TTL无线引闪器
TTL Wireless Flash Trigger
For Nikon
说 明 手 册
Instruction Manual
中英文双语
Chinese English Bilingual
705-X1N000-00 Made In China
地址/Add: 深圳市宝安区福永镇福洲大道西新和村华发工业园A4栋
Building A4, Xinhe Huafa Industrial Zone, Fuzhou RD West, Fuyong
Town, Baoan District, Shenzhen 518103, China
电话/Tel: +86-755-29609320(8062) 传真/Fax: +86-755-25723423
邮箱/E-mail: [email protected]
深圳市神牛摄影器材有限公司
GODOX Photo Equipment Co., Ltd
Technical Data
X1NModel
Yes (0~10ms, use 100us as the unit)
Receiver can control camera shooting through 2.5mm sync port
Adjust the flash's focal length through the transmitter
Wide LCD panel, backlight on/off
Transmitter: use a PC cord to input and output
Receiver: use a 2.5mm sync cord to output
Use the Micro USB port to upgrade
Settings will be stored 2 seconds after last operation and
recover after a restart
72x75x52(mm)/100g
70x65x47(mm)/70g
Others
Synchronization delay set
Wireless shutter release
ZOOM setting
LCD panel
Output interface
Firmware upgrade
Memory function
Dimension/Weight for Transmitter
Dimension/Weight for Receiver
前言
安全须知
部件
机身
LCD显示屏
附件
电池
安装电池
低电池电量指示
使用引闪器
无线同步触发影室闪光灯
无线同步触发机顶闪光灯
无线触发相机快门
使用PC接口无线触发影室闪光灯或机顶闪光灯
02
02
04
07
08
目录
设置发射器
电源开关
AF对焦辅助灯开关
频道设置
模式设置
当前分组值设置
频闪分组开关设置
频闪参数设置
群组值设置
试闪
自动进入省电模式
C.Fn：设置自定义功能
无线快门模式
照相机方的设置
设置接收器
频道设置
组别设置
自动进入省电模式
注意事项
引闪器的保养
规格参数
10
16
17
18
18
感谢您购买X1N TTL无线引闪器。
该TTL无线引闪器可与一台发射器和一台或多台接收器组合使用，以远距离触发相机快
门、影室闪光灯和机顶闪光灯。多频道控制，信号稳定，反应灵敏，方便摄影师灵活布光，
满足多种拍摄需求。该引闪器适用NIKON数码单镜反光相机，同时可以连接具有PC接口的
相机使用。支持高速闪光同步，最大闪光同步速度达1/8000s*，可用于操作支持i-TTL的机
顶灯。也可用于引闪影室闪光灯，实现高速同步。
*：限制条件——相机的最大快门速度为1/8000s。
前言
请勿拆卸或改造
违反此警告可能会触电或导致产品故障。若本产品因为摔落或其他意外事故造成破损，
请取出电池并将产品送至厂家授权的维修中心进行检查维修。
保持干燥
请勿用湿手接触产品，亦不可将产品浸入水中或暴露于雨中，否则可能引起火灾或触
电。
请勿在易燃气体环境中使用
违反此警告可能引起爆炸或火灾。
安全须知
为防止损坏您的相机，或避免您或他人受伤，在使用本设备前请仔细阅读下面的安全须
知，并妥善保管以便所有本产品使用者可随时参阅。
请遵守本节中所列举的各项预防措施，否则可能对产品造成损害。
以下标记表示警告，提醒您应该在使用本产品前阅读这些信息，以防止可能发生的损害。
- 02 -- 01 -
请勿在儿童伸手可及之处保管本产品
本产品包含可能引起窒息的零件。如果儿童不小心吞食了零件，请立即送往医院救治。
若发生任何故障，请立即关闭触发器电源
若发现本产品冒烟或发出异味，请立即取出电池并将本产品送至授权的维修中心进行检
查维修，以避免燃烧。若在此情景下继续使用，可导致受伤。
请勿置于高温中
请勿将本产品放置于阳光直射下的封闭车辆内或其他极高温的地方，否则可能导致火灾
或损坏本产品的外壳或内部部件。
使用电池的注意事项
操作不当可能导致电池漏液或爆裂，因此在使用本产品时，请注意以下事项，正确使用
电池：
只能使用本手册中列出的电池。请勿混用新旧电池或不同类型的电池。
请仔细阅读并遵守由厂商提供的警告或指示。
