Yealink Yealink VC880 Full HD Video Conferencing System (CN,EN) V43.10 クイックスタートガイド
- タイプ
- クイックスタートガイド
Yealink VC880 Full HD Video Conferencing System Quick Start Guide
Applies to firmware version 63.43.0.10 or later
V43.10
Yealink Network Technology CO., LTD
English | 简体中文
We recommend that you use the accessories provided or approved by Yealink. The use of unapproved third-party accessories may result
in poor performance.
Put the magnet rings on the HDMI cable to prevent electromagnetic interference.
VCR11
Quick Reference Guide
1
Package Contents
1.8m
HDMI Cable×2
(for display device)
1.2m
HDMI Cable
(for content sharing)
1.2m
Mini-DP Cable
(for content sharing)
Cable Tie×5
VC880
Quick Start Guide
Power Adapter
3m
Ethernet Cable
0.8m
Ethernet Cable
7.5m
Ethernet Cable
AAA Battery×2
VC880 Codec
VCR11
Remote Control
VCH50
Video Conferencing Hub
Interface
Protective Cover
7.5m
Ethernet Cable
0.6m
USB Type-C Cable
(for content sharing)
VCH51
Quick Start Guide
0.6m
HDMI Cable
(for content sharing)
VCH51
Video Conferencing Hub
VCH50 Package
VCH51 Package
2
Connections
The system should be used with Yealink
original power adapter (48V/0.7A) only.
The use of the third-party power adapter
may damage the system. The cable should
be replaced at once if its skin is broken.
The system can connect up to 9 VCC22
video conferencing cameras.
VCC22 video conferencing cameras,
VCM34 video conferencing microphone
array, CTP20 collaboration touch panel,
PoE switch and Ethernet cables should be
purchased separately. In order to ensure
the best network signal, please purchase
UL certified CAT5E Ethernet cables and
recommended PoE switch. The maximum
length of each Ethernet cable is 100
meters. Contact the agents or hotline
support to get the recommended PoE
switch models.
If you do not need wired sharing,
VCH50/VCH51 video conferencing hub is
unnecessary.
Third-party camera
RCA Cable
HDMI Cable
VCH50
PC
MINI DP HDMI
Codec
Audio
VCC22 VCC22 VCC22
...
Camera
VCC22
IEEE 802.3af compliant
PoE Switch
Display×2
1.8m
HDMI Cable
3m
Ethernet Cable
Power Adapter
0.6m
USB Type-C Cable or
0.6m
HDMI Cable
7.5m
Ethernet Cable
Ethernet Cable
Ethernet Cable
Mixer
CTP20
VCM34
VCM34
PoE
PoE
If endpoint works with VCH50, do the following:
...
Camera
VCC22
IEEE 802.3af
compliant PoE Switch
CTP20
VCM34
VCM34
PoE
PoE
HDMI
PC
PoE
0.6m
HDMI Cable
0.6m USB
Type-C Cable
or
PC
If endpoint works with VCH51, do the following:
Third-party camera
RCA Cable
HDMI Cable
Display×2
1.8m
HDMI Cable
3m
Ethernet Cable
Power Adapter
Mixer
Ethernet Cable
VCC22 VCC22 VCC22
7.5m
Ethernet Cable
Ethernet Cable
3
VCH51
4
Network Environment
Bandwidth Requirements
Both downlink bandwidth and uplink bandwidth should meet above requirements.
The bandwidth mentioned above is based on a two-way call. Bandwidth in head office should be increased along with the
growing number of connected branch offices.
Network Deployment
Choose Cloud deployment or traditional deployment according to your need.
Video Resolution Recommended Bandwidth
Full HD 1080P 1.3Mb
People 1080P+Content 1080P 2.6Mb
Remote Control and Cable Ties Installation
Cloud Deployment
Cloud deployment does not need complex network settings. You only need to get account information from your system
administrator, and log into video conference platform.
Do the following to log into video conference platform via remote control:
1. Select More->Setting->Advanced (Default Admin Password:0000)->Video Conference Platform.
2. In the Cloud Account field, check the Enabled checkbox.
3. Select the desired platform from the pull-down list of Platform Type.
4. Configure the desired platform and log in.
Traditional Deployment
If you deploy the system in the head office, make sure it is reachable from public network.
