English
Refrigerator
user manual
imagine the possibilities
Thank you for purchasing a Samsung product.
To receive a more complete service,
please register your product at
www.samsung.com/register
Free Standing Appliance
This manual is made with 100 % recycled paper.
DA99-02028F-06.indb 01DA99-02028F-06.indb 01 13. 6. 19. 1:5313. 6. 19. 1:53
02_ safety information
SAFETY INFORMATION
• Before operating the appliance, please
read this manual thoroughly and retain it
for your reference.
• Because these following operating
instructions cover various models, the
characteristics of your refrigerator may
differ slightly from those described in this
manual.
CAUTION/WARNING SYMBOLS USED
WARNING
Indicates that a danger of death or
serious injury exists.
CAUTION
Indicates that a risk of personal injury or
material damage exists.
OTHER SYMBOLS USED
Represents something you must NOT do.
Represents something you must NOT
disassemble.
Represents something you must NOT
touch.
Represents something you must follow.
Indicates that you must disconnect the
power plug from the socket.
Represents a ground is needed to prevent
electric shock.
It is recommended that this symbol be
handled by service man.
These warning signs are here to prevent injury to
you and others.
Please follow them explicitly.
After reading this section, keep it in a safe place
for future reference.
• This refrigerator must be properly installed and
located in accordance with the manual before it
is used.
• Use this appliance only for its intended purpose
as described in this instruction manual.
• We strongly recommend that any servicing be
performed by a qualified individual.
• R600a or R134a can be used as a refrigerant.
Check the compressor label on the rear of the
appliance and the rating label inside the fridge to
see which refrigerant is used for the refrigerator.
• In case of R600a refrigerant, this gas
is natural gas with high environmental
compatibility that is, however, also
combustible. When transporting and
installing the appliance, care should
be taken to ensure that no parts of the
refrigerating circuit are damaged.
• Refrigerant squirting out of the pipes could ignite
or cause an eye injury. If a leak is detected,
avoid any naked flames or potential sources of
ignition and air the room in which the appliance is
standing for several minutes.
• In order to avoid the creation of a flammable
gas-air mixture if a leak in the refrigerating
circuit occurs, the size of the room in
which the appliance may be sited depends
on the amount of refrigerant used.
• Never start up an appliance showing any signs of
damage. If in doubt, consult your dealer.
• The room must be 1m
3
in size for every 8g of
R600a refrigerant inside the appliance.
• The amount of refrigerant in your particular
appliance is shown on the identification plate
inside the appliance.
• Please dispose of the packaging material for this
product in an environmentally friendly manner.
• This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience
and knowledge, unless they have been given
supervision or instruction concerning use of the
appliance by a person responsible for their safety.
• Children should be supervised to ensure that they
do not play with the appliance.
safety information
WARNING
WARNING
WARNING
DA99-02028F-06.indb 02DA99-02028F-06.indb 02 13. 6. 19. 1:5313. 6. 19. 1:53
safety information _03
SEVERE WARNING SIGNS
• Do not install the refrigerator in a damp
place or place where it may come in
contact with water.
- Deteriorated insulation of electrical parts may
cause an electric shock or fire.
• Do not place this refrigerator in direct sunlight or
expose to the heat from stoves, room heaters or
other appliance.
• Do not plug several appliances into the same
multiple power board. The refrigerator should
always be plugged into its own individual
electrical which has a voltage rating that matched
the rating plate.
- This provides the best performance and also
prevents overloading house wiring circuits, which
could cause a fire hazard from overheated wires.
• Make sure that the power plug is not squashed
or damaged by the back of the refrigerator.
• Do not bend the power cord excessively or place
heavy articles on it.
- This constitutes a fire hazard.
• Have the power cord repaired or replaced
immediately by the manufacturer or its service
agent if power cord has become frayed or
damaged.
• Do not use a cord that shows cracks or abrasion
damage along its length or at either end.
• If the power cord is damaged, have it replaced
immediately by the manufacturer or its service
agent.
• When moving the refrigerator, be careful not to
roll over or damage the power cord.
• Do not insert the power plug with wet hands.
• Unplug the refrigerator before cleaning and
making repairs.
• Do not use a wet or damp cloth when cleaning
the plug.
• Remove any foreign matter or dust from the
power plug pins.
- Otherwise there is a risk of fire.
• If the refrigerator is disconnected from the power
supply, you should wait for at least ten minutes
before plugging it back.
• If the wall socket is loose, do not insert the power
plug.
- There is a risk of electric shock or fire.
• The appliance must be positioned so that the
plug is accessible after installation.
• The refrigerator must be grounded.
- You must ground the refrigerator to
prevent any power leakages or electric
shocks caused by current leakage from
the refrigerator.
• Never use gas pipes, telephone lines or
other potential lightening rods as ground.
- Improper use of the ground plug can result
in electric shock.
• Do not dissemble or repair the refrigerator by
yourself.
- You run risk of causing a fire, malfunction and/or
personal injury.
• If you smell pharmaceutical or smoke, pull
out power plug immediately and contact your
Samsung electronics service center.
• Keep ventilation opening in the appliance
enclosure or mounting structure clear of
obstruction.
