Kyosho MINI-Z OVERLAND 取扱説明書

THE FINEST RADIO CONTROL MODELS

R

*Specifications are subject to change without prior notice!

Before beginning assembly, please read these instructions thoroughly.

30280-T01

Instruction Manual

Safety Precautions

Content

Equipments not included

Glossary of Main Parts

Before Operating

Let's Drive!

Operating Tips

Replacement for each part

Exploded View

Spare Parts

Trouble Shooting

/ Index

3~7

8

9

10

11~13

14~29

30~31

32~37

38~39

40~41

38

42

43

MINI-Z OVERLAND MV-01 Chassis Set ASF 2.4GHz

2

http://www.kyosho.com/mini-z-support/

Thank you for purchasing this product. This series uses the latest 2.4 GHz ASF system. The increased

processing speed of the RA-18M receiver amp unit delivers significantly faster response and the use of

high-efficiency FET contributes to sharp acceleration. For maximum enjoyment of this product,

please read this manual. A wide range of MINI-Z optional parts are available.

Please refer to the website below for the option parts list.

About This Model

ページが読み込まれています...

4

As the product includes small and sharp parts, assemble and

store this product only in places out of the reach of children.

Never disassemble the polarity required for installation.

This may lead to damage and leakage.

Cutters, wire cutter and screwdrivers need careful handling.

As the front end of the antenna may be dangerous,

do not swing or aim it toward faces.

Do not store this model in a high-temperature or humid area nor

under direct sunlight.

1

Safety Precautions

5

Do not operate the model on public roads, in crowded places

and near children. It may cause accidents.

Even when the power on the MINI-Z model is switched OFF, there is

still a low current flowing. In order to turn the power OFF completely,

all batteries must be removed from the model. If batteries are left

in the model, the batteries may overheat, ignite or leak.

Please remove all batteries after use.

Always turn power switch OFF and remove batteries when

removing

the body. Touching the circuit board and battery

terminals is dangerous.

Do not touch moving gears. They can cause injury.

1

6

During and after operation, the motor and batteries will be hot.

Do not touch them until they have had time to cool down.

Do not run your car in sandy, dusty, wet conditions, or on thick/soft

carpet. Such surfaces can damage its operating parts.

Do not use water, alcohol, or thinner to clean your car's body.

Simply wipe it down with a clean, soft cloth.

Do not install any option parts not made by Kyosho for this model.

To avoid causing irreparable damage, do not attempt any modifications.

Option Parts

1

Safety Precautions

Thinner

Alcohol

ページが読み込まれています...

8

*

*Chassis

Content

2

*Pinion Gear Set

(for replacement)

*Motor Spacer

*C-ring (Spare)

*Wheel Wrench

*Battery Holder

* *

*

*Pinion Tool

*

*Front Shock Stay *Rear Shock Stay (2-type)

*

*Deff.Lock Plate

*

*Wheel Nut (Spare)

*

*Pairing Stick

9

*PERFEX KT-18 Transmitter

(Controller)

*PERFEX KT-18

*Or, 2.4GHz ASF compatible transmitter

from Kyosho / Kondo Science Inc.

*

2.4GHz ASF

Equipments not included

*A Phillips Screwdriver (Precision type or a small sized)

*Wire Cutter

*Cutter

*

+ +

*4-AAA sized Alkaline Batteries or UM-4 sized

NiMH (Nickel-Metal Hydride) Batteries 4 pieces

Do not use any damaged batteries.

*4

4 4

*AAA sized or UM-4 sized Alkaline Batteries

*4

Damaged

Do not use Oxyride or other special type batteries.

*Body Set (Auto Scale Collection)

*

AAA

UM-4

4

3

10

Glossary of Main Parts

4

Chassis

Front Tire

Antenna

Pairing Button

Rear Tire

Rear Shock Unit

Front Shock Unit

Power Unit

Motor

Power Switch

Battery Holder

LED Indicator

I.C.S. Connector

ページが読み込まれています...

12

Before Operating

5

2x10mm

2x6mm

*Replace shock stays in accordance with the suspension shaft positions.

*

6

2 x 6mm

TP Screw

TP

4

2 x 10mm

TP Screw

TP

Front Rear

Suspension Shaft

4.8mm

Pillow Ball

4.8mm

Pillow Ball

C-ring

C

C-ring

C

Front Shock Stay Rear Shock Stay

Plastic Pencil Tip C-ring

C

Suspension Shaft

Adjustment of Wheelbase

Wheels and tires included with this set can be used with any body set.

If using the wheels and tires included with the body set, refer to the section 'Tires' in '8 Replacing Each Part'

and install accordingly.

13

Battery Installation

5

Battery Holder

AAA Batteries, Notice the polarity to be installed.

Battery Holder

4

To remove Battery Holder. To attach Battery Holder.

If it is not easy to remove the battery

holder, try with a flat blade screwdriver.

For installation of transmitter batteries, please refer to your transmitter's instruction manual.