切勿使电池短路或拆卸电池。
切勿将电池投入火中或加热升温。
切勿试图以反方向安装电池。
当电量用尽时，电池容易漏液。所以为了避免产品受损，请在长期不使用本产品或
电量用尽时取出电池。
如果受损电池中的液体接触到皮肤或衣服，请立即用大量清水冲洗。
安全须知
- 03 -
发射器
部件
电源开关
--ON 打开电源
--OFF 关闭电源
AF辅助对焦灯开关
--ON 辅助对焦灯输出
--OFF 无辅助对焦灯输出
STATUS状态指示灯
--红色LED显示
MODE选定组模式设置按钮
TEST触发按键
--半按
--全按
CH频道设置按钮
GR组别设置按钮
Micro USB接口
PC接口
电池仓(背)
组选定、值设定拨盘
触发机顶灯热靴
相机触发热靴
LCD显示屏
机身
- 04 -
部件
- 07 -
1. 相机遥控线(N1、N3) 2. 闪光灯同步线 3. 同步转换接头
附件
安装电池
滑开发射器与接收器背面的电池
盒盖，根据电池盒内的正负极指
示，分别装入2节AA电池(需另
购)。
低电池电量指示
电池电量较低时(2节电池<2.0V)，
低电图标会闪烁，此时请更换电
池，否则在距离较远时会出现漏
闪或不闪现象。
电池
2. 无线同步触发机顶闪光灯
使用方法：
2.1 关闭相机电源，将发射器放置于相机热靴插座上，打开发
射器电源开关，打开相机电源。
2.2 将机顶闪光灯插入接收器“触发机顶灯热靴”。
2.3 通过“频道设置按钮”选择频道，使发射器与接收器选择
的频道一致。
2.4 按下相机快门即可引闪，同时发射器与接收器“状态指示
灯”闪亮红色。
1. 无线同步触发影室闪光灯
使用方法：
1.1 关闭相机电源，将发射器放置于相机热靴插座上，打开发
射器电源开关和相机电源。
1.2 关闭影室灯电源，通过“闪光灯同步线”连接，两端分别
插入接收器“2.5mm快门接口”和闪光灯的“同步插
孔”，打开影室灯电源。
1.3 通过“频道设置按钮”选择频道， 使发射器与接收器选
择的频道一致。
1.4 按下相机快门即可引闪，同时接收器与发射器“状态指示
灯”闪亮红色。
此款引闪器具备以下功能：
使用引闪器
- 08 -
1
2
4. 使用PC接口无线触发影室灯或机顶闪光灯
使用方法：
4.1 接收器端连接方式请参考“无线同步触发影室闪光灯”和“无
线同步触发机顶闪光灯”章节。
4.2 发射器端缺省将PC接口作为输入口，控制接收器端的闪灯进行
闪光。
4.3 正常方式按下快门。将使用PC接口信号控制闪光。
4.4 P C 接口可以设置 为 输 出口，具体操作 ： 在发射器端长按
<CH>按钮，直到屏幕显示<Fn>，设置Fn 03 值为 1，将
PC接口设置为输出模式。
3. 无线触发相机快门
使用方法：
3.1 关闭相机电源，通过“相机遥控线”连接，两端分别插入接收
器的“快门接口”和相机的快门插座，打开相机电源。
3.2 半按下<TEST>触发按键，进行对焦；全按下<TEST> 触发按
键，进行拍摄，状态指示灯亮红色，直到按钮松开。
使用引闪器
- 10 -- 09 -
设置发射器
把电源开关拨至“ON”即可打开电源，状态指示灯不显示。
注意：长时间不使用时请关闭电源，以免耗电！
电源开关
AF对焦辅助灯开关
频道设置
1. 短按<CH>按钮，频道值闪烁。
2. 拨动拨盘选择合适的频道值。再次按<CH>按
钮，当前频道值被选定。
3. 引闪器共32个频道，可以在1-32频道之间切
换。使用前请务必将发射器和接收器置于相同
频道。
模式设置
1. 短按<MODE> 按钮，选中组的模式会改变。
2. 当前组的模式可以在TTL/M/--模式下顺序切
换(--代表OFF，当前组将不会闪光)。
把电源开关拨至“ON”，允许输出AF对焦光线。
1、要正确闪光，请将连接到发射器上或接收器上的机顶灯设置为
i-TTL自动模式。
2、要使用ZOOM设置功能，请开启机顶灯的自动ZOOM 功能。
3、如果需要进行高速连拍，请按照需要设置分组。设置为TTL 方
式的分组需要额外的预闪时间，连拍间隔会显著增加。关闭不
需要闪光的分组，或设置分组为M闪光模式，将有助于提高连
拍速度。
4、Nikon的CLS目前能控制四个分组(M/A/B/C)，对于分组D和
分组E，TTL模式不可用。
3
4
CH
CH
设置发射器
当前分组值设置
1. 短按<GR>按钮，可以对当前分组进行设置。
2. 当前分组值将会闪烁，拨动拨盘以改变设置
值。
3. 如果当前分组处于M模式，其功率输出值将在
1/128 ~ 1/1之间以0.3 为增量改变；如果当
前分组处于TTL模式，其FEC值在-3 ~ 3之
间以0.3 为增量改变；如果当前分组模式为-
-(关闭闪光)，则无影响。
4. 再短按<GR>按钮，以确认设置值。
群组值设置
1. 长按<GR> 按钮，可以对与当前分组模式相同的所有分组一起进行设置。
2. 所有与当前分组模式相同的分组值将会闪烁，使用拨盘以改变设置值。
3. 如果当前分组处于M模式，所有模式同样为M的分组的功率输出值都会同步调整。功率
输出值可以在1/128~1/1之间以0.3为增量改变，直到其中一个分组的值达到最大
