Yongnuo YN-E3-RT ユーザーマニュアル

カテゴリー
カメラが点滅する
タイプ
ユーザーマニュアル
User Manual
YN-E3-RT
Contents
Introduction . . . . . . . . . . . . . . . . . . . . 1
Nomenclature . . . . . . . . . . . . . . . . . . . 2-4
Preparation Before Use . . . . . . . . . . . . . . . 5-6
Wireless Flash Shooting. . . . . . . . . . . . . . . . 7
Wireless Settings . . . . . . . . . . . . . . . . . 8-9
ETTL:Fully Automatic Wireless Flash Shooting . . . . . 10-14
M: Wireless Multiple Flash Shooting with Manual Flash Output. 15-16
MULI: Stroboscopic Flash . . . . . . . . . . . . . . 17
Gr: Shooting with a Different Flash Mode for Each Group . 18-19
Remote Release from a Slave Unit/Linked Shooting . . . 20-21
Transmitter Control from Cameras Menu Screen . . . . 22-23
C.Fn/P.Fn: Setting . . 24-27
Reference . . . . . . . . . . . . . . . . . . . 28-29
Troubleshooting Guide . . . . . . . . . . . . . . 30-31
Specifications . . . . . . . . . . . . . . . . . . 32-33
Read this instruction manual while also referring to the
instruction manuals of your camera and Speedlite.
Before using the transmitter, read this instruction
manual and the instruction manuals of your camera and
Speedlite to familiarize yourself with the operations.
Custom and Personal Functions
Introduction
The YONGNUO Speedlite Transmitter YN-E3-RT is a
transmitter for wireless flash shooting. It can control up to
5 groups (15 units) of Speedlites that have a wireless
multiple flash shooting function using radio transmission.
The transmitter also has dust and water resistance
equivalent to EOS-1D series cameras.
T w o - w a y 2.4G ra d i o c o mmuni c a t i o n , ful l y
compatible with ST-E3-RT/600EX-RT
15 Physical Channels, 1 Auto Channel, Up to 10,000
customizable photographer ID
Transmission Range: 100M
Multi YN-E3-RT can share slave flashes
Display group/charge status of slave flashes
Firmware can be upgraded via USB
High resolution Dot-Matrix LCD, Backlight for LCD/keys
Fast lock mechanism
Built-in AF assist beam emitter, buzzer
Remote shutter release, Linked Shot (Need extra shutter
cable for cameras released before 2012)
Flash Mode: ETTL/M/Multi/GR 4 flash modes
A/B/C/D/E 5 groups
Supports 1st Curtain, 2nd Curtain (Only in M mode),
High speed Sync
Supports ETTL Ratio, Flash Exposure Compensation,
Flash Exposure Lock, Flash Exposure Bracket, Modeling
Flash
9 Custom Funtions
Settings saved automatically
1
The protective flim
can be torn out.
LCD panel
Function button 1
Linked shooting
button
Select/Set button
Select dial
Dust- and water-
resistant adapter
Mounting foot
lock lever
Lock-release
button
ONPower on
LOCKButton/dial lock
(Power on)
OFFPower off
Flash exposure
confirmation lamp
Batter y compartment
cover
<LINK>
Radio transmission
confirmation lamp
Terminal cover
Mounting foot
Locking pin
Contacts
USB upgrade /
Remote release
terminal
terminal
AF assist lamp
:Charge lamp/
Test flash button
Function button 2
Function button4
Function button3
Flash mode button
2
Nomenclature
Manual flash
MManual Flash
Manual flash
output
E-TTLIIAutoflash
FEB
FEC amount
ETTL:E-TTL II/E-TTL
autoflash
Flash exposure
compensation(FEC)
Firing group
Flash ratio
Flash exposure level
Slave flash ready
Custom
Functions
ChChannel
AUTO: Channel
automatic setting
Radio transmission
wireless shooting
Beep
Personal Functions
High-speed sync
Master
FEB sequence
RATIO:Flash ratio
The display will show only the settings currently applied.
The functions displayed above function buttons 1 to 4,
change according to the settings status.
When a button or dial is operated, the LCD panel illuminates.
