Gee Bee Model Z 40
WINGSPAN: 1432mm
THE FINEST RADIO CONTROL MODELS
R
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
No.11050
REQUIRED FOR OPERATION
BEFORE YOU BEGIN
ASSEMBLY
SPARE PARTS
OPERATING YOUR MODEL SAFELY
SAFETY PRECAUTIONS
This radio control model is not a toy!
First-time builders should seek the advice of experienced modellers
before commencing assembly and if they do not fully understand
any part of the construction.
Assemble this kit only in places out of children’s reach!
Take care before operating this model.
You are responsible for this model’s assembly and safe operation!
Always keep this instruction manual ready at hand for quick
reference, even after completing the assembly.
For Intermediate
&
Advanced flyers.
INSTRUCTION MANUAL
2
3
3~15
15
14 / 16
RADIO CONTROLLED ENGINE POWERED SCALE AIRCRAFT
KYOSHO SUPER QUALITY SERIES
Before commencing assembly, please read these instructions thoroughly.
©2000 KYOSHO
INDEX
Sharp Hobby Knife
Phillips Screwdriver (L, M, S)
Needle Nose Pliers
Awl
Scissors
2
Wire Cutters
REQUIRED FOR OPERATION (Purchase separately!)
TOOLS REQUIRED (Purchase separately!)
1
A minimum 4 channel radio control
system for aircraft
3 12
12 AA-size batteries,
either dry cell or NiCd.
Read instruction manual supplied with radio control system thoroughly before use.
AAAA
AAAA
AAAA
2
Model Aircraft Engine
Muffler
Muffler Adapter
Engine and Muffler
Glow Plug
3
2
Extension Lead x 2
(400mm)
1
Y- Harness x 1
Purchase a propeller that
will suit your engine.
Propeller
CAUTION: For details concerning the equipment listed below
(size, maker, etc.), check with your hobby shop.
CAUTION
:Only use radio control systems designed for
aircraft.
2 46
4 52 ~ 53
2 Stroke .46
4 Stroke .52 ~ .53
Propeller
4
Fuel Tube
Shock Protecting Foam
x5
This model will require a minimum 4 channel radio control
(with 5 standard servos) for aircraft.
One-touch Plug Heater Set
Required for engine starting:
Fuel Bottle
Plug Wrench
5
Model Glow Fuel.
MO
DEL
EN
G
INE
FUEL
6
SILICONE
Epoxy A
Epoxy B
Instant Glue
(30 )
Epoxy Glue (30 minutes type)
Silicone Glue
Glue
WARNING: Never use petrol/
gasoline with glow
engines.
Engine Starter
12V
12V Battery (for starter)
Other equipment for enhancing aircraft operation & performance
Fuel Filter
7
Spinner Nut
3
1
1
Read through the manual before you begin, so you will have an overall idea of what to do.
BEFORE YOU BEGIN
Check all parts. If you find any defective or missing parts, contact your local dealer or Kyosho Distributor.
2
3
Symbols used throughout this instruction manual comprise the following :
Apply epoxy glue.
Assemble left and right sides
the same way.
Must be purchased separately!
2mm
Drill holes with the specified
diameter (here: 2mm).
Cut off shaded portion.
2mm
Cut off excess.
Apply instant glue
(CA glue, super glue).
Ensure smooth non-binding
movement while assembling.
Do not overlook this
symbol!
low setting
Using an iron covered with a cloth,
start at low setting. Raise the
temperature if it is necessary.
However, too high temperature may
damage the film.
with cover (cloth)
The pre-covered film on ARF kits may wrin-kle due to
variations of temperature. Smooth out as explained
here.
Pay close attention here!
Warning!
Main Wing
Secure aileron hinges with instant glue,
being careful not to glue the wing and
aileron together.
2
3
Assemble left and right sides
the same way.
Cut off shaded portion.
Main Wing (Underside)
Main Wing (Underside)
Servo extension code.(400mm over)
400mm
Fix with tape.
Drill holes with the specified
diameter (here: 2mm).
2mm
Must be purchased separately!
Apply epoxy glue.
2mm
Pay close attention here!
2 x 30mm
Screw
4
Included with the radio set.
Aileron Servo
TP Screw
8
2 x 8mm
TP
2x30mm
2mm
1.5mm
2 x 8mm
Cut only a film.
Cut only a film.
4
5
6
Main Wing
Main Wing (Underside)
Assemble left and right sides
the same way.
