ZyXEL Communications Network Card 5 ユーザーマニュアル

ZyWALL 5

Internet Security Appliance

Quick Start Guide

Version 4.04

3/2008

Edition 1

DEFAULT LOGIN

IP Address http://192.168.1.1

User Name admin

Password 1234

CONTENTS

ENGLISH 2

DEUTSCH 18

ESPAÑOL 36

FRANÇAIS 54

ITALIANO 72

РУССКИЙ 90

SVENSKA 108

简体中文

126

繁體中文

142

ENGLISH

2

Overview

The ZyWALL 5 is a firewall with VPN, bandwidth management, content filtering, anti-spam, anti-virus, IDP

(Intrusion Detection and Protection) and many other features. You can use it as a transparent firewall and not

reconfigure your network nor configure the ZyWALL’s routing features. When the ZyWALL is in router mode,

you can also insert a 3G wireless card to add a second WAN. The ZyWALL increases network security by

adding the option to change port roles from LAN to DMZ for use with publicly accessible servers. This guide

covers the initial connections and configuration needed to start using the ZyWALL in your network.

See the User’s Guide for more information on all features.

You may need your Internet access information.

This guide is divided into the following sections.

1 Hardware Connections

You need the following.

1 Hardware Connections

2 Accessing the Web Configurator

3 Bridge Mode

4 Internet Access Setup and Product Registration

5 DMZ

6 NAT

7 Firewall

8 VPN Rule Setup

9 Anti-Spam Setup

10Troubleshooting

ZyWALL Computer Ethernet Cables

Power Adaptor

ENGLISH

3

Do the following to make hardware connections for initial setup.

1 Use an Ethernet cable to connect the LAN/DMZ port to a computer. If you configure these ports as DMZ

ports in the LAN or DMZ screen through the web configurator, you can also use Ethernet cables to connect

public servers (web, e-mail, FTP, etc.) to the LAN/DMZ ports.

2 Use another Ethernet cable to connect the WAN port to an Ethernet jack with Internet access.

3 Insert the ZyWALL Turbo extension card to use the anti-virus and IDP features or insert a wireless LAN

card to use the wireless LAN feature. You can optionally insert a 3G wireless card to access the Internet

wirelessly via a 3G network. See the ZyWALL Turbo Card guide for more information about the extension

card. See the user’s guide about installing a wireless LAN card. At the time of writing, you can use the

following 3G wireless cards in the ZyWALL.

• Sierra Wireless AC850/860, AC595, AC875

ENGLISH

4

• Huawei E612, E620

• Option GlobeTrotter HSDPA 7.2 Ready

4 Use the included power adaptor to connect the power socket (on the rear panel) to a power outlet.

5 Look at the front panel. The PWR LED turns on. The SYS LED blinks while performing system testing and

then stays on if the testing is successful. The ACT, CARD, LAN/DMZ and WAN LEDs turn on and stay on

if the corresponding connections are properly made.

2 Accessing the Web Configurator

Use this section to configure the WAN 1 interface for Internet access.

5 The HOME screen opens.

The ZyWALL is in router mode by default. Continue to the next step if you want to use routing features such as

NAT, DHCP and VPN.

Go to Section 3 if you prefer to use the ZyWALL as a transparent firewall.

1 Launch your web browser. Enter 192.168.1.1 (the

ZyWALL’s default IP address) as the address.

If the login screen does not display, see Section

10.1 to set your computer’s IP address.

2 Click Login (the default password 1234 is already

entered).

3 Change the login password by entering a new

password and clicking Apply.

4 Click Apply to replace the ZyWALL’s default

digital certificate.

ENGLISH

5

6 Check the network status table. If the WAN 1 status is not Down and there is an IP address, go to Section

5.

If the WAN 1 status is Down (or there is not an IP address), click the Wizard icon and use Section 4 to

configure WAN 1.

Use the NETWORK WAN screens if you need to configure WAN 2. You can also configure load balancing

between the WAN connections.

3 Bridge Mode

When you set the ZyWALL to bridge mode, it functions as a transparent firewall. Do the following to set the

ZyWALL to bridge mode.

1 Click MAINTENANCE in the navigation

panel and then Device Mode.

2 Select Bridge and configure a (static)

IP address subnet mask and gateway

IP address for the ZyWALL’s LAN,

WAN, DMZ and WLAN interfaces.

