Yealink VC800 Full HD Video Conferencing System 中英 V40.10 クイックスタートガイド

Yealink VC800 Full HD Video Conferencing System Quick Start Guide

Applies to firmware version 63.40.0.10 or later

V40.10

Yealink Network Technology CO., LTD

English | 简体中文

3m

Ethernet Cable

AAA Battery×2

VC800

Quick Start Guide

Mounting Bracket

and Accessories

Package Contents

VC800 Codec

2

We recommend that you use the accessories provided or approved by Yealink. The use of unapproved third-party accessories may

result in reduced performance.

VC800 endpoint canwork with Wired Sharing package or Wireless Sharing package for sharing content.

VCR11

Remote Control

OK

Cable Tie×5

Power Adapter

Velcro×2

VESA Accessory

Put the magnet rings on the HDMI cable to prevent electromagnetic interference.

(One Velcro is on the bracket)

1

Acrylic board

1.8m

HDMI Cable×2

(for thedisplay device)

1

System Installation

Select one of the following installation methods based on your site requirements:

Put on a Flat Surface

Mount on top of a TV

Mount on a wall

Mount on a ceiling

Mount onto a TV stand or a tripod

.

VCH50 Video

Conferencing Hub

1.2m

Mini-DP Cable

0.5 m

Ethernet Cable

1.2m

HDMI Cable

(for content sharing)

7.5m

Ethernet Cable

Wired Sharing Package

WPP20 Quick Start Guide

WPP20 Wireless

Presentation Pod

Wireless Sharing Package

Wi-Fi USB Dongle WF50

WF50 User Guide

CTP20 Touch Pen Battery

1m

USB Cable

CTP20

Quick Start Guide

Pen Holder

VCM34×2 Silicone Pad ×2

VCM34

Quick Start Guide

3m

Ethernet Cable ×2

7.5m

Ethernet Cable

Steps：

1

3

2

4

3

Open the baffle.

Push the bracket along the track of the V800 codec.

Remove one Velcro.

Put the bracket on the top of the TV.

Stick a Velcro onto the back of the TV, and make sure that the bracket and the back of the TV are tightly positioned against each

other.

TV

5

4

5

Pay attention to the direction of the bracket

Mount on top of a TV

Put on a Flat Surface

You can put the system on a conference room table, and make sure that the slope is not more than 15 degrees so that the system

can operate correctly.

Please choose the following installation method when the thickness of the TV is between 50mm and 100 mm.

TV

5

6

4

3

2

1

2

3

1

Pay attention to the direction of the bracket

If your system cannot be mounted on the top of a TV when the bracket has

reached the given location, remove the bracket, and then convert its direction.

Refer to the following section for more information.

2

The system may fall down when the thickness of the TV is more than 100 mm. In this situation, do not mount the system on the

top of a TV.

Please choose the following installation method when the thickness of the TV is between 16mm and 55mm.

Steps：

1

3

2

4

3

Open the baffle.

Push the bracket along the track of the system.

Stick a Velcro onto the bracket.

Remove one Velcro.

Put the bracket on the top of the TV.

Stick a Velcro onto the back of the TV, and make sure that the bracket and the back of the TV are tightly positioned against

each other.

5

6

Do not pick up the bracket which connects

with a system, the system may

fall down in this situation.

48mm

Hole diameter: 6mm

Hole depth: 30mm

Screw specification: T4×30

Mount on a Wall

2

1

The recommended height is 1.55m-1.85m above the ground.

X

If your system cannot be mounted on the top of a TV

when the bracket has reached the given location, you

should choose other installation methods.

3

Steps：

1

2

3

4

Punch holes into the wall and then insert the expansion bolts.

Secure the bracket using the T4×30 screws.

Push the system along the track of the bracket.

Secure the system onto the bracket using the M3×8 screws.

3

4

Screw specification: M3×8

Mount on a Ceiling

.

14.0mm

0.55in.

62.5mm

(2.46in.)

Screw hole

6.0 mm(0.24 in.) in depth

Location hole

5.0 mm(0.20 in.) in diameter

4

If you choose the ceiling-mounted installation, you need to purchase a bracket separately. The bracket must meet the following

requirements:

Able to bear the weight of at least 10.5kg (23.15 lb.) and the thickness must be between 2mm (0.08 in.) and 3 mm (0.12 in.).