• Do not use mechanical devices or any other
means to accelerate the defrosting process, other
than those recommended by the manufacturer.
• Do not damage the refrigerant circuit.
• Do not place or use electrical appliance inside
the refrigerator/freezer, unless they are of a type
recommended by the manufacturer.
• The appliance is not intended for use by children
or infirm persons without supervision.
• Children should be supervised to ensure that they
do not play with the appliance.
• Do not let children hang on the door. If not, a
serious injury may occur.
• Do not touch the inside walls of the freezer or
products stored in the freezer with wet hands.
- This may cause frostbite.
• If the refrigerator is not to be used for a long
period of time, pull out the power plug.
- Deterioration in the insulation may cause fire.
• Do not store articles on the top of the appliance.
- When you open or close the door, the articles
may fall and cause personal injury and/or material
damage.
CAUTION SIGNS
• This product is intended only for the
storage of food in a domestic environment.
• Manufacturer’s recommended storage times
should be adhered to. Refer to relevant
instructions
• Bottle should be stored tightly together so that
they do not fall out.
• Do not place carbonated or fizzy drinks in the
freezer compartment
• Do not put bottles or glass containers in the
freezer.
- When the contents freeze, the glass may break
and cause personal injury.
•
Do not spray inflammable gas near the refrigerator.
- There is a risk of explosion or fire.
• Do not directly spray water inside or outside the
refrigerator.
CAUTION
WARNING
DA99-02028F-06.indb 03DA99-02028F-06.indb 03 13. 6. 19. 1:5313. 6. 19. 1:53
04_ safety information
- There is a risk of fire or electric shock.
• Do not store volatile or flammable substances in
the refrigerator.
- The storage of benzene, thinner, alcohol, ether,
LP gas and other such products may cause
explosions.
• If you have a long vacation planned, you must
empty the refrigerator and turn it off.
• Do not store pharmaceuticals products, scientific
materials or temperature-sensitive products in the
refrigerator.
- Products that require strict temperature controls
must not be stored in the refrigerator.
• Do not put a container filled with water on the
refrigerator.
- If spilled, there is a risk of fire or electric shock.
• Do not apply strong shock or excessive force
onto the surface of glass.
- Broken glass may result in a personal injury and/
or property damage.
CAUTION SIGNS FOR
CLEANING
• Never put fingers or other objects into the
dispenser hole and ice chute.
- It may cause personal injury or material damage.
• Do not use a wet or damp cloth when cleaning
the plug, remove any foreign material or dust
from the power plug pins.
- Otherwise there is a risk of fire.
• If the refrigerator is disconnected from the power
supply, you should wait for at least five minutes
before plugging it back.
WARNING SIGNS FOR
DISPOSAL
•
When disposing of this or other refrigerator/s,
remove the door/door seals, door latch so that small
children or animals cannot become trapped inside.
• Leave the shelves in place so that children may
not easily climb inside.
• R600a or R134a is used as a refrigerant. Check
the compressor label on the rear of the appliance
or the rating label inside the fridge to see which
refrigerant is used for your refrigerator. When
this product contains flammable gas(Refrigerant
R600a) contact your local authority in regard to
safe disposal of this product.
• Cyclopentane is used as a insulation blowing gas.
The gases in insulation material require special
disposal procedure. Please contact your local
authorities in regard to the environmentally safe
disposal of this product. Ensure that none of the
pipes on the back of the appliances are damaged
prior to disposal. The pipes shall be broke in the
open space.
In the event of a power failure, call the local
offi ce of your Electricity Company and ask
how long it is going to last.
Most power failures that are corrected in an hour or
two will not affect your refrigerator temperatures.
However, you should minimize the number of door
openings while the power is off.
But should the power failure last more than 24hours,
remove all frozen food.
For doors or lids fi tted with locks and keys, the keys
be kept out of the reach of children and not in the
vicinity of the refrigerating appliance, in order to
prevent children from being locked inside.
ADDITIONAL TIPS FOR PROPER
USAGE
• Allow the appliance to stand for 2hours
after installation.
• To get best performance of product,
- Do not place foods too closely in front of
the vents at the rear of the appliance as it
can obstruct free air circulation in the freezer
compartment.
- Wrap the food up properly or place it in airtight
containers before put it into the fridge freezer
- Do not put any newly introduced food for freezing
near to already frozen food.
• Do not place carbonated or fizzy drinks in the
freezer compartment
• Please observe maximum storage times and
expiry dates of frozen goods.
• There is no need to disconnect the refrigerator
from the power supply if you will be away for
less than three weeks. But, remove all the food if
you are going away for the three weeks or more.
Unplug the refrigerator and clean it, rinse and dry.
• Most power failures that are corrected in an
hour or two will not affect your refrigerator
temperatures. However, you should minimize
the number of door openings while the power is
off. But should the power failure last more than
24hours, remove all frozen food.
• If the key is provided with refrigerator, the keys
should be kept out of the reach of children and
not in the vicinity of the appliance.
• The appliance might not operate consistently
(possibility of defrosting of contents or
temperature becoming too warm in the frozen
food compartment) when sited for an extended
CAUTION
DA99-02028F-06.indb 04DA99-02028F-06.indb 04 13. 6. 19. 1:5313. 6. 19. 1:53
safety information _05
period of time below the cold end of the range of
temperatures for which the refrigerating appliance
is designed.
