Gigabyte R18N-F2A インストールガイド

Motherboard Components

1 2 3 4 5 6

11 10

15 16

53 54

55 56

5758

65 66

43 30

System Components

456

No Descripon

1 HDD bays

2 System fan #13 (FAN13)

3 System fan #11/#12 (FAN11/FAN12)

4 System fan #9/#10 (FAN9/FAN10)

5 System fan #7 (FAN7)

6 System fan #5 (FAN5)

7 System fan #3/#4 (FAN3/FAN4)

8 System fan #1/#2 (FAN1/FAN2)

9 System fan #15 (FAN15)

No Descripon

1 HDD#0

2 HDD#1

3 HDD#2

4 HDD#3

5 HDD#4

6 HDD#5

7 HDD#6

8 HDD#7

9 HDD#8

10 HDD#9

HDD Backplane Board Components

CAUTION!

To connect system fan connector, follow the instrucon:

 Blue/Red cable connect to odd numbered connector.

 White/Amber cable connect to even numbered connector.

No Descripon

10 Memory slots

11 CPU heat sink

12 PCIe riser bracket

13 Power supply cage

CAUTION!

Before you remove or install the system

cover:

Make sure the system is not turned on

or connected to AC power.

No Descripon

11 SGPIO Port B

12 SGPIO Port A

13 Fan connector#16

14 Fan connector#15

15 Fan connector#2

16 Fan connector#1

17 Fan connector#4

18 Fan connector#3

19 Fan connector#6

20 Fan connector#5

No Descripon

21 Fan connector#8

22 Fan connector#7

23 Fan connector#10

24 Fan connector#9

25 Fan connector#12

26 Fan connector#11

27 Fan connector#14

28 Fan connector#13

29 JP_SEL1

30 JP_SEL2

31 JP_SEL3

HDD Back Plane Board CPLD Configuration

JP_SEL1 2-3 Close

2-3 Close

1-2 Close

JP_SEL2Jumper

SGPIO Decode Mode

SGPIO Port Port A Port B N/A Port B N/APort A

SATA/SAS#0~#3

HDD#0~#3 HDD#0~#3HDD#4~#7 HDD#8~#9 HDD#8~#9HDD#4~#7

SATA/SAS#0~#3 SATA/SAS#0~#3SATA/SAS#2~#5

SATA/SAS#0~#3

NVMe#0~#1

SATA/SAS#0~#1

NVMe#0~#1

Host Interface

HDD Configuration

Normal Mode Shift Mode

JP_SEL3

注意！

在卸下或安装系统机盖之前，请注意

下列事项：

确保系统未开启且未连接到交流电源。

注意！

 蓝/红电缆连连接于单数风扇插座。

 白/橘电缆连连接于双数风扇插座。

Front Panel Header

No. Pin Deﬁne

1 Power LED+

3 No Pin

5 Power LED-

7 HDD LED+

9 HDD LED-

11 Power Buon

13 GND

15 Reset Buon+

17 GND

19 ID Switch+

21 ID Switch-

23 NMI Switch-

No. Pin Deﬁne

2 5V Standby

4 ID LED+

6 ID LED-

8 System Front Board LED+

10 System Status LED-

12 LAN1 Acve LED+

14 LAN1 Link LED-

16 SMBus Data

18 SMBus Clock

20 Case Open

22 LAN2 Acve LED

24 LAN2 Link LED-

24 23

HDD Back Plane Board Header

1 2

25 26

No. Pin Deﬁne

1 BP_SGP_CLK

3 BP_SGP_GLD

5 BP_SGP_DOUT

7 Key Pin

9 GND

11 BP_LED_G_N

13 BP_SGP_DIN

15 GND

17 GND

19 P_3V3_AUX

21 P_3V3_AUX

23 GND

25 BP_PRESENSE

No. Pin Deﬁne

2 No Connect

4 FAN_SGP_GLD

6 GND

8 Reset

10 BP_LED_A_N

12 GND

14 No Connect

16 SMB_BP_DATA

18 SMB_BP_CLK

20 BMC_ACK

22 BMC_REQ

24 Key Pin

26 GND

System Cover

Hard Disk Drive and Back Plane Board

Fan Duct

Installing CPU

Heat Sink

Type

Ranks Per

DIMM and

Data Width

Speed (MT/s);

Slot Per Channel (SPC) and DIMM Per Channel (DPC)

RDIMM

LRDIMM

SRx4 2133

2133

1866

2133

1 Slot Per Channel

1DPC

2 Slot Per Channel

1DPC 2DPC

SRx8

DRx8

DRx4

QRx4

 When only one DIMM is used, it must be populated in memory slot0 ﬁrst.