(1/1)或最小(1/128); 如果当前分组处于TTL模式，所有模式同样为TTL的分组的
FEC值都会同步调整。FEC值可以在-3~3之间以0.3 为增量改变，直到其中一个分组
设置值达到最大(3)或最小(-3); 如果当前分组模式为--(关闭闪光)，则无影响。
4. 短按<GR>按钮，以确认设置值。
- 11 -
设置发射器
频闪分组开关设置
1. 在自定义功能中开启频闪模式(C.Fn-04设置
为1)。
2. 短按<MODE> 按钮，选中组的模式会改变。
3. 当前组的模式可以在on/- - 模式下顺序切换
(--代表OFF，当前组将不会闪光)。
频闪参数设置
1. 在进入频闪模式之后才能设置。
2. 长按<MODE> 按钮，进入频闪参数设置子菜
单。
3. 三行显示内容分别为 P(输出值)，T(闪光次
数)，H(闪光频率)。
4. 短按<GR>按钮，可以选择对应设置值，在设
置值闪烁时，拨动转盘修改设置值。继续短按
<GR>按钮, 直到三项设置值都设置完毕。短
按<MODE>按钮，将退出设置状态。
闪光次数受闪光输出值和频率联合制约，闪光次数可能会自动调整。
传输到接收端的次数会是实际闪光次数，同相机的快门设置也相关。
X1T-N发射器+机顶灯或X1R-N接收器+机顶灯频闪只能有一次闪光，这是由Nikon通讯协议决定
的！但在接收器模式下工作的 TT685N、AD360II能够被正确引闪。
- 12 -
CH
CH
设置发射器
试闪
1. 按<TEST>触发按钮，可以测试闪光是否正
常。
2. 全按下<TEST>触发按键，此时状态指示灯
亮红色，引闪接受器端闪光灯。
3. 或使用发射器控制相机对焦、拍摄，此时接
收器端与相机相连(不再连接闪光灯)。
4. 在待机模式时，可以按 TEST 按钮以唤醒
接收器。
5. 发射器端的设置值将同时同步到接收器中。
自动进入省电模式
1. 在停止操作发射器超过 60 秒之后，系统自动进入待机模式，此时LCD显示消失。
2. 要唤醒系统，可以按任意键(<TEST>全按/<CH>/<GR>/<MODE>)。如果发射器安
装在NIKON数码单镜反光相机热靴上，也可以通过半按相机快门唤醒系统。
3. 如果发射器设置了单触点模式（ 显示），将不会进入省电模式。
- 14 -
请对照以下图表本机应用栏，使用自定义功能来完成设置。“√”表示该闪光灯支持自定
义设置，“0”表示不支持自定义设置。
注：如果对应的自定义功能开启有图标显示，则设置时，该图标会显示，以便于用户了解。
设置和说明
关闭
主闪时延N*100us闪光(时延图标 显示)
关闭
启动(单触点模式已设置图标 显示)
如果发射器用PC线连接相机引闪或相机通过
单触点引闪，建议将发射器设置成单触点模式
跟随相机Zoom值改变，需要开启闪灯自动
ZOOM值功能
固定Zoom值(20/24/28/35/50/70/
80/105/135/200mm)
PC接口连接相机
PC接口连接闪灯
频闪闪光关闭
频闪闪光开启
设置编号
0
1~100
0
1
AU
20,24,28,35,50,70,
80,105,135,135+
0
1
0
1
功能
同步时延设置
单触点模式
设置Zoom值
PC接口连接
相机/闪光灯
频闪闪光开
启、关闭
自定义功能编号
C.Fn-00
C.Fn-01
C.Fn-02
C.Fn-03
C.Fn-04
√
√
√
√
本机应用
设置发射器
C.Fn：设置自定义功能
√
- 13 -
- 15 -
设置发射器
无线快门模式
半按下<TEST>触发按键，进行对焦；全按下<TEST>触发按键，此时状态指示灯亮红
色，进行拍照，直到松开按钮，指示灯熄灭。
照相机方的设置
为使FP高速闪光，在相机上将个人设定“e1:闪光灯同步速度”设置为“1/250秒(自动
FP)”，以便从标准同步模式平稳过渡到高速同步模式。不要使用1/320秒(自动FP)。
1. 长按<CH>按钮2秒或更长，直到显示<Fn>
2. 选择自定义功能编号。
* 旋转调节旋钮设置自定义功能编号。
3. 更改设置。
* 按<GR>设置按钮，自定义功能编号闪烁。
* 旋转调节旋钮设置想要的编号，按<GR>按钮确定。
* 设置自定义功能后按下<MODE> 模式选择按钮，退出C.Fn设置状态。
设置接收器
频道设置
1. 短按<CH>频道按钮，频道值每次增加1。
2. 长按<CH>频道按钮，进入快调模式，频
道值会快速增加。
3. 无论是短按还是快调，松开<CH>按钮，
当前频道值被设置。
4. 频道值会在01~32中有序增加，在32频道
时继续调节，将转换到频道1。
组别设置
1. 短按<GR>分组按钮，分组值每次增加1。
2. 长按<GR>分组按钮，进入快调模式，分
组值会快速增加。
3. 无论是短按还是快调，松开<GR>按钮，
当前分组值被设置。
4. 分组值会在A~E中有序增加，在E组时继
续调节，将转换到分组A。
- 16 -
GR
CH
GR
CH
- 17 -
注意事项
1. 如不能正确引闪或拍摄，请检查电池是否正确安装以及是否打开引闪器电源；引闪器是否
设置在同一频道；连接线或热靴口是否已正确牢固连接到位；功能模式是否设置正确。