• Do not store food which goes bad easily at low
temperature, such as bananas, melons.
• Place the ice tray at the originally provided
posistion by manufacturer in order to achieve
optimal ice-freezing.
• Your appliance is frost free, which means there is
no need to manually defrost your appliance, as
this will be carried out automatically.
• Temperature rising during the defrost can comply
with ISO requirement. But If you want to prevent
an undue rise in the temperature of the frozen
food while defrosting the appliance, please wrap
the frozen food in several layers of paper such as
newspaper.
• Any increase in temperature of frozen food during
defrosting can shorten its storage life.
contents
SETTING UP YOUR SIDE-BY-SIDE REFRIGERATOR ……………………………………………………… 06
OPERATING THE SAMSUNG SIDE-BY-SIDE REFRIGERATOR …………………………………………… 15
TROUBLESHOOTING …………………………………………………………………………………………… 21
DA99-02028F-06.indb 05DA99-02028F-06.indb 05 13. 6. 19. 1:5313. 6. 19. 1:53
06_ setting up
GETTING READY TO INSTALL
THE REFRIGERATOR
Congratulations on the purchase of your Samsung
Side-By-Side Refrigerator. We hope you will enjoy
the many state-of-the-art features and effi ciencies
that this new appliance has to offer.
Selecting the best location for the
refrigerator
• Select a location with easy access to the water
supply.
• Select a location without direct exposure to
sunlight.
• Select a location with level (or nearly level)
flooring.
• Select a location with enough space for the
refrigerator doors to open easily.
• Overall space required in use. Refer to drawing
and dimension as below.
• Please ensure that appliance can be moved freely
in the event of maintenance & service.
• Allow clearance to the right, left, back and
top when installing. This will help reduce
power consumption and keep your energy
bills lower.
• Do not install the refrigerator where the
temperature will go below 50°F (10°C).
• Make sure you disconnect the water supply line
BEFORE removing the freezer door.
See the next section on “Separating the Water
Line” to avoid damage.
When installing, servicing or cleaning behind
the refrigerator, be sure to pull the unit
straight out and push back in straight after
fi nishing.
setting up your side-by-side
refrigerator
25mm
25mm
at least 50mm
at least 50mm
at least 50mm
at least 50mm
CAUTION
DA99-02028F-06.indb 06DA99-02028F-06.indb 06 13. 6. 19. 1:5313. 6. 19. 1:53
setting up _07
01 SETTING UP
1. With the Freezer door closed, remove the upper
hinge cover
1
using a screwdriver, and then
disconnect the wires by gently pulling them apart
2
.
2. Remove hinge screws
3
and the ground screw
4
by turning counter-clockwise, and take off the
upper hinge
5
. Be careful that the door does not
fall on you as you are removing it
3. Next, remove the door from the lower hinge
6
by carefully lifting the door straight up
7
.
Be careful not to pinch the water tubing and
wire harness on the door.
4. Remove the lower hinge
8
using a hex wrench.
REMOVING THE
REFRIGERATOR DOORS
If your entrance won’t allow the refrigerator to pass
easily through it, you can remove the doors.
1. Removing the Front Leg Cover
First, open both the freezer and refrigerator doors,
and then take off the front leg cover by turning the
three screws counter-clockwise.
Separating the Water Supply Line
from the Refrigerator
1. Remove the water line by pressing the coupler
1
and pulling the water line
2
away.
Do not cut the water line. Gently separate it
from the coupler.
2. Removing the freezer door
A few things to mention fi rst.
• Make sure that you lift the door straight up so the
hinges are not bent or broken.
• Be careful not to pinch the water tubing and wire
harness on the door.
• Place doors on a protected surface to prevent
scratching or damage.
1
2
2
1
3
4
5
7
6
DA99-02028F-06.indb 07DA99-02028F-06.indb 07 13. 6. 19. 1:5313. 6. 19. 1:53
08_ setting up
REATTACHING THE
REFRIGERATOR DOORS
Once you have safely placed your refrigerator where
you plan for it to stay, it is time to put the doors back
on.
Reattaching the Freezer Door
1. Replace the freezer door by inserting the water
line
1
back into the lower corner of the door and
then into the hole on the lower hinge
2
.
Gently pull the water line back down so that it
runs straight, with no kinks or bends.
2. Insert the upper hinge shaft
3
into the hole on
the corner of the freezer door
4
.
Make sure the hinge is level between the upper
hinge hole
5
and the hole of the cabinet
6
and
reattach the hinge screws
7
and ground screw
8
by turning in a clockwise direction.
Reconnect the wires.
3. Place the front part of the upper hinge cover
9
on the front of the upper hinge
10
and reattach
with the screw.
Removing the Fridge Door
1. With the door closed, remove the upper hinge
cover
1
using a screwdriver.
2. Remove hinge screws
2
and the ground screw
3
by turning counter-clockwise, and take off the
upper hinge
4
. Be careful that the door does not
fall on you as you are removing it
3. Remove the door from the lower hinge
5
by
lifting the door straight up
6
.
