

Monitoring

Stereo headphones can be used to monitor the signals from the

output channels of this unit.

Turn on the monitoring switches on for output channels 1–3

(5) to enable monitoring of the signals output from the analog

output connectors (h).

1. When the monitoring switches (5) for the output channels

to be monitored are pressed, their switch indicators (5) will

light.

2. Use the PHONES VOLUME (s) knob to adjust the

monitoring output level.

NOTE

iWhen multiple monitoring switches (5) are on, a mix of

those signals can be monitored.

iSignals after the levels have been adjusted using the line

output VOLUME knobs (p) will be output.

iMono signals will be output for output channels that have

their MONO - STEREO (j) switches set to MONO.

Troubleshooting

If you are having trouble with the operation of this unit, please

try the following before seeking repair.

If these measures do not solve the problem, please contact

the store where you purchased this unit or TASCAM customer

support service.

The unit will not turn on.

pConfirm that the power plug and other connectors are

inserted completely.

Sound is not output from speakers

connected to the analog output jacks.

pCheck the settings and volume of the connected amplifier.

pAre the line output VOLUME knobs (p) turned up?

pConfirm that the input sound source is connected properly.

The volume is low even when VOLUME knobs

are turned up.

pAre the line input GAIN (k) knobs set properly?

pAre the INPUT GAIN knobs (2) and mic input GAIN knobs

(c) set properly?

pIs the output volume of the audio device connected to the

AUX IN jack (y) raised?

pIs the output volume of the paired Bluetooth device raised?

The sound is distorted.

pAre the input channel GAIN knobs set too high?

Are the input source levels to high?

pAre the mic input GAIN knobs (c) set too high?

pAre the line output VOLUME knobs (p) set too high?

pIs the monitoring level too high, causing the monitoring

system to distort?

pIs the output volume of the audio device connected to the

AUX IN jack (y) set too high?

pIs the output volume of the paired Bluetooth device set too

high?

No sound is output from headphones.

pUse the monitoring switches (5) to select the outputs to

monitor.

TASCAM MZ-123BT 17

Sound via Bluetooth breaks up or is noisy.

pAre there any wireless LAN devices, other Bluetooth devices,

microwave ovens or similar equipment nearby?

Keep such devices as far away as possible during use.

pTry reducing the distance between this unit and the other

Bluetooth device. Try changing the positions of this unit and

the other Bluetooth device.

pThe operation of apps other than for music playback on the

smartphone could cause the sound to break up. In this case,

stop operation of apps other than the one used for music

playback.

Cannot connect or communication is

interrupted when using Bluetooth.

pConfirm that the other Bluetooth device power is on and that

its Bluetooth function is on.

pConfirm that the other Bluetooth device is not too far away.

Are there walls or other obstacles, for example, between this

unit and the other Bluetooth device?

Try changing the positions of this unit and the other

Bluetooth device.

pTurn OFF and restart the MZ-123BT.

pRemove the “MZ-123BT” pairing record from the other

Bluetooth device, and try pairing the unit with that Bluetooth

device again. (See “Connecting with Bluetooth devices” on

page 14)

Cannot pair with another Bluetooth device.

pConfirm that the other Bluetooth device supports A2DP.

pConfirm that the other Bluetooth device is in a state that

allows transmission. For details, check the operation manual

of that Bluetooth device.

pTurn the power off for both this unit and the other Bluetooth

device once, turn them both on again and try pairing them.

pTurn off Bluetooth devices other than the one that you are

trying to pair with.

pRemove the “MZ-123BT” pairing record from the other

Bluetooth device, and try pairing the unit with that Bluetooth

device again. (See “Connecting with Bluetooth devices” on

page 14)

Specifications

Audio inputs

MIC INPUT (BALANCED) jack (front)

Connector:

XLR-3-31 equivalent

(1: GND, 2: HOT, 3: COLD)

6.3mm (1/4”) standard TRS jack

(Tip: HOT, Ring: COLD, Sleeve: GND)

Rated input level:

-26 dBu (0.039 Vrms, when FRONT HIGH)

-2 dBu (0.616 Vrms, when FRONT LOW)

Maximum input level:

-10 dBu (0.245 Vrms, when FRONT HIGH)

+14 dBu (3.884 Vrms, when FRONT LOW)

Minimum input level:

-65 dBu (0.0004 Vrms, when FRONT HIGH)

-41 dBu (0.007 Vrms, when FRONT LOW)

Gain adjustment range: 39 dB

Input impedance: 2.2 kΩ

MIC IN 1-2 (BALANCED) connectors (rear)

Connectors: Euroblock (balanced) 3.81mm pitch

Rated input level:

-26 dBu (0.039 Vrms, when PAD switch OFF)

-2 dBu (0.616 Vrms, when PAD switch ON)

Maximum input level:

-10 dBu (0.245 Vrms, when PAD switch OFF)

+14 dBu (3.884 Vrms, when PAD switch ON)

Minimum input level:

-65 dBu (0.0004 Vrms, when PAD switch OFF)

-41 dBu (0.007 Vrms, when PAD switch ON)

Gain adjustment range: 39 dB

Input impedance: 2.2 kΩ

LINE INPUTS 1-2 (UNBALANCED) connectors

(rear)

Connectors: RCA pin jacks

Nominal input level: -10 dBV (0.316 Vrms)

Maximum input level: +6 dBV (2.0 Vrms)

Gain adjustment range: ±16 dB

Input impedance: 10 kΩ or higher

AUX IN (UNBALANCED) jack (front)

Connector: 3.5mm (1/8”) stereo mini jack

Nominal input level: -20 dBV (0.1 Vrms)

Maximum input level: -4 dBV (0.63 Vrms)

Input impedance: 10 kΩ or higher

Audio outputs

OUTPUTS (BALANCED) connectors

Connectors: Euroblock (balanced) 3.81mm pitch

Rated output level:

+4 dBu (1.228 Vrms, when VOLUME knob at 0 dB)

Maximum output level:

+24 dBu (12.282 Vrms)

Output impedance: 200Ω

PHONES jack

Connector: 6.3mm (1/4”) standard stereo jack

Maximum output: 80 mW + 80 mW or higher

(THD+N 0.1% or less, into 32Ω load)

18 TASCAM MZ-123BT

Audio performance

Frequency response

MIC INPUT w LINE OUTPUT

20 Hz - 20 kHz: +0.5 dB/-1.0 dB