ZyXEL Communications P-334WT クイックスタートガイド

P-334WT

802.11g Wireless Broadband Router with Firewall

Quick Start Guide

Version 3.60

1/2006

Table of Contents

ENGLISH 3

DEUTSCH 19

ESPAÑOL 36

FRANÇAIS 53

ITALIANO 70

繁體中文 87

ENGLISH

3

Overview

The P-334WT is a broadband router with a built-in four-port 10/100 Mbps switch. The P-334WT makes it easy

to set up a small home or office network and share Internet access via a broadband (cable/DSL) modem.

You should have an Internet account already set up and have been given most of the following information.

Table 1 Internet Account Information

See your User’s Guide for background information on all features.

The follow lists what you need to do:

Your device’s WAN IP Address (if given): ______________

DNS Server IP Address (if given): Primary _____________, Secondary ______________

Connection Type:

Ethernet Service Type: _______________________

User Name: ____________

Login Server IP Address: ______________

Password: ____________

PPTP: User Name: ____________

Your WAN IP Address (if given) ____________

Connection ID (if required): ____________

Password: ____________

PPTP Server IP Address: ___________

or PPTP Domain Name: ___________

¦PPPoE (PPPoE) Service Name: ____________

User Name: ____________ Password: ____________

1 Hardware Connections 2 Accessing the Web Configurator

3 Internet Access Setup

ENGLISH

4

1 Hardware Connections

Do the following to make hardware connections for initial setup.

WAN Connection

Connect your modem to the “WAN” port using the cable that came with your modem.

LAN Connection

Connect your computer to a "LAN" port using the included Ethernet cable

POWER Connection

Use the included power adaptor to connect the POWER socket to an appropriate power source (see the User’s

Guide for power adaptor specifications by region).

The LEDs

Look at the front panel LEDs. When

you connect the power, the PWR and

WLAN LEDs come on.

The LAN and WAN LEDs turn on if the

corresponding connections are

properly made.

1

2

3

ENGLISH

5

2 Accessing the Web Configurator

1 Launch your web browser. Enter “192.168.1.1” as the web site address.

Note: If you do not see the next screen, then please go to section 4.1.

Note: The Next button is located on the bottom right of each screen.

2 The Password window displays. Enter the

password (“1234” is the default) and click Login.

3 Change the password in the screen that follows

and click Apply.

4 Click Go to Wizard setup and click Apply to set up

your P-334WT for the first time.

5 Choose your language from the drop-down list

box. Click Next.

6 Click Next to proceed with the Connection Wizard.

ENGLISH

6

3 Internet Access Setup

Note: Enter the Internet access information exactly as given to you by your ISP in each wizard screen

and then click Next to continue or click Back to return to the previous screen.

Current screen information will be lost if you click Back.

System Information

Wireless LAN

Configure ONE of the following wireless security types on the P-334WT:

• Auto security: Use OTIST to automatically generate a pre-shared key. View the generated pre-shared key in

the Wireless LAN screen.

Note: Your wireless clients must support WPA-PSK and use the same key.

• None: Have no wireless LAN security configured. If you do not enable any wireless security on your P-334WT,

your network is accessible to any wireless networking device that is within range.

• Basic security: WEP (Wired Equivalent Privacy) encrypts data frames before transmitting over the wireless net-

work. The higher the WEP Encryption, the higher the security but the slower the throughput.

• Extend (WPA-PSK or WPA2-PSK) security: Configure a Pre-Shared Key. Choose this option only if your wire-

less clients support WPA-PSK or WPA2-PSK respectively.

Note: The wireless clients and P-334WT must use the same SSID, channel ID and WPA(2)-PSK (if

WPA(2)-PSK is enabled) or WEP encryption key (if WEP is enabled) for wireless communication.

1 This screen is optional. You can just click Next.

• System Name is for identifying the P-334WT. You

can enter your computer's "Computer Name".

• If you leave the Domain Name blank, the domain

name obtained by DHCP from the ISP is used.