2. 如相机出现只能拍摄不能对焦现象，请检查机身或镜头是否设定为MF手动对焦，请设置
为AF自动对焦。
3. 如您的引闪器受到他人干扰引闪或拍摄，改变引闪器的频道设置即可。
4. 如您发现触发距离有限或者有漏闪现象，请检查是否电池耗尽，请尝试更换电池。
5. 如果发射器已经插入相机热靴并且电源开关已打开，但在相机的取景器中无法看到< >
图标或< >图标闪烁，表明发射器工作不正常，请确保热靴接口与相机连接无误，再重
启发射器电源开关。
设置接收器
自动进入省电模式
1. 在发射端进入休眠模式之后，系统自动进入待机模式，此时LCD显示消失。
2. 要唤醒系统，可以按<TEST>按钮或<GR>按钮。也可通过发射器唤醒(发射器端全按
<TEST>触发按钮)，如果发射器安装在NIKON数码单镜反光相机热靴上，也可以半
按相机快门。
- 18 -
引闪器的保养
避免跌落：如果受到强烈碰撞或振动，引闪器可能会发生故障。
保持干燥：本产品是非防水产品，如果将其浸入水中或放置于高湿度的环境中将可能发生故
障。内部构造生锈可能会导致无法修理的损害。
避免温度骤变：温度的突变，诸如在寒冷天进出温暖的大楼将可能会使引闪器内部结露。为
避免结露，请将引闪器事先装入手提袋或塑料包内，以防温度突变。
远离强磁场：无线电广播发射机等设备产生的强静电或强磁场可能会干扰本产品正常工作。
型号
类型
兼容相机
内置无线
调制方式
供电方式
曝光控制
手动闪光
TTL自动闪光
TTL控制
高速同步
曝光补偿
曝光锁定
X1N
Nikon版
Nikon数码单镜头相机(i-TTL自动闪光)
支持所有具有 PC 输出口的相机
2.4G频率
MSK
2*AA 电池
有
i-TTL
有
有，±3档间以1/3档为增量调节
有
规格参数
- 19 -
型号
TTL控制
辅助对焦
频闪闪光
后帘同步
造型闪光
无线闪光
无线功能
X1N
手动开启
支持(AD360II/TT685N 用作接收器)
支持(在相机上设置)
有，使用相机的景深预视按钮进行闪光
兼容Nikon CLS创意闪光系统(Creative Lighting System)
规格参数
可控从属单元组
传输范围(约)
频道
其他
时延设置
无线快门
ZOOM设置
显示屏
输出接口
固件更新
记忆功能
发射器尺寸/净重
接收器尺寸/净重
最多6组(M/A/B/C/D/E)
>100米
32个
有(0~10ms，以100us为单位设置)
接收器端可以通过2.5mm同步接口控制相机拍摄
可以通过发射器调节闪灯焦距值
宽屏液晶显示，背光开启或关闭
发射器：PC 端子输入、输出；接收器：2.5mm同步线输出
通过机身上的 Micro USB进行固件升级
设置2秒后的参数会自动记忆，重新开机自动恢复
72x75x52(mm)/100g
70x65x47(mm)/70g
Foreword
For Your Safety
Names of Parts
Body
LCD Panel
Accessories
Battery
Installing Batteries
Low Battery Level Indication
Using the Flash Trigger
As a Wireless Studio Flash Trigger
As a Wireless Speedlight Trigger
As a Wireless Shutter Release
As a Wireless Studio Flash Trigger
or Speedlight
Trigger with PC Sync Socket
21
21
23
26
27
Setting the Transmitter
Power Switch
Power Switch of AF Assist Beam
Channel Settings
Mode Settings
Current Group Settings
Multi Flash Group ON/OFF Settings
Multi Flash Parameter Setting
Group Settings
Test Flash
Automatically Enter Power Saving Mode
C.Fn: Setting Custom Functions
Wireless Shutter Release Mode
Setting the Camera
Setting the Receiver
Channel Settings
Group Settings
Automatically Enter Power Saving Mode
Attentions
Caring for Flash Trigger
Technical Data
29
35
37
37
38
Contents
- 20 -
Do not use in the presence of flammable gas
Failure to observe this precaution could result in explosion or fire.
