Toolots KC-508は、タイヤの脱着を簡単にするために設計された、高品質のセミオートマチックタイヤチェンジャーです。その機能には以下が含まれます。
- ビードブレーカー: この機能により、タイヤビードをリムから安全かつ簡単に壊すことができます。
- クランプジョー: これらのジョーは、タイヤを所定の位置に保持し、回転中に滑るのを防ぎます。
- ターンテーブル: このターンテーブルは、タイヤを回転させて、作業者がタイヤのすべての部分にアクセスできるようにします。
- インフレーションシステム: このシステムは、タイヤを適切な空気圧に膨らませるのに役立ちます。
Toolots KC-508は、自動車、トラック、オートバイなど、さまざまな種類のタイヤに使用できます。また、ガレージや自動車修理工場での使用に最適です。
Toolots KC-508は、
Toolots KC-508は、タイヤの脱着を簡単にするために設計された、高品質のセミオートマチックタイヤチェンジャーです。その機能には以下が含まれます。
- ビードブレーカー: この機能により、タイヤビードをリムから安全かつ簡単に壊すことができます。
- クランプジョー: これらのジョーは、タイヤを所定の位置に保持し、回転中に滑るのを防ぎます。
- ターンテーブル: このターンテーブルは、タイヤを回転させて、作業者がタイヤのすべての部分にアクセスできるようにします。
- インフレーションシステム: このシステムは、タイヤを適切な空気圧に膨らませるのに役立ちます。
Toolots KC-508は、自動車、トラック、オートバイなど、さまざまな種類のタイヤに使用できます。また、ガレージや自動車修理工場での使用に最適です。
Toolots KC-508は、
Semi-automatic tyre changer operation manual
1
Tyre Changer
Operating Instruction
Semi-automatic tyre changer operation manual
2
Preface：
Thank you for buying our semi-automatic tyre changer. It is the best quality .In order to proper
operation and extended the lifetime, pls read the instruction for each operation section carefully.
The data of semi- automatic tyre changer:
Provide the “complete product code” and the” model of semi-automatic tyre changer”, so that we
can provide you the technical services and required parts betterly .At the same time, easy to operate
the machine as technical parameters .If the data in the specification is inconsistent with the label,
please refer to the label.
This manual is an indispensable part for machine operation before using the machine, you
should read each part of the manual carefully, The operation safety and maintenance parts are
necessity.
Save this manual for future using!
Semi-automatic tyre changer operation manual
3
1．Description of equipment
G ) clamp jaw P) column U) pedal control bead breaker
I ) working head Q) air connection head V) pedal control clamp
L) inflation inlet R) bead breaker Z) pedal control turntable
M) operation arm S) rubber pad Y) turntable
N) horizontal swing arm T) crowbar K) locking handle
Pic.1
Semi-automatic tyre changer operation manual
4
Danger warning sign
Pic. 2
Semi-automatic tyre changer operation manual
5
2、General description
2.1 Operation instruction
●The semi-automatic tyre changer is designed to facilitate to mount and demount the tires which the
rim sizes is from 9 "to 25" and the maximum diameter of 1,070 mm.
Operation against instruction is prohibited.
● The manufacturer shall not be liable for damage resulting from non-compliance with the
instructions.
2.2 Safety operation rule
The semi-automatic tyre changer must be operated by trained personnel.
●The manufacturer shall not be liable for any damage caused by modification of the machine without
the manufacturer's approval.
●Manufacturers will immediately discontinue their safety commitments if the user
breaches safety rules and causes damage of the machine's safety devices.
●If there is any damage to the safety warning sign during the whole process, the
customer can contact the manufacturer according to the icon on page 3 to replace the
damaging icon as soon as possible.
3、Transport
●The semi-automatic tyre changer must be transported with the original packaging. Place
as indicated on the packing box.
●Move the packed machine by a forklift truck with corresponding
lifting capacity. Refer to figure 3 for the forklift insertion direction
Pic.3
Semi-automatic tyre changer operation manual
6
4、Open package operation
●Open protective boxes and plastic bags.
●Refer to figure 1 to check whether the machine surface is intact and the parts are missing
and damaging.
●If any problem is found, please do not use the machine and contact the supplier immediately.
5、Installation instruction
5.1 Space required
The installation position of the machine must meet the standard of safe working.
●The semi-automatic tyre changer should be placed near the main power supply and
compressed air system.
●The minimum space of the installation position shall not be lower than the space that be
shown in figure 4 and figure 4/A to ensure normal operation without any restriction.
●If the machine is installed outdoors, a protective shelter must be built.