3 Click Apply. The ZyWALL restarts.

Skip to Section 5 if you have servers that

you need to be accessible from the WAN.

ENGLISH

6

4 Internet Access Setup and Product Registration

1 Click the Wizard icon ( ) in the HOME screen and then

the Internet Access Setup link to open the Internet access

wizard.

Enter the Internet access information exactly as given to you.

If you were given an IP address to use, select Static in the IP

Address Assignment drop-down list box and enter the

information provided.

" The fields vary depending on what you select in

the Encapsulation field. Fill them in with the

information provided by the ISP or network

administrator.

Click Apply when you are done.

• PPP over Ethernet or PPTP Encapsulation

Select Nailed-Up when you want your connection up all the time (this could be expensive if your ISP bills you

for Internet usage time instead of a flat monthly fee).

• Ethernet Encapsulation

Configure a Roadrunner service in the

NETWORK WAN screens (use the WAN

tab).

ENGLISH

7

To not have the connection up all the time, specify an idle time-out period (in seconds) in Idle Timeout.

2 Click Next to display the screen where you can

register your ZyWALL with myZyXEL.com

(ZyXEL’s online services center) and activate the

free content filtering, anti-spam, anti-virus and IDP

trial applications. Otherwise, click Skip and then

Close to complete Internet access setup.

" Make sure you have installed the ZyWALL Turbo Card before you activate the IDP and anti-

virus subscription services.

Turn the ZyWALL off before you install or remove the ZyWALL Turbo Card.

ENGLISH

8

3 If you already have an account at

myZyXEL.com, select Existing myZyXEL.com

account and enter account information.

Otherwise, select New myZyXEL.com account

and fill in the fields below to create a new

account and register your ZyWALL. Click Next.

4 Wait for the registration progress to finish.

5 The following screen displays if the registration

was not successful. Click Return to go back to

the Device Registration screen and check your

settings.

6 Click Close to leave the wizard screen when

the registration and activation are done.

ENGLISH

9

" If you want to activate a standard service with your iCard’s PIN number (license key), use the

REGISTRATION Service screen. See the user’s guide for details.

5 DMZ

The DeMilitarized Zone (DMZ) allows public servers (web, e-mail, FTP, etc.) to be visible to the outside world

and still have firewall protection from DoS (Denial of Service) attacks.

You can assign TCP/IP configuration via DHCP to computers connected to the DMZ ports. Otherwise,

configure the computers with static IP addresses (in the same subnet as the DMZ port's IP address) and DNS

server addresses. Use the ZyWALL's DMZ IP address as the default gateway.

Do the following to configure the DMZ if the ZyWALL is in routing mode.

" You do not need to configure DMZ with bridge mode, skip to Section 7.

1 Click NETWORK > DMZ in the navigation panel.

2 Specify an IP address and subnet mask for the

DMZ interface.

If you use private IP addresses on the DMZ, use

NAT to make the servers publicly accessible (see

Section 6).

A public IP address must be on a separate subnet

from the WAN port’s public IP address. If you do

not configure NAT for the public IP addresses on

the DMZ, the ZyWALL routes traffic to the public IP

addresses on the DMZ without performing NAT.

This may be useful for hosting servers for NAT

unfriendly applications.

3 Click Apply.

4 By default, LAN/DMZ ports 1 to 4 are all LAN ports.

To configure a port as a DMZ port, click the Port

Roles tab, select its radio button next to DMZ and

click Apply.

ENGLISH

10

6 NAT

NAT (Network Address Translation - NAT, RFC 1631) means the translation of an IP address in one network

to a different IP address in another. You can use the NAT Address Mapping screens to have the ZyWALL

translate multiple public IP addresses to multiple private IP addresses on your LAN (or DMZ).

The following example allows access from the WAN1 to an HTTP (web) server on the DMZ. The server has a

private IP address of 10.0.0.20.

1 Click ADVANCED > NAT in the

navigation panel and then Port

Forwarding.

2 Select the WAN connection (WAN1) for

which you want to configure port

forwarding rules.

3 Select the Active check box.

4 Type a name for the rule.

5 Type the port number that the service

uses.

6 Type the HTTP server’s IP address.

7 Click Apply.

7 Firewall

You can use the ZyWALL without configuring the firewall.