 Memory populated sequence must be followed with slot0/slot1/slot2

 System will not boot normally with incorrect populated sequence.

 只使用一个DIMM时，必须安装到内存插槽0。

 内存安装顺序必须是插槽0/插槽1/插槽2。

 若安装顺序有误，系统将不能正常引导。

System Front View System Rear View

Memory Populaon Conﬁguraon

1 12 2 3

4 5 8

6 7

CAUTION!

Before you remove or install the system fan:

 Make sure the system is not turned on or connected to the AC power.

 Disconnect all necessary cable connecons. Failure to observe these

warnings could result in personal injury or damage to the equipment.

System Fan

注意！

确保系统未开机且未连接到交流电源。

断开所有必要的线缆连接。若不遵循这些警告，可能造成人员

伤害或设备损坏。

11 12

13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28

No Descripon

1 HDD bay#0

2 HDD bay#1

3 HDD bay#2

4 HDD bay#3

5 HDD bay#4

6 HDD bay#5

7 HDD bay#6

8 HDD bay#7

9 HDD bay#8 (Support NVMe)

10 HDD bay#9 (Support NVMe)

11 Front panle LEDs and buons

12 USB 3.0 ports

No Descripon

1 Power supply fan

2 Power supply module cord socket

3 VGA port

4 RJ-45 LAN ports

5 ID switch buon w/LED

6 RJ-45 COM port

7 10/100/1000 Server management LAN port

8 USB 2.0 ports

9 USB 3.0 ports

10 Low-proﬂe riser card bay

Front & Rear

Off

State Description

Yellow On 1Gbps data arte

Green On 100Mbps data arte

10Mbps data arte

Speed LED Link/Acvity

LED

PCI Express Card

注意！

在替换或安装电源前，请注意下列事项：

确保系统未开启且未连接到交流电源。

CAUTION!

Before you remove or install the power supplies:

Make sure the system is not turned on or connected to

AC power.

Power Supply Front Panel LED and Buons

编号名称颜色状态

R18N-F2A Quick Installaon Guide

No. Code Descripon

1 USB3_MLAN BMC Management LAN port (top) / USB 3.0 ports (boom)

2 COM1_USB2 RJ45 COM port (top) / USB 2.0 ports (boom)

3 SW_ID ID switch buon w/LED

4 LAN1 LAN port #1

5 LAN2 LAN port #2

6 VGA VGA port

7 RISER_SLOT3 PCI Express x16 slot

8 RISER_SLOT2 PCI Express x16 slot

9 PCIE_4 PCI Express x16 slot (mezzanine type)

10 BAT Baery socket

11 S3_MASK S3 Power On Select jumper

1-2 Close: Stop an inial power on when BMC is not ready.

2-3 Close: Keep inial power on. (Default seng)

12 CASE_OPEN Case open intrusion alert header

13 SW_RAID Intel/LSI Soware RAID Key jumper

14 CLR_CMOS Clear CMOS jumper

1-2 Close: Normal operaon (Default seng)

2-3 Close: Clear CMOS data.