Manual Flash 2nd
curtain sync
3
Nomenclature
Multi(stroboscopic) flash
Group firing
Linked shooting
MULTI:
Multi flash
Number of flashes
Flash frequency
Gr : Group flash
Flash mode
Firing group
LINKED SHOT:
Linked shooting
SLAVE
MASTER
SLAVE
MASTER
4
Nomenclature
1.Install two AA/LR6 batteries.
1.Open the cover:Slide the cover down as
shown and open the battery compartment
cover.
2.Install two AA batteries: Install two AA
batteries according to the + and - marks,
rechargeable batteries of 1.2V can be used.
3.Close the battery: Close the battery
Compartment cover and slide it up.
Remove the batteries when the product
is not used for long time. Please replace
the both two batteries at the same time.
When < > is displayed, replace the
batteries with new ones.
Preparation Before Use
5
2.Attaching and Detaching the Transmitter
1.Attach the transmitter.
Slip the transmitters mounting foot all the
way into the cameras hot shoe.
2.Secure the transmitter.
On the mounting foot, slide the lock lever to
the right. When the lock lever clicks in place,
it will be locked.
3.Detach the transmitter.
While pressing the lock-release button, slide
the lock lever to the left and detach the
transmitter.
Before attaching or detaching the transmitter, be sure to
turn the transmitter power off.
ØThe LCD panel illuminates.
The charge lamp lights when the
wireless shooting (slave) is ready.
During wireless shooting, press the
transmitter’s charge lamp (test flash
button) to fire a test flash.
About Auto Power Off
To save battery power, the power will turn off automatically
after 5 min. of idle use. To turn on the transmitter again, press
the camera’ s shutter button halfway, or press the test flash
button (charge lamp).
About the Lock Function
By setting the power switch to <LOCK>, you can disable flash’ s
button and dial operations. Use this to prevent the transmitter
function settings from being accidentally changed after you set
them.
If you operate a button or dial, <LOCKED> is displayed on the
LCD panel .
About the LCD Panel Illumination
When a button or dial is operated, the LCD panel illuminates in
greenfor 12 sec. When setting a function, the illumination
continues until the setting is complete.
The transmitter settings are stored even when the
power is turned off.
You can fire a test flash even when the power switch is
set to the <LOCK> position. Also, when a button or dial is
operated, the LCD panel illuminates.
3.Turning on the Power:Set the power switch to <ON>.
Preparation Before Use
6
C
A
B
MASTER
SLAVE
SLAVE
SLAVE
Positioning and Operation Range
(Example of wireless flash shooting)
Transmission distance
Approx. 100 m
Using a transmitter and a Speedlite compatible with radio
transmission wireless shooting makes it easy to shoot with
advanced wireless multiple flash lighting, in the same way as
normal E-TTL II/E-TTL autoflash shooting.
The system is designed so that the settings of the transmitter
attached to the camera (master) are automatically reflected on
the Speedlite that is wirelessly controlled (slave). Therefore, you
do not need to operate the slave unit while shooting.
The basic relative positions and operating range are as shown in
the figure. You can then perform wireless E-TTL II/E-TTL
autoflash shooting just by setting the master unit to <ETTL>.
Wireless Flash Shooting
Before shooting, perform a test flash (p.10) and test
shooting.
The transmission distance may be shorter depending
on the conditions such as the positioning of slave units,
the surrounding environment and weather conditions.
7
Wireless Settings
1.Display < >.
Pres s functio n bu tt on 4 to
displaym < >.
2.Set a channel.
Press function button 1 <CH>.
Turn < > to select AUTO
or a channel from Ch. 1 to 15, and
press the < > button.
3.Set a wireless radio ID.
Press function button 2 < >.
Tu r n < > t o s e l e c t t h e
position(digit) or number to set,
and press the < > button.
Press function button 4 < > to
return to the shooting-ready state.
ØWhen transmission between the
master un it an d slave unit is
established, the <LINK> lamp is lit
in green.(Refer to page 28)
To avoid interference, Set the same channel and ID
for both the master unit and slave unit.
Set a flash that is compatible with radio transmission
wireless flash shooting as the slave unit. For the slave
unit settings, see the flashs instruction manual.