If you deploy the system in the branch office, use intelligent traversal to deploy it or just follow the same steps as for the head
office.
Head Office
If you deploy the system in the head office, at least one static public IP address is required to allow branch offices to connect.
Do one of the following to deploy the system:
Option1: Assign a static public IP address to your system.
Option2: If you deploy the system in an Intranet (behind the firewall), assign a static private IP address to it and do port mapping
on the firewall.
Configure a Static IP Address
The following introduces how to use the remote control to configure a static IPv4 address:
1. Select More->Setting->Advanced (Default Admin Password: 0000)->Wired Network.
2. Select IPv4 from the pull-down list of IP Mode.
3. Select IPv4 , and then press OK key.
5
6
4. Uncheck the DHCP checkbox.
5. Enter the IP address, subnet mask, gateway and DNS information in corresponding fields.
6. Save the change.
The display device prompts “Reboot now?”
.
7. Select
OK
to reboot the
system.
Configure Port Mapping
If you deploye system in an Intranet, you must forward the following ports to the public network on the firewall, so that your
system can receive a public-to-private call.
Branch Office
If you deploy the system in the branch office, do one of the following to deploy it:
Option1: Deploy the system following the same steps as for the head office. In this way, both inbound and outbound
calls are available.
Option2: Deploy the system using intelligent traversal. You only need to assign a private IP address to your system.
Make sure this private IP address can access the public network. Only outbound calls are available when using this
method.
PortFunction
H.323 signal port
SIP optional
Audio & Video media stream port
Web management port optional
Protocol Type
UDP/TCP
5060-5061
443
50000-51000
1719-1720
TCP/UDP
TCP/UDP
TCP
7
When you use intelligent traversal to deploy your system, you have to open following ports on your firewall if they are restricted.
It is recommended that you forward the web management port(443/TCP) to the public network, so that the head office can remotely
manage the branch office.
Troubleshooting
Testing Connectivity
After installation and deployment, you can test the system by dialing the Yealink Demo Room (117.28.251.50 or
117.28.234.45). If you can’t dial out successfully, please contact your IT administrator to check the network.
Configuring Static NAT
If you do not use Cloud platform and deploy your system in an Intranet, you have configured port mapping on the firewall or
gateway, but you find that local system appears black screen and you cannot hear sound when you call Yealink Demo or
other systems. The most likely reason is that the firewall or gateway in your environment does not support the ALG feature.
In this situation, please enable static NAT feature on the system to solve this problem.
To configure static NAT via the remote control:
1. Select More->Setting->Advanced (Default Admin Password:0000)->NAT/Firewall.
2. Select Auto from the pull-down list of Type, the system will obtain public IP address automatically.
3. If the system does not obtain a public IP address automatically, select Manual Settings from the pull-down list of Type,
and then enter the public IP address in the Public IP Address field.
4. Save the change.
PortFunction
H.323 signal port
SIP optional
Audio & Video media stream port
Protocol Type
UDP/TCP
TCP/UDP
TCP/UDP
50000-51000
1719-1720
5060-5061
我们推荐使用由Yealink提供或经Yealink认可的配件和线缆，使用未经认可的第三方配件和线缆可能会导致性能的下降。
使用HDMI线前，请套上磁环用于抗电磁干扰。
包装清单
电源适配器
VC880主机 VCR11遥控器
0.8米网线
3米网线
7.5米网线
7号电池 2
+
束线带 x5
VCR11使用说明单页
VC880快速入门指南
1.2米Mini-DP线
（用于分享辅流）
1.2米HDMI线
（用于分享辅流）
1.8米HDMI线x 2
（用于接显示设备）
8
VCH50接线盒
接口保护罩
VCH51
快速入门指南
0.6米USB Type-C线
（用于分享辅流）
VCH50有线辅流
VCH51有线辅流
7.5米网线
VCH51接线盒
0.6米HDMI线
（用于分享辅流）
9
电源适配器
3米网线
第三方摄像机 调音台
IEEE 802.3af 标准
PoE交换机
7.5米网线
显示设备x2
1.8米HDMI线
RCA音频线 HDMI线
VCH50
MINI DP HDMI
Codec
Audio
入网口
VCC22视频会议摄像机
...