STEP 1:

STEP 2:

ENGLISH

7

OTIST

• OTIST (One-Touch Intelligent Security Technology) allows your P-334WT to assign wireless clients the P-

334WT’s SSID and static WEP or WPA-PSK encryption settings. The wireless client must also support OTIST

and have OTIST enabled.

A Enter a unique name to identify the P-334WT in the wireless LAN.

B Leave the default setting. The P-334WT and wireless client must use the same channel ID.

C Select a level of wireless security. Choose Auto or None.

D Yes is selected by default. Select the No radio button if you don’t want to use OTIST now or your wireless

clients don’t support OTIST. If you set Security to Auto, OTIST must be enabled.

E The default OTIST Setup Key is “01234567”. This key can be changed in the OTIST screen. Be sure to use

the same OTIST Setup Key on the P-334WT and wireless clients.

Auto or No Wireless Security

D

E

A

B

C

ENGLISH

8

A Enter a unique name to identify the P-334WT in the wireless LAN.

B Leave the default setting. The P-334WT and wireless client must use the same channel ID.

C Select Basic(WEP) security.

D Select 64-bit, 128-bit or 256-bit from the WEP Encryption drop-down list.

E Select ASCII or Hex WEP key input method.

F You can create a WEP key by either:

Entering a Passphrase (up to 32 printable characters) and clicking Generate to have the P-334WT

automatically generates a WEP key.

Or

Entering manual keys in each Key (1~4) field.

G Select one of the Key radio buttons to use as the default WEP key.

H Yes is selected by default. Select the No radio button if you don’t want to use OTIST now or your wireless

clients don’t support OTIST.

I The default OTIST Setup Key is “01234567”. This key can be changed in the OTIST screen. Be sure to use

the same OTIST Setup Key on the P-334WT and wireless clients.

Basic(WEP) Security

ENGLISH

9

E

F

D

G

A

B

C

H

I

ENGLISH

10

A Enter a unique name to identify the P-334WT in the wireless LAN.

B Leave the default setting. The P-334WT and wireless client must use the same channel ID.

C Select WPA-PSK or WPA2-PSK security.

D Type a pre-shared key to have a more secure wireless connection than WEP encryption. Type from 8 to 63

case-sensitive ASCII characters.You can set up the most secure wireless connection by configuring WPA in

the advanced wireless screen. You need to configure a RADIUS server to do this.

E Yes is selected by default. Select the No radio button if you don’t want to use OTIST now or your wireless

clients don’t support OTIST.

F The default OTIST Setup Key is “01234567”. This key can be changed in the OTIST screen. Be sure to use

the same OTIST Setup Key on the P-334WT and wireless clients.

Extend (WPA-PSK or WPA2-PSK) Security

A

B

C

D

E

F

ENGLISH

11

WAN

The wizard attempts to detect which WAN connection type you are using.

If the wizard does not detect a connection type, you must select ONE from the drop-down list box. Check with your

ISP to make sure you use the correct type:

1 Ethernet

2 PPPoE

3 PPTP.

Note: If you were given Internet access settings, enter them in the following fields. Otherwise leave the

default settings and just click Next.

A Select Ethernet as your WAN connection type.

B Select Get automatically from your ISP if your ISP did not assign you a fixed IP address. Skip to C.

Or

Select Use fixed IP address provided by your ISP to give the P-334WT a fixed, unique IP address. Go to

B1.

B1 If you select Use fixed IP address provided by your ISP, enter a WAN IP address, WAN IP Subnet Mask

and the neighboring device’s IP address given by your ISP.

If you were given DNS server settings, enter them in the fields. Otherwise leave the default settings and

just click Next.

C Select Factory Default to use the factory assigned default MAC address.

D Select the check box to have the P-334WT apply bandwidth management to traffic going out through the P-

334WT’s WAN, LAN or WLAN port according to the traffic type.

E Click Apply to save your changes.

STEP 3:

Ethernet Connection

ENGLISH

12

A

B

C

B1

D

E

ENGLISH

13

A Select PPPoE as your WAN connection type.