14

Instructions from this point onwards relate to use with the PERFEX KT-18 transmitter.

If using a different transmitter, refer to the instructions included with your transmitter.

To use this transmitter with a previously purchased chassis (MINI-Z OVERLAND), it must undergo a pairing

adjustment.

Antenna

Pairing is the process of registering the transmitter's ID with your chassis. If you change transmitters, please

perform pairing. Pairing process is not required after the first time.

What is pairing?

< >How to complete pairing

Let's Drive!

6

Turn the Power Switch ON

15

1

LED Indicator

Push the mark side of the Throttle Trim and keep it down.

2

Push the power button to switch the transmitter ON.

Keep the mark pressed down, but release power button.

4

Once the LED indicator light has dimmed, the preparation of the transmitter is complete.

3

Confirm the LED is on. When the LED goes out after about 3 seconds, release finger from the Throttle Trim.

Pairing Button

6

Prepare pairing stick and locate the

LED indicator and pairing button.

Pairing Stick

OFFON

16

1

2

Chassis (Switch)

Use the pairing stick to push and hold

the pairing button.

5

Chassis (Switch)

4

3

Once the LED indicator comes on, stop pushing

the Pairing Button.

LED Indicator will show the following.

Light is ON : Pairing has been successful

Light is flashing : Pairing has not be completed.

Switch the transmitter and chassis

power off and do pairing again.

Let's Drive!

6

LED Indicator

17

6

Push the transmitter power button again and to turn it off.

Setting takes effect the next time power is turned on.

In rare cases, the pairing data may be lost. This is not

a malfunction. Simply repeat the pairing process.

If Pairing Failed

6

Someone else close by is pairing at the same time. Complete pairing at another time.

Another 2.4GHz device is being used close by. Stop using wireless LAN or Bluetooth devices.

Appliances such as a microwave oven are emitting

strong electrical waves are being used close by.

Stop using the electrical appliance.

Another radio control model using 2.4GHz is being used

close by.

Perform pairing in another location.

Attaching the Body.

Carefully spread the sides

of the body over the chassis

mounts.

2

1

2

OFFON

18

Antenna

Always turn the transmitter's power switch ON first!

Keep hands away from tires!

1

Push the power button to turn transmitter on.

2

Check that the LED indicator lights up.

Chassis (Switch)

When switched on, the transmitter finds open frequencies. Up to forty 2.4GHz Mini-Z Series models can be run

but may be lower if other 2.4GHz devices are being used. If no frequency can be found, LED will not light.

Operate in another location.

NOTE

< >For Normal Operation

1

2

Wheels may spin freely when power is turned on.

Let's Drive!

6

19

Throttle Trigger

Throttle Trim

Neutral

Raise the tires off the ground and check that all controls are responding.

With throttle trigger in neutral, click Throttle Trim one click at a time until car stops and continuous beep stops.

Adjustment not needed if car doesn't move. Beeping sound will start when neutral is found or range limit is reached.

If chassis is moving in reverse, click this button.

A

B

If chassis is moving forward, click this button.

B

Bringing the Car to a Complete Stop

Forward Reverse

6

20

Left

Right

Left

Neutral

Left Right

Steering Wheel

How to Control Your Model.

Basic Controls

Raise the tires off the ground and check

hat all controls are responding.

Throttle Trigger

Forward

Neutral

Reverse

Brake

Raise the tires off the ground and check that all controls are responding.

Forward Reverse

Let's Drive!

6

21

Reversing Point

Forward

Brake

Neutral

Reverse

6

22

Click Throttle Trim a few times until

tires move forward.

2

A

Click Throttle Trim a few times until tires

stop. Then click a few more times until beep

sound stops.

3

B

Click Throttle Trim 8 more times.

Adjustment is complete.

4

B

Check if a continuous beep sound is coming from the chassis.

If no sound Refer .

Problems with Reversing?

When Throttle Trigger is in neutral and the car hasn't stopped moving, follow the steps below to adjust neutral position.

1

2

Refer .

2

Refer .

3

Refer .

3

Refer .

4

Beep sound but car is moving forward.

Beep sound but car is moving backwards.

Throttle Trim

A

B

3

Let's Drive!

6

23

Steering Wheel Steering Trim

Neutral

With steering wheel in neutral, click the Steering Trim a few times so car runs in a straight line.

Use one click at a time. (Holding the button down does not work.)

If chassis moves left (L), click Steering Trim to adjust.

R

L R

RL

If chassis moves right (R), click Steering Trim to adjust.

R

L

When steering trim is in neutral or adjustment has reached the end of its range, beeping sound will start.

Due to effects from steering mechanism or surface, the car may not run perfectly straight. This is not abnormal.

L R

Running in a Straight Line

6

ページが読み込まれています...

Kyosho MINI-Z OVERLAND 取扱説明書

このマニュアルも適しています

Kyosho MINI-Z OVERLAND 取扱説明書

他の言語で

関連論文

その他のドキュメント