Keep out of reach of children
This device contains small parts which may pose a choking hazard. Consult a physician
immediately if a child swallows any part of this device.
Turn off the transceiver immediately in the event of malfunction
Should smoke or an unusual smell comes from this device, remove the batteries immediately in
case of burning and take the device to an authorized maintenance center for inspection.
Injuries could occur if it is further used.
Do not expose to high temperature
Do not leave the device in a closed vehicle in the sun or in other areas subject to
extremely high temperature. Failure to observe this precaution could result in fire or damage to
the casing or internal parts.
Observe precautions when handling batteries
Batteries may leak or explode if improperly handled. Observe the following precautions when
handling batteries for use in this device:
Use only batteries listed in this manual. Do not use old and new batteries or batteries of
different types at the same time.
Read and follow all warnings and instructions provided by the manufacturer.
Batteries cannot be short-circuited or disassembled.
Do not put batteries into a fire or apply direct heat to them.
Do not attempt to insert batteries upside down or backwards.
Batteries are prone to leakage when fully discharged. To avoid damage to the product, be
sure to remove batteries when the product is not used for a long time or when batteries run
out of charge.
Should liquid from the batteries come into contact with skin or clothing, rinse immediately
with fresh water.
Foreword
Thanks for your purchase of this X1N TTL wireless flash trigger.
This TTL wireless flash trigger can be used with a transmitter and one or more receivers for studio
flash, speedlight, and camera shutter. Featuring multi-channel triggering, stable signal transmission,
and sensitive reaction, it gives photographers unparalleled flexibility and control over their strobist
setups. The flash trigger applies to hotshoe-mounted Nikon DSLR series cameras, as well as the
cameras which have PC sync sockets.
With X1N wireless flash trigger, high speed synchronization is available for most of camera flashes
in the market which support i-TTL. The max flash synchronization speed is up to 1/8000s *.
*: 1/8000s is achievable when the camera has a max camera shutter speed of 1/8000s.
- 21 -
For Your Safety
- 22 -
To prevent damage to your product or injury to you or to others, read the following safety
precautions in their entirety before using this device. Keep these safety instructions where all those
who use this device will read them.
Failure to observe the precautions listed in this section could result in damage to the product.
The following icon indicates warnings that should be read before using this device in case of
possible damage or injury.
Do not disassemble or modify
Failure to observe this precaution could result in electric shock or product malfunction.
Should the product break open as the result of a fall or other accident, remove the batteries and
take the product to an authorized maintenance center for inspection.
Keep dry
Do not handle with wet hands or immerse in or expose to water or rain. Failure to observe this
precaution could result in fire or electric shock.
For Your Safety
- 23 -
MODE Mode Selection Button
CH Channel Setting Button
GR Group Setting Button
Select Dial
Hot Shoe Camera
Connection
LCD Panel
Names of Parts
- 24 -
Transmitter
Power Switch
--ON (Power On)
--OFF (Power Off)
AF Assist Beam Switch
--ON(AF Assist Beam outputs)
--OFF(AF Assist Beam do
not output)
Status Indicator Lamp
--LED Red Color Lamp
TEST Trigger Button
--Half Press
--Fully Press
Micro USB Port
PC Sync Socket
Battery
Compartment
Hot Shoe Speedlight
Connection
Body
Names of Parts
2.5mm Shutter
Release Port
Receiver
TEST Trigger Button
Power Switch
--ON (Power On)
--OFF (Power Off)
Status Indicator Lamp
--LED Red Color Lamp
CH Channel Setting Button
GR Group Setting Button
LCD Panel
Hot Shoe Speedlight
Connection
Micro USB Port
Battery
Compartment
GRCH
CH
Gr
- 25 -
Names of Parts
(A) Group Setting (B) Channel Setting (C) Low Battery Indicator
Receiver Panel
- 26 -
(A) Output Settings per Group in the M Mode; FEC Settings per Group in the TTL Mode
(B) Mode Settings (C) Group (D) Currently Selected Group (E) Channel Settings
(F) GR Grouping Icon (G) Synchronization Delay Setting Icon (H) Low Battery Indicator
(I) Single Contact Icon
AB
C
D
E
F
G
H
I
Transmitter Panel
C
BA
Installing Batteries
As shown in the illustration, slide the battery compartment lid of the transmitter and
receiver and insert two AA batteries (sold separately)separately.