The ZyWALL’s firewall is pre-configured to protect your LAN from attacks from the Internet. By default, no

traffic can enter your LAN unless a request was generated on the LAN first. The ZyWALL allows access to the

DMZ from the WAN or LAN, but blocks traffic from the DMZ to the LAN.

If you are using the ZyWALL in router mode, continue with the next section. For bridge mode, skip to Section

10.

ENGLISH

11

8 VPN Rule Setup

A VPN (Virtual Private Network)

tunnel gives you a secure

connection to another computer or

network.

A gateway policy identifies the

IPSec routers at either end of a VPN

tunnel.

A network policy specifies which

devices (behind the IPSec routers)

can use the VPN tunnel.

This figure helps explain the main fields in the wizard screens.

1 Click the Wizard icon ( ) in the HOME screen and then the VPN Setup link to open the VPN wizard.

" Your settings are not saved when you click Back.

2 Use this screen to configure the gateway policy.

Name: Enter a name to identify the gateway policy.

Remote Gateway Address: Enter the IP address or

domain name of the remote IPSec router.

ENGLISH

12

3 Use this screen to configure the network policy.

Leave the Active check box selected.

Name: Enter a name to identify the network policy.

Select Single and enter an IP address for a single IP

address.

Select Range IP and enter starting and ending IP

addresses for a specific range of IP addresses.

Select Subnet and enter an IP address and subnet

mask to specify IP addresses on a network by their

subnet mask.

" Make sure that the remote IPSec router uses the same security settings that you configure in

the next two screens.

Negotiation Mode: Select Main Mode for identity protection. Select Aggressive Mode to allow more incoming

connections from dynamic IP addresses to use separate passwords.

" Multiple SAs (security associations) connecting through a secure gateway must have the

same negotiation mode.

Encryption Algorithm: Select 3DES or AES for stronger (and slower) encryption.

Authentication Algorithm: Select MD5 for minimal security or SHA-1 for higher security.

Key Group: Select DH2 for higher security.

SA Life Time: Set how often the ZyWALL renegotiates the IKE SA (minimum 180 seconds). A short SA life

time increases security, but renegotiation temporarily disconnects the VPN tunnel.

Pre-Shared Key: Use 8 to 31 case-sensitive ASCII characters or 16 to 62 hexadecimal ("0-9", "A-F")

characters. Precede a hexadecimal key with a "0x” (zero x), which is not counted as part of the 16 to 62

character range for the key.

Encapsulation Mode: Tunnel is compatible with NAT, Transport is not.

IPSec Protocol: ESP is compatible with NAT, AH is not.

ENGLISH

13

Perfect Forward Secrecy (PFS): None allows faster IPSec setup, but DH1 and DH2 are more secure.

8.1 Using the VPN Connection

Use VPN tunnels to securely send and retrieve files, and allow remote access to corporate networks, web

servers and e-mail. Services work as if you were at the office instead of connected through the Internet.

4 Use this screen to configure IKE (Internet Key

Exchange) tunnel settings.

5 Use this screen to configure IPSec settings.

6 Check your VPN settings. Click Finish to save the

settings.

7 Click Close in the final screen to complete the

VPN wizard setup. Continue with the next section

to activate the VPN rule and establish a VPN

connection.

ENGLISH

14

For example, the “test” VPN rule allows

secure access to an web server on a

remote corporate LAN. Enter the server’s

IP address (10.0.0.23 in this example) as

your browser’s URL. The ZyWALL

automatically builds the VPN tunnel when

you attempt to use it.

Click SECURITY > VPN in the navigation

panel and then the SA Monitor tab to

display a list of connected VPN tunnels

(the “test” VPN tunnel is up here).

9 Anti-Spam Setup

Use anti-spam to have the ZyWALL check for unsolicited commercial or junk e-mail (spam).

" You must have already subscribed to the anti-spam service to use the feature (see page 6).

1 Click the Wizard icon in the HOME screen and then Anti-Spam Setup to open the anti-spam wizard.

2 Select the locations where you

have e-mail servers. An icon of an

e-mail server appears at each spot

you select. In this example the e-

mail servers are on the LAN.

" WAN 2 represents the 3G

wireless Internet

connection available when

you insert a 3G wireless

card (optional).

ENGLISH

15

You can also use the anti-spam whitelist and blacklist to identify legitimate e-mail and spam. See the anti-

spam chapter in the User’s Guide for details.

3 The ZyWALL recommends which

traffic flows to scan for spam based

on the locations of your e-mail

servers.