Camera
网线
网线
连接终端
我们要求使用Yealink原装电源（48V/0.7A），
使用第三方电源可能会导致终端损坏。如果
使用过程中发现线缆破皮，请立即更换。
终端最多可连接9台VCC22视频会议摄像机。
只连接一台VCC22视频会议摄像机时，你可
以将VCC22的Camera口直接连在VCH50接
线盒的Audio接口上。
VCC22视频会议摄像机、PoE交换机、
VCM34可级联阵列麦克风、CTP20协作触控
平板，相关网线和PoE交换机需要另外购买。
为确保最佳的网络信号，请购买通过UL认证
的CAT5E网线及亿联推荐的PoE交换机。每
根网线的长度最大可支持100米。亿联推荐
的PoE交换机型号，请联系代理商或拨打技
术支持热线咨询技术人员。
如果你无需使用VCH50/VCH51进行演示，
可以不用连接VCH50/VCH51接线盒。
PC
1.2米Mini-DP线 或 1.2米HDMI线
VCC22 VCC22 VCC22
CTP20
VCM34
VCM34
PoE
PoE
如果终端搭配VCH50使用，请按下图完成连接：
10
电源适配器
3米网线
第三方摄像机 调音台
显示设备x2
1.8米HDMI线
RCA音频线 HDMI线
如果终端搭配VCH51使用，请按下图完成连接：
...
Camera
CTP20
VCM34
VCM34
PoE
PoE
HDMI
PC
PoE
PC
VCC22 VCC22 VCC22
IEEE 802.3af 标准
PoE交换机
0.6米
USB Type-C线 或 0.6米HDMI线
VCC22视频会议摄像机
网线
入网口
7.5米网线
VCH51
网线
11
视频会议室的部署可分为如下几个模块：光线、摄像机放置、拾音/声音播放、画面显示、接线。以下是针对这些模块的具体建议，在会议室装修与
视频会议设备部署的过程中可参考以下内容取得更佳的视频会议效果。
视频会议室部署
光线
会议室的灯光应更多地聚焦在会议桌与参会人的位置，以 45° 斜照向参会人面部是较
为理想的光照条件。
如会议室原有的光线不足可考虑加装平面光源，色温以4000~5000k，光照强度以
300~500lux为宜。光线充足与否可以视频画面中面部肤色是否真实还原作为评判标
准。
即使会议室采光条件良好，也建议在会议过程中打开会议室灯光，以确保会议桌与参
会人区域有充足且均匀的光照度。
摄像头避免正对强光源，例如窗户。以免出现人物图像逆光现象。如果摄像头不可避免
地朝向窗口，可装配窗帘。
安装遥控器电池 使用束线带
45
。
摄像机放置
根据实际的会议室情况，摄像头安装高度建议在 1.55~1.85 米之间。如果是较大型的会
议室/会场则不受限于此建议高度，可根据被摄物体距离确定摄像头高度。
建议将摄像头放置于电视顶部水平居中的位置。如果显示设备较大（大于80寸）或应用
了拼接屏，可考虑将摄像头固定在显示设备下方，但应高于会议桌高度。
为提升视频会议中的眼神交流与互动感，尽可能将摄像头靠近显示对方视频画面的屏
幕。
投影+电视作为显示设备的情况下，将电视架推车尽可能靠近投影幕布，摄像头放置于
电视上靠近投影幕布的一侧。
面积较大的会议室/会场可考虑吊顶倒装摄像头，但需避免摄像头直接安装于天花板推
荐使用吊架降低摄像头高度。需注意摄像头高度/角度调节范围相对第一排参会者距离
的关系。以摄像头离地 2.5m 为例，第一排参会者与摄像头的距离应至少 2m为宜。
如需多角度画面或更广的视角范围，可选购扩展摄像头 VCC22。
1.5 (m)
参会者与麦克风的距离在0.5~1.5m范围内可获得最佳的拾音效果。
当会议室面积大于50㎡或会议桌长于4m时建议配备扩展麦克风或采用多个麦克
风。
会议电话的内置扬声器通常能够满足60㎡以下会议室的需求。当会议室面积大于
60㎡时可考虑级联会议电话或连接外部音响，确保声音有效覆盖所有参会人。
如使用电视扬声器播放声音，将电视音量调整到合适的大小，避免音量过大出现破
音。麦克风应与电视保持一定距离，建议大于2m。
拾音/声音播放
1.55 (m)
1.85 (m)
12
13
因投影仪的显示效果相对较差且容易受到光照情况影响，所以建议使用液晶电视作
为视频会议的显示设备。如需同时使用电视和投影仪，尽可能将电视放置在靠近投影
仪的位置，减少视线跨度。
由于投影效果易受光照情况影响，在使用投影仪时应尽可能减少照射向投影幕的灯
光，增加参会者区域的光照度。
如果使用辅流的需求较多，建议使用双屏显示，如此可同时全屏观看视频画面与辅流
内 容 。
画面显示
线材
尽可能选择具备线材收纳功能的会议桌，以确保桌面整洁。
如果会议室未进行走线设计，电视至桌面的线材可使用金属线槽贴地走线。
遇到线长不够需要更换线材或需要转接的情况，请联系代理商或拨打技术支持热线
咨询技术人员确定线材规格，避免自行配线影响使用效果，甚至造成不必要的损失。
电视
电视 电视
14
网络快速部署
网络带宽需求
终端所需网络带宽需求为上下行带宽需求，网络的上行带宽及下行带宽均需要满足需求
以上带宽需求为两方通话的带宽需求，主会场带宽需要根据分会场数量进行相应的增加
网络部署
你可以使用云服务方式或传统方式部署终端。
云服务方式部署