4. Remove the lower hinge
7
from the bracket
8
by gently lifting the lower hinge upwards.
1
4
2
3
10
9
4
5
6
7
8
3
1
2
DA99-02028F-06.indb 08DA99-02028F-06.indb 08 13. 6. 19. 1:5313. 6. 19. 1:53
setting up _09
01 SETTING UP
Reattaching the Water Supply Line
1. Insert the water line
2
into the coupler
1
.
2. The Water Line must be fully Inserted to the
center of transparent coupler to prevent water
leakage from the dispenser.
3. Insert the clip in the install pack and check that it
holds the line firmly.
Reattaching the Front Leg Cover
Before attaching the cover, check water
connector for leakage.
Replace the front leg cover by turning the
three screws clockwise, as shown in the
fi gure.
Reattaching the Fridge Door
1. Insert the lower hinge
1
back into the lower
hinge bracket
2
.
2. Fit the hole in the corner of the fridge door
3
over the lower hinge
4
.
3. Insert the upper hinge shaft
5
into the hole
on the hinge
6
. Make sure the hinge is level
between the upper hinge hole
7
and the hole on
the top of the cabinet
8
. Then, reattach hinge
screws
9
and the ground screw
10
by turning it
in a clock wise direction.
4. Place the front part of the upper hinge cover
11
on the front of the upper hinge
12
and reattach it
with the screw.
Center of transparent
Center of transparent
coupler
coupler
clip A (1/4”)
clip A (1/4”)
(6.35mm)
(6.35mm)
1
2
3
4
12
11
1
2
DA99-02028F-06.indb 09DA99-02028F-06.indb 09 13. 6. 19. 1:5313. 6. 19. 1:53
10_ setting up
MAKING MINOR ADJUSTMENTS
TO THE DOORS
Remember, a level refrigerator is necessary for
getting the doors perfectly even. If you need
help, review the previous section on levelling the
refrigerator.
In the process for adjusting both the doors is the
same. Open the doors and adjust them, one at a
time, as follows:
1. Unscrew the
nut
1
from the
lower hinge until it
reaches the upper
end of the bolt
2
.
When you release the nut
1
, make sure
that you use the Allen wrench provided
3
to loosen the bolt
2
in a counter-clockwise
direction.
You should then be able to unscrew the nut
1
with your fi ngers.
2. Adjust the
height difference
between the doors
by turning the
bolt
2
clockwise
or counter
clockwise
.
When you turn clockwise
, the door will
move up.
3. After adjusting the
doors, turn the
nut
1
clockwise
until it
reaches the lower
end of the bolt,
then tighten the bolt again with the wrench
3
to
fix the nut in place
1
.
If you do not secure the nut fi rmly, the bolt
may release.
LEVELLING THE REFRIGERATOR
Now that the doors are back on the refrigerator, you
will want to make sure the refrigerator is level so you
can then make fi nal adjustments. If the refrigerator
is not level, it will not be possible to get the doors
perfectly even.
The front of the refrigerator is also adjustable.
When the Freezer door is lower than
the fridge
Insert a fl at-blade screwdriver into a notch on the
Leg, turn it clockwise or counter clockwise to level
the freezer.
When the Freezer door is lower than
the fridge
Insert a fl at-blade screwdriver into a notch on the
Leg, turn it clockwise or counter clockwise to level
the fridge.
Refer to the next section for the best way to
make very minor adjustments to the doors.
Leg
Leg
Screw Driver
Screw Driver
Screw Driver
Leg
Leg
Adjustment part
Adjustment part
When the door of the freezer is
When the door of the freezer is
higher than the fridge
higher than the fridge
3
2
1
Wrench
Wrench
Bolt
Bolt
Nut
Nut
3
2
Wrench
Wrench
Bolt
Bolt
lt i ith th
3
2
1
Wrench
Wrench
Bolt
Bolt
Nut
Nut
DA99-02028F-06.indb 10DA99-02028F-06.indb 10 13. 6. 19. 1:5413. 6. 19. 1:54
setting up _11
01 SETTING UP
4. After connecting the water supply to the water
filter, turn your main water supply back on and
dispense about 1l to clear and prime the water
filter.
Connecting the water line to the
refrigerator
1. Remove the dust cap from the water line on the
rear of the unit and fit a compression nut from the
install kit.
2. Remove the water pipe from the install kit and fit
a compression nut to one end.
3. Join the two pipes together using the
compression joint from the install kit ensuring that
the joint is water tight.
4. Join the other end of the install pipe to the main
water supply and turn on the water to check for
leaks.
Only connect the water line to a drinkable
water source. If you have to repair or
disassemble the water line, cut off 6.5mm
of the plastic tubing to make sure you get a
snug, leak-free connection.
Before being used, the leakage in these
places should be examined
CHECKING THE WATER
DISPENSER LINE (OPTIONAL)
A water dispenser is just one of the helpful features
on your new Samsung refrigerator. To help promote
better health, the Samsung water fi lter removes
unwanted particles from your water. However, it
does not sterilize or destroy microorganisms. You
will need to purchase a water purifying system to do
that. In order for the icemaker to operate properly,
water pressure of 138 ~862 Kpa is required. Under
normal conditions, a 170 cc paper cup can be fi lled
in 10 seconds. If the refrigerator is installed in an
area with low water pressure (below 138 Kpa), you
can install a booster pump to compensate for the
low pressure. Make sure the water storage tank
inside the refrigerator is properly fi lled. To do this,
press the water dispenser lever until the water runs
from the water outlet.