B Type a Service Name (Optional), User Name and Password.

C Select Get automatically from your ISP if your ISP did not assign you a fixed IP address. Skip to D.

Or

Select Use fixed IP address provided by your ISP to give the P-334WT a fixed, unique IP address. Go to

C1.

C1 If you select Use fixed IP address provided by your ISP, enter a WAN IP address, WAN IP Subnet Mask

and the neighboring device’s IP address given by your ISP.

If you were given DNS server settings, enter them in the fields. Otherwise leave the default settings and just

click Next.

D Select Factory Default to use the factory assigned default MAC address.

E Select the check box to have the P-334WT apply bandwidth management to traffic going out through the P-

334WT’s WAN, LAN or WLAN port according to the traffic type.

F Click Apply to save your changes.

PPPoE Connection

ENGLISH

14

A

B

C

C1

D

E

F

ENGLISH

15

A Select PPTP as your WAN connection type.

B Type a User Name and Password.

C Select Get automatically from ISP if your ISP did not assign you a fixed PPTP IP address.

Or select Use fixed IP address to give the P-334WT a fixed, unique PPTP IP address and subnet mask.

D Type a PPTP Server IP Address.

E Type a Connection ID/Name (if provided).

F Select Get automatically from your ISP if your ISP did not assign you a fixed IP address. Skip to G.

Or

Select Use fixed IP address provided by your ISP to give the P-334WT a fixed, unique IP address. Go to

F1.

F1 If you select Use fixed IP address provided by your ISP, enter a WAN IP address, WAN IP Subnet Mask

and the neighboring device’s IP address given by your ISP.

If you were given DNS server settings, enter them in the fields. Otherwise leave the default settings and

just click Next.

G Select Factory Default to use the factory assigned default MAC address.

H Select the check box to have the P-334WT apply bandwidth management to traffic going out through the P-

334WT’s WAN, LAN or WLAN port according to the traffic type.

I Click Apply to save your changes.

PPTP Connection

ENGLISH

16

B

C

D

E

A

F

F1

G

H

I

ENGLISH

17

Internet Access Setup Complete

4 Troubleshooting

Note: If your computer cannot automatically communicate with the device, then see the multimedia

tutorial on how to set up your computer to receive an IP address dynamically or give it a fixed

one in the range specified in section

4.1.

If you have any Internet access problems, follow the

on-screen instructions.

Click Finish to complete the wizard setup.

PROBLEM CORRECTIVE ACTION

None of the LEDs turn on when

you connect the P-334WT’s

power.

Make sure that you have the correct power adaptor connected to the P-334WT,

it is plugged into an appropriate power source.

Check all cable connections. If the LEDs still do not turn on, you may have a

hardware problem. In this case, you should contact your local vendor.

Cannot access the P-334WT

from my computer.

Check the cable connection from your computer to the P-334WT.

If the P-334WT’s IP address has changed, then enter the new one as the

website address.

Make sure your computer’s IP address is in the same subnet as the P-334WT’s

IP address (see section 4.1).

Ping the P-334WT from a computer on the LAN. Make sure your computer’s

Ethernet adapter is installed and functioning properly. In the computer, click

Start, (All) Programs, Accessories and then Command Prompt. In the

Command Prompt window, type "ping" followed by the P-334WT’s LAN IP

address (192.168.1.1 is the default) and then press [ENTER]. The P-334WT

should reply; otherwise see section 4.1.

ENGLISH

18

4.1 Set Up Your Computer’s IP Address

This section shows you how to set your Windows NT/2000/XP computer to automatically get an IP address.

This ensures that your computer can communicate with your P-334WT. Refer to your User’s Guide for

detailed IP address configuration for other Windows and Macintosh computer operating systems.

1 In Windows XP, click start, Control Panel. In Windows 2000/NT, click Start, Settings, Control Panel.

2 In Windows XP, click Network Connections. In Windows 2000/NT, click Network and Dial-up

Connections.