Low Battery Indication
When the battery power (2 AA
batteries <2.0V) gets low,
Status Indicator Lamp blinks
quickly (blink cycle=0.5s).
Please replace new batteries,
as low power leads to no flash
or flash missing in case of
long distance.
Battery
Names of Parts
1. Remote Cable(N1, N3) 2. Sync Cable 3.Sync Adapter
Accessories
- 27 -
1. As a Wireless Studio Flash Trigger
1.1 Mount the transmitter on camera hotshoe and turn it on before
turning on the camera.
1.2 Connect the receiver to studio flash by Sync Cable (one end in
2.5mm Shutter Release Port of the receiver, the other end in
sync port of studio flash) before turning on the studio flash.
1.3 Set the transmitter and the receiver to the same channel.
1.4 Press the camera shutter button, and the studio flash will be
triggered simultaneously. Status Indicator Lamp of both
transmitter and receiver units turn red.
The flash trigger features the following functions:
Using the Flash Trigger
2. As a Wireless Speedlight Trigger
2.1 Mount the transmitter on camera hotshoe and turn it on before
turning on the camera.
2.2 Mount the speedlight to Hot Shoe Speedlight Connection of
receiver unit. Set the speedlight to M mode.
2.3 Set the transmitter and the receiver units to the same channel.
2.4 Press the camera shutter button, and the speedlight will be
triggered simultaneously. Status Indicator Lamp of both
transmitter and receiver units turn red.
- 28 -
3. As a Wireless Shutter Release
3.1 Connect the receiver and the camera by Remote Cable (one
end in receiver’s Shutter Release Port, the other end in
camera’s shutter port) before turning on the camera.
3.2 Half press the <TEST> Trigger Button to focus. When fully
press the <TEST> Trigger Button to shoot, the Status Indicator
Lamp will turn red until releasing the button.
Using the Flash Trigger
4. As a Wireless Studio Flash Trigger or Speedlight Trigger with
PC Sync Socket
4.1 The connection method of the receiver can be found in As a
Wireless Studio Flash Trigger and As a Wireless Speedlight
Trigger section.
4.2 The transmitter will control the flash on the receiver end to fire
via using PC Sync Socket as input by default.
4.3 Press the camera shutter and use the PC Sync Socket’s signal
to control the flash.
4.4 PC Sync Socket can also be set as output. Long press the
<CH> Button of the transmitter until <Fn> is displayed on the
panel. Then, set the value of Fn 03 to 1, and the PC Sync
Socket is under output mode.
1. To fire flashes normally, please set the camera flash which
connects to the transmitter or receiver to i-TTL mode.
2. To set ZOOM functions, please open the ZOOM functions on
the camera flash.
3. If high-speed continuous shooting is needed, please set the
groups as required. The shot-to-shot will increase noticeably for
the group that set to TTL mode needs extra preflash time. Turn
off the needless flash groups or set them to M mode to improve
continuous shooting speed.
4. Nikon's CLS system can only control four groups (M/A/B/C). D
and E group cannot be used in TTL mode.
1
2
3
4
CH
CH
CH
- 29 -
Setting the Transmitter
Slide the Power Switch to ON, and the device is on and Status Indicator Lamp will not blink.
Note: In order to avoid power consumption, turn off the transmitter when not in use.
Power Switch
Slide the power switch to ON, and the AF lighting is allowed to output.
Power Switch of AF Assist Beam
Channel Setting
1. Short press the <CH> Button until the channel
amount blinks.
2. Turn the Select Dial to choose the appropriate
channel. Press the <CH> Button again to confirm
the setting.
3. This flash trigger contains 32 channels which can
be changed from 1 to 32. Set the transmitter and
the receiver to the same channel before usage.
- 30 -
Setting the Transmitter
Mode Setting
1. Short press the <MODE> Button, and the mode
of the current group will change.
2. The current group's mode will be changed by the
order of TTL/M/-- modes (-- means OFF, and the
current group will not fire a flash in this mode).
Current Group Settings
1. Short press the <GR> Button to set the current
group.
2. The current group settings will blink and turn
the Select Dial to change the settings.