Water Line installation Kits are included. You
can fi nd it in one of the freezer drawers.
INSTALLING THE WATER
DISPENSER LINE
For Interior model
Parts for water line Installation
Connecting to the water supply line
1. First, shut off the main water supply line.
2. Locate the nearest cold, drinking water line.
3. Follow the water line installation instructions in
the installation kit.
1
Water line fixer and screws
Water line fixer and screws
2
Pipe connector
Pipe connector
3
Water line
Water line
4
Water Filter
Water Filter
CAUTION
The water line must be connected to the cold
water pipe. If it is connected to the hot water
pipe, it may cause the purifier to malfunction.
Close Main
Close Main
Water pipe
Water pipe
Close Main
Close Main
Water pipe
Water pipe
No gap
No gap
Remove
Remove
cap
cap
Water Line
Water Line
from unit
from unit
Water Line
Water Line
from Kit
from Kit
No gap
No gap
Loosen a
Loosen a
CAUTION
DA99-02028F-06.indb 11DA99-02028F-06.indb 11 13. 6. 19. 1:5413. 6. 19. 1:54
12_ setting up
INSTALLING THE WATER
DISPENSER LINE
For Exterior model
Parts for water line Installation
Connecting to the water supply line
Connect the water pipe with coupler and tap.
1. Close the main water tap.
2. Connect coupler “A” to the tap.
Select the location where the purifi er
is to install. (Model with the purifi er)
- If you wish to reassemble the water inlet
and outlet sides of the purifier during purifier
installation, see the reference illustration.
- Cut the water line attached to the purifier to the
appropriate place after measuring the distance
between the purifier and the cold water tap.
• Samsung Warranty does not cover WATER LINE
INSTALLATION.
• The cost of connection to a water supply is at the
customer expense, unless included in the delivery
charge (refer to the delivery agreement with the
seller)
• Please contact Plumber or Authorised Installer for
the installation if needed.
• If Water leakage occurs due to improper
installation, Please contact installer.
Water line fixer and screws
Water line fixer and screws
Pipe connector
Pipe connector
Water line
Water line
Purifier lock-clip
Purifier lock-clip
Purifier
Purifier
CAUTION
The water line must be connected to the cold water
pipe. If it is connected to the hot water pipe, it may
cause the purifi er to malfunction.
WARRANTY INFORMATION
This water line installation is not covered by the
refrigerator or ice maker manufacturer’s warranty.
Follow these instructions carefully to minimise the risk of
expensive water damage.
Note:
If the coupler does not fi t on the current tap, go the
nearest authorised service dealer and purchase the right
couplers fi ttings.
DA99-02028F-06.indb 12DA99-02028F-06.indb 12 13. 6. 19. 1:5413. 6. 19. 1:54
setting up _13
01 SETTING UP
Remove any residual matter inside
the purifi er. (Model with the purifi er)
- Open the main water tap to check whether water
is running through the water tube on the water
inlet side of the purifier.
- If water does not come out through the line,
check whether the tap is open.
- Leave the tap open until clean water is running
out and any residual matter that built up during
manufacturing has been removed.
Attach the purifi er lock-clip.
- Hold the purifier lock-clip in the appropriate
position (under the sink for example) and fix it
tightly into place where to screw.
Secure the purifi er in position.
- Fix the purifier in position, as shown in the figure
on the right.
Replacement Instructions
1. Shut off water supply.
2. Note the Flow direction on the filter.
3. Insert water supply tube into the inlet side of the
filter until the tube stop.
4. After inserting tube, put together the clip strongly.
The Clip fix the tube.
5. Turn on the water and check for leaks. If leaks
occur, repeat step 1,2,3,4. If leaks persist,
discontinue use and call your supporting dealer.
6. Flush filter for 5 minutes before use.
COUPLER “A”
COUPLER “A”
TAP
TAP
COUPLER
COUPLER
SIDE OF
SIDE OF
PURIFIER
PURIFIER
WATER INLET
WATER INLET
SIDE OF PURIFIER
SIDE OF PURIFIER
LINE OUTLET
LINE OUTLET
90 degree
90 degree
PURIFIER WATER
PURIFIER WATER
CAUTION
Locking Clip
Locking Clip
Insert Locking Clip After
Insert Locking Clip After
tube seated
tube seated
WATER SUPPLY
WATER SUPPLY
INLET SIDE
INLET SIDE
PERMEAT
PERMEAT
FLOW DIRECTION
FLOW DIRECTION
Note : You must also ensure that
the cut is square and not
at any sort of angle as
this could cause a leak
WATER LINE
WATER LINE
PURIFIER
PURIFIER
WATER
WATER
OUTLET SIDE OF
OUTLET SIDE OF
PURIFIER
PURIFIER
PURIFIER LOCK-CLIP
PURIFIER LOCK-CLIP
WATER TUBE
WATER TUBE
PURIFIER LOCK-CLIP
PURIFIER LOCK-CLIP
PURIFIER
PURIFIER
DA99-02028F-06.indb 13DA99-02028F-06.indb 13 13. 6. 19. 1:5413. 6. 19. 1:54
14_ setting up
Check the amount of water supplied
to the ice tray.