Cut off shaded portion.
Apply epoxy glue.
Securely glue together.If coming off
during flights, you lose control of your aircraft
which leads to accidents!
Warning!
Securely glue together.If coming off
during flights, you lose control of your aircraft
which leads to accidents!
Warning!
Do not overlook this symbol!
Warning!
Front
4
Main Wing (Underside)
Cut only a film.
5
7
8
Assemble left and right sides
the same way.
Apply silicone sealant.
Main Landing Gear
Main Landing Gear
4
4.2mm
3 x 4mm
Set Screw
4
Stopper
Stopper
4.2mm
3 x 4mm
8
TP Screw
2.6 x 12mm
2.6 x 12mm
2 x 8mm
2 x 8mm
2 x 8mm
TP Screw
8
2 x 8mm
TP
TP Screw
6
2 x 8mm
TP
Cut off shaded portion.
Drill holes with the specified
diameter (here: 2mm).
2mm
2mm
4.1mm
1.5mm
Cut only a film.
1.5mm
1.5mm
2mm
NOTICE : Remove Wheel Pants
Guide (Refer the illustration.)
before flight.
6
2mm
Drill holes with the specified
diameter (here: 2mm).
2mm
Do not overlook this symbol!
Warning!
Cut off shaded portion.
9
Main Wing & Fuselage
10
Horizontal Tail
Screw
2
Washer
4 x 35mm
4mm
2
2
4mm
Blind Nut
4 x35mm
54mm
16mm
4mm
Screw
Washer
4 x 35mm
4mm
4mm
Blind Nut
4.1mm
5.1mm
Apply silicon sealant or thin sponge sheet
to be stable.
Apply epoxy glue.
A=A'
B=B'
C=C'
A
A'
B
B'
C C'
Cut away only the film.
Pay close attention here!
Apply silicone sealant.
7
11
2mm
Drill holes with the specified
diameter (here: 2mm).
2mm
Apply epoxy glue.
Do not overlook this symbol!
Warning!
Horizontal Tail Elevator
12
Vertical Tail Rudder
Cut off shaded portion.
Pay close attention here!
Bend the wire.
(approx.15mm)
3mm
2.5
mm
Apply instant glue (CA glue, super glue).
Warning!
Warning!
Secure aileron hinges with instant glue,
being careful not to glue the wing and
aileron together.
Secure aileron hinges with instant glue,
being careful not to glue the wing and
aileron together.
3mm
1
Stopper
2.2mm
3 x 4mm
Set Screw
1
2.2mm
8
14
Align the mark on both mounts
with the mark on the fuselage.
4
4mm
Blind Nut
4 x 20mm
Screw
4
Engine Mount
5mm
For 2 stroke engine
A
A
2
A
2
4
4mm
Blind Nut
4 x 20mm
Screw
4
13
Engine Mount
Blind Nut
4mm
4 x 20mm
2mm
Drill holes with the specified
diameter (here: 2mm).
2mm
Apply epoxy glue.
Cut off shaded portion.
Pay close attention here!
For 4 stroke engine
Align the mark on both mounts
with the mark on the fuselage.
5mm
A
2
A
2
A
Blind Nut
4mm
4 x 20mm
9
15
16
2mm
Drill holes with the specified
diameter (here: 2mm).
2mm
Pay close attention here!
For 4 stroke engine
3.1
mm
3 x 25mm
Spring Washer
3mm
Washer
Nut
3mm
3mm
3x25mm
120mm
4
4
4
4
3 x 25mm
Screw
3mm
Nut
3mm
Washer
3mm
Spring Washer
3mm
Spring Washer
Washer
Nut
10
1
3 x 35mm TP
TP Screw
Bend as shown
here.
Completed
12mm
5mm
After confirming the position (see front view
of fuel tank), insert and tighten the screw.
3 x 35mm
Fix with silicon sealant.
Engine
Fuel Tank
Must be purchased separately!
2mm
Drill holes with the specified
diameter (here: 2mm).
2mm
Must be purchased separately!
Apply epoxy glue.
120mm
3 x 25mm
3.1
mm
3mm
Spring Washer
Use a muffler extension adapter.
(purchase separately)
Depends on the position of the throttle arm.