3. When the current group is in the M mode, the
power output value is changeable from 1/1 full
power to 1/128th power in 0.3 stop increments.
When the current group is in
the TTL mode, the FEC amount is changeable
from -3 to 3 in 0.3 stop increments. When the
current group is in the -- mode (flash off), the
amounts will not change.
4. Short press the <GR> Button again to confirm
the setting.
Multi Flash Group ON/OFF Settings
1. Open the multi flash in the C.Fn Custom
Functions (set C.Fn-04 as 1).
2. Short press <MODE> button to change the
mode of selected group.
3. The current group’s mode will be changed
simultaneously by the order of on/-- (--
represents OFF, which means that the current
group will not fire flashes in this mode).
CH
Setting the Transmitter
Multi Flash Parameter Setting
1. Enter into multi flash mode before setting.
2. Long press the <MODE> Button to enter multi
flash parameter setting menu.
3. Then, P (output value), T (flash times) and H
(flash frequency) will be displayed on the LCD
panel.
4. Short press the <GR> Button to choose the
settings. Turn the Select Dial to change the
blinking setting amount. Continue to press the
<GR> Button until all the amounts are set.
Then, short press the <MODE> Button to exit.
As flash times are restricted by flash output value and flash frequency, it might get automatic
adjustment.
The times that transported to the receiver end are a real flash time, which is also related to the
camera’s shutter setting.
X1T-N transmitter + camera flash or X1R-N receiver + camera flash uses multi flash function can
only have one flash, which is determined by Nikon Communication Protocol. However, TT685N and
AD360II can be triggered normally when working as receivers.
Setting the Transmitter
Group Settings
1. Long press the <GR> Button to set all the groups that in the same modes simultaneously.
2. The settings of the groups which are in the same mode with the current group will blink. Turn
the Select Dial to change the settings.
3. If the current group is in the M mode, all the other groups which are in the M mode will change
their power output value simultaneously. The power output value is changeable from 1/1 full
power to 1/128th power in 0.3 stop increments, until one of the group’s setting turns to the
maximum(1/1) or the minimum(1/128). If the current group is in the TTL mode, all the other
groups which are in the M mode will change their FEC amount simultaneously. The FEC
amount is changeable from -3 to 3 in 0.3 stop increments, until one of the group’s setting turns
to the maximum(3) or the minimum(-3). If the current group is in the -- mode (flash off), the
amounts will not change.
4. Short press the <GR> Button again to confirm the setting.
Test Flash
1. Press the <TEST> Trigger Button to see the
whether flash will fire normally or not.
2. Fully press the <TEST> Trigger Button, and the
Status Indicator Lamp turns red and the flash on
the receive end can be triggered.
3. Use the transmitter to control camera to focus or
shoot, and the transmitter is connecting to the
camera (do not connect to the flash) now.
4. In the standby mode, press the TEST Button can
wake up the receiver.
5. The settings on the transmitter end will
synchronize to the receiver end at the same time.
- 32 -
- 31 -
Setting the Transmitter
Automatically Enter Power Saving Mode
1. The flash trigger will go into standby mode after the transmitter enter sleep mode, and the
displays on the LCD panel will disappear.
2. Press any of the button (<TEST> fully pressed/<CH>/<GR>/<MODE>) can wake up the flash
trigger. If the transmitter is attached to the Nikon DSLR camera, half press the shutter can
also wake up the system.
3. If the transmitter is set to single contact mode( isdisplayed), the system will not enter
power saving mode.
Setting the Transmitter
The following table lists the available and unavailable custom functions of this flash. The icon “√”
indicates the flash custom function is supported but “0”indicates the custom function is not
supported.
Note: Some icons will be displayed when setting the relevant custom functions to make users have a good
understanding.
ON(The single contact mode set icon
is displayed.)
It is advisable to set the transmitter to single
contact mode when using it to trigger the flash
by PC cord or through camera’s single contact.
Settings and Description
OFF
Master flash synchronization delay N*100 us
(synchronization delay icon is displayed.)
OFF
Setting Signs
0
1~100
0
1
Functions
Synchronization
delay setting
Single contact
mode
Custom
Functions No.
C.Fn-00
C.Fn-01
Application
√
√
- 34 -
C.Fn: Setting Custom Functions
√
Settings and Description
Changing with camera's zoom value, Flash's
auto ZOOM functions should be turned on.
Zoom(20/24/28/35/50/70/80/105/135/
200mm)
PC sync socket connects with camera
PC sync socket connects with flash
Multi Flash OFF
Multi Flash ON
Setting Signs
AU
20,24,28,35,50,70,
80,105,135,135+
0
1
0
1
Functions
Zoom setting
PC sync socket
connects with
camera/flash
Multi Flash
ON/OFF
Custom
Functions No.
