6
3
2
D
B
A
C
7
6
8
5
4
3
9
1
2
3
Intended use
General safety rules
Warning! Read all instructions. Failure to follow all instructions
listed below may result in electric shock, fire and/or serious
injury. The term “power tool” in all of the warnings listed
below refers to your mains operated (corded) power tool or
battery operated (cordless) power tool.
SAVE THESE INSTRUCTIONS.
1. Work area
a. Keep work area clean and well lit. Cluttered and dark
areas invite accidents.
b. Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases
or dust. Power tools create sparks which may ignite the
dust or fumes.
c. Keep children and bystanders away while operating
a power tool. Distractions can cause you to lose control.
2. Electrical safety
a. Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs
with earthed (grounded) power tools. Unmodified
plugs and matching outlets will reduce risk of electric shock.
b. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock
if your body is earthed or grounded.
c. Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
d. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase the
risk of electric shock.
e. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
3. Personal safety
a. Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a
power tool while you are tired or under the influence
of drugs, alcohol or medication. A moment of
inattention while operating power tools may result in
serious personal injury.
b. Use safety equipment. Always wear eye protection.
Safety equipment such as dust mask, non-skid safety
shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personal injuries.
c. Avoid accidental starting. Ensure the switch is in
the off position before plugging in. Carrying power
tools with your finger on the switch or plugging in power
tools that have the switch on invites accidents.
d. Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal injury.
e. Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power tool
in unexpected situations.
f. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
g. If devices are provided for the connection of dust
extraction and collection facilities, ensure these
are connected and properly used. Use of these
devices can reduce dust related hazards.
4. Power tool use and care
a. Do not force the power tool. Use the correct power
tool for your application. The correct power tool will do
the job better and safer at the rate for which it was designed.
Use clamps or another practical way to secure and
support the workpiece to a stable platform. Holding
the work by hand or against your body leaves it unstable
and may lead to loss of control.
Before drilling into walls, floors or ceilings check for the
location of wiring and pipes.
Avoid touching the tip of a drill bit just after drilling, as it
may be hot.
h.
ENGLISH
SPECIFICATION STEL101
POWER
NO-LOAD SPEED
REVERSE
MAX.DRILLING CAPACITY
-STEEL
-WOOD
CABLE LENGTH
––––––––––––––––––––––––––––––––––––––––––––––––––––––
––––––––––––––––––––––––––––––––––––––––––––––––––––––
STEL101
10mm Rotary Drill
Technical data
Your Stanley rotary drill has been designed for drilling in wood,
steel.
W
/min
mm
mm
m
400
0-2700
Yes
10
20
2
4
g. Use the power tool, accessories and tool bits etc.,
in accordance with these instructions and in the
manner intended for the particular type of power
tool, taking into account the working conditions
and the work to be performed. Use of the power tool
for operations different from those intended could result
in a hazardous situation.
5. Service
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
Removing and refitting the chuck (fig. C)
Open the chuck as far as possible.
Remove the chuck retaining screw, located in the chuck,
by turning it clockwise using a screwdriver.
Tighten an Allen key into the chuck and strike it with
a hammer as shown.
Remove the Allen key.
Remove the chuck by turning it counterclockwise.
To refit the chuck, screw it onto the spindle and secure it
with the chuck retaining screw.
f. Keep cutting tools sharp and clean. Properly maintained
cutting tools with sharp cutting edges are less likely to
bind and are easier to control.
Electrical safety
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
Features
This tool includes some or all of the following features.
1. Variable speed switch
2. Lock-on button
3. Forward/reverse slider
4. Chuck
9. Speed dial
Assembly
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Keyed chuck (fig. B)
Open the chuck by turning the sleeve (5) counterclockwise.
Insert the bit shaft (6) into the chuck.
Insert the chuck key (7) into each hole (8) in the side of
the chuck and turn clockwise until tight.
Use
Warning! Let the tool work at its own pace. Do not overload.
Warning! Before drilling into walls, floors or ceilings,
check for the location of wiring and pipes.
Selecting the direction of rotation (fig. D)
For drilling use forward (clockwise) rotation. For removing
a jammed drill bit, use reverse (counterclockwise) rotation.
To select forward rotation, push the forward/reverse
slider (3) to the left.
To select reverse rotation, push the forward/reverse slider
to the right.
Warning! Never change the direction of rotation while the
motor is running.
ENGLISH
e. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tools
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
b. Do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
c. Disconnect the plug from the power source before
making any adjustments, changing accessories, or
storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained users.
Safety warnings for drill
Wear ear protectors when impact drilling. Exposure
to noise can cause hearing loss.
Use auxiliary handle(s), if supplied with the tool.
Loss of control can cause personal injury.
Hold power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring or its own
cord. Cutting accessory contacting a "live" wire may make
exposed metal parts of the power tool "live" and could give
the operator an electric shock.
Warning! If the power cord is damaged, it
must be replaced by the manufacturer,
authorized Stanley Service Center or an
injury. If the power cord is replaced by an equally
warranty will not be valid.
equally qualified persion in order to avoid damage or
equally person, but not authorized by Stanley, the
5
Protecting the environment
Separate collection. This product must not be
disposed of with normal household waste.
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand for
raw materials.
Local regulations may provide for separate collection of
electrical products from the household, at municipal waste
sites or by the retailer when you purchase a new product.
ENGLISH
Maintenance
Your tool has been designed to operate over a long period of
time with a minimum of maintenance. Continuous satisfactory
operation depends upon proper tool care and regular cleaning.
Warning! Before performing any maintenance, switch off and
unplug the tool.
Regularly clean the ventilation slots in your tool using a
soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.
Should you find one day that your Stanley product needs
replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product
available for separate collection.
Switching on and off
To switch the tool on, press the variable speed switch (1).
The tool speed depends on how far you press the switch.
For continuous operation, press the lock-on button (2) and
release the variable speed switch. This option is available
only at full speed.
To switch the tool off, release the variable speed switch.
Based on the different applications, turn around the speed
dial (9) to control the maximum speed.
To switch the tool off when in continuous operation, press
the variable speed switch once more and release it.
Accessories
The performance of your tool depends on the accessory
used.Stanley and Piranha accessories are engineered tohigh
quality standards and designed to enhance theperformance
of your tool. By using these accessories you willget the very
best from your tool.
6
Stanley
/
1.
a.
b.
c.
2.
a.
b.
c.
d.
STEL101
W 400
/ 0-2700
- mm 10
- mm 20
m 2
e.
3.
a.
b.
c.
d.
e.
f.
g.
h.
4.
a.
b.
STEL 101
10mm
7
c.
d.
e.
f.
g.
5.
a.
u
u
u
Stanley
Stanley
1.
2.
3. /
4.
9.
B
u (5)
u (6)
u (7) (8)
C
u
u
u
u
u
u
D
u / (3)
u /
8
(1)
(2)
(9)
(9)
Stanley
Stanley
:
:
: 02-29994633
02/14
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
