TP-LINK TL-SG116 インストールガイド

カテゴリー
ネットワークスイッチ
タイプ
インストールガイド

このマニュアルも適しています

Installation Guide
© 2020 TP-Link
7106508660 REV6.0.0
5/8/16-Port Gigabit Desktop Switch
Note:
For simplicity, we will take TL-SG108 for example throughout this Guide.
On: Power on
O: Power o
LED Explanation
Power
Connection
Ethernet Ports (1-8)
PC PC
Router
LAN PortWAN Port
Internet
TL-SG108
Power Adapter
Link/Act
1000M (Green)
On: Running at 1000 Mbps
10/100M (Yellow)
On: Running at 10/100 Mbps
Link/Act (For TL-SG116)
Flashing: Transmitting/receiving data
Link/Act (For TL-SG105/TL-SG105S/TL-SG108/TL-SG108S)
Link/Act (Green)
Running at 10/100/1000 Mbps
O:
Flashing: Transmitting/receiving data
No device is linked to the
corresponding port
On:
Flashing: Transmitting/receiving data
Standard
Protocol
Interface
Use only power supplies which are provided by manufacturer and in the origin
packing of this product. If you have any questions, please don’t hesitate to contact us.
Safety Information
Do not use any other chargers than those recommended.
Keep the device away from water, re, humidity or hot environments.
Adapter shall be installed near the equipment and shall be easily accessible.
Do not use damaged charger or USB cable to charge the device.
Do not attempt to disassemble, repair, or modify the device.
EU declaration of conformity
TP-Link hereby declares that the device is in compliance with the essential requirements and
other relevant provisions of directives 2014/30/EU, 2014/35/EU, 2009/125/EC, 2011/65/EU
and (EU)2015/863.
The original EU declaration of conformity may be found at https://www.tp-link.com/en/ce.
Specications
General Specications
Data Transfer Rate
Network Media (Cable)
LED Indicators
Advanced Features
Transfer Method
MAC Address Learning
Frame Forward Rate
Operating Temperature
Storage Temperature
Operating Humidity
Storage Humidity
Environmental and Physical Specications
0 ˚C to 40 ˚C (32 ˚F to 104 ˚F)
-40 ˚C to 70 ˚C (-40 ˚F to 158 ˚F)
10% to 90%RH non-condensing
5% to 90%RH non-condensing
Wall Mountable
Distance Between
Mounting Holes
Ye s
TL-SG105/TL-SG105S: 52 mm
TL-SG108/TL-SG108S: 110 mm
TL-SG116: 200 mm
10Base-T: 14881pps/Port
100Base-TX: 148810pps/Port
1000Base-T: 1488095pps/Port
IEEE802.3, IEEE802.3i, IEEE802.3u, IEEE802.3ab,
IEEE802.3x, IEEE802.1p
CSMA/CD
Ethernet:
10 Mbps (Half Duplex), 20 Mbps (Full Duplex)
Fast Ethernet:
100 Mbps (Half Duplex), 200 Mbps (Full Duplex)
Gigabit Ethernet:
2000 Mbps (Full Duplex)
10Base-T:
UTP category 3, 4, 5 cable (maximum 100 m)
EIA/TIA-568 100
Ω
STP (maximum 100 m)
100Base-TX:
UTP category 5, 5e cable (maximum 100 m)
EIA/TIA-568 100
Ω
STP (maximum 100 m)
1000Base-T:
UTP category 5e cable (maximum 100 m)
EIA/TIA-568 100 Ω STP (maximum 100 m)
5/8/16 10/100/1000 Mbps Auto-Negotiation
RJ45 Ports
Power, Link/Act LED
IGMP Snooping, QoS (802.1p/DSCP Priority)
Store-and-Forward
Automatically learning, automatically aging
Q1. The Power LED is not lit.
Q2. The Link/Act LED is not lit when a device is connected
to the corresponding port.
Frequently Asked Questions (FAQ)
The Power LED should be lit when the power system is working
normally. If the Power LED is not lit, check as follows:
A1:
Make sure the power adapter is connected to the switch with
power source properly.
A2:
Make sure the voltage of the power supply meets the requirements
of the input voltage of the switch.
A3:
Make sure the power source is ON.
It is recommended that you check the following items:
A1:
Make sure that the cable connectors are rmly plugged into the
switch and the device.
A2:
Make sure the connected device is turned on and works normally.
A3:
The cable must be less than 100 meters long (328 feet).
For technical support and other information, please visit
https://www.tp-link.com/support, or simply scan the QR
code.
If you have any suggestions or needs on the product
guides, welcome to email techwriter@tp-link.com.cn.
To ask questions, find answers, and communicate with TP-Link users or
engineers, please visit https://community.tp-link.com to join TP-Link
Community.
For TL-SG116
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
For TL-SG105/TL-SG105S/TL-SG108/TL-SG108S