Comes with a location pillar, which can be inserted into the location hole of the VESA accessory.

The distance between the screw on the bracket and the location pillar must be 14 mm (0.55 in.).

5

1 2

Screw specification: M3×8

Remote Control and Cable Ties Installation

3

Screw specification: M3×8

1

2

3

Push the VESA accessory along the track of the system.

Secure the VESA accessory to the system using the M3×8 screws.

Align the location pillar at the location hole, and then secure the bracket to the VESA accessory using the 1/4”-20 UNC screw.

TV Stand

Mount onto a TV Stand or a Tripod

You need to purchase a TV stand or a tripod separately. The TV stand or tripod has the same requirements as the backet used in the

ceiling-mounted installation method.

The installation steps are the same as the ceiling-mounted installation steps.

Steps：

1

2

3

Screw specification:

1/4”-20 UNC

Screw specification:

1/4”-20 UNC

Connections

Power Adapter

Display×2

1.8m

HDMI Cable

3m

Ethernet Cable

7.5m

Ethernet Cable

6

The system should be used with Yealink original power adapter (48V/0.7A) only. The use of the third-party power adapter may

cause the damage to the system. The cable should be replaced at once if its skin is broken.

MINI DP HDMI

Codec

3m

Ethernet Cable

Audio

3m

Ethernet Cable

VCM34

PoE

CTP20

7.5m

Ethernet Cable

VCH50

MINI DP HDMI

Codec

Audio

Wired Sharing

VC Hub/Phone port

on VC800 codec

7.5m

Ethernet Cable

1.2m

HDMI Cable

1.2m

Mini-DP Cable or

PC

PoE

If you do not need the VCH50 video conferencing hub to share content, you can connect the VC Hub/Phone port on the system to the

PoE port on the VCM34 directly.

7

Wireless Sharing

Network Environment

Bandwidth Requirements

Both downlink bandwidth and uplink bandwidth should meet above requirements.

The bandwidth mentioned above is based on a two-way call. Bandwidth in head office should be increased along with the growing

number of connected branch offices.

Network Deployment

Choose Cloud deployment or traditional deployment according to your need.

Cloud Deployment

Cloud deployment does not need complex network settings. You only need to get account information from your system administrator, and

log into video conference platform.

Do the following to log into video conference platform via remote control:

1. Select More->Setting->Advanced (Default Admin Password:0000)->Video Conference Platform.

2. In the Cloud Account field, check the Enabled checkbox.

3. Select the desired platform from the pull-down list of Platform Type.

4. Configure the desired platform and log in.

Video Resolution Recommended Bandwidth

Full HD 1080P 1.3Mb

People 1080P+Content 1080P 2.6Mb

WPP20 Wireless Presentation Pod WF50 Wi-Fi USB Dongle

PC

For more information on WPP20 wireless presentation pod, refer to Yealink WPP20 Wireless Presentation

Pod Quick Start Guide.

Traditional Deployment

If you deploy the system in the head office, make sure it is reachable from public network.

If you deploy the system in the branch office, use intelligent traversal to deploy it or just follow the same steps as for the head office.

Head Office

If you deploy the system in the head office, at least one static public IP address is required to allow branch offices to connect.

Do one of the following to deploy the system:

Option1: Assign a static public IP address to your system.

Option2: If you deploy the system in an Intranet (behind the firewall), assign a static private IP address to it and do port mapping on the firew all.

8

Configure a Static IP

The following introduces how to use the remote control to configure a static IPv4 address:

1. Select More->Setting->Advanced (Default Admin Password:0000)->Wired Network.

2. Select IPv4 from the pull-down list of IP Mode.

3. Select IPv4, and then press OK key.

4. Uncheck the DHCP checkbox.

5. Enter the IP address, subnet mask, gateway and DNS information in corresponding fields.

6. Save the change.

The display device prompts “Reboot now?”

.

7. Select

OK

to reboot the

system.

Configure Port Mapping

If you deploye system in an Intranet, you must forward the following ports to the public network on the firewall, so that your system can

receive a public-to-private call.

Branch Office

If you deploy system in the branch office, do one of the following to deploy it:

Option1: Deploy the system following the same steps as for the head office. In this way, both inbound and outbound calls are available.