ID
8
Setting the Master Unit Transmission Channel /
Wireless Radio ID.
Scanning while “AUTO” is set
Scanning while Ch. 1 to 15 is set
Scanning the Master Unit Transmission Channels to Set
You can scan the radio reception status and set the master unit’s
transmission channel automatically or manually. When the
channel is set to “AUTO”, the channel with the best reception
signal is automatically set. When setting the channel manually,
you can set the transmission channel again while referring to the
scan results.
Wireless Settings
Run the scan.
Press function button 4 to display
< >.
Press function button 3 < >.
ØThe channel is reset to one with a
good reception signal.
2.Set a channel.
Turn< >to select a channel
from Ch1 to 15.
Press the < > button to set
the channel and return to the
shooting ready state.
1.Run the scan.
Press function button 4 to display
< >.
Press function button 3 < >.
T h e ra d i o r e c e p t i o n s t at u s i s
displayed in a graph.
The higher the peak of the channel in
the graph, the better the radio reception
signal.
9
ETTL:Fully Automatic Wireless Flash Shooting
1.Set the flash as the slave unit A,
B or C . The flash will not fire if
it is set to D or E.
2.Set the same channel and ID of
the master unit and slave unit
.(p.8)
3.Position the camera and the
flash.(p.7)
4.Press the <MODE> button on
the master unit and set the
flash mode to <ETTL>.
The slave unit is set automatically
to <ETTL> during shooting via the
control from the master unit.
5.Check the transmission status
and that the flash is ready.
Check that the <LINK> lamp is lit
in green.
Check that the < > slave flash-
ready icon is lit on the master unit’s
LCD panel.
When the recycling of all the flash
units is completed, the master unit's
charge lamp lights.
6.Check the operation.
Press the master unit’s test flash
button (charge lamp). The slave unit
flashes.
7.Take the picture.
If a standard flash exposure was
o b t a i n e d , t h e f l a s h e x p o s u r e
confirmation lamp lights for 3 sec.
10
FEC (Flash Exposure Compensation)
FEB (Flash Exposure Bracketing)
1.Press function button 4 to display < >.Press function
button 2 < >. < > is displayed and the FEC amount
is highlighted.
2.Turn < > to set the flash exposure compensation amount,
and press < >. The FEC amount is set.
To cancel FEC, return the amount to “±0.
Support 1/3-stop increments to set FEC/FEB within ±3.
1.Press function button 4 to display < >. Press function
button 3 < >. < > is displayed and the FEB level display
is highlighted.
2.Turn < > to set the FEB level, and press < >. The FEB
level is set.
W h e n u s e d t o g e t h e r w i t h f l a s h e x p o s u r e
compensation, FEB shooting is performed based on the
flash exposure compensation amount.
ETTL:Fully Automatic Wireless Flash Shooting
11
High-speed Sync
With the high-speed sync function, the flash can synchronize
with all shutter speeds. This is convenient when you want to
use aperture-priority AE for fill-flash portraits of a subject.
1.Display < >.
Press function button 4 to display
< >.
2.Display < >.
Press function button 2 < > to
display < >.
Check that < > is lit in the viewfinder.
FELFE Lock
FE (Flash Exposure) lock locks the correct flash exposure setting
for any part of the scene.
Perform FE lock by operating the camera. For the operations,
see the camera and flashs instruction manual.
About Master Units
You can use two or more master units (master units + slave
units =maximum of 16 units). By preparing multiple cameras
with master units attached, you can shoot by changing cameras
while keeping the same lighting (slave units).
Note that when using two or more master units, the color of the
<LINK> lamp varies depending on the order in which the power
was turned on. The first master (main master) is green and the
second and subsequent masters (sub-masters) are orange.
12
ETTL:Fully Automatic Wireless Flash Shooting
C
A
B
T h e e x p o s u r e i s c o n t r o l l e d
automatically so that the total
fl ash out pu t of firi ng gr ou ps
results in the standard exposure.
1.Set the firing group of the
slave units.
Operate and set the slave units
one by one.