云服务方式部署无需复杂的网络配置，登录云平台就可以实现各会场间的互联互通。账号信息请从管理员处获取。
通过遥控器登录平台：
1. 选择更多->设置->高级设置（默认密码：0000）->视频会议服务平台。
2. 勾选启用云功能复选框。
3. 从登录平台下拉框中选择你想要登录的平台。
4. 填写平台登录的相关信息并登录。
全高清视频1080P 1.3Mb
2.6Mb人像1080P+内容1080P
建议带宽需求
视频分辨率
15
传统方式部署
请根据你的会场所处的角色进行设置，主会场必须公网可达，分会场可参考主会场设置或采用智能穿透方式部署。
部署主会场
如果将终端部署在主会场，则它必须至少拥有一个固定公网IP地址，以便其它终端可以通过网络访问到你的终端，你可以
任选以下一种方式部署主会场：
选项一
：如果你将终端直接部署在公网，请为其设置一个固定的公网IP地址。
选项二
：如果你将终端部署在内网(防火墙后)，除了为其设置一个固定的内网IP地址之外，还需要在防火墙上设置端口
映射。
设置固定IP地址
以下介绍如何通过遥控器为终端配置一个固定的IPv4地址：
1. 选择
更多->
设置->高级设置（默认密码：0000）->有线网络。
2. 从IP模式下拉框中选择IPv4。
3. 按遥控器的上下方向键选择
IPv4
，再按OK键。
4. 取消勾选
DHCP
复选框 。
5. 在相应的区域中输入：IP地址、子网掩码、网关、DNS主服务器和DNS备份服务器。
6. 按遥控器的上下方向键选择保存，再按OK键。
显示器的液晶屏幕提示【需要重启系统使配置生效，是否立即重启？】
7. 选择确认重启终端。
设置端口映射
如果你将终端部署在内网，您需要在防火墙上将以下端口映射至公网。终端才可以正常接听来自公网的呼叫：
部署分会场
如果将终端部署在分会场，你可以任选以下一种方式部署分会场：
选项一
：分会场可以采用与主会场相同的部署方式。使用该种方式时终端可呼入、可呼出。
选项二
：采用智能穿透方式进行部署，仅需为终端分配一个可访问公网的IP地址即可。使用该种方式时终端只能呼出不
能呼入。
1719-1720
5060-5061
50000-51000
443
UDP/TCP
TCP/UDP
TCP/UDP
TCP
H.323 信令端口
SIP信令端口（可选）
音视频媒体流端口
网页管理端口（可选）
描述 端口 类型
采用智能穿透方式部署时，如果你的网络有端口限制，需要开放以下端口权限
建议分会场将网页管理端口（443/TCP）映射至公网，以便主会场可以远程管理、支持分会场
1719-1720
5060-5061
50000-51000
UDP/TCP
TCP/UDP
TCP/UDP
H.323 信令端口
SIP信令端口（可选）
音视频媒体流端口
描述 端口 类型
16
17
故障排查
连通性测试
完成终端的安装部署后，你可以拨打Yealink Demo环境（117.28.251.50、117.28.234.45）来测试终端是否工作正
常，如果无法呼通Demo环境，请联系网络管理员检查你的内部网络是否通畅。
配置静态NAT功能
如果你将终端部署在内网(防火墙后)，并且已在防火墙或网关上配置了端口映射，当跨公网呼叫其他会场的终端或
Yealink Demo时, 本地出现黑屏无声的问题，极有可能是因为本会场网络环境中的防火墙或者网关不支持ALG功
能。要解决这个问题，请使用遥控器开启终端上的静态NAT功能：
1. 选择
更多->
设置->高级设置（默认密码：0000）->NAT/防火墙。
2. 从类型下拉框中选择自动，终端将自动获取当前网络的公网IP地址。
3. 如果终端未能自动获取到公网IP地址，你可以在类型下拉框中选择手动设置，然后在公网IP地址区域输入当
前网络的公网IP地址。
4. 按遥控器的上下方向键选择保存，再按OK键保存当前配置。
Regulatory Notices
Operating Ambient Temperatures
Operating temperature: +32 to 104°F (0 to 40°C)
Relative humidity: 5% to 90%, noncondensing
Storage temperature: -22 to +160°F (-30 to +70°C)
Warranty
Our product warranty is limited only to the unit itself, when used normally
in accordance with the operating instructions and the system environment.
We are not liable for damage or loss resulting from the use of this product,
or for any claim from a third party. We are not liable for problems with
Yealink device arising from the use of this product; we are not liable for