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communication. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment o and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/ TV technician for help.
For TL-SG116/TL-SG105/TL-SG105S/TL-SG108/TL-SG108S
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference that may
cause undesired operation.
Any changes or modications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
We, TP-Link USA Corporation, has determined that the equipment shown as above has
been shown to comply with the applicable technical standards, FCC part 15. There is no
unauthorized change is made in the equipment and the equipment is properly maintained
and operated.
Issue Date: 2020.2.14
FCC compliance information statement
Product Name: Gigabit Desktop Switch
Model Number: TL-SG105/TL-SG105S/TL-SG108/TL-SG108S/TL-SG116
Responsible party:
TP-Link USA Corporation, d/b/a TP-Link North America, Inc.
Address: 145 South State College Blvd. Suite 400, Brea, CA 92821
Website: https://www.tp-link.com/us/
Tel: +1 626 333 0234
Fax: +1 909 527 6803
FCC compliance information statement
Product Name: I.T.E. POWER SUPPLY
Model Number: T050060-2B1/T090060-2B1/T120100-2B1
Responsible party:
TP-Link USA Corporation, d/b/a TP-Link North America, Inc.
Address: 145 South State College Blvd. Suite 400, Brea, CA 92821
Website: https://www.tp-link.com/us/
Tel: +1 626 333 0234
Fax: +1 909 527 6803
Component Name Model
I.T.E. POWER SUPPLY
T050060-2B1 (for TL-SG105/TL-SG105S)
T090060-2B1 (for TL-SG108/TL-SG108S)
T120100-2B1 (for TL-SG116)
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communication. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment o and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/ TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference that may
cause undesired operation.
Any changes or modications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
We, TP-Link USA Corporation, has determined that the equipment shown as above has
been shown to comply with the applicable technical standards, FCC part 15. There is no
unauthorized change is made in the equipment and the equipment is properly maintained
and operated.
Issue Date: 2020.2.14
Explanation of the symbols on the product label
DC voltage
Indoor use only
RECYCLING
This product bears the selective sorting symbol for Waste electrical and electronic
equipment (WEEE). This means that this product must be handled pursuant to
European directive 2012/19/EU in order to be recycled or dismantled to minimize its
impact on the environment.
User has the choice to give his product to a competent recycling organization or to
the retailer when he buys a new electrical or electronic equipment.
限用物質含有情況標示聲明書
限用物質及其化學符號
Pb
Cd
Hg
六價鉻
Cr
+6
多溴聯苯
PBB
多溴二苯醚
PBDE
產品元件名稱
PCB
外殼
電源供應器
備考1. “系指該項限用物質之百分比含量未超出百分比含量基準值。
備考2. “系指該項限用物質為排除項目。
BSMI Notice
安全諮詢及注意事項
請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。
清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行清潔。
注意防潮請勿將水或其他液體潑灑到本產品上。
插槽與開口供通風使用以確保本產品的操作可靠並防止過熱請勿堵塞或覆蓋開口。
請勿將本產品置放於靠近熱源的地方。除非有正常的通風否則不可放在密閉位置中。
請不要私自打開機殼不要自行維修此產品若有損壞請聯繫廠家維修。
此為甲類資訊技術設備于居住環境中使用時可能會造成射頻擾動在此種情況下使用者會被要
求採取某些適當的對策。(For TL-SG116)
Industry Canada Statement
CAN ICES-3 (A)/NMB-3(A) (For TL-SG116)
CAN ICES-3 (B)/NMB-3(B) (For TL-SG105/TL-SG105S/TL-SG108/TL-SG108S)
TL-SG116 is a class A product, TL-SG105/TL-SG105S/TL-SG108/TL-SG108S is a class B
product. In a domestic environment, this product may cause radio interference, in which
case the user may be required to take adequate measures.
の装置は、スA情報技術装置の装置を家庭環境で使用電波妨害を
の場合には使用者が適切な対策を講ず要求れるがあ
VCCI-A (For TL-SG116)
Mounting Requirements
For TL-SG105/TL-SG116/TL-SG105S
To mount the device on a wall, use 2 screws which complies with ANSI B1.1 4#, (5#), 6#
standard and are more than 7 mm in length. When the screws are xed on the wall, the
distance between the screw head and the wall should be more than 1.5 mm.
For TL-SG108/TL-SG108S
To mount the device on a wall, use 2 screws which complies with ANSI B1.1 4#, (5#), 6#, 8#
standard and are more than 8.5 mm in length. When the screws are xed on the wall, the
distance between the screw head and the wall should be more than 1.5 mm.
  • Page 1 1
  • Page 2 2
  • Page 3 3

TP-LINK TL-SG116 インストールガイド

カテゴリー
ネットワークスイッチ
タイプ
インストールガイド
このマニュアルも適しています

他の言語で