2. Kyosho
  3. Mini-Z Racer MR-03N RM Type

Kyosho Mini-Z Racer MR-03N RM Type, MZN112 MAZDA RX-7 FD3S ユーザーマニュアル

  • こんにちは！京商 ミニッツレーサー マツダ RX-7 FD3S ホワイトボディセットの組立説明書を読み終えました。シャシーの準備からボディの組立、取り付けまで、あらゆる質問にお答えできます。塗装方法や推奨パーツに関する質問も歓迎です！
  • ボディの塗装はいつ行いますか？
    推奨されるホイールとタイヤは何ですか？
    受信アンテナの加工は必要ですか？
    サイドステップの取り付けは必須ですか？
Before beginning assembly, please read these instructions thoroughly.
MZN112-T01
Side Body Mount (L)
Side Body Mount (R)
Body
Window Shield
R
THE FINEST RADIO CONTROL MODELS
INSTRUCTION SHEET
No.MZN112
90mm
Narrow
Tools : Must be prepared.
*Cutter Knife. *Nippers *Adhesive for plastic
*A Phillips Screwdriver
(Precision type or a small sized)
+ +
MAZDA RX-7 FD3S
For MINI-Z Racer MR-03N RM Type / MR-015 RM Type
White Body Set (Non Decoration)
2
For painting. use plastic model paints.
Attach each part as required.
Painting should be done before assembling.
Rear Mount Type (RM Type) Wheelbase (M)
1
Preparation of Chassis
Assemble the chassis as shown below.
Motor mounting position
Adjustment of Wheelbase / Front Tread
2
2 x 5mm
TP Screw
Replace the front body mount
with the one included in the set.
Front Body Mount
TP
Receiver Antenna
Bend the receiver antenna as shown below.
Receiver Antenna
2x5mm
Front body mount.
Chassis
Caution : Do not screw-in
excessively.
Antenna Cord
2mm
2x6mm
Caution : Do not screw-in
excessively.
< >
< Only for 27MHz >
30mm
Before beginning assembly, please read these instructions thoroughly.
MZN112-T01
Side Body Mount (L)
Side Body Mount (R)
Body
Window Shield
R
THE FINEST RADIO CONTROL MODELS
INSTRUCTION SHEET
No.MZN112
90mm
Narrow
Tools : Must be prepared.
*Cutter Knife. *Nippers *Adhesive for plastic
*A Phillips Screwdriver
(Precision type or a small sized)
+ +
MAZDA RX-7 FD3S
For MINI-Z Racer MR-03N RM Type / MR-015 RM Type
White Body Set (Non Decoration)
2
For painting. use plastic model paints.
Attach each part as required.
Painting should be done before assembling.
Rear Mount Type (RM Type) Wheelbase (M)
1
Preparation of Chassis
Assemble the chassis as shown below.
Motor mounting position
Adjustment of Wheelbase / Front Tread
2
2 x 5mm
TP Screw
Replace the front body mount
with the one included in the set.
Front Body Mount
TP
Receiver Antenna
Bend the receiver antenna as shown below.
Receiver Antenna
2x5mm
Front body mount.
Chassis
Caution : Do not screw-in
excessively.
Antenna Cord
2mm
2x6mm
Caution : Do not screw-in
excessively.
< >
< Only for 27MHz >
30mm
65471003-1 PRINTED IN CHINA
046-229-4115
13001900
243-0034 153
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
www.kyosho.com
www.mini-z.jp
3
© Copyright 2010 KYOSHO CORPORATION /
2
TP
Exhaust Pipe
Tail Lamp
L
Head Light Lens
(L)
L
Head Light (L) Open Type
R
Head Light Lens
(R)
R
Head Light (R) Open Type
Rear Wing
Rear Wing Base
Windshield Wiper
Side Skirt (L)
Put the side skirts according to your
preference. Cut away the pins before
glueing the side skirts.
Side Skirt (L)
TP Screw
TP Screw
TP Screw
L
Head Light (L) Closed Type
R
Head Light (R) Closed Type
Fog Light Lens
Fog Light Lens Cover (L)
Fog Light Lens Cover (R)
Fog Light Lens
You can choose open type
head lights according to
your taste.
The following wheels & tires are recommended.
No. Part Names
Body
Squeeze the chassis into
side body mounts.
Chassis
Insert front of chassis into
the front body mount holder.
Carefully spread the sides
of the body over the chassis.
Mount in orderly sequence.
4
< Only for 27MHz >
< 27MHz >
Put the receiver antenna
through the hole.
/