Option2: Deploy the system using intelligent traversal. You only need to assign a private IP address to your system. Make sure this

private IP address can access the public network. Only outbound calls are available when using this method.

When you use intelligent traversal to deploy your system, you have to open following ports on your firewall if they are restricted.

It is recommended that you forward the web management port(443/TCP) to the public network, so that the head office can remotely

manage the branch office.

PortFunction

H.323 signal port

SIP optional

Audio & Video media stream port

Web management port optional

Protocol Type

UDP/TCP

5060-5061

443

50000-51000

1719-1720

TCP/UDP

TCP

PortFunction

H.323 signal port

SIP optional

Audio & Video media stream port

Protocol Type

UDP/TCP

TCP/UDP

50000-51000

5060-5061

1719-1720

Troubleshooting

Testing Connectivity

After installation and deployment, you can test the system by dialing the Yealink Demo Room (117.28.251.50 or 117.28.234.45). If you can’t dial

out successfully, please contact your IT administrator to check the network.

Configuring Static NAT

If you do not use Cloud platform and deploy your system in an Intranet, you have configured port mapping on the firewall or gateway, but you

find that local system appears black screen and you cannot hear sound when you call Yealink Demo or other systems. The most likely reason is

that the firewall or gateway in your environment does not support the ALG feature. In this situation, please take the following actions so that the

static NAT feature on the system can solve this problem.

To configure static NAT via the remote control:

1. Select More->Setting->Advanced (Default Admin Password:0000)->NAT/Firewall.

2. Select Auto from the pull-down list of Type, the system will obtain public IP address automatically.

3. If the system does not obtain a public IP address automatically, select Manual Settings from the pull-down list of Type, and then enter

the public IP address in the Public IP Address field.