4 Use this screen to enable anti-

spam and select which traffic flows

the ZyWALL scans for spam. The

recommended traffic flows are

already selected. You generally

only need to select traffic directions

that have incoming e-mail from

outside e-mail servers.

5 Click Apply.

6 Click Close in the final screen to

complete the anti-spam wizard

setup.

7 Congratulations, you have

configured the ZyWALL to scan for

spam e-mail.

ENGLISH

16

10 Troubleshooting

10.1 Set Up Your Computer’s IP Address

This section shows you how to set up your computer to receive an IP address in Windows 2000, Windows NT

and Windows XP. This is ensures that your computer can communicate with your ZyWALL.

1 In Windows XP, click Start, Control Panel.

In Windows 2000/NT, click Start, Settings, Control Panel.

2 In Windows XP, click Network Connections.

In Windows 2000/NT, click Network and Dial-up Connections.

Problem Corrective Action

None of the LEDs turn

on.

Make sure that you have the power adaptor connected to the ZyWALL and plugged in to

an appropriate power source. Check all cable connections.

If the LEDs still do not turn on, you may have a hardware problem. In this case, you

should contact your local vendor.

Cannot access the

ZyWALL from the

LAN.

Check the cable connection between the ZyWALL and your computer or hub. Refer to

Section 1 for details.

Ping the ZyWALL from a LAN computer. Make sure your computer’s Ethernet card is

installed and functioning properly.

In the computer, click Start, (All) Programs, Accessories and then Command Prompt.

In the Command Prompt window, type "ping" followed by the ZyWALL’s LAN IP

address (192.168.1.1 is the default) and then press [ENTER]. The ZyWALL should reply.

Otherwise, refer to Section 10.1.

If you’ve forgotten the ZyWALL’s password, use the RESET button. Press the button in

for about 10 seconds (or until the SYS LED starts to blink), then release it. It returns the

ZyWALL to the factory defaults (password is 1234, LAN IP address 192.168.1.1 etc.; see

your User’s Guide for details).

If you’ve forgotten the ZyWALL’s LAN or WAN IP address, you can check the IP address

in the SMT via the console port. Connect your computer to the CONSOLE port using a

console cable. Your computer should have a terminal emulation communications

program (such as HyperTerminal) set to VT100 terminal emulation, no parity, 8 data bits,

1 stop bit, no flow control and 9600 bps port speed.

Cannot access the

Internet.

Check the ZyWALL’s connection to the Ethernet jack with Internet access. Make sure the

Internet gateway device (such as a DSL modem) is working properly.

Click WAN in the navigation panel to verify your settings.

Cannot establish a

VPN connection

Make sure the ZyWALL and the remote IPSec router use the same VPN settings. Click

VPN in the navigation panel to configure advanced settings.

Access a web site to check that you have a successful Internet connection.

ENGLISH

17

3 Right-click Local Area Connection and then click Properties.

4 Select Internet Protocol (TCP/IP) (under the General tab in Windows XP) and click Properties.

5 The Internet Protocol TCP/IP Properties screen opens

(the General tab in Windows XP). Select the Obtain an

IP address automatically and Obtain DNS server

address automatically options.

6 Click OK to close the Internet Protocol (TCP/IP)

Properties window.

7 Click Close (OK in Windows 2000/NT) to close the

Local Area Connection Properties window.

8 Close the Network Connections screen.

Procedure to View a Product’s Certification(s)

1 Go to www.zyxel.com.

2 Select your product from the drop-down list box on the ZyXEL home page to go to that product's page.

3 Select the certification you wish to view from this page.

DEUTSCH

18

Übersicht

Die ZyWALL 5 ist eine Firewall mit VPN, Bandbreitenmanagement, Content Filtering, Anti-Spam, Anti-Virus,

IDP (Intrusion Detection and Protection) und vielen anderen Funktionen. Sie können sie als transparente

Firewall verwenden, ohne das Netzwerk neu zu konfigurieren und die Routingfunktionen des Geräts zu

konfigurieren. Wenn sich der ZyWALL im Router-Modus befindet, können Sie auch eine 3G-Wireless-Card

einsetzen, um ein zweites WAN hinzuzufügen. Die ZyWALL bietet die Möglichkeit, bei der Benutzung öffentlich

zugänglicher Server die Portfunktionen zu wechseln (LAN zu DMZ) und erhöht damit die Netzwerksicherheit.

