Stanley STDR5510 ユーザーマニュアル

カテゴリー
パワーツール
タイプ
ユーザーマニュアル
3
7
STDR5510
D
B
A
C
7
6
8
5
9
3
1
2
4
E N G L I S H
3
SPECIFICATION
STDR5510-A9
POWER W 550
VOLTAGE V 220
FREQUENCY Hz 50
NO-LOAD SPEED
/min
0-2800
REVERSE YES
LOCK ON YES
MAX DRILLING CAPACITY
-STEEL mm 10
-WOOD mm 25
CHUCK CAPACITY mm 1.5-10
Intended use
Your Stanley rotary drill has been designed for drilling in
wood, metal and plastic. This tool is intended for consumer
use only.
GENERAL SAFETY RULES
@
Warning! Read safety warnings and all instruc-
tions. Failure to follow all instructions listed below
injury.
Save all warnings and instructions for future reference.
The term "power tool" in all of the warnings listed below
refers to your mains operated (corded) power tool or battery
operated (cordless) power tool.
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
b. Do not operate power tools in explosive
liquids, gases or dust. Power tools create sparks which
may ignite the dust or fumes.
c. Keep children and bystanders away while operating
a power tool. Distractions can cause you to lose
control.
2. Electrical safety
a. Power tool plugs must match the outlet. Never
ROTARY DRILL
STDR5510
Technical data
modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools.
electric shock.
b. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
c. Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
d. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk of
electric shock.
e. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of electric
shock.
f. If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
3. Personal safety
a. Stay alert, watch what you are doing and use
common sense when operating a power tool. Do not
use a power tool while you are tired or under the
A moment
of inattention while operating power tools may result in
serious personal injury.
b. Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal
injuries.
c. Prevent unintentional starting. Ensure the switch is
in the off-position before connecting to power
source and/or battery pack, picking up or carrying
the tool.
switch or energising power tools that have the switch on
invites accidents.
d. Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal
injury.
e. Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power tool
in unexpected situations.
ENGLISH
4
f. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
g. If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection
can reduce dust-related hazards.
4. Power tool use and care
a. Do not force the power tool. Use the correct power
tool for your application. The correct power tool will do
the job better and safer at the rate for which it was
designed.
b. Do not use the power tool if the switch does not turn
it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
c. Disconnect the plug from the power source and/or
the battery pack from the power tool before making
any adjustments, changing accessories, or storing
power tools. Such preventive safety measures reduce
the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained
users.
e. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tools
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous
situation.
5. Service
a. Have your power tool serviced by a qualied repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is
maintained.
ADDITIONAL POWER TOOL SAFETY WARNINGS
@
Warning! Additional safety warnings for drills
and impact drills
u Wear ear protectors when impact drilling. Exposure
to noise can cause hearing loss.
u Use auxiliary handle(s), if supplied with the tool.
Loss of control can cause personal injury.
u Hold power tool by insulated gripping surfaces when
performing an operation where the cutting acces-
sory may contact hidden wiring or its own cord.
Cutting accessory contacting a "live" wire may make
exposed metal parts of the power tool "live" and could
give the operator an electric shock.
u Use clamps or another practical way to secure and sup-
port the workpiece to a stable platform. Holding the work
by hand or against your body leaves it unstable and may
lead to loss of control.
u Before drilling into walls, oors or ceilings, check for the
location of wiring and pipes.
u Avoid touching the tip of a drill bit just after drilling, as it
may be hot.
u This tool is not intended for use by persons(including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concern-
ing use of the appliance by a person responsible for their
safety. Children should be supervised to ensure that they
do not play with the appliance.
u The intended use is described in this instruction manual.
The use of any accessory or attachment or performance
of any operation with this tool other than those recom-
mended in this instruction manual may present a risk of
personal injury and/or damage to property.
Electrical safety
This tool is double insulated; therefore no earth
wire is required. Always check that the power
supply corresponds to the voltage on the rating
plate.
Features
This tool includes some or all of the following features.
1. Variable speed switch
2. Lock-on button
3. Forward/reverse slider
4. Chuck
5. Sleeve
6. Bit Shaft
7. Chuck key
8. Hole
9. Speed dial
E N G L I S H
5
Assembly
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
u Open the chuck by turning the sleeve (5) counterclock-
wise.
u Insert the bit shaft (6) into the chuck.
u Insert the chuck key (7) into each hole (8) in the side of
the chuck and turn clockwise until tight.
u Open the chuck as far as possible.
u Remove the chuck retaining screw, located in the chuck,
by turning it clockwise using a screwdriver.
u Tighten an Allen key into the chuck and strike it with a
hammer as shown.
u Remove the Allen key.
u Remove the chuck by turning it counterclockwise.
u
with the chuck retaining screw.