1. Lift up the icemaker cover and gently pull out.
2. When you press the Test button for 3 seconds,
the ice cube container is filled with water from
the water supply tap. Check to make sure the
amount of water is correct (see the illustration
below).
If the water level is too low, the ice cubes will be
small. This is a water pressure problem from with
in the main water pipes, not the refrigerator.
Using the anti-sweat heater switch
When the humidity of the indoor is high, sweat
may form around the beverage station & dispenser.
Turn the Anti-sweat heater switch on, to remove
the sweat and turn the switch off when the sweat
disappears.
Connect the water line to the
refrigerator.
- Remove the compressor cover of the refrigerator.
- Connect the water line to the valve, as shown in
the figure.
- When connected, check if there is any leakage.
If any, repeat the connection.
- Reattach the compressor cover of the refrigerator.
Secure the water line.
- Using clip ”A”, fix the water
line to the wall (the back of
refrigerator).
- When the water line is
secure, make sure whether
the water line is not
excessively bent, pinched or
squashed.
Removing any residual matter inside
the water supply line after installing
fi lter.
1. Turn ON the main water supply & turn OFF the
valve to the water supply line.
2. Run water through the dispenser until the water
runs clear (approx. 1L). This will clean the water
supply system and remove air from the lines.
3. Additional flushing may be required in some
households.
4. Open the refrigerator door and make sure there
are no water leaks coming from the water filter.
A newly installed water fi lter cartridge may
cause water to briefl y spurt from the water
dispenser. This is due to air getting into the
line. It should pose no problem to operation.
RS21/23H** (OPTIONAL)
WATER LINE
WATER LINE
INSTRUCTIONS
INSTRUCTIONS
COMPRESSOR COVER OF
COMPRESSOR COVER OF
REFRIGERATOR
REFRIGERATOR
CONNECTION NUT
CONNECTION NUT
CLIP A
CLIP A
WATER LINE
WATER LINE
Ice maker
1
Feeler Arm
2
Test button
Check the water level
DA99-02028F-06.indb 14DA99-02028F-06.indb 14 13. 6. 19. 1:5413. 6. 19. 1:54
operating _15
02 OPERATING
OPERATING THE REFRIGERATOR
Using the Control Panel /
Digital Display
When not in use the temperature display will turn off,
this is normal.
1
POWER
FREEZE
BUTTON
Speeds up the time needed to
freeze products in the freezer. This
can be helpful if you need to quickly
freeze items that spoil easily or if
the temperature in the freezer has
warmed dramatically (For example, if
the door was left open).
2
FR
EEZER
BUTTON
Press the Freezer button to set the
freezer to your desired temperature,
You can set the temperature
between -14°C (8°F) and -25ºC
(-14°F).
3
ICE TYPE
BUTTON
Use this button to choose Cubed,
Crushed or to turn the Ice feature
off.
4
FILTER
CHANGE
BUTTON
When you change the fi lter, press
this button for 3 seconds to reset
the fi lter schedule.
5
POWER
COOL
BUTTON
Press this button to quickly
return the refrigerator to the set
temperature.
Press this button again to cancel the
Power Cool mode.
6
CHILD LOCK
FUNCTION
By pressing the Power Cool
button and the Fridge button
simultaneously for 3 seconds, all
buttons will be locked. The Water
dispenser lever and the Ice lever
will not work either. To cancel this
function, Press these two buttons
for 3 seconds again.
7
FRIDGE
BUTTON
Press the Fridge button to set the
fridge to your desired temperature.
You can set temperature between
1°C and 7°C (34°F and 45°F).
When you use Power Freeze the energy
consumption of the refrigerator will increase.
Remember to turn it off when you don’t
need it and return the freezer to your original
temperature setting.
If you need to freeze large amount of food
stuff, activate Power Freeze function at least
24 hours before.
operating the SAMSUNG side-
by-side refrigerator
5
6
7
1
3
4
2
COOLSELECT MODEL
DISPENSER MODEL
NORMAL MODEL
DA99-02028F-06.indb 15DA99-02028F-06.indb 15 13. 6. 19. 1:5413. 6. 19. 1:54
16_ operating
USING THE ICE AND COLD
WATER DISPENSER
Press the Ice Type button to select the type of ice
you want
Ice is made in cubes. When you select
“Crushed”, the icemaker grinds the ice cubes
into crushed ice.
Dispensing ice
Place your glass underneath the ice outlet and
push gently against the ice dispenser lever with
your glass. Make sure the glass is in line with the
dispenser to prevent the ice from bouncing out.
Using the Water Dispenser
Place a glass underneath the water outlet and
push gently against the water dispenser lever with
your glass. Make sure the glass is in line with the
dispenser to prevent the water from splashing out.
CONTROLLING THE
TEMPERATURE
CONTROLLING THE FREEZER
TEMPERATURE
The freezer temperature can be set between -14°C
(8°F) and -25ºC (-14°F) to suit your particular needs.
