INVERTER
FR-E846 dedicated protective cover
<FR-E8PC>
Specifications subject to change without notice
IB(NA)-0600987-A(2307)MEE
1.
2.
Thank you for choosing this Mitsubishi Electric inverter option unit.
This document provides handling information and precautions for use of this product. Incorrect handling might
cause an unexpected fault. Before using this product, always read this document carefully to use this product
correctly.
Please forward this document to the end user.
This product is a protective cover to be installed to a main circuit connector of the FR-E846 inverter (IP67
model) to prevent insertion/removal of the connector during power-on.
3 Installation procedure
The following explains an example of installation to the main circuit connector for motor.
This product can also be installed to the main circuit connector for power supply and the main circuit
connector for option.
When installing this product to all of the three connectors, prepare three sets.
1. Connect a cable to a connector, then lock them.
2. Fit the holes on the FR-E846 dedicated protective cover to the mounting holes, then
tighten the mounting screws. (Tightening torque: 1.65 N·m)
1 Enclosed items 2 Outline dimensions
Check the enclosed items and quantity of each
item.
CAUTION
• Do not apply strong force to the product. Doing so may damage the product.
Enclosed items Quantity
FR-E846 dedicated protective
cover (FR-E8PC) 1
Mounting screw (M4-8) 2
Manual 1
(Unit: mm)
Main circuit
connector for option
Main circuit connector
for motor
Main circuit connector
for power suppl
Mounting holes
for protective cover
Mounting holes for
protective cover
Mounting holes for
protective cover
三菱电机通用变频器
FR-E846 专用保护盖板
<FR-E8PC>
IB(NA)-0600987-A(2307)MEE
非常感谢您选择三菱电机通用变频器选件模块。
本使用手册对使用时的操作、注意事项进行说明。由于错误地使用可能会导致意外的故障，所以应务必在使用
之前熟读本使用手册，以便正确安全地使用本产品。
此外，请将本使用手册交付至使用者。
本产品是保护盖板，通过将本产品安装到 FR-E846(IP67 规格产品 ) 的主电路接口部分，以防止通电时主电路接
口的插拔。
3 安装方法
安装至电机用主电路接口的示例如下所示。
可安装在电源用主电路接口或选件用主电路接口中任意一个。
如果在三个接口上全部安装，则需三套本产品。
1. 电缆连接至接口后，将电缆和接口锁住。
2. 在安装孔处使用安装螺丝紧固 FR-E846 专用保护盖板。
（紧固转矩 1.65N·m）
1随附品 2 外形尺寸图
请确认随附品的内容、数量。
注意
• 请勿对本产品施加过大的力。否则可能造成损坏。
随附品 个数
FR-E846 专用保护盖板 （FR-E8PC） 1
安装螺丝 （M4-8） 2
使用手册 1
˄অս˖PP˅
䘹Ԧ⭘ѫ⭥䐟
᧕ਓ
⭥ᵪ⭘ѫ⭥䐟
᧕ਓ
⭥Ⓚ⭘ѫ⭥䐟
᧕ਓ
؍ᣔⴆᶯ⭘
ᆹ㻵ᆄ
؍ᣔⴆᶯ⭘
ᆹ㻵ᆄ
؍ᣔⴆᶯ⭘
ᆹ㻵ᆄ
MEMO
/