4. Save the change.

9

此为A级产品。在生活环境中，该产品可能会造成无线电干扰。在这种情况下，可能需要用户对干扰采取切实可行的措施。

我们推荐使用由Yealink提供或经Yealink认可的配件和线缆，使用未经认可的第三方配件和线缆可能会导致性能的下降。

你可以选择有线辅流或无线辅流套件进行内容共享。

VC800主机可搭配CTP20与VCM34套件或会议电话套件使用。

使用HDMI线前，请套上磁环用于抗电磁干扰。

10

安装终端

你可以根据实际需要选择安装终端的方式：

将终端摆放在水平桌面。如果桌面略有倾斜，请保证倾斜角小于15°，以保证终端的摄像机云台正常运转。

平放安装

包装清单

OK

2

1

VCR11遥控器

VCH50接线盒

7号电池x2

VC800主机

亚克力牌

电源适配器

1.8米HDMI线x 2

（用于接显示设备）

1.2米Mini-DP线

（用于分享辅流）

0.5米网线

7.5米网线

VESA配件

支架配件

（用于安装主机）

魔术贴x2

（一套已贴在支架上）

会议电话套件

CP960会议电话

CPE90有线扩展麦x2

1.2米HDMI线

（用于分享辅流）

束线带x 5

3米网线

VC800

快速入门指南

VC800

最佳部署实践方案

CTP20

VCM34x2

有线辅流套件

WPP20 无线传屏助手

USB无线网络适配器WF50

WF50用户指南

WPP20快速入门指南

无线辅流套件

CTP20与VCM34套件

可选配件

11

当电视厚度范围为50mm-100mm时，进行以下步骤：

步骤：

1

3

2

4

3

打开终端底部的挡板。

将支架沿着终端底部轨道推至合适的位置。

撕开支架上的魔术贴。

将支架挂在电视的上方。

在电视背部黏贴魔术贴（魔术贴为一次性，黏贴前注意清洁电视背后），调整支架，使支架和电视的背面完全紧贴。

5

4

5

6

电视

2

3

1

注意支架的方向

槽位边缘

当支架与箭头位置齐平，还不能放置在电视顶上时，请取出支架反向装

配。请参阅下文了解更多信息。

挂装

当电视厚度范围为16-55mm时，进行以下步骤：

5

4

3

电视

1

注意支架的方向

2

请勿手持支架拿起终端，有掉落风险。

步骤：

1

3

2

4

3

打开终端底部的挡板。

将支架沿着终端底部轨道推至合适的位置。

在支架上黏贴魔术贴（魔术贴为一次性，黏贴前注意清洁支架）。

撕开支架上的魔术贴。

将支架挂在电视的上方。

在电视背部黏贴魔术贴（魔术贴为一次性，黏贴前注意清洁电视背后），调整支架，使支架和电视的背面完全紧贴。

5

6

当支架与底壳箭头位置齐平，还不能放置在电视顶上

时，请使用其他安装方式。

电视厚度超过100mm时，请勿使用挂装方式，机器

有跌落风险。

X

48mm

墙装

你可以用支架将终端安装在墙上，终端安装高度建议范围为1.55-1.85m。

打孔直径： 6mm

打孔深度： 30mm

螺丝规格：T4x30

12

2

1

3

螺丝规格：M3x8

1

3

2

4

3

在墙上打孔，将膨胀螺栓固定至墙上。

用T4×30型号的螺丝将支架固定到墙上。

将终端底部沿着支架的轨道往里推。

用两个M3×8型号螺丝将终端锁在支架上。

步骤：

4

13

吊装

1

3

2

3

将VESA配件沿着终端底部轨道往里推。

使用两个M3×8型号螺丝将VESA配件锁到终端上。

将支架自带的定位柱对准VESA配件的定位孔，并将1/4”-20UNC英制螺钉旋进VESA配件的螺丝孔。

步骤：

1 2

螺丝规格：M3x8

14.0mm 62.5mm

螺丝孔

深度：6.0mm

定位孔

直径：5.0mm

3

你可以自行选购支架来将终端倒挂在天花板上，选购的支架必须满足以下条件：

承重至少为10.5kg，厚度建议为2mm-3mm。

支架配套一个定位柱，定位柱用来插入VESA配件的定位孔中。

支架上的英制螺钉和定位柱的直线距离必须为14mm。

.

螺丝规格：

1/4-20UNC英制螺钉

14

螺丝规格：M3x8

电视架

1

2

3

电视架或三脚架安装

用户可以自行选购电视架或三脚架来固定终端，电视架或三脚架的选购要求与使用吊装方式时的支架要求相同。电视架或三脚架安装步骤与

吊装步骤相同。

螺丝规格：

1/4-20UNC英制螺钉

连接终端

如果你无需使用VCH50进行演示，可以使用网线将VCM34的PoE接口直接连在终端的VC Hub/Phone接口上。

我们要求使用Yealink原装电源（48V/0.7A），使用第三方电源可能会导致终端损坏。如果使用过程中发现线缆破皮，请立即更换。

7.5米网线

3米网线

电源适配器

显示设备x2

1.8米HDMI线

VCH50

MINI DP HDMI

Codec

Audio

VCM34

CTP20

7.5米网线

3米网线

如果终端搭配CTP20和VCM34套件，请按下图完成连接：

PoE

15

VCH50

7.5米网线

1.2米Mini-DP线 1.2米HDMI线

或

MINI DP HDMI

Codec

Audio

终端上的

VC Hub/Phone口

连接有线辅流

想要了解WPP20无线传屏助手的详细信息，请参阅亿联WPP20无线传屏助手快速入门指南。

连接无线辅流

PC

WPP20无线传屏助手

WF50 USB无线网络适配器

PC

VCH50

7.5米网线

3米网线

电源适配器

显示设备x2

1.8米HDMI线

0.5米网线

CP960会议电话

有线扩展麦

MINI DP HDMI

Codec

Audio

如果终端搭配电话会议套件，请按下图完成连接：

如果你无需使用VCH50进行演示，可以使用7.5米网线将CP960会议电话的Internet接口直接连在终端的VC Hub/Phone接口上。

CP960会议电话连接在终端上时，3.5mm音频输出接口和Micro USB接口不可用。

视频会议室的部署可分为如下几个模块：光线、摄像机放置、拾音/声音播放、画面显示、接线。以下是针对这些模块的具体建议，在会

议室装修与视频会议设备部署的过程中可参考以下内容取得更佳的视频会议效果。

视频会议室部署

45

。

摄像机放置

光线

会议室的灯光应更多地聚焦在会议桌与参会人的位置，以

45° 斜照向参会人面部是较为理想的光照条件。

如会议室原有的光线不足可考虑加装平面光源，色温以

4000~5000k，光照强度以300~500lux为宜。光线充足与

否可以视频画面中面部肤色是否真实还原作为评判标准。

即使会议室采光条件良好，也建议在会议过程中打开会议室

灯光，以确保会议桌与参会人区域有充足且均匀的光照度。

摄像机避免正对强光源，例如窗户。以免出现人物图像逆光

现象。如果摄像机不可避免地朝向窗口，可装配窗帘。

根据实际的会议室情况，摄像机安装高度建议在 1.55~1.85

m之间。如果是较大型的会议室/会场则不受限于此建议高

度，可根据被摄物体距离确定摄像机高度。

16

使用遥控器与束线带

1.55 (m)