The semi-automatic tyre changer is prohibited to use in explosive gas
Pic. 4 Pic. 4/A
Semi-automatic tyre changer operation manual
7
5．2 Installation of components
● Unscrew the fixed screws on the packing wooden pallet and place the semi-automatic tyre changer
on the ground.
● As shown in figure 5/a, unscrew 6 screws from the box body and install the vertical column at the
designated position . Tighten the screws.
Note: for semi-automatic tyre changer, the following three operations are not required:
●Remove pin shaft, nut, washer and adjusting spacer from horizontal swing arm.
●Apply lube to the support on horizontal swing arm. Insert adjustment spacer to prevent friction
of horizontal swing arm
●Place the horizontal swing arm on the vertical column, insert the pin shaft and tighten it with the
nut and washer.
Note: before connecting all power , check that the installation status of the machine is consistent with
the installation requirements of the machine.
● Connect the machine to the compressed air system.(as shown in figure 5/c)
● Step on the pedal to control the bead breaker and the piston rod of cylinder can be extended.(as
shown in figure 5/d)
● Install the tire pressure device as shown in figure 5/e.
insert tire pressure device to bearing, insert the screw hole, not to tighten with the nut or the
wrench.
The piston rod of cylinder through the rotation hole in the pressure device.
Screw on the nut, but don't tighten it.
place the spring at the specified point
.
● Tighten the screws on the tire pressure device as shown in figure 5/f.
● Tighten the nut on the piston rod of the cylinder as shown in figure 5/g.
Semi-automatic tyre changer operation manual
8
Pic.5
Pic.5/a Pic.5/b
Pic.5/c Pic.5/d
Pic. 5/f
Pic. 5/e
Pic.5/g
Semi-automatic tyre changer operation manual
9
5.3 commissioning
Before the machine is turned on, make sure the user's voltage and air pressure are
consistent with the machine's requirements.
When the operating voltage of the machine needs to be changed, the terminal board can be adjusted
properly.(refer to part 14 circuit diagram)
The electrical system must be operated by a professional.
●The compressed air system is connected to the machine by a pipe joint (Q) on the
oil-water seperator beside of the box .
●When connecting the circuit of the machine, the circuit must be equipped with safety fuse,
grounding wire and must be installed with 30mA automatic circuit breaker.
Note: the power plug of the tyre changer shall be prepared by the customer. The rated
current of the power plug shall not be lower than 16A, at the same time meet the voltage
of the machine.
5.4 Debugging machine
●When the pedal (Z) is stepped on, the turntable (Y)
should turn clockwise.
●When the pedal is raised, the turntable should turn
counterclockwise.
Note: if the turntable is opposite to the specified rotation
direction, switch the two wires of the three-phase plug.
●When the pedal (U) is stepped on, the pressure tyre
device (R) will start ; When the pedal is released, the
tire pressure device returns to its original position.
●When the pedal (V) is stepped on, four clamp jaws will open (G); Pic.6
step on the pedal again and the clamp jaws are closed.
Semi-automatic tyre changer operation manual
10
Adjust the jaw position of turntable
●The clamps of tyre changer have been adjusted to the central position before leave
factory, the clamp rim from outside size is from 9 "to 21".inside size is from 13 "to
25".
●If you want to demount the larger or smaller rim, you can adjust the position of the four
clamps, as shown in figure 6/b.
Adjustment range:
clamp rim outside size is from the smallest 9 "-19" to the largest 11 "-21".
clamp rim inside size is from the smallest 13 "-23" to the largest 14 "-25".
The operation is as follows:
use universal wrench unscrew the screw (1)
mobile clamp jaw (2) and slider (3), the position corresponding to one of the screw hole of
the lock size
tighten screw, universal wrench torque must be 72 N.m.
Note: the corresponding positions of the four clamps should be ensured when the above adjustment is
carried out.
Pic.6/b
Rim clamp from outside 9”-19”/
Rim clamp from inside 13”-23”
Rim clamp from outside 9”-19”/
Rim clamp from inside 13”-23”
Rim clamp from outside 10”-20”/
Rim clamp from inside 13”-24”
Rim clamp from outside 11”-21”/
Rim clamp from inside 14”-25”
Semi-automatic tyre changer operation manual
11
6、Operation
Please read the instruction manual carefully and note before operating the machine.
The operation of semi-automatic tyre changer is divided into the following three parts:
breaking the bead /demount tire /mount tire
Matters need attention:
● More and more motorcycle rims are made from special materials such as aluminum magnesium
alloys and carbon fiber, In order to lock into this kind of rim , must use special repair tool of the
motorcycle tire.