2 . P r e s s t h e m a s t e r u n i t s
function button 4 to display
< >.
3.Press function button 2
< > and set to <A:B> or
A:BC>.
4. Set t he f la sh r at io .Press
function button 3 < >.
Press function button 3 < >
or < >.
Turn < > to set the flash ratio
or the flash exposure, and press
the < > button.
Press function button 4 < >
to return to the shooting-ready
state.
5.Take the picture.
The slave units flash at the set
flash ratio.
ETTL: Wireless Multiple Flash Shooting with Flash Ratio
A:B
/
+
-
/
+
-
C
13
Slave Group Control
Firing group A
If you need more flash output or wish
to perform more sophisticated lighting,
you can increase the number of slave
units.
Simply set an additional slave unit to
the firing group (A, B or C) whose flash
output you want to increase. You can
increase the number of slave units up
to 15 units in total.
For example, if you set a firing group with three slave units to
<A>,the three units are controlled as a single firing group A with
a large flash output.
To fire the three firing groups A, B and C at the same time, set
<A:B:C>. With the < A:B > setting, firing group C does not fire.
If you shoot with firing group C pointing directly toward the
main subject, overexposure may result.
The flash ratio of 8:1 to 1:1 to 1:8 is equivalent to 3:1 to 1:1 to
1:3 (1/2-stop increments) when converted to number of stops.
The details of the flash ratio settings are as follows.
14
Modeling Flash
Modeling Flash from a Master Unit
Press the depth-of-field preview
button on the camera.
The flash fires continuously for 1
sec.
ETTL: Wireless Multiple Flash Shooting with Flash Ratio
M: Wireless Multiple Flash Shooting with Manual Flash Output
1.Set the flash mode to <M>.
2.Set the number of firing groups.
While < > is displayed, press
function button 2 < > and set
the groups to fire.
The setting changes as follows
each time you press the button:
ALL(RATIO OFF)
A/B(RATIO A:B)
A/B/C(RATIO A:B:C)
3.Select a firing group.
Press function button 3< >,
turn < > and select the group for
which you want to set the flash
output.
4.Set the flash output.
Press function button3< >.
Turn < > to set the flash output,
and press the < > button.
Repeat steps 3 and 4 to set the
flash output of all groups.
5.Take the picture.
Each group fires at the set flash
output.
This describes wireless (multiple flash) shooting using manual
flash.You can shoot with a different flash output setting for each
slave unit(firing group). Set all parameters on the master unit.
/
+
-
15
When ALL <RATIO OFF> is set, set A, B or C as the firing group
for the slave units. The flash will not fire if it is set to D or E.
To fire multiple slave units with the same flash output, select
ALL <RATIO OFF> in step 2.
M:The shutter sync of manual flash setting
1.Display < >.
Press f uncti on but to n 4 to
display< >.
2.Shutter Sync setting
While < > is displayed, press
function button 2 < > and set
the shutter sync.
The setting changes as follows
each time you press the button:
:High-speed Sync
:2nd Curtain Sync
(no icon):1st Curtain Sync
You can use 1st curtain Sync, high-speed Sync, or 2nd
curtain sync in manual flash.
16
The 2nd curtain sync can be
used in manual flash only.
When using the 2nd curtain
sync , wireless settings and
other parameters recommend
using the speedlite transmitter
settings.
MULTI: Stroboscopic Flash
In stroboscopic flash, set the flash output, number of
flashes, and flash frequency (number of flashes per second
= Hz).
1 . S e t t h e f l a s h m o d e t o
<MULTI>.
Press the <MODE> button on
the
master unit and set to <MULTI>.
2.Set the firing groups and the
flash output.
Set the number of firing groups
and the flash output for each
group by referring to the manual
flash on the preceding page.
3.Set the flash frequency and
thenumber of flashes.
While < > is displayed,
perform the following procedure.
To set the number of flashes,
press function button 2 < >,
turn < > and select < >.
To set the flash frequency, press
function button 3 < >, turn
< > and select < >.
17
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72

Yongnuo YN-E3-RT ユーザーマニュアル

カテゴリー
カメラが点滅する
タイプ
ユーザーマニュアル

他の言語で