4mm
3 x 4mm
Set Screw
1
2mm
Washer
Nut
Linkage Stopper
1
1
1
2mm
PP
PP Pipe
1.5mm
Rod
2mm
Washer
Nut
2mm
3 x 4mm
4
4
4
4
3mm
Nut
3mm
Washer
3 x 25mm
Screw
3mm
Spring Washer
17
For 2 stroke engine
Engine
18
Spring Washer
3mm
Washer
Nut
3mm
3mm
3x25mm
Washer
Nut
Throttle Rod
Linkage Stopper
11
19
2mm
Drill holes with the specified
diameter (here: 2mm).
2mm
Must be purchased separately!
Cut off shaded portion.
Apply epoxy glue.
Pay close attention here!
Fuselage
20
Cowling
For 4 stroke engine
For 2 stroke engine
For 4 stroke engine
4
TP Screw
TP
2.6 x 12mm
4
TP Screw
TP
2 x 8mm
2.6 x 12mm
Paint.
Dummy Radial Engine
2mm
1.5mm
2 x 8mm
Align with the center
line on the fuselage.
5 7mm
12
13
21
22
23
2mm
Drill holes with the specified
diameter (here: 2mm).
2mm
Must be purchased separately!
Linkage Rod
Adjustable rod
Heat-shrink tube
Be careful not to scorch the
heat-shrink tube!
Beware of the flame!
Rod
2mm
Cut off shaded portion.
Pay close attention here!
Apply instant glue (CA glue, super glue).
Vertical / Horizontal Tail
Throttle Servo
Rudder Servo
Elevator Servo
Throttle Servo
Servo
3 x 4mm
Set Screw
1
2mm
Washer
Nut
Linkage Stopper
1
1
1
2mm
Included with the radio set.
Screw
4
2 x 18mm
Linkage Stopper
2mm
Washer
2mm
Nut
3 x 4mm
Included with the
radio set.
2x18mm
2mm
2x18mm
2mm
Do not overlook this symbol!
Warning!
Must be purchased separately!
Cut off shaded portion.
Apply epoxy glue.
Pay close attention here!
24
25
26
Canopy
/
Receiver / Battery
Secure foam padding with
rubber bands or tape as required.
Carefully install the receiver and battery pack to
ensure that they will not move during flight.
Foam Pad
Move the location of the receiver and battery pack
as needed to obtain the specified CG.
RUDDER
AILERON
Never fly before checking the CGÕs required position.
You must keep a balance by an engine to use.
You must keep a balance by an engine to use.
Adjust the travel of each control surface to the
values in the diagrams. These values fit general flight
capabilities. Readjust according to your requirements
and flight experience.
ELEVATOR
10 12mm
10 12mm
25 30mm
16 18mm
16 18mm
25 30mm
Control Surface Movement
Paint.
2 46 4 52~53
This model aircraft is designed for Intermediate to Experienced fliers. Beginners should seek advice for pre-flight adjustments and assembly
from more experienced fliers. Be aware that flying a badly assembled or badly adjusted aircraft is very dangerous!
At the start, first-time fliers should always be assisted by an experienced flier and NEVER fly alone!
This model aircraft is designed to be powered by either a 2 stroke .46 size engine or a 4 stroke .52 ~ .53 size engine. Installing a more
powerful engine than specified or flying this model dangerously could lead to serious injury and/or damage to property.
Warning!
14
15
PARTS
No. Part Names Quantity
11050-01
Cowling (FRP)
1 4500 200 200
11050-02
Canopy
1
2
11050-03
1200
2000
Main Landing Gear
No. Part Names Quantity
11050-04
Wheel Pants (FRP)
2 7000
11050-05
Decal
1
11050-06
2000
1600
Dummy Radial Engine
1
27
Decal
14
9
2 2
10
9
99
1
5
16
10
7
15
12
2
3
1
13
6
8
4
5
:FOR JAPANESE MARKET ONLY.
OPTIONAL PARTS
Nylon Propeller
750
90412-06
No. Part Names
200
Long Spinner Nut (UNF5/16-28
800
90427-09
No. Part Names
200
:FOR JAPANESE MARKET ONLY.
00
0 0 2 1 0 4 4 7 2 7 1
1 6 8 0
0 0 2 1 0 4
4 7 2 7 1
1 6 8 0
1,400
200
80
1,680
(1)
(2)
(2)
(3)
(4)
(1)
11050
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
他の言語で
- English: Kyosho GeeBee Model Z 40 User manual
関連論文
-
Kyosho PT-17 STEARMAN 40 ユーザーマニュアル
-
-
-
-
-
-
-
-
-