15 PSU2 Hot-plug PSU module connector#2

16 PSU1 Hot-plug PSU module connector#1

17 ATX1 14 pin main power connector

18 12V_GPU3_2 4 pin 12V power connector

19 12V_GPU3_1 8 pin power connector

20 12V_GPU2_2 4 pin 12V power connector

21 12V_GPU2_1 8 pin power connector

22 12V_GPU1_2 4 pin 12V power connector

23 12V_GPU1_1 8 pin power connector

24 DIMM_P1_E0 Channel 1 slot 0 (for secondary CPU)

25 DIMM_P1_E1 Channel 1 slot 1 (for secondary CPU)

26 DIMM_P1_E2 Channel 1 slot 2 (for secondary CPU)

27 DIMM_P1_F0 Channel 2 slot 0 (for secondary CPU)

28 DIMM_P1_F1 Channel 2 slot 1 (for secondary CPU)

29 DIMM_P1_F2 Channel 2 slot 2 (for secondary CPU)

30 CPU1 Intel LGA2011 Socket R3 (Secondary CPU)

31 DIMM_P1_H2 Channel 3 slot 2 (for secondary CPU)

32 DIMM_P1_H1 Channel 3 slot 1 (for secondary CPU)

33 DIMM_P1_H0 Channel 3 slot 0 (for secondary CPU)

34 DIMM_P1_G2 Channel 4 slot 2 (for secondary CPU)

35 DIMM_P1_G1 Channel 4 slot 1 (for secondary CPU)

36 DIMM_P1_G0 Channel 4 slot 0 (for secondary CPU)

No. Code Descripon

37 DIMM_P0_A0 Channel 4 slot 0 (for primary CPU)

38 DIMM_P0_A1 Channel 1 slot 1 (for primary CPU)

39 DIMM_P0_A2 Channel 1 slot 2 (for primary CPU)

40 DIMM_P0_B0 Channel 2 slot 0 (for primary CPU)

41 DIMM_P0_B1 Channel 2 slot 1 (for primary CPU)

42 DIMM_P0_B2 Channel 2 slot 2 (for primary CPU)

43 CPU0 Intel LGA2011 Socket R3 (Primary CPU)

44 DIMM_P0_D2 Channel 4 slot 2 (for primary CPU)

45 DIMM_P0_D1 Channel 4 slot 1 (for primary CPU)

46 DIMM_P0_D0 Channel 4 slot 0 (for primary CPU)

47 DIMM_P0_C2 Channel 3 slot 2 (for primary CPU)

48 DIMM_P0_C1 Channel 3 slot 1 (for primary CPU)

49 DIMM_P0_C0 Channel 3 slot 0 (for primary CPU)

50 FP_1 Front panel header

51 BP_1 HDD back plane board header

52 IPMB IPMB connector

53 F_USB3 USB 3.0 header

54 BUZZER1 Buzzer

55 PCH_ME ME recovery jumper

1-2 Close: Normal operaon. (Default seng)

2-3 Close: ME recovery mode.

56 ME_UPDATE ME update jumper

1-2 Close: Normal operaon (Default seng)

2-3 Close: ME update mode.

57 MINI_CN1 Mini-SAS cable connector#1 supports SATA3 6Gb/s

58 MINI_CN2 Mini-SAS cable connector#2 supports SATA3 6Gb/s

59 SATA5 SATA3 6Gb/s connector

60 SATA4 SATA3 6Gb/s connector

61 BIOS_PWD Clearing Supervisor Password jumper

1-2 Close: Normal operaon. (Default seng)

2-3 Close: Skip supervisor password.

62 BIOS_RCVR BIOS recovery jumper

1-2 Close: Normal operaon. (Default seng)

2-3 Close: BIOS recovery mode.

63 RISER_1_2 PCI Express x16 slot (extension slot)

64 LED_BMC BMC frmware readiness LED

65 RISER_1_1 PCI Express x4 slot (extension slot)

66 BMC_FRB Force to Stop FRB Timer jumper

1-2 Close: Normal operaon. (Default seng)

2-3 Close: Force to Stop FRB Timer.

67 TPM TPM module connector

10/100/1000 LAN LED:

No. Name Color Status Description

5/6

Reset Button Press the button to reset the system.

Press the button to activate system identifcation.

System is powered on.

System is in ACPI S1 state (sleep mode).

HDD locate

HDD access

HDD fault

No HDD access or no HDD fault.

Link between system and network or no access.

Data transmission or receiving is occurring.

No data transmission or receiving is occurring.

System is not powered on or in ACPI S5 state (power off).

System is in ACPI S4 state (hibernate mode).

