7106507954 REV2.0.0
JetStream 8-Port Gigabit Smart Switch
T1500G-8T (TL-SG2008)
1. To access the GUI of the switch, open a browser and type the default
management address http://192.168.0.1 in the address eld of the
browser, then press the Enter key.
Note:
To log in to the switch, the IP address
of your PC should be set in the same
subnet as that of the switch. The IP
address is 192.168.0.x (”x” is any
number from 2 to 254). Subnet Mask
is 255.255.255.0. For details, please
refer to Appendix B in the User Guide
on the resource CD.
2. Enter admin for both the Username
and Password in the lower case
letters. Then click the Log In button or
press the Enter key.
3. After a successful login, the main
page will appear. You can click the
menus on the top side and left side
to congure the corresponding
functions.
Note:
For more details about how to congure the switch, see the Conguration
Guide on the resource CD.
PCPSE
Note:
1. Port 8 is a PD (Powered Device) port that supports being powered by a PSE
(Power Sourcing Equipment) complying with 802.3af standard.
2. The DC power input takes precedence over the PD port. If the DC input fails,
the PoE input on the PD port will supply power instead.
LED Explanation
Installation Guide
Conguration
Connection
On: Power on
O: Power o
Power
Power
Flashing: System running normally
On/O: System running abnormally
System
System
10/100/1000Mbps
On (Green): Running at1000Mbps
On (Yellow): Running at 10/100Mbps
Flashing: Transmitting/receiving data
1
2
3
4
5
6
7
8
Ethernet Ports (1-8)
DC Power Adapter
AC Power Cord
1
2
3
Environmental and Physical Specications
Operating Temperature
Storage Temperature
Operating Humidity
Storage Humidity
0˚C to 40˚C (32˚F to 104˚F)
-40˚C to 70˚C (-40˚F to 158˚F)
10% to 90% non-condensing
5% to 90% non-condensing
Frequently Asked Questions (FAQ)
The Power LED should be lit when the power system is working normally. If the
Power LED is not lit, please check as follows:
A1:
Make sure the AC power cord is connected to the switch with power source
properly.
A2:
Make sure the voltage of the power supply meets the requirements of the
input voltage of the switch.
A3:
Make sure the power source is ON.
Q1. The Power LED is not lit.
Standard
IEEE802.3i, IEEE802.3u, IEEE802.3ab,
IEEE802.3ad, IEEE802.3af, IEEE802.3x,
IEEE802.1p, IEEE802.1q, IEEE802.1d,
IEEE802.1x, IEEE802.1s, IEEE802.1w
CSMA/CD
Ethernet:10Mbps (Half Duplex) 20Mbps (Full Duplex)
Fast Ethernet: 100Mbps (Half Duplex) 200Mbps (Full Duplex)
Gigabit Ethernet: 2000Mbps (Full Duplex)
10Base-T:
UTP Cat. 3, 4, 5 cable (maximum 100m) EIA/TIA-568 100
STP (maximum 100m)
100Base-TX:
UTP of Cat. 5 or above (maximum 100m)
EIA/TIA-568 100 STP (maximum 100m)
1000Base-T:
UTP of Cat. 5e or above (maximum 100m)
EIA/TIA-568 100 STP (maximum 100m)
8 10/100/1000Mbps Auto-Negotiation RJ45 ports
PD Port: Port8
Power, System, 1-8
Store and Forward
Automatically learning, automatically aging
10Base-T: 14881pps/Port
100Base-Tx: 148810pps/Port
1000Base-T: 1488095pps/Port
Protocol
Data Transfer Rate
Network Media (Cable)
Type of Ports
LED Indicators
Transfer Method
MAC Address Learning
Frame Forward Rate
General Specications
It is recommended that you check the following items:
A1:
Make sure that the cable connectors are rmly plugged into the switch and
the device.
A2:
Make sure the connected device is turned on and works normally.
A3:
The cable must be less than 100 meters long (328 feet).
Q2. The 10/100/1000Mbps LED is not lit when a device is
connected to the corresponding port.
Specications
© 2018 TP-Link
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference that may cause undesired
operation.
Any changes or modications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
FCC STATEMENT
TP-Link hereby declares that the device is in compliance with the essential requirements and other
relevant provisions of directives 2014/30/EU, 2014/35/EU, 2009/125/EC and 2011/65/EU.
The original EU declaration of conformity may be found at http://www.tp-link.com/en/ce.
EU declaration of conformity
This is a class A product. In a domestic environment, this
product may cause radio interference, in which case the
user may be required to take adequate measures.
CE Mark Warning
Avoid using this product during an electrical storm. There may be a remote risk of electric shock from
lightning.
Keep the device away from water, re, humidity or hot environments.
Do not attempt to disassemble, repair, or modify the device.
Do not use any other chargers than those recommended.
Adapter shall be installed near the equipment and shall be easily accessible.
Safety Information
Industry Canada Statement
CAN ICES-3 (A)/NMB-3(A)
Indoor use only
Explanation of the symbols on the product label
DC voltage
RECYCLING
This product bears the selective sorting symbol for Waste electrical and electronic equipment
(WEEE). This means that this product must be handled pursuant to European directive
2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment.
User has the choice to give his product to a competent recycling organization or to the retailer
when he buys a new electrical or electronic equipment
Продукт сертифіковано згідно с правилами системи
УкрСЕПРО на відповідність вимогам нормативних
документів та вимогам, що передбачені чинними
законодавчими актами України.
BSMI Notice
安全諮詢及注意事項
請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。
清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行清潔。
注意防潮，請勿將水或其他液體潑灑到本產品上。
插槽與開口供通風使用，以確保本產品的操作可靠並防止過熱，請勿堵塞或覆蓋開口。
請勿將本產品置放於靠近熱源的地方。除非有正常的通風，否則不可放在密閉位置中。
請不要私自打開機殼，不要嘗試自行維修本產品，請由授權的專業人士進行此項工作。
此為甲類資訊技術設備，于居住環境中使用時，可能會造成射頻擾動，在此種情況下，使用者會
被要求採取某些適當的對策。
For technical support, Conguration Guide and other information,
please visit http://www.tp-link.com/support, or simply scan the QR
code.
Please read and follow the above safety information when operating the device. We cannot guarantee
that no accidents or damage will occur due to improper use of the device. Please use this product with
care and operate at your own risk.
限用物質含有情況標示聲明書
產品元件名稱
限用物質及其化學符號
PCB
外殼
電源適配器
鉛
Pb
鎘
Cd
汞
Hg
六價鉻
CrVI
多溴聯苯
PBB
多溴二苯醚
PBDE
備考1. "超出0.1 wt %" 及 "超出0.01 wt %" 系指限用物質之百分比含量超出百分比含量基準值。
備考2. "○"系指該項限用物質之百分比含量未超出百分比含量基準值。
備考3. " - " 系指該項限用物質為排除項目。
-
-
1
-
2
他の言語で
- English: TP-LINK T1500G-8T Installation guide
関連論文
-
TP-LINK TL-SG116 取扱説明書
-
TP-LINK TL-SG1005D インストールガイド
-
TP-LINK TL-SF1008D ユーザーマニュアル
-
TP-LINK TL-SG1005LP 16 Port Gigabit Desktop PoE Switch インストールガイド
-
TP-LINK TL-SF1016D インストールガイド
-
-
TP-LINK TL-R600VPN ユーザーマニュアル
-
-
TP-LINK MC220L Quick Installation Guide
-
TP-LINK UE200 ユーザーガイド