● To avoid damage, The maximum pressure limit of working plate is 5bar.
6.1 Breaking the bead
●Check the tire to see if it has emptied the gas. If not, empty the gas
● Please close the clamp jaws of the turntable.
Do not place your hand on the side wall of the tire during operation of the turntable.
The clamp may be pressed to your hand when it is open
● Lean against the tire on the rubber pad (S) on the right side of the automatic tyre changer.
●Press the bead breaker closer to the edge of the rim 1cm (figure 8).It should be noted that the bead
breaker should be placed on the tire instead of the rim.
● Step on the pedal (U) and the pressure device is started. Release the pedal when the bead breaker
completes the operation or the rim is off.
●Gently rotate the tire and repeat in the rest of the tire until the flange is completely off the rim.
Repeat on the other side of the tire.
Discharge all air from the tire and remove the balance lead from the tire.
You have to be very careful when you are operating bead breaker. When the pedal is
operated, the breaker arm will swing rapidly and forcefully, and any object within the
movable range of the breaker arm is at risk of being crushed.
Semi-automatic tyre changer operation manual
12
Pic. 7 Pic. 8
6．2 Demount tire
Before any operation, check to see if the tire is out of air. And ensure that
the balance lead has been removed from the rim.。
Apply special lubrication to the rim。
Failure to apply lubricant may result in wheel rim damage。
Do not put your hand under the tire when you lock the rim.
To properly lock the tires, place tire in the center of the turntable.
Clamp the rim outside between 10 and 20 inches
● Step the pedal (V) to the central position and locate the clamp (Y) according to the
reference scale of the turntable.
● Place the tire on the clamp so that the rim is near the lowest part of the clamp and step
on the pedal (V) to the bottom.
Clamp the rim inside between 13 and 24 inches
● Make the clamp (G) closed completely.
● Place the tire on the clamps and step the pedal V to clamp the rim。
Make sure that the rim is firmly fixed to the clamps。
Don’t put your hands on the wheel: if you put your hands between
rim and mounting head, it may getting hurt when column return to its
original position.。
●Lower the operating arm (M) until the dismounting head is supported on the rim edge
and locked with the locking handle (K).In the process, the operating arm is locked in a
fixed position in the vertical direction, and the working head is moved to 2mm above
the rim.
Semi-automatic tyre changer operation manual
13
Note：Once the operating arm is locked in the vertical direction, the working head must
be manually removed from the rim (approximately 2mm) with the manual wheel
on the left side of the horizontal swing arm.
●With the crowbar T interested between the bead and the front section of mounting
head I, move the tire bead over the mounting head I with crowbar T(see pic.10).
Note：In order to avoid damaging the inner tube, if there is one, it should be 10cm to the
right of the mounting head I about the above operation.
●While the crowbar in this position, rotate the turntable Y clockwise by pressing down
on pedal Z until the tire is completely separated from the wheel rim.
Keep your hands and body as far away as possible from the moving parts
when operating the machine, to avoid getting hurt.
Necklaces, bracelets, loose-fitting clothing, or external items can cause
personal injury to the operator if they are close to the rotating parts.
●Remove the inner tube if there is one. Repeat the same operation for the other bead.
Pic.9 Pic.10
6．3 tire mounting
Note：To avoid explossion in inflating, it is important to check the tire and rim.
Before mounting the tire, pay attention to the following points：
●Don’t mount the tire if the outside of tire is damaged.
●Check whether the rim is dented or deformed. In particular, there will be
small cracks in the rims of alloy wheels, which cannot be seen with naked eyes,
that will damage the durability of wheel, so there will also be risks in inflating
process.
●Make sure that the wheel rim and tire are of the same size. If you cann’t make
sure of it, don’t mount the tire.
Semi-automatic tyre changer operation manual
14
●Lubricate the tire beads with special grease in order to avoid damaging them and to
facilitate the mounting operations.
Don’t put your hands between tire and clamps in operating clamps, avoiding
hands injury
Note: When working with the rims of the same size, it is not necessary always to
lock and unlock the mounting bar, just move away and return to its original
position about horizontal operating arm.
Don’t put your hands on the wheel: if you put your hands between rim and
mounting head, it may getting hurt when operating arm return to its original
position.
●Move the tire so that the bead passes below the front section of the mounting head
is brought up against the edge of the rear section of the mounting head itself.
●Keep the tire bead pursed down into the wheel rim channel with your hands. Step
pedal M to rotate the turntable clockwise. Continue until you have covered the entire
circumference of the wheel rim.