ID Button

Power LED Green

Green

Amber

Green/Amber

Solid On

Off

Blink

N/A

Green

N/A

HDD Status LED

LAN1/2 Active/Link LEDs

5/6

说明

复位按钮按此按钮启动系统。

按下按钮启动系统识别功能。ID按钮

系统处于开机状态。

系统处于ACPI S1状态（睡眠模式）。。

系统未开机或处于ACPIS5状态（关机状态）。

系统处于ACPI S4状态（休眠模式）。

电源按钮和LED 绿色

绿色

恒亮

不亮

闪烁

恒亮

不亮

闪烁

无亮灯

硬盘驱动器定位

硬盘驱动器访问

硬盘故障

无硬盘驱动器访问

系统和网络之间的链接

网络访问

断开连接/待机

绿色

橙色

绿色/橙色

不亮

亮

闪烁

无亮灯

硬盘驱动器LED

LAN1/LAN2活动LED

闪烁

P/N:

Regulatory Noces Connect With Us

WEEE Symbol Statement For more informaon, visit our website at:

hp://b2b.gigabyte.com

You are a professional?

Get access to our complete source of sales & markeng materials at:

hp://reseller.b2b.gigabyte.com

Join our server forum to discuss our products and get technical assistance at:

hp://forum.b2b.gigabyte.com

hps://www.facebook.com/gigabyteserver

The symbol shown below is on the product or on its packaging, which indicates that this product must not be disposed of with other

waste. Instead, the device should be taken to the waste collecon centers for acvaon of the treatment, collecon, recycling and

disposal procedure. The separate collecon and recycling of your waste equipment at the me of disposal will help to conserve

natural resources and ensure that it is recycled in a manner that protects human health and the environment.

For more informaon about where you can drop oﬀ your waste equipment for recycling, please contact your local government

oﬃce, your household waste disposal service or where you purchased the product for details of environmentally safe recycling.

 When your electrical or electronic equipment is no longer useful to you, "take it back" to your local or regional waste

collecon administraon for recycling.

 If you need further assistance in recycling, reusing in your "end of life" product, you may contact us at the Customer Care

number listed in your product's user's manual and we will be glad to help you with your eﬀort.

GIGABYTE产品未故意添加和使用有害物质（Cd、Pb、Hg、Cr+6、PBDE和PBB）。所有部件和元件均经过严格挑选，符合RoHS要求。此

外，我们GIGABYTE一直致力于开发不使用国际上禁止的有毒化学品的产品。

GIGABYTE products have not intended to add and safe from hazardous substances (Cd, Pb, Hg, Cr+6, PBDE and PBB). The parts and components

have been carefully selected to meet RoHS requirement. Moreover, we at GIGABYTE are connuing our eﬀorts to develop products that do not use

internaonally banned toxic chemicals.

Restricon of Hazardous Substances (RoHS) Direcve Statement

限制使用有害物质 (RoHS) 指令声明

California Proposion 65 Warning

WARNING:

This product contains a chemicals , including lead, known to the State of California to cause cancer and birth defects or other reproducve harm.

For more informaon, please visit: hp://www.p65warnings.ca.gov/

Baery Warning:

Incorrectly installing a baery or using incompable baery may increase the risk of ifre explosion. Replace the baery only with

the same or equivalent type.

 Do not disassemble, crush, punchture baeries.

 Do not store or place your baery pack next to or in a heat source such as a ﬁre, heatgenerang appliance, can or exhaust

vent. Heang baery cells to temperatures above 65oC (149oF) can cause explosion or ﬁre.

 Do not aempt to open or service baeries. Do not dispose of baeries in a ﬁre or with household waste.

电池警告：

电池安装不当或使用不兼容的电池会增加火灾爆炸风险。更换电池时，只可使用相同或同等类型的电池。

 请勿拆解、挤压、刺破电池。

 请勿将电池存放或放置在热源中或旁边，如火源、产生热的设备、罐体或排气口。电池温度升至65oC (149oF)以上

可能导致爆炸或火灾。

 请勿尝试打开或维修电池。电池废弃时，请勿投入火中或者作为家庭废弃物进行处理。

依照中华人民共和国的有毒有害物质的限制要求(China RoHS)提供以下的表格：

中华人民共和国电子信息产品中有毒有害物质或元素的名称及含量标识格式

Gigabyte R18N-F2A インストールガイド

関連論文

その他の書類