Press the Freezer button repeatedly until the desired
temperature is shown in the temperature display.
Keep in mind that foods like ice cream may melt at
-16ºC (4°F).
The temperature display will move sequentially from
-14°C (8°F) and -25ºC (-14°F). When the display
reaches -14ºC (8°F), it will begin again at -25ºC
(-14°F).
Five seconds after the new temperature is set the
display will again show the actual current freezer
temperature. However, this number will change as
the Freezer adjusts to the new temperature.
CONTROLLING THE FRIDGE
TEMPERATURE
The refrigerator temperature can be set between 7ºC
(46°F) and 1ºC (34°F) to suit your particular needs.
Press the Fridge button repeatedly until the desired
temperature is shown in the temperature display.
The temperature control process for the Fridge
works just like the Freezer process. Press the Fridge
button to set your desired temperature. After a few
seconds, the Fridge will begin tracking towards the
newly set temperature. This will be refl ected in the
digital display.
The temperature of the freezer or the
refrigerator may rise from opening the doors
too frequently, or if a large amount of warm
or hot food is placed in either side. This may
cause the digital display to blink. Once the
freezer and refrigerator return to their normal
set temperatures the blinking will stop. If the
blinking continues, you may need to “reset”
the refrigerator. Try unplugging the appliance,
wait about 10 minutes and then plug back in.
No Ice
Select this if you want to
turn off the icemaker
DA99-02028F-06.indb 16DA99-02028F-06.indb 16 13. 6. 19. 1:5413. 6. 19. 1:54
operating _17
02 OPERATING
USING THE COOLSELECT
ZONE™ DRAWER (OPTIONAL)
Quick Cool
• You can use the Quick Cool feature with the
CoolSelect Zone™.
• “Quick Cool” allows 1~3 canned beverages to
cool within 60 min.
• To cancel this function, press the “Quick Cool”
button again. CoolSelect Zone™ returns to the
previous temperature.
• When “Quick Cool” ends, it returns to the “Cool”
temperature setting.
Thaw
• Drips loss and quality deterioration of meats
reduces the freshness of foods.
• After “Thaw” is selected, warm and cold air is
alternately supplied into the CoolSelect Zone™
Drawer.
• Depending on the weight of meat, thawing time
can be selected for 4 hrs, 6 hrs, 10 hrs, and 12
hrs sequentially.
• When “Thaw” ends, CoolSelect Zone™ display
returns to “Zero Zone” condition.
• When “Thaw “ ends, there are no juice in the
meats and they are half-freezed condition so it is
easy to cut them for cooking.
• To cancel this option, press any button except
“Thaw”.
• The approximate thawing time of meat and fish
are shown below. (Based on 1inch thickness)
THAW TIME WEIGHT
4 hours 363g (0.8Ib)
6 hours 590g (1.3Ib)
10 hours 771g (1.7Ib)
12 hours 1000g (2.2Ib)
Depending on the size and thickness of meat
and fi sh, the thawing time may vary.
The above weight represents the total weight
of food in the CoolSelect Zone™ Drawer.
Ex) The total thawing time for 400g frozen
beef and 600g frozen chicken will be 10
hours.
With the “Thaw” option, food which is not
needed to thaw in the CoolSelect Zone™
Drawer should be removed.
• Do not put your fingers, hands or any
other unsuitable objects in the chute or
ice-maker bucket.
- It may result in personal injury or material
damage.
• Never put finger or any other objects in the
dispenser opening.
- It may cause injury.
• Use only the ice maker provided with the
refrigerator.
• The water supply to this refrigerator must only be
installed/connected by a suitably qualified person
and connect to a potable water supply only.
• In order to operate the ice maker properly, water
pressure of 138 ~ 862 Kpa is required.
• If you have a long vacation or business trip
and won’t use water or ice dispensers,
close the water valve.
- Otherwise, water leakage may occur.
• Wipe excess moisture from the inside and leave
the doors open.
- Otherwise, odor and mold may develop.
To get more space,you can remove top freezer
drawer since it does not affect thermal and
mechanical characteristics. A declared storage
volume of frozen food storage compartment is
calculated with this drawer removed.
CAUTION
WARNING
WARNING
DA99-02028F-06.indb 17DA99-02028F-06.indb 17 13. 6. 19. 1:5413. 6. 19. 1:54
18_ operating
REMOVING THE FREEZER
ACCESSORIES
Cleaning and rearranging the interior of the freezer
is simple.
1. Remove the Glass shelf by pulling the shelf out as
far as it will go. Then, gently lift it up and remove
it.
2. Remove the door bin by holding the door bin with
both hands and then gently lift it up.
3. Remove the Plastic drawer by pulling it out and
slightly lifting it up.
4. Remove the Icemaker bucket by lifting up and
pulling it out.
Do not use excessive force when removing
the cover.
Otherwise, the cover may break and cause
injury.
Soft Freeze
• When “Soft Freeze” is chosen, the temperature
on the digtal panel displays -5ºC regardless of
the set temperature of the refrigerator.
• “Soft-Freeze” temperature helps keep meats and
fishes fresh longer.
• Can cut meat easily without drips.