1.85 (m)

1.5 (m)

参会者与麦克风的距离在0.5~1.5m范围内可获得最佳的

拾音效果。

当会议室面积大于50或会议桌长于4m时建议配备扩展

麦克风或采用多个麦克风。

会议电话的内置扬声器通常能够满足60以下会议室的

需求。当会议室面积大于60时可考虑级联会议电话或

连接外部音响，确保声音有效覆盖所有参会人。

如使用电视扬声器播放声音，将电视音量调整到合适的大

小，避免音量过大出现破音。麦克风应与电视保持一定距

离，建议大于2m。

拾音/声音播放

因投影仪的显示效果相对较差且容易受到光照情况影响，

所以建议使用液晶电视作为视频会议的显示设备。如需同

时使用电视和投影仪，尽可能将电视放置在靠近投影仪的

位置，减少视线跨度。

由于投影效果易受光照情况影响，在使用投影仪时应尽可

能减少照射向投影幕的灯光，增加参会者区域的光照度。

如果使用辅流的需求较多，建议使用双屏显示，如此可同

时全屏观看视频画面与辅流内容。

画面显示

，

电视电视

17

建议将摄像机放置于电视顶部水平居中的位置。如果显示设

备较大（大于80寸）或应用了拼接屏，可考虑将摄像机固定

在显示设备下方，但应高于会议桌高度。为提升视频会议中

的眼神交流与互动感，尽可能将摄像机靠近显示对方视频画

面的屏幕。

投影+电视作为显示设备的情况下，将电视架推车尽可能靠

近投影幕布，摄像机放置于电视上靠近投影幕布的一侧。

面积较大的会议室/会场可考虑吊顶倒装摄像机，但需避免

摄像机直接安装于天花板推荐使用吊架降低摄像机高度。需

注意摄像机高度/角度调节范围相对第一排参会者距离的关

系。以摄像机离地 2.5m为例，第一排参会者与摄像机的距

离应至少 2m为宜。

如需多角度画面或更广的视角范围，可选购扩展摄像机

VCC22。

尽可能选择具备线材收纳功能的会议桌，以确保桌面整洁

如果会议室未进行走线设计，电视至桌面的线材可使用金

属线槽贴地走线。

遇到线长不够需要更换线材或需要转接的情况，请联系代

理商或拨打技术支持热线咨询技术人员确定线材规格，避

免自行配线影响使用效果，甚至造成不必要的损失。

线材

电视

。

18

网络快速部署

网络带宽需求

终端所需网络带宽需求为上下行带宽需求，网络的上行带宽及下行带宽均需要满足需求

以上带宽需求为两方通话的带宽需求，主会场带宽需要根据分会场数量进行相应的增加

部署网络

你可以使用云服务方式或传统方式部署终端。

云服务方式部署

云服务方式部署无需复杂的网络配置，登录云平台就可以实现各会场间的互联互通。账号信息请从管理员处获取。

通过遥控器登录平台：

1. 选择更多->设置->高级设置（默认密码：0000）->视频会议服务平台。

2. 勾选启用云功能复选框。

3. 从登录平台下拉框中选择你想要登录的平台。

4. 填写平台登录的相关信息并登录。

传统方式部署

请根据你的会场所处的角色进行设置，主会场必须公网可达，分会场可参考主会场设置或采用智能穿透方式部署。

全高清视频1080P 1.3Mb

2.6Mb人像1080P+内容1080P

建议带宽需求

视频分辨率

ページが読み込まれています...

Yealink VC800 Full HD Video Conferencing System 中英 V40.10 クイックスタートガイド

Yealink VC800 Full HD Video Conferencing System 中英 V40.10 クイックスタートガイド

他の言語で

関連論文

その他のドキュメント