Use
Warning! Let the tool work at its own pace. Do not overload.
Warning!
for the location of wiring and pipes.
For drilling and for tightening screws, use forward (clock-
wise) rotation. For loosening screws or removing a jammed
drill bit, use reverse (counterclockwise) rotation.
u To select forward rotation, push the forward/reverse
slider (3) to the left position.
u To select reverse rotation, push the forward/reverse
slider to the right.
Viewed when holding the drill in the operating position.
After any reversing operations, return slider (3) to
forward position.
Warning! Never change the direction of rotation while the
motor is running.
Switching on and off
u To switch the tool on, press the variable speed switch
(1). The tool speed depends on how far you press the
switch.
u For continuous operation, press the lock-on button (2)
and release the variable speed switch. This option is
available only at full speed.
u To switch the tool off, release the variable speed switch.
To switch the tool off when in continuous operation,
press the variable speed switch once more and release
it.
u Based on the different applications, turn around the
speed dial (9) to control the maximum speed.
@
Warning! To reduce the risk of serious personal
injury, ALWAYS use proper hand position as
@
Warning! To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
DRILLING IN METAL
Start drilling with slow speed and increase to full power while
metal chips indicates the proper drilling rate. Use a cutting
lubricant when drilling metals. The exceptions are cast iron
and brass which should be drilled dry.
NOTE: Large [5/16" (8 mm)] holes in steel can be made
easier if a pilot hole [5/32" (4 mm)] is drilled first.
DRILLING IN WOOD
Start drilling with slow speed and increase to full power while
made with the same twist drills used for metal. These bits
may overheat unless pulled out frequently to clear chips from
with a block of wood.
Accessories
The performance of your tool depends on the accessory
used.Stanley accessories are engineered to high quality
standards and designed to enhance the performance of your
tool. By using these accessories you willget the very best
from your tool.
Maintenance
Your tool has been designed to operate over a long period of
time with a minimum of maintenance. Continuous
satisfactory operation depends upon proper tool care and
regular cleaning.
Warning! Before performing any maintenance, switch off
and unplug the tool.
u Regularly clean the ventilation slots in your tool using a
soft brush or dry cloth.
u Regularly clean the motor housing using a damp cloth.
ENGLISH
6
Do not use any abrasive or solvent-based cleaner.
Protecting the environment
Separate collection. This product must not be
disposed of with normal household waste.
Should you nd one day that your Stanley product needs re-
placement, or if it is of no further use to you, do not dispose
of it with household waste. Make this product available for
separate collection.
Separate collection of used products and
packaging allows materials to be recycled and
used again. Re-use of recycled materials helps
prevent environmental pollution and reduces the
demand for raw materials.
Local regulations may provide for separate collection of
electrical products from the household, at municipal waste
sites or by the retailer when you purchase a new product
Remarks
u Stanley's policy is one of continuous improvement to our
products and as such, we reserve the right to modify product
specications without prior notice.
u Standard equipment and accessories may vary by country.
u Product specications may differ by country.
u Complete product range may not be available in all countries.
Contact your local Stanley dealers for range availability.
简体
7
设计用途
Stanley 电钻设计用于在木材、金属和塑料上钻
孔。本工具仅供专业人士使用。
电动工具通用安全警告
警告!阅读所有警告和所有说明。不遵照
以下警告和说明会导致电击、着火和/或
严重伤害。
保存所有警告和说明书以备查阅。
在所有下列的警告中术语“电动工具”指市电驱动
(有线)电动工具或电池驱动(无线)电动工具。
1. 工作场地的安全
a. 保持工作场地清洁和明混乱和黑暗的场地会
引发事故。
b. 不要在易爆环境,如有易燃液体、气体或粉
环境下操作电动工具。电动工具产生的火花会点
燃粉尘或气体。
c. 让儿童和旁观者离开后操作电动工具。注意力不
集中会使你失去对工具的控制。
2. 电气安全
a. 电动工具插头必须与插座相配。绝不能以任
式改装插头。需接地的电动工具不能使用任何转
换插头。
电钻
STDR5510
技术参数
未经改装的插头和相配的插座将减少电击危险。
b. 避免人体接触接地表面,如管道、散热片
箱。如果你身体接地会增加电击危
c. 不得将电动工具暴露在雨中或潮湿环境水进
入电动工具将增加电击危险。
d. 不得滥用电线。绝不能用电线搬运、拉动电动工
具或拔出其插头。使电线远离热源、油、锐边或
运动部 受损或缠绕的软线会增加电击危险。
e. 当在户外使用电动工具时,使用适合户外使
的外接软线。适合户外使用的软线将减少
危险。
f. 如果在潮湿环境下操作电动工具是不可避免的,
应使用剩余电流动作保护器(RCD)。使用
RCD可减小电击危险。
3. 人身安全
a. 保持警觉,当操作电动工具时关注所从事的操作
并保持清醒。当你感到疲倦,或在有药物、酒精
或治疗反应时,不要操作电动工具。在操作电动
工具时瞬间的疏忽会导致严重人身伤害。
b. 使用个人防护装置。始终佩戴护目 全装
置,诸如适当条件下使用防尘面具、防滑安全
鞋、安全帽、听力防护等装置能减少人身伤害。
c. 防止意外启动。确保开关在连接电源和/或电池
组、拿起或搬运工具时处于关断位置。手指放在
已接通电源的开关上或开关处于接通时插入插头
可能会导致危险。
d. 在电动工具接通之前,拿掉所有调节钥匙或扳
手。遗留在电动工具旋转零件上的扳手或钥
导致人身伤害。
e. 手不要伸展得太长。时刻注意立足点和身体平
衡。这样在意外情况下能很好地控制电动工
f. 着装适当。不要穿宽
或佩戴饰品。让
、手套和头发远离运 部。 宽松衣服、佩
饰或长发可能会卷入运动部件中。
g.