Zero Zone (0ºC)
• When “Zero Zone” is chosen, the temperature
of the CoolSelect Zone™ Drawer is kept at 0 ºC
regardless of the set refrigerator temperature.
• “Zero Zone” temperature helps keep meat or fish
fresh longer.
Cool
• When “Cool” is chosen, the temperature will
be the same as the set temperature of the
refrigerator. The digital panel shows the same
temperature as that of the display panel.
• The CoolSelect Zone™ Drawer allows extra
refrigerator space.
Depending on the beverages, the cool-down
time may vary.
For “Quick Cool” option, food stored in
the CoolSelect Zone™ Drawer should be
removed.
WARNING
DA99-02028F-06.indb 18DA99-02028F-06.indb 18 13. 6. 19. 1:5413. 6. 19. 1:54
operating _19
02 OPERATING
Before removing any accessories, make sure
that no food is in the way.
When possible, remove the food altogether to
reduce the risk of accidents.
To get the best energy effi ciency of this
product, please leave all selves, drawers
and baskets on their original position like as
illustration in page (17).
CLEANING THE REFRIGERATOR
Do not use Benzene, Thinner or Clorox™ for
cleaning.
They may damage the surface of the
appliance and can create a risk of fi re.
Do not spray the refrigerator with water while
it is plugged in, as it may cause an electric
shock. Do not clean the refrigerator with
benzene, thinner or car detergent for risk of
fi r e .
REPLACING THE INTERIOR
LIGHT
For LED lamp, please contact service
engineer to replace it.
REMOVING THE FRIDGE
ACCESSORIES
1. Remove the spill Proof Glass Shelf by pulling the
shelf out as far as it will go. Then, gently lift it up
and gently remove it.
2. Remove the Vegetable & Fruit Drawer by pressing
on the indentations found on the inside left and
right sides of the Veggie Box/
Dry Box cover and remove
by pulling forward.
Holding the drawer with one
hand, lift it up a little bit while
pulling it forward and take it
out of the refrigerator.
3. Remove the Gallon Door Bin by holding the bin
with both hands and gently lifting it up.
4. The Z Shelf is attached to the cabinet wall.
Remove the wine shelf by sliding it up and gently
lifting the shelf out of the tabs.
Ensure that the Z Shelf is fi tted as shown in
the diagram and not upside down.
CAUTION
WARNING
CAUTION
DA99-02028F-06.indb 19DA99-02028F-06.indb 19 13. 6. 19. 1:5413. 6. 19. 1:54
20_ operating
6. Once you have completed this process, hold the
Ice Type button for 3 seconds to reset the filter
schedule.
7. Lastly, Dispense 1L of water through water
dispenser and throw away. Make sure that water
flows clearly again before drinking.
A newly installed water fi lter cartridge may
cause water to briefl y spurt from the water
dispenser. This is due to air getting into the
line. It should pose no problem to operation.
Ordering replacement fi lters
To order more water fi lter cartridges, contact your
authorised Samsung dealer.
USING THE DOORS
The refrigerator doors are equipped with a door
opening and closing feature that ensures that the
doors close all the way and are securely sealed.
After opening beyond a certain point, the door will
“catch” and remain open. When the door is ajar
ahead of the catch that allows it to stay open, it will
close automatically.
CHANGING THE WATER FILTER
To reduce risk of water damage to your
property DO NOT use generic brands of water
fi lers in your SAMSUNG Refrigerator. USE
ONLY SAMSUNG BRAND WATER FILTERS.
SAMSUNG will not be legally responsible
for any damage, including, but not limited to
property damage caused by water leakage
from use of a generic water fi lter. SAMSUNG
Refrigerators are designed to work ONLY
WITH SAMSUNG Water Filter.
The “Filter Indicator” light lets you know when it is
time to change your water fi lter cartridge.
When the fi lter indicator light changes to red, it is
time to change the fi lter.
To give you some time to get a new fi lter, the light
will come on up just before the capacity of the
current fi lter runs out.
Changing the fi lter on time provides you with the
freshest, cleanest water from your fridge.
1. Remove the water filter from the box and
put a month indicator sticker on the filter
as shown.
2. Place a sticker on the filter that dates six months
in the future. For example, if you are replacing the
water filter in March, put the “SEP” (September)
sticker on the filter to remind you to replace in
September. Normally filter life is about every 6
months.
3. Next, remove the fixed cap by turning it counter
clockwise.
4. Remove the new filter’s protective cap and
remove the old filter.
5. Position and insert the new filter into the filter
housing.
Slowly turn the water filter clockwise 90º to align
with the indication mark on the cover, locking
the filter in position. Make sure that the indicator
is lined up with the “lock” position. Do not over
tighten.
1
2
3
4
5
Align the
Align the
indication
indication
mark
mark
with lock
with lock
position
position
Cover filter
Cover filter
Sticker
Sticker
(month
(month
indicator)
indicator)
WARNING
DA99-02028F-06.indb 20DA99-02028F-06.indb 20 13. 6. 19. 1:5413. 6. 19. 1:54
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
Samsung RS21HNTPN ユーザーマニュアル
- カテゴリー
- サイドバイサイド冷凍冷蔵庫
- タイプ
- ユーザーマニュアル
他の言語で
- English: Samsung RS21HNTPN User manual