C.Fn-02
C.Fn-03
C.Fn-04
Application
√
√
1. Press the <CH> Button for 2 seconds or longer until <Fn> is displayed.
2. Select the custom function No.
* Turn the Select Dial to choose the Custom Function No.
3. Change the Setting.
* Press the <GR> Button until the custom function No. blinks.
* Turn the Select Dial to set the desired number. Pressing <GR> button will confirm the settings.
* Press <MODE> button to exit the C.Fn settings.
Wireless Shutter Release Mode
Half press the <TEST> Trigger Button to focus. Fully press the <TEST> Trigger Button, and the
Status Indicator Lamp turns red. Now camera is ready to shoot. When releasing the button, the
Status Indicator Lamp turns off.
- 33 -
GR
CH
Setting the Transmitter
Setting the Camera
To achieve FP flash, set “e1: flash sync speed” to “1/250s (Auto FP)” in the Nikon camera setting
to get a stable transition from standard sync mode to high speed sync mode. Do not use 1/320s
(Auto FP).
- 36 -
Setting the Receiver
Channel Setting
1. Short press the <CH> Button and the channel
amount will increase a step each time.
2. Long press the <CH> Button will enter quicker
adjustment mode. The channel amount will
increase fast in this mode.
3. Release the <CH> Button and the current channel
amount is confirmed.
GR
CH
Setting the Receiver
4. The channel amount will increase from 1 to 32. When the current channel is 32, press the
<CH> Button again and the channel 1 will be displayed on the panel.
Group Settings
1. Short press the <GR> Button and the group
amount will increase a step each time.
2. Long press the <GR> Button will enter quicker
adjustment mode. The group amount will increase
fast in this mode.
3. Release the <GR> Button and the current group
amount is confirmed.
4. The group amount will increase from A to E. When
the current group is E, press the <GR> Button
again and the group A will be displayed on the
panel.
Automatically Enter Power Saving Mode
1. The system will go into standby mode after the transmitter goes into standby mode. And the
displays on the LCD panel disappear now.
2. To wake up the system, press the <TEST> Button or the <GR> Button. Fully press the
<TEST> Trigger Button of the transmitter can also wake up the receiver’s system. If the
transmitter is attached to the NIKON DSLR camera, half press the camera shutter can also
wake up the system.
- 35 -
Attentions
1. Unable to trigger flash or camera shutter. Make sure batteries are installed correctly and Power
Switch is turned on. Check if the transmitter and the receiver are set to the same channel, if the
hotshoe mount or connection cable is well connected, or if the flash triggers are set to the correct
mode.
2. Camera shoots but does not focus. Check if the focus mode of the camera or lens is set to MF. If
so, set it to AF.
3. Signal disturbance or shooting interference. Change a different channel on the device.
4. Operating distance limited or flash missing. Check if batteries are exhausted. If so, change them.
5. No < > is displayed or < > is blinking on the camera viewfinder, though the camera is
mounted on the transmitter and the power switch is turned on. This is resulted from unusual
working of the transmitter. Check and make sure the flash trigger is well connected to the camera
through Hot Shoe Camera Connection, then power the Transmitter on again.
Caring for Flash Trigger
Avoid sudden drops. The device may fail to work after strong shocks, impacts, or excess
stress.
Keep dry. The product isn't water-proof. Malfunction, rust, and corrosion may occur and go
beyond repair if soaked in water or exposed to high humidity.
Avoid sudden temperature changes. Condensation happens if sudden temperature changes
such as the circumstance when taking the transceiver out of a building with higher temperature
to outside in winter. Please put the transceiver in a handbag or plastic bag beforehand.
Keep away from strong magnetic field. The strong static or magnetic field produced by
devices such as radio transmitters leads to malfunction.
- 37 - - 38 -
Technical Data
X1N
For Nikon
Nikon DSLR cameras (i-TTL autoflash)
Support for the cameras that have PC sync socket.
2.4G Wireless Transmission
MSK
2*AA batteries
Yes
i-TTL
Yes
Yes, ±3 stops in 1/3 stop increments
Yes
Manual open
Yes (AD360II/TT685N as receiver)
Yes (setting on the camera)
Yes, fired with camera's depth-of-field preview button
Compatible with Nikon CLS (Creative Lighting System)
Max. 6 groups (M/A/B/C/D/E)
>100m
32
Model
Type
Compatible Cameras
Builted-in remote system
Modulation mode
Power supply
Exposure Control
Manual flash
TTL autoflash
TTL Control
High-speed sync
Flash exposure compensation
Flash exposure lock
Focus assist
Multi Flash
Second curtain sync
Modeling flash
Wireless Flash
Wireless function
Controllable slave group
Transmission range(approx.)
Channel
/