financial damages, lost profits, claims from third parties, etc., arising from
the use of this product.
Explanation of the symbols
DC symbol
is the DC voltage symbol.
WEEE Warning symbol
To avoid the potential effects on the environment and human health
as a result of the presence of hazardous substances in electrical and
electronic equipment, end users of electrical and electronic
equipment should understand the meaning of the crossed-out wheeled bin
symbol. Do not dispose of WEEE as unsorted municipal waste and have to
collect such WEEE separately.
Restriction of Hazardous Substances Directive (RoHS)
This device complies with the requirements of the EU RoHS Directive.
Statements of compliance can be obtained by contacting [email protected].
Safety Instructions
Save these instructions. Read these safety instructions before use!
General Requirements
Before you install and use the device, read the safety instructions
carefully and observe the situation during operation.
During the process of storage, transportation, and operation, please
always keep the device dry and clean, avoid collision and crash.
Please attempt not to dismantle the device by yourself. In case of any
discrepancy, please contact the appointed maintenance center for repair.
Please refer to the relevant laws and statutes while using the device.
Legal rights of others should be respected as well.
Environmental Requirements
Place the device at a well-ventilated place. Do not expose the device
under direct sunlight.
Keep the device dry and free of dusts.
Do not place the device on or near any inflammable or fire-vulnerable
object, such as rubber-made materials.
Keep the device away from any heat source or bare fire, such as a candle
or an electric heater.
Operating Requirements
Do not let a child operate the device without guidance.
Do not let a child play with the device or any accessory in case of
accidental swallowing.
Please use the accessories provided or authorized by the manufacturer
only.
The power supply of the device shall meet the requirements of the input
voltage of the device. Please use the provided surge protection power
socket only.
Before plugging or unplugging any cable, make sure that your hands are
completely dry.