Keep your hands and body as far as away from the operating arm when
rotating the turntable, avoiding body injury.。
●Insert the inner tube, if there is one. Repeat the above operation for the other side of
bead.
Note ：Turntable is always rotating clockwise during mounting and demounting
process, unless the machine is something wrong or operating mistakenly, it may rotate
anticlockwise.
Pic.11 Pic. 12
7．Inflating
You have to inflate the tire carefully, following below instructions strictly. Pls
note there is no protection device on designing of the tire changer for the safety
of the operator on the machine or surrounded machine if the tire explode
suddenly.。
Semi-automatic tyre changer operation manual
15
●A burst of tire can cause serious injury or even death of the
operator。
●Check carefully that the wheel rim and the tire are of the same size。
●Check the state of wear of the tire and there is no defects before
beginning the inflation stage。
●Inflate the tire with brief jets of air, checking the pressure frequently。
●All our tire changers are limited to a maximum inflating pressure of
3.5 bar in any case never exceed the pressure recommended by the
manufacturer。
●keep your hands and body as far as possible from the tire
in inflation stage。
7．1 Inflating tire with nozzle
Standard semi-automatic tire changer is equipped with
pressure nozzle to inflate a tire。
Follow below instructions to inflate a tire：
●Connect the nozzle fitting to the tire valve。
●Check the wheel rim and the tire are of the same size。
●Check the wheel flange and rim are with enough lubrication.
●Press the nozzle trigger, in this stage, control the inflating pressure, until the tire fits
to the rim completely.
●Continue to inflate the tire and check the inflating pressure frequently, never to
exceed the pressure indicated by the manufacturer。
Danger of burst：
●Never to exceed the pressure indicated by the manufacturer：3.5bar
●Remove the tire from the turntable, if you need more inflating
pressure, place the tire in special protection cage to continue the inflation
operation。
●Never to exceed the maximum inflation pressure。
●Keep your hands and body as far as away from the tire。
●Only professionals are allowed to use the machine. Other people are not allowed to
use or approach the machine during the inflation stage。
Pic.13
Semi-automatic tyre changer operation manual
16
8．Relocate
Forklifts are needed to move semi-automatic tire changer。
●Disconnect the electric power supply and compressed air system。
●Insert the crowbar on one side bottom of the tire changer, get the machine off the
ground, and then insert the fork, lifting it up.
●Place the tire changer in new position。
Note: Location of the new place must comply with national safety regulations.
9．Storage
If the tire changer need to be stored for some time，pls follow below instructions:
Disconnect all energy supplies and lubricate the slide of the clamps on the turntable to
prevent oxidation。
10．Scrap
Make sure all energy supplies are disconnected when deciding to scrap the equipment。
●All nonferrous metals and nonmetals shall be disposed of as scrap in accordance with
relevant laws and regulations。
●Process the oil inside the machine at the place specified by applicable law。
●Discard the remaining steel。
11、Maintenance
11.1 Warning
Untrained people is not allowed to carry out maintenance work。
●Regular maintenance as described in the instructions for correct operation and long
lifetime of the tire changer。
●If maintenance is not carried out regularly, the operation and reliability of the machine
may be compromised, thus placing the operator and anyone else in the vicinity at risk。
Before carrying out any maintenance work, disconnect the electric and
pneumatic supplies.
Moreover, if it is necessary to break the bead load less 3-4 times in order
to let the air in pressure go out the circuit。
●Damaged parts must be replaced exclusively by expert personnel use the
manufacturer’s spare parts。
●It is forbidden by national safety regulation to disassemble and replace safety
devices(safety valves and regulating valves)。
Semi-automatic tyre changer operation manual
17
11.2 maintenance
● Clean the turntable once a week with diesel fuel so as to prevent the formation of
dirt, and grease the clamp sliding guides。
● Perform the following maintenance work once a month：
Control the oil level of oil-water separator. If the level is low, screw off the oil
cup F before adding. Use only oils specified by ISO HG with viscosity ISO
VG32. Such as: ESSO Febis K32,MOBIL Vacouline 1405,KLUBER32(Pic.15)
Step pedal bead breaker 3-4 times, checking if some oil filled in oil cup F. If not,
adjusting screw D.(Pic.15)
Note: After the first 20 days of work, retighten the clamp tightening screws and
screws on turntable slides。（Pic.16）
Note：In the event of a loss of power, check that the drive belt is tight or not as follow：
Disconnect power supply before operation。
●Remove the left side body panel of tire changer, unscrewing the four fixing screws。
●Tighten the drive belt by means of the special adjusting screw X on the motor support。
(Pic.17)
Note：If the working head is not locked or cannot be stopped 2mm above the rim, the
locking plate of the operating arm shall be adjusted as shown.(Pic. 18)。
Note ：For cleaning or replacing the silencer of opening/closing clamps(G),proceed as
follows(see Pic.19)：
1）Remove the left side panel of the machine body by unscrewing the four fixing screws。
2）Unscrew the silencer put on pedal system V, on the clamp G opening/closing pedal.
