Supplement for the Basic Operation manual
MIMAKI ENGINEERING CO., LTD.
D201593
II
II
This is the additional explanation of the update functions on the UJF-605C,
UJF-605CII operation manual. Please read and fully understand this manual
before using the device.
This manual correspond to the models as firmware version 2.50 or later (UJF-6005C),
firmware version 1.00 or later (UJF-6005CII).When turning on the power, you
can confirm the firmware version.To confirm the firmware version refer to
“Switching on the power supply” (Operation manual: chapter 2).
Following function has added to “Setup functions”.
P4-5
Additional Function
P4-6
[UV Scan Add]
In the area where the drawing has just completed, sometimes the UV ink is not
hardened due to insufficient UV irradiation. In this case, a setting is made for per-
forming the scanning while irradiating UV in the vicinity of drawing completion.
UV SCAN ADD : 0-9 (No scanning at 0)
Function names Summary
Set up
UV SCAN ADD Performs UV irradiation near the completion of drawing.
Operation Manual Chapter 4
Following function has added.
P5-29
P5-33
Prevent the nozzle clogging of spot color [SP.REFRESH]
To prevent the head nozzle clog, this unit performs refresh while printer is turned on. However
the characteristic of white ink is different from other inks, therefore nozzle out occurs even
performing the refresh. In this case change the head refresh operation, where white ink is
installed, so as to suitable for the white ink. This will prevent the nozzle out.
STEPS:
1. Select the [SP.REFRESH] from the [MAIN-
TENANCE]. ( P.5-2)
2. Press the [ENTER] key.
• All the initial value of SP. REFRESH is set to OFF.
Indicated as “*”.
3. Select a head to spot color refresh by
pressing the [ ] and [ ] keys.
4. Select ON or OFF of spot color refresh
execution by pressing the [ ] and [ ] keys.
• Set the head where install the white ink to ON.
Indication shows “W”.
• In the case if white color is installed onto spot color,
due to the ink set change, set the head to ON.
Indication shows “S”.
5. Press the [ENTER] key to make effective the
setting.
Operation Manual Chapter 5
MAINTENANCE
SP.REFRESH <ent>
SPECIAL REFRESH
COLOR
: ∗ ∗ ∗ ∗ ∗ ∗ W S
SPECIAL REFRESH
COLOR : ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗
SPECIAL REFRESH
COLOR
: ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗
MAINTENANCE
SP.REFRESH <ent>
Following function has added to firmware ver.1.30 or later.
P5-34
Change the print quality [PRINT MODE]
To print by HIGH mode, change the setting as follows.
STEPS:
1. Select the [PRINT MODE] from the [MAIN-
TENANCE]. ( P.5-2)
2. Press the [ENTER] key.
• All the initial value of QUALITY is set to NORMAL.
3. Select QUALITY by pressing the [ ] and [ ]
keys.
NORMAL : Set to normal UJF-605CII setting for both
print speed and quality.
HIGH : Decrease the printing speed, but com-
pared with “NORMAL”, print quality is
higher.
4. Press the [ENTER] key.
5. Press the [END] key twice, and the device
returns to the LOCAL mode.
Operation Manual Chapter 5
MAINTENANCE
PRINT MODE <ent>
MAINTENANCE
PRINT MODE <ent>
PRINT MODE
QUALITY : NORMAL
PRINT MODE
QUALITY : HIGH
<<LOCAL>>
D201593-1.20-09052007
©MIMAKI ENGINEERING CO., LTD IT
/