3 Right-click Local Area Connection and then click Properties.

4 Select Internet Protocol (TCP/IP) (under the General tab in Win

XP) and click Properties.

5 The Internet Protocol TCP/IP Properties screen opens (the

General tab in Windows XP).

6 Select the Obtain an IP address automatically and Obtain

DNS server address automatically options.

7 Click OK to close the Internet Protocol (TCP/IP) Properties

window.

8 Click Close (OK in Windows 2000/NT) to close the Local Area

Connection Properties window.

9 Close the Network Connections screen.

Viewing Your Product’s Certifications

1 Go to www.zyxel.com.

2 Select your product from the drop-down list box on the ZyXEL home page to go to that product's page.

3 Select the certification you wish to view from this page.

Cannot access the P-334WT

from my computer (continued).

Use Internet Explorer 6.0 and later or Netscape Navigator 7.0 and later with

JavaScript enabled.

Make sure you enter the password correctly (the field is case sensitive).

If you’ve forgotten the P-334WT’s password, use the RESET button. Press the

button in for about 10 seconds (or until the SYS LED starts to blink), then

release it. It returns the P-334WT to the factory defaults (password is 1234, LAN

IP address 192.168.1.1 etc.).

Cannot access the Internet. Verify the Internet connection settings in the wizard. Make sure you entered the

correct user name and password if you are using PPPoE or PPPoA.

PROBLEM CORRECTIVE ACTION

DEUTSCH

19

Übersicht

Der P-334WT ist ein Breitband-Router mit einem integrierten 10/100 Mbps Schalter mit vier Anschlüssen. Mit

dem P-334WT können Sie ganz einfach ein kleines Heim- oder Büronetzwerk aufbauen und einen

Internetzugang von mehreren Rechnern aus über ein Breitbandmodem (Kabel/DSL) nutzen.

Voraussetzung sind ein bestehendes Internetkonto und die folgenden Informationen.

Tabelle 1 Daten zum Internetkonto

Ausführliche Informationen zu allen Funktionen finden Sie im Benutzerhandbuch.

Im Folgenden wird aufgeführt, welche Schritte notwendig sind:

Die WAN IP-Adresse Ihres Geräts (wenn vorhanden): ______________

DNS Server IP-Adresse (wenn vorhanden): Primär _____________, Sekundär ______________

Verbindungstyp:

Ethernet Diensttyp: _______________________

Benutzername: ____________

Login Server IP-Adresse: ______________

Passwort: ____________

PPTP: Benutzername: ____________

Ihre WAN IP-Adresse (wenn vorhanden)

____________

Verbindungs-ID (wenn erforderlich):

____________

Passwort: ____________

PPTP Server IP-Adresse: ___________

oder PPTP Domain-Name: ___________

PPPoE (PPPoE) Dienstname: ____________

Benutzername: ____________ Passwort: ____________

1 Anschließen der Hardware 2 Zugriff auf den Web-Konfigurator

3 Einrichten des Internetzugangs

DEUTSCH

20

1 Anschließen der Hardware

Bei der Erstinstallation müssen die folgenden Hardwareverbindungen hergestellt werden.

Herstellen der WAN-Verbindung

Schließen Sie Ihr Modem mit dem mitgelieferten Kabel an den WAN-Anschluss an.

Herstellen der LAN-Verbindung

Schließen Sie Ihren Computer mit dem mitgelieferten Ethernet-Kabel an einen "LAN"-Anschluss an.

Anschließen an das Stromnetz

Verbinden Sie den Netzanschluss des Geräts (POWER) mit dem mitgelieferten Netzadapter mit einer

geeigneten Stromquelle (eine nach Regionen geordnete Liste der Netzadapter-Spezifikationen finden Sie im

Benutzerhandbuch).

1

2

3

ページが読み込まれています...

ZyXEL Communications P-334WT クイックスタートガイド

ZyXEL Communications P-334WT クイックスタートガイド

他の言語で

関連論文

その他のドキュメント