3）Clean by a jet of compressed air, or if damaged, replace by the same spare parts。
Note：For cleaning or replacing the silencer of bead breaker R, see pic. 20,
and proceed as shown on previous point 1&3.
In particular, the manufacturer shall not be liable for any damage caused by
users using parts of other manufacturers or damage by disassembly
and damage of safety devices.。
Semi-automatic tyre changer operation manual
18
Pic.15 Pic.16 Pic.17
Pic.18 Pic.19 Pic.20
12、Trouble shooting
trouble
cause
troubleshooting
Turntable rotates only in one direction
universal switch is damaged
universal switch
Turntable doesn`t rotate
1、Belt is damage
2、universal switch is damage
3、motor trouble
1、replace the belt
2、replace the universal switch
3、replace motor
Turntable doesn`t work
Belt loose
Adjust belt tension
clamp open/close slowly
1、Silencer trouble
Clean or replace
turntable doesn`t lock the rim correctly
1、Clamp is damaged
2、Cylinder of turntable is damaged
1、Replace clamp
2、Replace the sealing ring of cylinder
The working head touch the rim when
operation
1、Locking place position is incorrect
or damaged
2、Turntable locking screw loose
1、Adjust or replace locking plate
2、Tighten screw
Pedal should not be located in working
position
Return spring damage
Replace the return spring
Bead breaker
operation difficult
1、Silencer trouble
2、Cylinder sealing ring of bead
breaker is damaged
1、Clean or replace the silencer
2、replace the sealing ring
Semi-automatic tyre changer operation manual
19
13. Technical data
Power Supply Voltage
110 V, 60 Hz, 1 Ph
Motor
1.5 HP ( 1.1 kW ）
Working Pressure
116 PSI - 145 PSI ( 8 bar - 10 bar )
Bead Breaker Force
Pneumatic 5500 lbs
Drive System Type
Electric / Pneumatic
Table Clamping
Dual Pneumatic Cylinders
Bead Breaking System
Adjustable Pneumatic Blade
External Rim Clamping
12" - 22" ( 305 mm – 559 mm )
Internal Rim Clamping
13" - 24" ( 330 mm - 609 mm )
Max. Wheel Width
13" ( 330 mm )
Max. Wheel Diameter
41" ( 1040 mm )
Turntable Rotating Torque
885 ft/lbs
Power Cord Length
78 47/64" ( 2000 mm )
Speed
7 RPM
Turntable Tire Width Capacity (Mounting)
5" - 12" ( 127 mm - 305 mm )
Bead Breaker Tire Width Capacity (Demounting)
1 1/2" - 13" ( 38 mm - 330 mm )
Noise Level
<70 dB
Product Dimensions
L 43.3" x W 55.12" x H 76.18" ( 1100 mm x 1400 mm x 1935 mm )
Product Weight
416.67 lbs ( 189 kg )
Semi-automatic tyre changer operation manual
20
14. Circuit diagram and pneumatic system diagram
Sensor of the
commutator
motor
0.75Kw
Motor
230v-1P
Reset
switch
Plugs and sockets
User-owned
Motor connection
motor
Reset
switch
User-owned
blue red white
black
blue red white
black
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
Toolots KC-508は、タイヤの脱着を簡単にするために設計された、高品質のセミオートマチックタイヤチェンジャーです。その機能には以下が含まれます。
- ビードブレーカー: この機能により、タイヤビードをリムから安全かつ簡単に壊すことができます。
- クランプジョー: これらのジョーは、タイヤを所定の位置に保持し、回転中に滑るのを防ぎます。
- ターンテーブル: このターンテーブルは、タイヤを回転させて、作業者がタイヤのすべての部分にアクセスできるようにします。
- インフレーションシステム: このシステムは、タイヤを適切な空気圧に膨らませるのに役立ちます。
Toolots KC-508は、自動車、トラック、オートバイなど、さまざまな種類のタイヤに使用できます。また、ガレージや自動車修理工場での使用に最適です。
Toolots KC-508は、
他の言語で
- English: Toolots KC-508 User manual