如果提供了与排屑、集尘设备连接用的装置,要
确保他们连接完好且使用得当。使用这些装置可
减少尘屑引起的危险。
4.
电动工具使用和注意事项
a.
不要滥用电动工具,根据用途使用适当的电动工
具。选用适当设计的电动工具会使你工作
效、更安全。
b. 如果开关不能接通或关断工具电源,则不能使用
规格
STDR5510-A9
功率 550
电压 伏特 220
频率 赫兹 50
空载转速
转/分
0-2800
反转
锁定
最大钻孔能力
-钢材 毫米 10
-木材 毫米 25
夹头容量 毫米 1.5-10
简体
8
该电动工具。不能用开关来控制的电动工具是危
险的且必须进行修理。
c. 在进行任何调节、更 或贮存电动工具之
前,必须从电源上拔掉插头和/或使电池组与工
具脱开。这种防护性措施将减少工具意外启动的
危险。
d. 将闲置不用的电动工具贮存在儿童所及范围之
外,并且不要让不熟悉电动工具或对这些说明不
了解的人操作电动工具。电动工具在未经培训的
用户手中是危险的。
e. 保养电动工具。检查
是否调整到位
住,检查零破损情况和影响电动工具运
其他状况。如有损坏,电动工具应在使用前修理
好。许多事故由维护不良的电动工具引
f. 保持切削刀具锋利和清
保养良好的有锋利切
削刃的刀具不易卡住而且容易控制。
g. 按照使用说明书,考虑作业条和进行的作业
来使用电动工具、附和工具的刀头等。将电
动工具用于那些与其用途不符的操作可能会导
致危险。
5. 维修
a. 将你的电动工具送交专业维修人员,使用同
进行修理。这样将确保所维修的电动工具的
安全性。
电动工具附加安全警告
警告!电钻和冲击钻附加安全
使用冲击电钻时要戴好耳罩。暴露在噪声中会引
起听力损伤。
使用随工具提供的辅助手柄。操作失手会引起
人身伤害。
当在钻削附 可能触及暗线或其自身软线之处进
行操作时,要通过绝缘握持面来握持工具。钻
削附件碰到带电导线会使工具外露的金属零件
带电从而使操作者受到电击。
使用夹具或采取其他可行的方法,将工件固
定、支撑到稳定的平台上。手持或用身体顶住
工件都是不稳定的,会导致操作失控。
在墙上、地板或天花板上钻孔之前,请检查电
线和管道位置
不要在钻孔后立刻碰触可能还发热的钻头尖端。
本工具不适合体力、感觉或智力不足,或者缺
乏经验及知识的人员(包括儿童)使用,除非
负责他们安全的人员已经为他们提供关于使用
此设备的监督或指示。应看管好儿童,以确保
他们不将此设备当做玩具来玩。
本使用手册描述了工具的设计用途。使用非本
使用手册所建议的任何其他附件或配件,或者
使用本工具执行非手册建议的任何其他操作,
都可能存在人身伤害和/或财产损失的危险。
电气安全
本工具采用双重绝缘,因此无需接地线。
请务必检查电源电压是否与铭牌上的电压
一致。
部名称
本产品包含如下部分或全部部件。
1. 变速开关
2. 锁定按钮
3. 正/反转滑块
4. 夹头
5. 套管
6. 钻头轴
7. 夹头钥匙
8. 插孔
9. 速度旋钮
组装
警告! 组装前,请确保关闭工具电源并拔下工具
插头。
带栓夹头(图 B)
通过逆时针转动套管 (5) 打开夹头。
将钻头轴 (6) 插入夹头。
将夹头钥匙 (7) 插入夹头侧面的每个插孔 (8) 然
后顺时针转紧。
卸下及装回夹头(图 C)
将夹头打开到最大位置。
用螺丝起子顺时针转动夹头的固定螺钉将螺丝
取出。
将内六角起子转紧到夹头内,然后用锤子敲
打,如图所示。
取出内六角起子。
逆时针转动夹头将它取出。
要装回夹头,可将它旋入心轴,然后用夹头固