Do not spill liquid of any kind on the product or use the equipment near
water, for example, near a bathtub, washbowl, kitchen sink, wet
basement or near a swimming pool.
During a thunderstorm, stop using the device and disconnect it from the
power supply. Unplug the power plug and the Asymmetric Digital
Subscriber Line (ADSL) twisted pair (the radio frequency cable) to avoid
lightning strike.
If the device is left unused for a rather long time, disconnect it from the
power supply and unplug the power plug.
When there is smoke emitted from the device, or some abnormal noise
or smell, disconnect the device from the power supply, and unplug the
power plug immediately.
Contact the specified maintenance center for repair.
Do not insert any object into equipment slots that is not part of the
product or auxiliary product.
Before connecting a cable, connect the grounding cable of the device
first. Do not disconnect the grounding cable until you disconnect all other
cables.
Cleaning Requirements
Before cleaning the device, disconnect it from the power supply.
Use a piece of soft, dry and anti-static cloth to clean the device.
Keep the power plug clean and dry.
VC880- EN+CN
Troubleshooting
The unit cannot supply power to device other than Yealink device.
There is a bad connection with the plug.
1. Clean the plug with a dry cloth.
2. Connect it to another wall outlet.
The usage environment is out of operating temperature range.
1. Use in the operating temperature range.
The cable between the unit and the Yealink device is connected incorrectly.
1. Connect the cable correctly.
You cannot connect the cable properly.
1. You may have connected a wrong Yealink device.
2. Use the correct power supply.
Some dust, etc., may be in the port.
1. Clean the port.
Contact your dealer or authorized service facility for any further questions.
FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
IC Statement
This device complies with Industry Canada’s licence-exempt RSSs. Operation is
subject to the following two conditions:
(1) this device may not cause interference; and
(2) this device must accept any interference, including interference that may
cause undesired operation of the device. CAN ICES-3(B)
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux
appareils radio exempts de licence. L’exploitation est autorisée aux deux
conditions suivantes :
(1) l’appareil ne doit pas produire de brouillage;
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d’en compromettre le
fonctionnement.NMB-3(B)
Contact Information
YEALINK NETWORK TECHNOLOGY CO.,LTD.
309, 3rd Floor, No.16, Yun Ding North Road, Huli District, Xiamen City, Fujian, P.R. China
YEALINK (EUROPE) NETWORK TECHNOLOGY B.V.
Strawinskylaan 3127, Atrium Building, 8th floor, 1077ZX Amsterdam, The Netherlands
YEALINK (USA) NETWORK TECHNOLOGY CO., LTD.
999 Peachtree Street Suite 2300, Fulton, Atlanta, GA, 30309, USA
Made in China
About Yealink
Yealink is a global leading provider of enterprise communication and collaboration solutions, offering video conferencing service to worldwide
enterprises. Focusing on research and development, Yealink also insists on innovation and creation. With the outstanding technical patents of
cloud computing, audio, video and image processing technology, Yealink has built up a panoramic collaboration solution of audio and video
conferencing by merging its cloud services with a series of endpoints products. As one of the best providers in more than 140 countries and
regions including the US, the UK and Australia, Yealink ranks No.1 in the global market share of SIP phones shipments.
Technical Support
Visit Yealink WIKI (http://support.yealink.com/) for the latest firmware, guides, FAQ, Product documents, and more. For better service, we
sincerely recommend you to use Yealink Ticketing system (https://ticket.yealink.com) to submit all your technical issues.
YEALINK(XIAMEN) NETWORK TECHNOLOGY CO.,LTD.
Web: www.yealink.com
Copyright
©2020
YEALINK(XIAMEN) NETWORK
TECHNOLOGY CO.,LTD
.All rights reserved.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
Yealink Yealink VC880 Full HD Video Conferencing System (CN,EN) V43.10 クイックスタートガイド
- タイプ
- クイックスタートガイド
他の言語で
関連論文
-
Yealink Yealink VC800 Full HD Video Conferencing System (CN,EN) V43.10 クイックスタートガイド
-
-
-
-
-
-
-
-
-
Yealink RingCentral A20 ユーザーガイド