In dieser Anleitung finden Sie eine Beschreibung der Anschlüsse und der Konfiguration, die notwendig ist,

damit Sie die ZyWALL in Ihrem Netzwerk verwenden können.

Eine ausführliche Beschreibung aller Funktionen finden Sie im Benutzerhandbuch.

Bitte halten Sie die Daten für Ihren Internetzugang bereit.

Diese Anleitung ist in die folgenden Abschnitte aufgeteilt.

1 Anschließen der Hardware

Sie benötigen folgendes:

1 Anschließen der Hardware

2 Zugriff auf den Web-Konfigurator

3 Bridge Mode

4 Einrichten des Internetzugriffs und

Produktregistrierung

5 DMZ

6 NAT

7 Firewall

8 Einstellen der VPN-Regeln

9 Anti-Spam einrichten

10Problembeseitigung

ZyWALL Computer Ethernetkabel

Netzteil

DEUTSCH

19

Wenn Sie das Gerät installieren, müssen Sie die Hardwaregeräte folgendermaßen anschließen.

1 Verbinden Sie den LAN-/DMZ-Port mit einem Ethernet-Kabel mit dem Computer. Wenn Sie diese Ports im

LAN- oder DMZ-Fenster mit dem Web-Konfigurator als DMZ-Ports konfigurieren, können Sie auch mit

Ethernetkabeln eine Verbindung von LAN-/DMZ-Ports zu öffentlichen Servern (Internet, E-Mail, FTP usw.)

herstellen.

2 Schließen Sie mit einem anderen Ethernet-Kabel den WAN-Port an die Ethernet-Buchse mit Internetzugriff

an.

3 Wenn Sie die Antiviren- und IDP-Funktion verwenden möchten, müssen Sie die Erweiterungskarte

ZyWALL TURBO einsetzen. Sie können alternativ eine 3G-Wireless-Card einsetzen, um über ein 3G-

Netzwerk auf das Internet zuzugreifen. Fur die LAN-Funktion benötigen Sie die Wireless LAN-Karte.

DEUTSCH

20

Weitere Informationen zu den Erweiterungskarten erhalten Sie in der Bedienungsanleitung der ZyWALL

Turbo Karte. Eine Installationsanleitung fur eine Wireless LAN-Karte finden Sie im Benutzerhandbuch.

Zum Zeitpunkt der Drucklegung können Sie ZyWALL die folgenden 3G-Wireless-Cards verwenden.

• Sierra Wireless AC850/860, AC595, AC875

• Huawei E612, E620

• Option GlobeTrotter HSDPA 7.2 Ready

4 Schließen Sie das mitgelieferte Netzteil an der Rückseite der ZyWALL an.

5 Kontrollieren Sie den Systemstart mittels der LEDs an der Frontseite. Die PWR-LED beginnt zu leuchten.

Während des Systemtests blinkt die SYS-LED. Wurde der Test erfolgreich abgeschlossen, bleibt diese

Anzeige an. Die LEDs ACT, CARD, LAN/DMZ und WAN beginnen zu leuchten und bleiben an, wenn die

entsprechenden Verbindungen richtig hergestellt wurden.

2 Zugriff auf den Web-Konfigurator

In diesem Abschnitt wird beschrieben, wie die WAN 1-Schnittstelle für den Internetzugriff konfiguriert wird.

1 Starten Sie Ihren Internetbrowser. Geben Sie als

Adresse 192.168.1.1 (die Standard IP-Adresse der

ZyWALL) ein.

Wenn das Loginfenster nicht angezeigt wird, lesen

Sie in Abschnitt 10.1 nach, wie Sie die IP-Adresse

Ihres Computers einstellen können.

2 Klicken Sie auf Login (Einloggen) (das

Standardpasswort 1234 ist bereits vorgegeben).

3 Ändern Sie das Passwort, indem Sie ein neues

Passwort eingeben und auf Apply (Übernehmen)

klicken.

4 Klicken Sie auf Apply (Übernehmen), um das

Standarddigitalzertifikat der ZyWALL zu ersetzen.

ページが読み込まれています...

ZyXEL Communications Network Card 5 ユーザーマニュアル

このマニュアルも適しています

ZyXEL Communications Network Card 5 ユーザーマニュアル

他の言語で

関連論文

その他のドキュメント