2. Kyosho
  3. MZW307 Aluminum Friction Post(MR-02/03 LM)

Kyosho MZW307 Aluminum Friction Post(MR-02/03 LM), MZW307@Aluminum Friction Post(MR-02/03 LM), MZW307�@Aluminum Friction Post(MR-02/03 LM) ユーザーマニュアル

  • こんにちは！京商 MINI-Z RACER MR-02/03 LMタイプ用 アルミフリクションポストの取扱説明書の内容を理解しました。この製品の取り付け方法や注意点、必要な工具などについてご質問があれば、お気軽にお尋ねください。スムーズな取り付けと製品の使用方法に関するご質問にお答えします。
  • シャシーの分解・組立前に何をすべきですか？
    この製品を使用するメリットは？
    組立てに必要な工具は何ですか？
    ネジの固定には何を使用することを推奨していますか？
Positive is Red
Negative is Black
2x6mm
2x6mm
2x6mm
1
2 x 6mm
Screw
7
TP2 x 6mm
TP Screw
*Illustration shows MR-03 chassis
but is same for MR-02 chassis.
*
R
THE FINEST RADIO CONTROL MODELS
INSTRUCTION SHEET
No.MZW307
Before beginning assembly, please read these instructions thoroughly!
Aluminum Friction Post
MINI-Z RACER MR-02/03 For LM Type
1
Thank you for purchasing this set. Before installation,
please carefully read and follow the instructions on
this sheet in conjunction with the instruction manual in
your MINI-Z RACER MR-02/03.
CAUTION
With this product, the rigity of the rear friction
shock increases assuring the accurate and
smooth movement of the suspension.
Be sure to remove the battery for operation before assembling or
disassembling the chassis.
MZW307-T01
< Assembly Caution >
Replace the screw with
the one shown below.
Must be purchased separately!
Tools required
Phillips Screwdrivers (Precision type or a small sized)
Positive is Red
Negative is Black
2x6mm
2x6mm
2x6mm
1
2 x 6mm
Screw
7
TP2 x 6mm
TP Screw
*Illustration shows MR-03 chassis
but is same for MR-02 chassis.
*
R
THE FINEST RADIO CONTROL MODELS
INSTRUCTION SHEET
No.MZW307
Before beginning assembly, please read these instructions thoroughly!
Aluminum Friction Post
MINI-Z RACER MR-02/03 For LM Type
1
Thank you for purchasing this set. Before installation,
please carefully read and follow the instructions on
this sheet in conjunction with the instruction manual in
your MINI-Z RACER MR-02/03.
CAUTION
With this product, the rigity of the rear friction
shock increases assuring the accurate and
smooth movement of the suspension.
Be sure to remove the battery for operation before assembling or
disassembling the chassis.
MZW307-T01
< Assembly Caution >
Replace the screw with
the one shown below.
Must be purchased separately!
Tools required
Phillips Screwdrivers (Precision type or a small sized)
Motor Holder
Remove Install
Insert correctly.
Air Intake
1
1
2
2
3
,
Follow steps above in reverse order to re-assemble.
1 2
60111004-1 PRINTED IN JAPAN
© Copyright 2010 KYOSHO CORPORATION
*SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
www.kyosho.com
www.mini-z.jp
243-0034 153
046-229-4115
() 13001900
/
< Assembly Caution > < Assembly Caution >
1
2 x 5mm
TP F/H Screw
Replace the screw with
the one shown below.
Replace this part with
the aluminum friction shock post.
It is recommended to
apply thread locker.
1
2 x 6mm
F/H Screw
2x5mm
2
/