定螺钉将它锁紧。
9
使用
警告!请让工具在自有速度下工作。切勿过载。
警告!在墙上、地板或天花板上钻孔之前,请检查
电线和管道位置。
选择旋转方向(图 D)
如果要钻孔和转紧螺钉,使用向前(顺时针)旋
转。如果要转松螺钉或取出卡住的钻头,使用向后
(逆时针)旋转。
要选择向前旋转,将正/反转滑块 (3) 拨到左边
要选择向后旋转,请将正/反转滑块拨到右边。
以使用者手持操作电钻时的位置为查看位置。
反转操作完毕后,将滑块 (3) 拨回正转位置。
警告!在马达运行时切勿更改旋转方向。
启动与关闭
要开启工具电源,请按下变速开关 (1)。工具转
速取决于您按下开关的程度。
要使工具连续运转,请按下锁定按钮 (2),然后
松开变速开关。此选项只在全速运作时可用。
要关闭工具电源,请松开变速开关。要在连续
运转时关闭工具电源,请再次按下变速开关然
后松开。
根据不同的应用情况,转动速度旋钮 (9) 控制
最大速度。
正确的手持方式(图 E)
@
警告!为降低严重的人身伤害风险,请
务必使用正确的手持方式,如图 E
示。
@
警告!为降低严重的人身伤害风险,请
务必紧握工具以防止意外事件。
在金属材料上钻孔
开始钻孔时,采用较低速度;对工具施加稳固压
力时,请增至全功率。如果金属屑平滑、均匀地
流出,则表明钻孔速度适当。在金属材料上钻孔
时,请使用切削润滑剂。但铸铁和黄铜材料例外,
应干钻。
注:在钢材上钻大孔 [5/16 英寸(8 毫米)时,
如果首先钻先导孔 [5/32 英寸(4 毫米),则比较
容易进行。
在木材上钻孔
开始钻孔时,采用较低速度;对工具施加稳固压力
时,请增至全功率。木材钻孔可以使用和钢材钻孔
一样的麻花钻头。这些钻头会过热,除非你不断拔
出钻头来清理钻屑。易碎裂材料应垫上木块。
工具性能取决于所使用的附件。史丹利附件按照
高质量标准设计,旨在增强工具的性能。购买这些
附件会令您的工具如虎添翼。
维护
此工具设计精良,可以长期使用,仅需极少维护。
要持续 获得令人满意的工作效果,需要对工具进
行适当的保养和定期清洁。
警告!在进行任何维护前关闭电源并拔下插头。
定期使用软刷或干布清洁工具内的通风槽。
定期使用湿布清洁电动机外壳。请勿使用任何
研磨性或溶剂型清洁剂。
保护环境
分类回收。本产品不得与普通家庭垃圾一
起处理。
如果发现您的史丹利产品需要进行替换,或您已
经不再需要使用这些产品,请勿将它们与家庭废物
一起处理。请将它们 单独分类回收。
分类回收使用过的产品和包装能够让材料
得以再循环和再利用。再生材料的再利用
有助于防止环境污染,并降低对原材料的
需求。
地法可能求由市政废物理点向您出售新产
的零商提从家庭中分类收电产品的服务。
备注
史丹利的政策是持续改善我们的产品,因此,我
们保留随时变更产品规格的权利,恕不另行通
知。
标准设备和配件可能会根据不同的国家而有所
不同
简体中
10
产品规格可能会根据不同的国家而有所不同。
并非所有的国家都有提供完整的产品系列。
需各产品系列的供应情况,请联络您当地的
得代理商
制造商:史丹利五金工具(上海)有限公
制造商地址:上海市外高桥保税区泰谷路88号丰谷
大楼六层676A室
产地:江苏启
N384577 01/2014
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Stanley STDR5510 ユーザーマニュアル

カテゴリー
パワーツール
タイプ
ユーザーマニュアル

他の言語で